Used Roll benders (motor-driven) for sheet thickness over 14mm for sale (116)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Hodpfx Afoh U Rzgotjnu Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: used, Year of construction: 2007, Bending length 3050 mm Max. prebending capacity 13 mm Max. rolling capacity 16 mm Top roll dia. 340 mm Lower roll dia. 340 mm Side rolls dia. 240 mm 4-rolls Hjdsxhgqiepfx Aftsnu Fully hydraulic Hydraulic drop end Digital read out of roll positions Equipped with: Top support Side support

Condition: good (used), Year of construction: 2001, Bending length: 4000 mm Bending strength: 45 mm Anbiegung (kalt) / Pre-bending (cold): 38 mm Antriebsleistung / Drive power: 100 kW Anzahl Walzen / Number of rollers: 4 Adjustable rollers / Adjustable rollers: 3 Verstellungsart der Walzen / Adjustment type of rolls: hydraulisch Oberwalzendurchmesser / Top roll diameter: 710 mm Unterwalzendurchmesser / Bottom roll diameter: 640 mm Seitdwalzendurchmesser / Side roll diameter: 520 mm Arbeitsgeschwindigkeit / Working speed: 2+4 m/min (up to 8m/min) Gewicht Maschine (mit Walze) / Weight of machine (with roller): 78 t Hjdpexnk Sqjfx Aftsnu Zusatzausrüstung / Additional equipment: Elektronischer Gleichlauf / Electronic synchronization Luftgekühlter Öl-Kühler / Air-cooled oil cooler Obere Stützvorrichtung / Upper support device Seitliche Zylinderabstützvorrichtung (10t) / Lateral cylinder support device (10t) Infeed table (20t) / Infeed table (20t) hydr. Bladder accumulator / hydr. bladder accumulator Konusbiegenvorrichtung / Cone bending device

Condition: new, sheet thickness: 45bending length: 2600upper roll diameter: 460 Technical specifications: - Hardened and polished rolls - Complete body made of ST-52 Steel - Machine have 4 rolls and designed for symmetrical working principle - Hydraulic powered cover for easy material extracting - Digital readout for side rolls (2 digital readout) - Side rolls are free for rotation and upwards downwards movements are hydraulic powered - Top and bottom rolls are driven by hydraulic and gearbox. Bottom roll’s vertical movements are hydraulic powered - Separate control panel form machine - Conic bending device - In accordance for CE norms Options: - variable speed of rotation EURO 5.858,-- - metarial feeding table EURO 5.100,-- - oil coiler STD. - center support EURO 18.750,-- - side supports EURO 12.500,-- - Automatic material extractor - PLC control - CNC control Hnjdpfx Afod Ab Rhoteu - Automatic material loading system - Changeable top roll - Adjustable bottom roll support system (for customer’s special requests) We have many references!

Year of construction: 1980, condition: good (used), with initial rounding Technische Daten:/ technical details Biegelänge / bending lenght 2000 mm max. Blechstärke / max. sheet thickness 20 mm Anbiegeleistung / initial rounding 15/11 mm Walzendurchmesser Unterwalzen / roll diameter below rolls 280 mm Oberwalzendurchmesser / diameter of the upper roll 300 mm Antriebsleistung Hauptantrieb / drive capacity main drive 16,2 kW Antriebsleistung Anstellantrieb Oberwalze / drive capacity upper roll 4,8 kW Antriebsleistung Anstellsntrien Unterwalze / drive capacity below roll 3,7 kW Gewicht ca. / weight ca. 14200 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. Hodpfekzg E Aox Aftjnu

Condition: good (used), Year of construction: 2019, roller (top) diameter: 390 mm, working width: 2,500 mm, sheet thickness steel (max.): 28 mm, working length: 2,500 mm, Top support 3000 height  Side support with in feed fingers 3 ton Roller conveyor 7500 x 2500 mm PGS-Ultra CNC Control Fully hydraulic machine Central lubrication Rolling width: 2500mm Rolling thickness 3x toproll Ø:24mm Rolling thickness 5x toproll Ø:28mm Rolling thickness prebending: 24mm Top Roll Ø: 390mm Bottom Roll Ø: 370mm Side roll Ø: 295mm Number of rolls: 4 Rolling speed: 0 - 5 Hjdpfx Afov Tbcbetsnu Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 200mm/min. Control: SIEMENS PGS Classic TOUCH Top support: Yes Side supports: Yes Number of driven rolls: Yes Power: 30kW Length: 6200mm Width: 2200mm Height: 3800mm Weight: 18000kg

Condition: good (used), functionality: fully functional, Year of construction: 1978, machine/vehicle number: 4303, working width: 3000 mm metal sheet thickness: 15 mm metal sheet thickness when bending: 10 mm upper roller-Ø: 320 mm Hnsdpod D Nxxofx Afteu below roller-Ø: 310 mm working speed: ca. 5,5 m/min electrical connection: 380 V kW weight: ca. 17000 kg space needed: 5450 x 2100 x 2450 mm

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 460 mm, roller (top) diameter: 460 mm, side roll diameter: 380 mm, working width: 2,050 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 50 mm, power: 38.5 kW (52.35 HP), warranty duration: 12 months, STANDARD EQUIPMENT * The lower, upper and side rolls move up and down linearly via hydraulic cylinders attached to the body * Protected against overload * The upper roll and side rolls are driven by hydromotor and planetary gearbox (all 3 rolls are motor driven) * Three digital displays allow easy reading of roll positions * Hydraulic opening head and automatic lifting shaft enable easy removal of the bent workpiece * Easy operation with mobile control panel * Welded steel construction body * SAE 1050 (CK 50) induction hardened, forged or rolled steel shafts * Conical bending system * Centralized lubrication system * Hydraulic synchronization system for parallel movement of shafts (Ø280 -320 -350 -380 -400 -460) * Electronic synchronization system (Ø500-550-580-620-680) * Dual-speed operation system OPTIONAL EQUIPMENT * Automation with NC and CNC control * Top crane (elevator) for support in large diameter bending * Hydraulic side supports for large diameter bending * Hydraulic sheet removal system * Ground and polished rolls for special applications * Infinitely variable speed adjustment system * Electronic synchronization system for parallel movement of shafts (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length: 2050 mm Hedjxd S T Ujpfx Aftsnu Pre-bending: 35 / 40 mm Bending: 40 / 50 mm Upper & Lower Roll Diameter: 460 mm Side Roll Diameter: 380 mm Motor Power: 38.5 kW Bending Speed: 1.5 - 5 m/min Length: 4850 mm Width: 2300 mm Height: 2350 mm Weight: 19,800 kg

Year of construction: 1985, condition: used, machine/vehicle number: 112-176, Technical data: -Bending mot. Automatic or manual mode -Bending performance square steel ST 37 up to approx. 25 mm -Bending performance flat iron ST 37 to approximately 30 x 8 mm -Bending length betw. the rotating units adjustable up to approx. 1000 mm -Faceplate with various recording profile perforations -Tailstock / recovery storage -Delay start bending / bending length twisting preselection - right - left rotation -Space requirement approx. B 1750 x H 1100 X 500 mm -Drive 400 V / 0,75 kW -Weight approx. 150 kg Hjdpfx Aoc I Snzjftjnu

Condition: new, bending length: 2600sheet thickness: 16upper roll diameter: 300 Technical specifications: - Hardened and polished rolls - Conic bending device - Digital readout for side rolls - Complete body made of ST-52 Steel - Portable control panel separated form machine - Rolls are mounted with bearings Hedpfjd Ab S Usx Aftenu - Top roll cover, openable and closeable by hydraulic, controlled from control panel. - All rolls are driven by hydraulic motor and planetary gearbox - Side rolls upwards downwards movements are hydraulic powered Options: - variable rotation speed EURO 4.682.00 Material feed table on request Oil cooler EURO 1,040.00 Center support EURO 13.600,00 Side supports EURO 8.250.00 We have many references!

Condition: ready for operation (used), functionality: fully functional, number of rollers: 3, working width: 2,500 mm, sheet thickness steel (max.): 8 mm, Used Roundo plate rolling machine 2500x8MM, 3 rolls, fully functional Hnodpfxsxcgrvj Aftju

Condition: good (used), Year of construction: 2017, Sahinler 4R HSS 20-280 Hydraulic 4-roll plate bending machine – Year 2017. Bending length 2050 mm Max. bending capacity - mild steel 20. Upper roll diameter 280 mm Lower roll diameter 280 mm Lateral roll diameter 220 mm Bending speed 1,5 / 5 m/min. Motor power 16 kW Hnsdpfjxau D Ijx Afteu

Condition: new, functionality: fully functional, Year of construction: 2025, FACCIN 4HEP S54 Four roll bending machine Electronically controlled, electric drive, four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rolls: planetary guide Hnodpfxeiivgrs Aftju Working length: 3000 mm Top roll diameter: 300 mm lower roll diameter: 280 mm Side rolls diameter: 200 mm Guaranteed installed power: 10.8 kW Guaranteed maximum rolling speed: 5 m/min Guaranteed machine weight: 10,000 kg Length: 5,500mm Width: 1,400mm Height: 1,600mm Guaranteed services: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 18 mm Bending performance (full working width) 12 mm from pipe diameter 1500 mm Rolling capacity (full working width) 12 mm Bending capacity (full working width) 10 mm from pipe diameter 450 mm Standard equipment: Electrical drive of the top roll Planetary movement of the side rolls Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rollers for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 280 mm, roller (top) diameter: 280 mm, side roll diameter: 220 mm, working width: 2,050 mm, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, power: 16.5 kW (22.43 HP), warranty duration: 12 months, STANDARD EQUIPMENT * The top, lower, and side rolls move vertically via pistons hydraulically connected to the body. * Protected against overload. * The top and side rolls are driven by hydromotors and planetary gearboxes (all 3 rolls are motor-driven). * The positions of the rolls can be easily read from three digital displays. * The hydraulically opening head and the automatically rising shaft allow easy removal of the bent workpiece. * User-friendly operation with mobile control panel. * Welded steel construction body. * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts. * Conical bending system. * Centralized lubrication system. * Hydraulic synchronization system for parallel movement of the rolls (Ø280 -320 -350 -380 -400 -460). * Electronic synchronization system (Ø500-550-580-620 -680). * Dual speed operation system. OPTIONAL EQUIPMENT * Automation with NC and CNC control. * Top crane (elevator) for support during large diameter bending. * Hydraulic side supports for large diameter bending. * Hydraulic sheet ejection system. * Ground and polished rolls for special applications. * Stepless speed regulation system. * Electronic synchronization system for parallel movement of the rolls (Ø280 -320 -350 -380 -400 -460). TECHNICAL SPECIFICATIONS Bending Length: 2050 mm Pre-Bending: 12/16 mm Bending: 16/20 mm Top & Bottom Roll: 280 mm Side Roll: 220 mm Motor Power: 16.5 kW Bending Speed: 1.5 - 5 m/min Length: 4350 mm Width: 1700 mm Height: 1850 mm Weight: 8550 kg Hnjdjxd S Npspfx Aftsu

Condition: new, functionality: fully functional, Year of construction: 2025, max rolling capacity (cold): mm. 32 Hnsdpfof T Rzfex Afteu max prebending capacity (cold): mm. 24 at diameter mm. 2050 with material yield strength N/mm2 260 working length: mm. 3050 number of rolls: four top roll diameter mm. 410 pinching roll diameter mm. 390 driven rolls : two rotation speed 5 m./min. rolls rotation: hydraulic installed power: 30 PS Voltage 400V, 50Hz, 3Ph Inkl.: - hardened & polished rolls - cone bending device - electronic rolls parallelism - Siemens PLC Control - CE certificate - control console on wheels

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 250 mm, roller (top) diameter: 250 mm, side roll diameter: 200 mm, working width: 1,550 mm, sheet thickness (max.): 15 mm, sheet thickness steel (max.): 15 mm, STANDARD EQUIPMENT Highly suitable for bending light and medium sheet metal, aluminum or stainless steel materials Ideal for bending materials into round and various diameters Bottom roll and side rolls move directly up and down hydraulically via linear movement Protected against overloading Top roll is driven by an electric motor and planetary gearbox. Bottom roll driven by cardan coupling system. Two rolls are drive rolls Roll positions can be easily read from three digital displays Hydraulically operated openable head allows easy removal of the bent workpiece Very easy to use with movable control panel Welded steel construction body SAE 1050 (CK 45) induction hardened forged or rolled steel shafts Conical bending system Hydraulic balancing system for parallel movement of the rolls Complies with EU safety standards and CE marked Operation manual OPTIONAL EQUIPMENT Remote assistance with NC control Overhead crane (hoist) for supporting large diameter bending Hydraulic side supports for assisting with large diameter bending Ground and polished rolls Dual-speed adjustment system Stepless speed regulation Return rotation driven by hydromotor Ejector system TECHNICAL SPECIFICATIONS Bending Length: 1550 mm Pre-Bending: 10/12 mm Bending Thickness: 12/15 mm Top & Bottom Roll Diameter: 250 mm Side Roll Diameter: 200 mm Min. Bending Diameter: 375 / 1250 mm Hnjdpfx Aexd S Aiefteu Motor Power: 7.5 + 1.5 kW Bending Speed: 5 m/min Tank Capacity: 40 L Length: 3500 mm Width: 1500 mm Height: 1370 mm Weight: 4650 kg

Condition: new, functionality: fully functional, Year of construction: 2025, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Hjdpfx Aet Akt Rjftsnu Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 3, roller (bottom) diameter: 250 mm, roller (top) diameter: 250 mm, side roll diameter: 200 mm, roller length: 1,550 mm, working width: 1,550 mm, sheet thickness (max.): 15 mm, sheet thickness steel (max.): 15 mm, power: 7.5 kW (10.20 HP), warranty duration: 12 months, STANDARD EQUIPMENT * Side rolls move up and down orbitally via hydraulic pistons * Protected against overloading * All rolls are driven by hydromotors and planetary gearboxes * Easily removable bent parts thanks to a hydraulically opening top roll Hjdpfx Aoxbzr Usftjnu * Very easy operation with movable control panel * Lower roll positions are easily read via two digital displays * Welded steel frame construction * SAE 1050 (CK 45) induction-hardened, hot-rolled steel shafts * Conical rolling system with roller bearings * Hydraulic synchronisation system for parallel movement of shafts * Extended shaft ends to allow mounting profile and pipe bending rolls OPTIONAL EQUIPMENT * Top crane (elevator) for large diameter bending support * Hydraulic side supports for large diameter bending * Specially ground and polished rolls for custom work * Bending rolls for profiles * Infinitely variable hydraulic speed adjustment * Electronic synchronisation system for parallel movement of shafts TECHNICAL SPECIFICATIONS Bending Length: 1550 mm Pre-bending: 10/12 mm Bending: 12/15 mm Top & Bottom Roll Diameter: 250 mm Side Roll Diameter: 200 mm Motor Power: 7.5 kW Bending Speed: 5 m/min Length: 3500 mm Width: 1200 mm Height: 1370 mm Weight: 3600 kg

Condition: new, functionality: fully functional, Year of construction: 2025, HAV 3293 Plate width: 3200mm Top Roll diameter: 930mm Side rolls diameter: mm 800 Machine weight: 150 Ton Rolling capacities (Y:260Mpa/Ø 4650mm): 3200mmx155mm Prebending capacities (Y:260Mpa/Ø 4650mm): 3200mmx115mm Hjdpfoiivg Ssx Aftjnu

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 550 mm, roller (top) diameter: 550 mm, side roll diameter: 450 mm, roller length: 3,100 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 50 mm, power: 70 kW (95.17 HP), warranty duration: 12 months, Equipment: emergency stop, foot remote control, hardened rollers, swiveling upper roller, STANDARD EQUIPMENT * The bottom and side rolls move up and down linearly via hydraulic pistons attached to the frame * Protected against overloading * The top and side rolls are driven by hydromotors and planetary gearboxes (all 3 rolls are motor-driven) * Easy roll position reading via three digital indicators * Easy removal of bent parts thanks to hydraulically opening head and automatically lifting shaft * Very user-friendly operation with the mobile control panel * Welded steel construction frame * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Cone bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of rolls (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620-680) * Dual-speed operation system OPTIONAL EQUIPMENT * NC and CNC control for automation * Top crane (elevator) for support when bending large diameters * Hydraulic side supports for large diameter bending * Hydraulic sheet ejector system Hodexbzptspfx Aftjnu * Polished and ground rolls for special applications * Infinitely variable speed adjustment system * Electronic balancing system for parallel roll movement (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length : 3100 mm Pre-bending : 50/40 mm Bending : 40/35 mm Top & Bottom Roll : 550 mm Side Roll : 450 mm Motor Power : 70 kW Bending Speed : 1 - 4 m/min Length : 6750 mm Width : 2900 mm Height : 2950 mm Weight : 47,000 kg

Condition: new, functionality: fully functional, Year of construction: 2025, TECHNICAL SPECIFICATIONS: Number of rolls FOUR Geometry linear guides Maximum plate width mm 3000 Hodpfx Afsgd T R Dstenu Top roll diameter mm 390 Bottom roll diameter mm 370 Side rolls diameter mm 295 Installed power HP 40 Stepless variable rotation movement m/1' 4-8 Machine weight (guaranteed) Kg 19,000 Guaranteed performance with material yield point 260 N/mm² Rolling capacity (full working width) Ø 1950 mm 25 mm Bending performance (full working width) Ø 1950 mm 20 mm Rolling capacity (full working width) Ø 507 mm 18 mm Bending performance (full working width) Ø 507 mm 16 mm • Hardened and polished rollers • Siemens NC control • Cone bending device with electronic tilting

Condition: new, functionality: fully functional, Year of construction: 2025, FACCIN 4HEP 3135 Four roll bending machine Electronically controlled, hydraulic four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rolls: planetary guide Working length: 3000 mm Top roll diameter: 350 mm Lower roll diameter: 330 mm Side rolls diameter: 250 mm Guaranteed installed power: 14.4 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 13,000 kg Length: 5,700mm Width: 1,800mm Height: 2,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 20 mm Bending performance (full working width) 15 mm from pipe diameter 1750 mm Hjdoiivc Dspfx Aftjnu Rolling capacity (full working width) 14mm Bending capacity (full working width) 12mm from pipe diameter 455 mm Standard equipment: planetary movement of the side rollers Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2025, FACCIN 4HEP 3163 Four roll bending machine Electronically controlled, hydraulic four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rollers: planetary guide Working length: 3000 mm Top roll diameter: 630 mm Lower roll diameter: 570 mm Side rolls diameter: 500 mm Guaranteed installed power: 72 kW Guaranteed maximum rotation speed: 5 m/min Hsdpoiivfqsfx Aftjnu Guaranteed machine weight: 58,000 kg Length: 6,800mm Width: 3,600mm Height: 3,550mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 70 mm Bending performance (full working width) 60 mm from pipe diameter 3150 mm Rolling capacity (full working width) 55 mm Bending capacity (full working width) 50 mm from pipe diameter 820 mm Standard equipment: Planetary movement of the side rolls Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2025, FACCIN HAV 3162 variable three-rolls bending machine Electronically controlled, hydraulic three-rolls bending machine Hnedsiivgyepfx Aftou Technical specifications: Number of Rolls: Three Geometry of the side rolls: variable Working length: 3050 mm Top roll diameter: 620 mm Side rolls diameter: 550 mm Pressure force against the top roll: 630 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 55 kW (75 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 45,000 kg Length: 7,600mm Width: 3,700mm Height: 3,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 75 mm Bending performance (full working width) 48 mm from a pipe diameter of 3,100 mm Rolling capacity (full working width) 55 mm Bending performance (full working width) 40 mm from pipe diameter 805 mm Standard equipment: variable geometry with linear guides for rolls movement Extra long release arm for increased frame stability Electronic parallelism system EPS Hardened rolls for high wear protection All rolls ground after heat treatment Siemens S7-HMI PLC control PGS-CLASSIC control with Siemens touch panel Hitech hydraulic and electric package Simultaneous rotation and rolls movement Safety trip wire with emergency stop and CE certification central lubrication Water cooling for the hydraulics cone bending device Prepared for retrofitting supports and roller conveyors FACCIN Advantage Package AP

Condition: new, functionality: fully functional, Year of construction: 2025, Three rolls variable axis bending roll Make FACCIN, model HAV/S 3145 Technical specifications: Hnedpfx Afjc S N Nqjtju Number of Reels: Three Geometry of the side rollers: variable Working width: 3000 mm Top roller diameter: 450 mm variable three-roller bending machine