FASI EV6 - Single Hopper Loader

FASI EV6

Condition: new, *Technical standard specification: Heating capacity: 9 kW Cooling capacity: 50 kW medium: water up to 160°C Max. external volume: 16 ltr at 160°C max. Flow rate 57l/min  max. Delivery pressure 6,0 bar Dimension L x W x H 780 x 305 x 705 mm Weight approx. 80 kg HIGHLIGHTS EQUIPMENT: - Smart Controller Plus 7" touch / 4.0 capable - Flow measurement, adjustable flow alarms - Return temperature display - Frequency converter for pump speed control with automatic mode for energy-optimised operation, or adjustable flow rate (in the operating range of the temperature control system) Iodpoftm Hrsfx Angobb - Electronic pressure transducer in the flow - Interface via 9-pin D-Sub connector 20mA/TTY - Connection for external temperature sensor PT 100 for measuring and displaying the mould temperature - Continuous bypass of the heat exchanger with a 3-way valve to reduce deposits in the heat exchangers - More powerful pump, hydraulic parts made of VA, magnetically coupled - Tool emptying by suction - Booster pump for tool filling at high temperatures - Filling via cooling water can be switched to separate filling - SSR for heating control - IP54 splash water protection Visit our website for more details or for other performance classes. *This unit is compliant with European Directives. Other directives and standards are only complied with if stated in the order confirmation. This technical specification reflects the standard equipment, customer requests deviating from the standard will be shown in quotations or order confirmations.

Condition: good (used), Year of construction: 2004, Peripheral devices Brand: Tool - Temp Type: TT - 157E Isdpsh Hbpwefx Angsbb Available: 14 pieces

Condition: as good as new (ex-display), PFAFF 8320 - 111/101 long-arm version with table Iodsxa D Hropfx Angjbb

Condition: new, *TECHNICAL SPECIFICATION: Heating power hot circuit: 48 kW heating capacity cold circuit: 12 kW cooling capacity hot circuit: 42 kW cooling capacity cold circuit: 270 kW medium: water up to 200°C Max. external volume: 10 ltr at 200°C Ibedpfjg Ey Ufjx Angsb Max. flow rate: up to 200 l/min  max. delivery pressure: up to 6,5 bar motor power: 5,5 kW Dimension LxWxH: 1.395 x 753 x 1.180 mm Weight approx. 580 kg *HIGHLIGHTS EQUIPMENT: -regulation and control via SPS with touch screen -heating via stainless steel tubular heating elements made of Incolloy -Heating control via solid-state relay -control box IP54 externally ventilated2 -electrical wiring on terminal blocks -pot. free input for signal for cold/warm changeover (front door) - Pot.-free contact for collective alarm on 3-pin plug-in connector (front door) (front door) -temperature control unit with heating and cooling circuit, for connection of a valve station for quick changeover between hot and cold circuit -temperature controlled feed of the return water -level monitoring with automatic level compensation -dirt filter in the cooling water supply and in the return of the circulation system -Separate automatic filling with strainer -Flow measurement in differential pressure principle in both circuits -monitoring of the heating rod surface by temperature sensors -System pressure control, necessary compressed air connection: 6 to 8 bar -booster pump type DS 360 for water make-up -corrosion-resistant components (VA, MS) -unit mounted on rollers and ready for connection *OPTIONS: -System EcoTemp for intermittent operation -connection for ext temperature sensor PT100 or type J/K -Remote touch screen with 15 m cable Visit our website for more details or for other performance classes. *This device is compliant with the European Directives. Other directives and standards are only fulfilled if they are listed in the order confirmation. This technical specification reflects the standard equipment, customer requests deviating from the standard will be shown in quotations or order confirmations.

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Iodpowlp Hdsfx Angobb Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: new, New equipment MASS International Angled conveyor / flow conveyor L - Conveyor belt with a fixed angle of 35° available for short-term delivery MASS International Angled conveyor NC1 Conveyor belt with a fixed angle and collection trays in the infeed section Example as shown: NC 1 Infeed section 600 mm Inclined section 1300 mm Usable width 250 mm Iedpfx Aohm Axgongjbb External width 305 mm (without motor) Height adjustable, discharge height 750 - 1050 mm Fixed angle between the infeed and inclined sections Adjustable inclination Cleat height 30 mm Cleat spacing 500 mm Belt speed 3 m/min Mobile on steerable castors Optional: Other dimensions, see standard delivery list Dimensions according to customer requirements FDA-compliant belt Modified belt speed etc.

Year of construction: 2000, condition: used, Used filterless hopper loader Ijdpfxsdlpynj Angsbb

Condition: new, Year of construction: 2026, Precision lead and feed screw lathe Manufacturer: OPTIMUM Model: OPTiturn TZ 4 Item No.: 3432240 Condition: New machine Ibodpfx Aogqw U Rongeb Center height: 200 mm Distance between centers: 800 mm Spindle speed: 45 - 1,800 rpm (16 steps) Standard equipment: - 3-axis digital display DPA 32 - Fixed center, MK 3 - Quick-change tool post, size B - Turning tool holder BD - Reducing sleeve MK 6 / MK 3 - Steady rest, fixed, ø 10 - 130 mm - Traveling steady rest, ø 10 - 100 mm - Coolant system - Chip tray, pull-out - LED machine lamp - Operating tools

Condition: new, *Technical Specification: device type: 6/95 heating capacity: 6 kW cooling capacity: 45 kW Medium: water up to 95°C maximum external volume: 50 ltr at 95°C *Equipment hydraulic: - Cooling and filling controlled by solenoid valve - Automatic from cooling water or manual filling (at filling nozzle/option) - Level monitoring by magnet float-switch - Dirt trap in from process line of circulating system and cooling water inlet - Pump reversing for leak-stop operation - Manual mould draining via leak-stop operation and venting by tap at backside of unit - Filling time monitoring and aquatimer - Cool down mode (temperature adjustable) - Adjustable temperature alarm - Options: filling nozzle, interface cable, mechanical flow metering *Equipment electrical: - Controller SBCmini, with relay for collective alarm 230V switchable, on the back of controller on terminal - Heating control by SSR - Control cabinet IP54 - Interface 20mA TTY; pinning Arburg Iodpfxjfnvvio Angebb - Cekon plug 16A *General equipment: - Corrosion resistant components (stainless stell, brass) - Heating rod made of Incoloy - Unit mounted on rolls, two pieces steerable with break - Additional temperature fuse for safe heating switch-off by contactor *Cooling: Power: 45 kW (stainless steel plate heat exchanger) Cooling water connection: Socket G3/8" IG (Performance data at 80°C flow and 15°C cooling water temperature and a pressure difference between cooling water inlet and outlet of 3 bar) *Pump: Type: T401 Output rate (max): 40 ltr/min Pressure (max): 3,8 bar Motor capacity: 0,5 kW Construction: submersible pump / peripheral wheel *Dimensions/Weights/Colours Dimensions L/W/H: 514 mm x 238 mm x 493 mm (w/o conne.) Weight: approx. 30 kg Colour: Case: RAL 7035 light grey Front door: RAL 5015 sky blue *Connections: Circulating medium int. thread G1/2" Cooling water int. thread G3/8" Filling (option) *This unit complies to the European Directives. Other directives and standards are only fulfilled if they are listed in the order confirmation. This technical specification reflects the standard equipment; customer requests deviating from the standard will be indicated in offers or order confirmations.

Condition: like new (used), Year of construction: 2013, BLOW EXTRUDER HDPE Model EuroTruder 75 Made by Euro-Stel, Belgium YOM 2013 extruder: diameter 75x28 D - with neck sweder and granulate hopper Ibjdpjwivdksfx Angeb mold is not included EXCELLENT CONDITION