Granulator CPM 9042-12

CPM Pellet Press 9042-12

Condition: ready for operation (used), functionality: fully functional, total height: 1,200 mm, total width: 580 mm, total length: 820 mm, input voltage: 230 V, The machine is designed for pitting plums, leaving the plums whole. Electrical connection: 230 V. Machine dimensions mm: 820 x 580 x h1200. Originally, the machine is equipped with 10 blades, but 2 blades were already lost when it was purchased, but this does not interfere with the operation process at all. Only the yield is slightly lower. Productivity with 8 blades: 100 fruits / 1 minute Hole diameter: 30 mm. Machine weight: 100 kg. Giodpfx Aajw H I Trj Asr

Year of construction: 2001, operating hours: 123 h, condition: ready for operation (used), machine/vehicle number: 123, Metal silo for storage of woodchips, etc. Technical description: Giodpfsftdv Uex Aa Aor silo DM: 5m Height: 8 m with outfeeding unit (screw conveyor connection to output) Cappacity: 42 m3 With outfeeding transport screw conveyor to the top of the silo building. Already dismountled, visit possible by appointment at our warehouse H-2013 Pomáz/Hungary.

Year of construction: 2023, condition: ready for operation (used), Two Vecoplan scraper chain conveyors are available. 1) VKU 800, year of construction: 2023, drive power: 5.5kW, belt speed: 24m/min, conveying capacity: approx. 120m³/h, belt width: 820mm, max. incline: 70°, section length: 10.2m. 2) VKU 1100, year of construction: 2023, drive power: 11kW, belt speed: 24m/min, conveying capacity: 180m³/h, belt width: 1150mm, max. incline: 70°, section length: 22mm. Documentation available. On-site inspection is possible. Gsdpfx Aaot Iw Rys Asir

Condition: new, sheet width 1020 mm plate thickness 2,5 mm distance between columns 1050 mm daylight opening mm 135 ° Gsdpfoupxf Uex Aa Aoir total power requirement Handbetrieben kW weight of the machine ca. 0,32 t dimensions of the machine ca. 1,4 x 0,6 x 1,3 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm.

Condition: ready for operation (used), Slab recovery line with below machines: One 2-blade board edger One single blade horisontal resaw Giodpfxsgwqk Sj Aa Ajr Conveyors system between the machines included.

Condition: refurbished (used), DIFFERENT TYPE OF MOTOR AND SLIDE for CELASCHI DET Gsdpfx Ajdvlcysa Aoir SECOND-HAND, FULLY RECONDITIONED

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Gisdjwp Rqfepfx Aa Aer Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, Söderhamns Rotary Debarker Cambio 85 - 66 - A Gedpfx Aaextc Afe Aoir Diameter: 10 - 66 cm Main motor: 30 kW

Year of construction: 2000, condition: used, Rotational speed: 227/min, power: 31kW, heating output: 7.8kW, length: 1952mm, width: 840mm, height: 1920mm, weight: 820kg. Gijdpfxjduyyzj Aa Aer

Condition: good (used), Year of construction: 2007, functionality: fully functional, Pellet production line based on Italian producer Zepi pellet press, hammer mill, pellet cooler and sifter. Machines are really powerful and reliable. Some parts like hammer mill are completely refurbished. Giedovx S Ryspfx Aa Ajr Year of production 2007.