Punching and biting machine

GEKA Puma 150 T

Condition: new, - Semi-automatic - Hydraulic - Infinitely adjustable band saw speed - Double miter - Hydraulic clamping of the miter setting - Hydraulically adjustable sawing pressure - Fully hydraulic material clamping - Hydraulically adjustable clamping pressure - Cooling system Dodpfxjvkkl Ts Afnjun - Automatic switch-off - Automatic switch-off of the machine at open cover, torn belt, reduced belt tension - Emergency stop - Documentation - 400V

Condition: used, Year of construction: 2001, Cast resin epoxy distribution transformer 630kVA manufactured by TESAR Italy, voltage ratio 10000 ( ± 2 x 2,5 %) /400V, Dyn5 or Dyn11 or Dyn1, IP23 or IP00, forced cooling AF, conductor Al/Al, temperature monitoring unit, functional,available 2 pcs. Dujdpfx Aoquwtxefnen

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Duodpfx Aehzbipefnen Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Year of construction: 2025, Maximum pressure: 40 tons Stroke length: 250 mm Maximum speed: 10mm/sec Return speed: 20mm/sec Work table: 660x1250 mm Working height: 900 mm Oil tank: 60 Liter Maximum workpiece height: 250 mm Duodpfxshgihks Afnon Strip capacity: 200x26 mm Pipe capacity: 60x5.0 mm *not with standard tools - Digital limitation of the stroke and the return stroke. - NC control. - Hydraulic pressure adjustable - Bending speed adjustable - Completely closed table - The ZOPF construction makes it possible to change tools quickly and without loss of accuracy - The hydraulic cylinder is mounted on the heavy-duty machine table, which means that even under heavy load there is no loss of accuracy occurs. - With the universal tool holder and the various tools, you can work extremely flexibly.

Condition: used, Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/A Machine. No. 9566 Year of construction approx. 2000 Punching force 80 ton. throat 300 mm Punching up to Ø 40 mm in 14 mm sheet metal Flat material shears 450 x 15 mm Angle steel shears 130 x 130 x 13 mm Square shears 45 x 45 mm Round material shears Ø 45 mm Duodpfsrz Tutex Afnen Rectangular notcher up to 12 mm Motor power 5.5 kW Mains connection 400 Volt, 50 Hz - Fence with el. stroke release 500 mm - Work table with stop for punching device 550 x 380 mm - Working height of the punching device 1100 mm - Work table with stop for the rectangular notcher 550 x 400 mm - Working height of rectangular notcher 930 mm - approx. 21 different punching tools - operating instructions - Original paint finish, not repainted Space requirement L x W x H 1800 x 1150 x 1950 mm Weight 1.7 tons. very good condition

Condition: used, Year of construction: 2004, Technical details: x-travel: 600 mm y-travel: 400 mm Dusdpfx Aek Hdu Dsfnsn z-travel: 400 mm number of spindle speeds: 63 - 3.150 1/min feed stepless: 12-3000 / 6-1500 (Z) mm/min quill stroke: 100 mm milling-head swivable +/-: 90° spindle taper ISO: SK 40 surface area: 630 x 400 mm total power requirement: 8 kW weight of the machine ca.: 2,2 t dimensions of the machine ca.: 2 x 1,9 x 1,95 m universal milling machine with point to point control, mechanical handwheels, swivel - rotary table (mech.) +-45°, hydr. tool clamping, half cabin, coolant device, manuals (German language) *

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Dodpfx Afsgpxc Sonjun Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet

Condition: new, Semi-automatic band sawing machine for cutting solid bars and profiles of medium size with high efficiency and excellent cutting precision. The robust structure gives the machine the necessary rigidity and precision to the cutting unit. Belt drive with two-speed motor and special gearbox with bronze gear and hardened and ground worm screw. Duodpfx Afofibd Tsnsn Suitably dimensioned flywheels Sturdy ribbon guides made with watertight invitation bearings and adjustable widia plates Belt tension obtained by means of an electromechanical device with microswitch blade rotation control Accident prevention safety device on the flywheel cover cover and on the blade Cutting thickness 1.5 mm Cutting range 60°sx 60°dx Adjustable stop for cuts of the same size Brush belt cleaning device Hydraulic power unit motor 0,37 kW 0.09 kW electric pump for belt refrigeration Jaw height 200 mm Clamp jaw length 185 mm Worktop height 760 mm Machine weight 820 kg

Condition: used, Year of construction: 2007, machine/vehicle number: 001669, Lg 33121 Single side decoiler ARKU AH 3000/ST-M year of manufacture 1995 belt width max. 600 mm load capacity max. 3.000 kg coil outer diameter max. 1.800 mm Spreading hydraulic Pressing arm hydraulic Dedpshigmbefx Afnsun Decoiler with auxiliary drive and brake coiler chair fixed + reel traversing device with: Lg 33221 High performance belt leveler LORENZ BRM 50/620.9 year of manufacture 2007 Machine no. 001669 passage width max. 620 mm number of straightening rolls 9 Straightening roll diameter 50 mm Material density 0.7 to 6.0 mm Straightening rolls supported several times against deflection All rolls driven by transfer gearboxes and cardan shafts. cardan shafts. Used, in as-is condition from stock, available immediately. On request with overhaul. Delivery time by agreement. Further data shortly or on request.

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 Dujdpecxxx Refx Afnon sheet thickness - min.:0,4 mm sheet thickness - max.:3,5 mm weight:0,4 t dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm control, very good condition