Four rolls Bending roll 3000 x 70 mm

FACCIN 4HEP 3163

Condition: good (used), Year of construction: 2016, spindle speed (max.): 3,500 rpm, overall weight: 6,000 kg, Equipment: documentation/manual, rotational speed infinitely variable, Main parameters: Hfjdpfx Aswtg Inoftsn Controller: FANUC 0iD/31iA Chuck.: SAMCHULLY 10" Spindle bore: 86mm With jacket tube.:78mm Turret head: 12 main positions 12 secondary positions, BMT65 connection, Programmable hydraulic tailstock: MT5 Main spindle power: 22kW S1max=3500 1/min Living tool power: 5.5kw S2max=5000 1/min X movement range: 260mm Z axis movement range: 830mm Y axis movement range: + - 52mm (104mm) C axis Maximum turning length: L=760 Largest turning diameter: D=376mm Fast travel speed: 30m/min Automatic tool measurement with probe arm Weight: 6000 kg

Condition: good (used), Year of construction: 2000, control type: NC control, controller manufacturer: Davi Smart, number of rollers: 4, roller (bottom) diameter: 340 mm, roller (top) diameter: 370 mm, side roll diameter: 320 mm, roller length: 3,100 mm, sheet thickness (max.): 25 mm, overall weight: 18,500 kg, total length: 5,900 mm, total width: 2,200 mm, total height: 2,300 mm, power: 30 kW (40.79 HP), Equipment: cone bending device, 4 roll plate bender Davi Promau - MCB-3037 MACH-ID 9751 Make: Davi Promau Type: MCB-3037 Control: Davi Smart Year: 2000 Conical bending attachment Extended roll end for section bending jobs Digital read out position side rolls Central lubrication CE-Declaration Rolling width: 3100mm Rolling thickness 3x toproll Ø:20mm Rolling thickness 5x toproll Ø:25mm Rolling thickness prebending: 22mm Top Roll Ø: 370mm Bottom Roll Ø: 340mm Side roll Ø: 320mm Number of rolls: 4 Rolling speed: 0-5 Adjustiment lower roll: 0-200mm/min. Hfjdpfszi Ra Rex Afton Adjustment side rolls: 0-200mm/min. Number of driven rolls: 2 Power: 30kW Length: 5900mm Width: 2200mm Height: 2300mm Weight: 18500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), functionality: fully functional, Year of construction: 1999, machine/vehicle number: TH241-14/433886, operating hours: 131 h, ABUS ELV crane system crane runway bridge crane indoor crane crane Load capacity / lifting capacity: 5t - 5000 kg Gauge: 13,500 mm, overall width approx. 13,700 mm Year built: 1999, with floor control Lifting height: 6 m Overall height from crane top edge to hook approx. 1,020 mm (Girder: 540 mm + lifting gear: 480 mm) End carriage length with buffers approx. 270 cm Hfsdjx Ev Tkepfx Afton SWP: Full load hours used: 131, theoretical remaining service life: 1,469 hours Crane is dismantled and immediately available Very good condition, inspection book is available Column-mounted slewing cranes and wall-mounted slewing cranes also available Demag KBK and Abus HB systems, as well as Errikla, Hadef, Stahl KT 2000, etc. Shipment by freight forwarding possible, please inquire with postal code Collection preferred

Year of construction: 1997, condition: ready for operation (used), Travel X/Y/Z: 1300mm/1100mm/1000mm, table dimensions X/Y: 800mm/800mm, number of pallets: 14, max. table load: 2200kg, table indexing: 0.001°. Speed: 7000rpm, spindle power: 50hp, tool magazine: 80, dimensions X/Y/Z: approx. 7000mm/3400mm/3800mm, weight: approx. 24000kg. On-site inspection is possible. Hedpfx Afotx Dn Uetefn

Condition: excellent (used), functionality: fully functional, coil weight: 8 kg, sheet thickness (max.): 3 mm, sheet thickness steel (max.): 3 mm, total width: 1,250 mm, Slitting line for sale Hjdev Twi Rspfx Aftofn

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, New machine, immediately available, 12 months warranty -Internal dimensions (w x d x h): 1250 x 4000 x 1450 mm -External dimensions (w x d x h): 1900 x 4900 x 2500 mm -Power consumption: 240 kW -Current consumption: 350 Amperes -Maximum temperature: 1300 °C -Oven weight (approx.): 6000 kg -Control system: JUMO IMAGO 500 -Software packages: (OPCA & PCC) -Display unit: JUMO Logoscreen 601 -Includes: feedthrough hole and 6 additional slots for recording type K customer thermocouples -Multi-zone design (3 zones) Hedpfxsy Avmlo Aftofn -Switchgear with solid-state relays -Climate control for the switchgear -Automatic inlet and outlet dampers -Controlled cooling system (including frequency converter, controlled via the control system) -Electrically driven furnace car -Maximum load: 3.5 tons -Swinging door -Documentation, CE declaration We would be happy to offer installation, commissioning, and training for your employees. Please contact us! We stock new and used industrial furnaces. Inspections in our warehouse are possible upon request. Furnace car oven, car hearth oven, furnaces, annealing furnace, firing furnace, hardening furnace, heat treatment furnace, oven, stress-relieving furnace, enamelling furnace, drying oven, industrial furnace, bogie hearth furnace, car hearth furnace, shuttle kiln, bogie hearth kiln

Condition: used, Year of construction: 2008, functionality: fully functional, travel distance X-axis: 2,050 mm, travel distance Y-axis: 850 mm, travel distance Z-axis: 800 mm, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 12 m/min, feed rate X-axis: 8 m/min, feed rate Y-axis: 8 m/min, feed rate Z-axis: 8 m/min, table width: 850 mm, table length: 2,200 mm, table load: 4,800 kg, spindle speed (min.): 10,000 rpm, distance table to spindle center: 950 mm, Equipment: chip conveyor, documentation/manual, Johnford VMC 2000 vertical machining center, CNC Heidenhain iTNC 530. X-axis – Longitudinal 2,050 mm Y-axis – Transverse 850 mm Z-axis – Vertical 800 mm Spindle-to-table distance 150-950 mm Main spindle to column distance 885 mm Table Surface 2,200x850 mm Maximum weight 4,800 kg Hfodsxdiigopfx Aften Spindle Head Spindle taper - BT-40 (BIG PLUS System) Speed range (2) 10,000 rpm Motor HP 25 Equipped with: - Internal coolant system 20 bar - Part probe - Tool probe - Rigid tapping - Electronic handwheel - 2 longitudinal chip conveyors - Separate tank with filtration unit - Full enclosure

Condition: excellent (used), Year of construction: 2008, operating hours: 82,500 h, functionality: fully functional, travel distance X-axis: 5,000 mm, travel distance Y-axis: 3,000 mm, travel distance Z-axis: 1,750 mm, feed rate X-axis: 65 m/min, feed rate Y-axis: 65 m/min, feed rate Z-axis: 65 m/min, spindle speed (max.): 20,000 rpm, rapid traverse X-axis: 65 m/min, rapid traverse Y-axis: 65 m/min, rapid traverse Z-axis: 65 m/min, torque: 63 Nm, overall weight: 90,000 kg, Equipment: rotational speed infinitely variable, First commissioning: 2008 Control system: Heidenhain iTNC 530 incl. handwheel HR420 X-axis: approx. 5,000 mm Y-axis: approx. 3,000 mm Z-axis: approx. 1,750 mm A-axis: -120 / +95° C-axis: ± 360° Maximum workpiece size 3,800 mm (X-direction) 1,800 mm (Y-direction) 1,150 mm (Z-direction) Can be machined in 5 axes (90° free A-axis) in a single setup using a 300 mm long tool. Machine operating hours: approx. 83,000 h Total spindle hours: approx. 37,000 h Machine bed (can be installed flush or above ground!) Dimensions: 5,000 x 2,250 x 300 mm - manufactured from EN-GJL-250 9 T-slots according to DIN 650-28H12 with a spacing of 250 mm and 125 mm from the edge 2-axis milling head, inspected by the manufacturer! Spindle power: 20 kW Spindle speed: max. 20,000 min-1 Torque: max. 63 Nm Tool holder: HSK 63A Tool clamping: hydraulic Holding torque (clamped) A & C axis: 2,000 Nm Drive system for linear axes Feed rate X, Y, and Z axes: up to 65 m/min Axis acceleration X, Y, and Z axes: up to 5 m/s2 Connection data Voltage: 400 V Frequency: 50 Hz Power consumption: 130 kW Dimensions, weights Machine footprint without peripherals: approx. 7,500 x 8,500 x 6,600 mm Total weight: approx. 90,000 kg Color Enclosure, portal, control cabinet: RAL 7035 light gray Milling head and applications: RAL color 5002 aquamarine blue Additional equipment - Minimum quantity lubrication - 50-position tool changer - Work area cover Condition of the machine The milling head has been freshly inspected by the machine manufacturer, thus partially overhauled and fully functional. Completely new machine bed from Stolle! The additional modules shown on the machine bed are not included in the scope of delivery. The extraction systems and ducts shown are also not included in the scope of delivery. The previous owner was an established Formula 1 team from Central Europe. The machine was always under a maintenance contract with the manufacturer. Hfjdpfx Afezkuirjtsn Currently, the machine is disassembled and stored. However, an inspection is still possible at any time by arrangement.

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Hfedpfx Aeuz If Neftsn Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Year of construction: 1973, functionality: unexamined, Vertical Turret Lathe - Double Column | Brand: TITAN | Type: SC 2500 Year of manufacture: 1973; modernization in 2011 to Siemens SINUMERIK 840D sl control system The machine is a ‘TITAN’ model, i.e. from a Romanian manufacturer. However, the design is licensed from SCHIESS in Düsseldorf and is therefore comparable to the well-known SCHIESS machines from that period. The machine was professionally disassembled by technicians from the machine manufacturer SCHIESS, properly preserved and placed in storage by the owner. TECHNICAL SPECIFICATIONS / EQUIPMENT: - Faceplate diameter: 2.500 mm - Swing diameter: 2.600 mm - Max. workpiece weight: 12 tons - Turning height: 1.600 mm - Number of turning supports / RAMs: 2 * Ram dimensions: 250 x 210 mm each - Main drive: 55 kW EQUIPMENT: - CNC control: Siemens SINUMERIK 840D sl - Tool turret (right) - Chip conveyor Dimensions / Weight: - Installation area: 5.600 x 4.800 mm - Hall space inc. operating and service areas: approx. 7.000 x 7.000 mm - Machine height: 6.200 mm - Machine weight: approx. 45 tons Hfsdjzlb H Tspfx Afton There is no guarantee for correctness and completeness of the technical details and accessories. - Subject to prior sale -