Tool Room Milling Machine - Universal

DECKEL FP 1

Condition: good (used), Year of construction: 1992, functionality: fully functional, Technical details x-travel 300 mm y-travel 160 mm z-travel 290 mm table surface area 210 x 600 mm table load max. 200 kg tool taper SK 40 spindle turning speed range (16) 40 - 2000 U/min feeds -stepless- 5 - 500 mm/min rapid traverse 1,2 m/min spindle motor 1,5 / 1,9 kW total power requirement 9,5 kVA weight of the machine ca. 730 kg Guodpfxsxwui Se Ad Dei dimensions of the machine ca. 2000 x 2200 x 1655 mm Additional information The machine is in very good condition and comes from a research centre. Equipment: 3-axis active digital readout made by Heidenhain TNC 113 Fixed angle table Coolant equipment Kelch mounting block Machine vise Counterholding device for the horizontal spindle

Condition: good (used), Year of construction: 2005, operating hours: 84,564 h, functionality: fully functional, travel distance X-axis: 500 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, rapid traverse X-axis: 12 m/min, rapid traverse Y-axis: 12 m/min, rapid traverse Z-axis: 12 m/min, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, nominal power (apparent): 17 kVA, controller manufacturer: iTNC 530 Heidenhain, controller model: iTNC 530 Heidenhain, total height: 2,500 mm, total length: 3,000 mm, total width: 3,000 mm, table width: 500 mm, table length: 650 mm, table load: 200 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 10,000 rpm, operating hours of spindle: 22,855 h, spindle motor power: 13,000 W, number of slots in tool magazine: 16, tool length: 300 mm, tool diameter: 130 mm, tool weight: 6 g, Equipment: rotational speed infinitely variable, The machine is in good condition. A few things have been redone and freshened up. The following has been overhauled: -Complete X-axis bearing including ball screw and bearing -Various hydraulic components -Tool changer reset and sensors replaced -New door switch installed -New discs installed (unfortunately already got some flying chips again) -New coolant pump -New screen, as it was defective -New handwheel HR410 The machine does not have many spindle hours or switch-on hours. The machine has never seen a series production and has always been operated sensibly. Warm-up programs etc. We are tool and mold makers, so we tend to do more complex contours rather than heavy machining. I am only selling this because I need a simultaneous machine and also more travel paths. Technical data: Year of manufacture 2005 x-travel 500 mm y-travel 450 mm z-travel 400 mm Control iTNC 530 Heidenhain Main spindle Gujdjvtnm Hopfx Ad Dei Speed range - main spindle 20 - 10,000 rpm Drive power - main spindle 9 / 13 kW Torque 57 / 82 Nm Tool holder SK 40 Rotary table Table clamping area 630 x 500 mm Swivel range -5 / +110 ° Max. table load 200 kg T-slots 14 H7 T-slots - distance 63 mm C-axis +/- 360 ° Feeds: Rapid traverse (X / Y / Z) 12 m/min Feed rate 10,000 mm/min Tool changer: Tool positions 16 pos. Max. tool weight 6 kg Max. tool length 300 mm Max. tool diameter 80 mm Max. tool diameter with free adjacent box 130 mm Tool holder SK 40 Total power requirement 17 kVA Machine weight approx. 3.6 t Space requirement approx. 3.0 x 3.0 x 2.5 m Tool milling machine - Universal DECKEL MAHO - DMU 50 Attention: no chip conveyor and no automatic measuring probe! - 5 axes (3+2) - WITHOUT tools Attached are pictures of the machine. The machine was intentionally not cleaned before taking the pictures, so it is in the "chip" and is used daily. You can also see the hours of the machine there. Kinematics and geometry are OK. for our needs, but could possibly be re-measured. We have never had any crashes etc.

Condition: used, Year of construction: 1985, machine/vehicle number: 294, x-travel:400 mm y-travel:190 mm z-travel:310 mm table clamping surface:280 x 750 mm Reach of the vertical spindle:115-575 mm feed steps:16 feed range:11,2-355 mm/min tool taper:SK 40 speed steps :16 speeds::56-1800 min-1 Gsdpfx Adevcf Hpo Doui total power requirement:2,2 kW dimensions of the machine ca.:1550 x 1250 x 2000 mm weight of the machine ca.:1200 kg

Condition: good (used), Internal item no.: 25029 Universal milling machine Deckel FP1 Godpfx Adewvgcds Dsui 3-axis active digital readout (Heidenhain TNC113) Year of manufacture: 1987 Spindle taper: SK40 (S20x2) Travel: X 300 / Y 160 / Z 340 mm Speed: 40 - 2000 rpm (2 gearbox ranges) Infinitely variable feed. The machine is in a well-maintained condition and can be inspected under power on site. Including extensive accessories: - Operating manual / Electrical diagram / Spare parts list - Deckel drawer cabinet - SK40 tool holders (S20x2) - Counter-support - Coolant pump

Condition: excellent (used), functionality: fully functional, travel distance X-axis: 300 mm, travel distance Y-axis: 160 mm, travel distance Z-axis: 360 mm, For sale is a Deckel FP1 with 3-axis active control system The machine is fully functional and will be checked, cleaned and put into stock in our incoming goods department. Technical data: Digital display 3-axis active digital readout HEIDENHAIN X-axis travel 300 mm Y-axis travel 160 mm Z-axis travel 340 mm Tool holder: SK 40 Milling head type. Vertical milling head Speed range: 40 - 2000 mm/rev Number of steps: 16 Feed X-axis 290 mm Y-axis feed 150 mm Feed Z-axis 330 mm Machine weight 650 kg Machine dimensions 1200 x 1100 x 1800 mm Accessories - Active function in X-, Y- and Z-axis - Coolant device The offer refers only to the machine without tools, this can be negotiated additionally Gsder H E Uiopfx Ad Deui On request, loading and transport (Europe-wide) can be organized for an additional charge. Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: good (used), Year of construction: 1985, Deckel FP1 Aktiv with 3-axis Heidenhain digital readout, 3 active axes, rigid table, SK 40 M16 spindle taper. Central lubrication, operating manuals included. Good operational condition, comes from a vocational training center. Can be demonstrated under power by arrangement. Gjdpsxwunzsfx Ad Deui

Condition: reconditioned (used), Year of construction: 1994, Universal Tool Milling Machine DECKEL FP 1 With 3-axis active digital readout Heidenhain TNC 123 Year of manufacture: 1994 Travel: X 300 mm, Y 160 mm, Z 340 mm Spindle speed range: 40 – 2000 rpm Comes with the following accessories: Gjdpfx Adew Agxrs Djui Fixed angle table, 600 mm x 250 mm clamping surface Movable vertical milling head Extendable quill Infinitely variable feed via potentiometer 1 machine vice 1 tailstock with counter bearing 1 long milling arbor Ø 22 mm, Ø 16 mm, Ø 27 mm Various tool holders S 22 x 2 Z axis bellows 1 chip guard Machine lamp Automatic central lubrication pump Coolant system Operating manual THE MACHINE IS IN EXCELLENT CONDITION! THE MACHINE COMES FROM A TRAINING WORKSHOP!

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, Options: Chip conveyor Bar feeder interface Guodpfxjwifkmj Ad Doi Big bore chuck Memory extension 3-color lamp HP coolant

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, Universal milling machine Deckel FP1 with 3-axis active digital display TNC 113 Heidenhain and infinitely variable feed very good CONDITION Technical data: >> Year of construction 1990 Machine no. 2102-5046 >> Rigid angle table >> Speed: 40 - 2000 rpm >> Infinitely variable feed in 3 axes >> Rapid traverse in 3 axes >> Drive power .:1,5 / 1,9 KW >> Spindle brake >> Travel X/Y/Z: 300/160/340 mm >> Vertical milling head can be moved 100 mm on headstock >> Vertical quill and horizontal quill - SK40 >> Tightening system S20x2 >> Weight approx. 800 kg Gusdeu Um Eropfx Ad Dji Accessories and equipment: >> 3-axis digital readout Heidenhain TNC113 >> Electrical central lubrication >> Coolant device >> Operating instructions, spare parts plan Gojs3G About the machine : Universal milling machine Deckel FP1 built in 1990 in very good condition. The machine has very little crank play and all spindles can be moved easily. The milling machine runs very smoothly even at maximum speeds. On this newer FP1 model, the feed is infinitely variable in three axes, and the machine also has rapid traverse in these axes. A great advantage is the active 3-axis digital display. With this Heidenhain line control you can enter dimensions which the machine automatically approaches. The FP1 was in a training company where it was only used occasionally. An oil change was carried out. Mechanically and electrically tested. The Heidenhain digital display makes work easier and even more accurate. Take the opportunity to inspect and try out this little gem under power on site.

Condition: excellent (used), Year of construction: 1983, functionality: fully functional, Universal milling machine Deckel FP1 with 3-axis digital readout K&C New and 3-axis stepless feed Super CONDITION Technical data: >> Year of construction 1983 Machine no. 2102-2444 Gjdpfx Adotwlwzo Deui >> Rigid angle table >> Speed: 40 - 2000 rpm >> Infinitely variable feed in 3 axes >> Rapid traverse in 3 axes >> Drive power .:1,5 / 1,9 KW >> Spindle brake >> Travel X/Y/Z: 300/160/340 mm >> Vertical milling head can be moved 100 mm on headstock >> Vertical quill and horizontal quill - SK40 >> Tightening system S20x2 >> Weight approx. 800 kg Accessories and equipment: >> 3-axis digital indicator K+C Newly assembled with manufacturer's warranty and operating instructions. Display unit: Reference points, setting zero points, entering coordinates, mm/inch switching, absolute or incremental coordinates, circular functions, hole rows, radius milling functions, etc. >> Coolant device >> Operating instructions, spare parts plan To the machine : We are offering a Deckel FP1 universal milling machine built in 1983 in very good condition. The machine has very little crank play and all spindles can be moved easily. The milling machine runs very smoothly even at maximum speeds. On this newer FP1 model, the feed is infinitely variable in three axes, and the machine also has rapid traverse in these axes. The FP1 was in a training workshop where it was only used occasionally. An oil change was carried out. Mechanically and electrically tested. The new digital display from K&C makes work easier and even more precise. Take the opportunity to inspect and try out this little gem under power on site.

Condition: good (used), x-travel 300 mm y-travel 340 mm Gusdpfx Aeucphxed Doi z-travel 250 mm total power requirement 1,5 kW weight of the machine ca. 0,8 t Heidenh. 3 axes aktiv digital display Year of construction unknown

Condition: excellent (used), functionality: fully functional, Universal milling machine Deckel FP1 with 3 - axis digital readout Heidenhain original condition !!! Technical data: >> Machine no. 56560/08 Year of construction approx. 1975 >> Rigid angle table >> Speed: 40 - 2000 rpm >> Feed 2 axes >> Drive power .:1 / 1,5 KW >> Travel X/Y/Z: 300/150/340 mm >> Vertical quill SK40 and horizontal quill - SK40 >> S20x2 tightening system >> Weight approx. 700 kg Ecvf9Jfv9 Accessories and equipment: >> 3-axis digital display Heidenhain >> Coolant device About the machine : We offer a universal milling machine Deckel FP1 in very good original condition. The Deckel has very little crank play and all spindles can be moved easily. An oil change has been carried out. Mechanically and electrically tested. The Heidenhain digital display makes work easier and even more precise. Take the opportunity to inspect and try out the lids on site under power. Gujdpfx Aou Nvxmsd Dji

Condition: excellent (used), Year of construction: 1978, functionality: fully functional, Universal milling machine Deckel FP1 with 3-axis digital display K&C infinitely variable feed in light gray Super condition Technical data: >> Year of construction 1978 Machine no. 2101-0465 >> Rigid angle table >> Speed: 40 - 2000 rpm >> Feed stepless 2 axes >> Drive power .:1,5 / 1,9 KW >> Spindle brake >> Rapid traverse >> Travel X/Y/Z: 300/160/340 mm >> Vertical milling head can be moved 100 mm on headstock >> Vertical quill and horizontal quill - SK40 >> Tightening system S20x2 >> Weight approx. 700 kg Accessories and equipment: >> 3-axis digital indicator K&C Newly assembled with manufacturer's warranty and operating instructions. Display unit: Reference points, setting zero points, entering coordinates, mm/inch switching, absolute or incremental coordinates, circular functions, hole rows, radius milling functions, etc. >> Coolant device To the machine : We are offering a Deckel FP1 universal milling machine in very good condition. The machine has very little crank play and all spindles can be moved easily. The bellows are all new. On this newer FP1 model, the feed is infinitely variable in two axes and the machine also has a rapid traverse. An oil change has been carried out. Mechanically and electrically tested. The new digital display from K&C makes work easier and even more precise. Take the opportunity to inspect and try out this machine on site under power. Guedpfx Adot Aav Ie Dsi

Condition: new, Technical data: Drilling capacity in steel: 50 mm Tapping capacity: M33 face milling cutter: 100 mm end mill: 25 mm spindle: MK 4 throat depth: 340 mm Speeds: (6) 50 - 1510 1/min quill stroke: 200 mm Gsdpfx Aspxmlqjd Djui quill feed: 0,1 / 0,2 / 0,3 / 0,4 mm/rev table size: 820 x 240 mm traverse path X: 460 mm traverse path Y: 280 mm column diameter: 180 mm Number of T-slots: 4 T-slot size: 16 x 26 mm motor power: 3 kW Weight, approx.: 750 kg Equipment: - Cross table - thread tightening spindle - Thread cutting device - Automatic spindle feed - LED machine light - Rotatable table - Manual fine feed - Coolant device - Height adjustable protective cover - Limit switch protected spindle

Condition: excellent (used), Year of construction: 1985, functionality: fully functional, Universal milling machine Deckel FP1 with 3-axis digital readout K&C New and 3-axis stepless feed Super CONDITION Guedpfxst Aarpe Ad Dei Technical data: >> Year of construction 1985 Machine no. 2102-2867 >> Turn-tilt-swivel table (newly planed) >> Speed: 40 - 2000 rpm >> feed stepless in 3 axes >> Rapid traverse in 3 axes >> Drive power .:1,5 / 1,9 KW >> Spindle brake >> Travel X/Y/Z: 300/160/340 mm >> Vertical milling head can be moved 100 mm on headstock >> Vertical quill and horizontal quill - SK40 >> Tightening system M16 >> Weight approx. 800 kg Accessories and equipment: >> 3-axis digital indicator K+C Newly assembled with manufacturer's warranty and operating instructions. Display unit: Reference points, setting zero points, entering coordinates, mm/inch switching, absolute or incremental coordinates, circular functions, hole rows, radius milling functions, etc. >> Coolant device >> Operating instructions, spare parts plan To the machine : We are offering a Deckel FP1 universal milling machine built in 1985 in very good condition. The machine has very little crank play and all spindles can be moved easily. The milling machine runs very smoothly even at maximum speeds. On this newer FP1 model, the feed is infinitely variable in three axes, and the machine also has rapid traverse in these axes. An oil change has been carried out. Mechanically and electrically tested. The new digital display from K&C makes work easier and even more precise. Take the opportunity to inspect and try out this machine under power on site.