Circular Vibrating Screen / Pre-Screen

Kleemann VU1S 1240ST

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Kedpfxjvgrh Us Ab Tewu Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: refurbished (used), functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Technical specifications conveyor belt: Ksdpjxl Rqbofx Ab Tjwu Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: like new (used), Year of construction: 1995, manufacturer: Kleemann Kedpfsr A Dm Sox Ab Tswu year of construction: 1995 type: SHB 10/90 opening size: 1020 x 900 mm impactor weight: ca. 14,9 to

Condition: good (used), Year of construction: 1956, Heavy lathe, turning machine, lathe, center and feed screw lathe, center and feed screw lathe -Manufacturer: Weisser, lead screw lathe type PF200 -Turning length: 1340 mm -Turning Ø over bed: 420 mm -Turning Ø over support: 240 mm -Spindle bore: Ø 41 mm -Spindle speeds: 31.5 - 1400 rpm -Three-jaw chuck: Röhm Ø 250 mm Kjdpfjtzf N Rex Ab Tswu -Accessories: incl., see photos -Tailstock mount: MK4 -Drive motor: 2.5/3.5 kW -Dimensions: 2670/1000/H1230 mm -Weight: 1450 kg

Condition: used, Year of construction: 1974, turning diameter over bed slide: 480 mm, center width: 1,500 mm, Center Lathe Manufactured by Heidenreich & Harbeck Type Hanseat 480 Fully overhauled in 2012 Technical Specifications Manufactured by Heidenreich & Harbeck Type: Hanseat 480 Year of construction: 1974, fully overhauled in 2012 Control: Conventional Center distance: 1500 mm Turning diameter over bed: 480 mm Ksdjwm D Ilepfx Ab Tjwu Turning diameter over support: 295 mm Spindle speed: 20 – 2190 rpm Dimensions: L 3.50 x W 1.20 x H 1.55 m Machine weight: 1200 kg Equipment - 3-jaw chuck D 250, built-in - Faceplate D 400 - 10 quick-change tool holders - 1 steady rest All information is provided without guarantee. A live demonstration is possible at any time in our exhibition hall.

Condition: ready for operation (used), Hsm HL 4809 LI baler - Large filling opening, ideal for big boxes - Container tipper for convenient filling Pressing force in kN: 480 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg Kodpfjra Dddjx Ab Tewu - Bale dimensions (length x width x height in mm): 1200 x 1100 x 750 - Machine dimensions (length x width x height in mm): 5648 x 1849 x 2515 Idle cycle time in seconds: 53 - Manual tying: 4 times with wire

Condition: ready for operation (used), Year of construction: 1999, IMMEDIATELY AVAILABLE, chamber filter press from Häcker with base frame and 50 m3/h Abel pump, plate format 1200 x 1200 mm, approx. 90 PP plates, 30 mm cake, content approx. 2700 liters, automatic. Plate transport, open outlet in filtrate trough on both sides, press is ready for use immediately after assembly, Abel pump was serviced by the manufacturer shortly before it was taken out of service, galvanized base frame with staircase, location is near Würzburg / Germany Ksdporunu Ijfx Ab Tewu

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 25 h, functionality: fully functional, Equipment: rotational speed infinitely variable, Crusher Equipment Including: Special tools, reinforced, 7/7 tool carriers with 4 tools each (tools consist of main, pre-crushing, and post-crushing blades) Shaft speed individually and infinitely adjustable, approx. 0–41 rpm Including post-crushing bar Including tilting skip Drive Unit Drive power: 294 kW Including Scania diesel engine, Stage 5 Including standard noise reduction package Including Power RAM pre-cleaner Including central lubrication for the 4 main bearings Including Cleanfix Kwjdou Hgllopfx Ab Tju Including swiveling cooler Electrics / Controls Including IFM display Including radio remote control Including four shredding programs (wood, waste, special, and green waste) Discharge Conveyor Including discharge conveyor Custom Equipment Including preliminary armoring of tools Including overband magnet, hydraulically height adjustable – neodymium – Including hopper extension on 3 sides, approx. 800 mm each Including electric pump for hydraulic oil Including GPS module Including rubber tracks Including pressure sensors Including additional noise-reducing cassette (-10 dB(A)) Refurbishment / Service Refurbishment and service by HAAS

Year of construction: 1983, condition: good (used), 1 Bracket milling machine make: RECKERMANN, type: KOMBI 900, year 1983 ser. no. 6367P, table size 1.000 x 310 mm, travel X/Y/Z 720 x 220 x 450 mm, tool holders SK 50, HD machine vice, Kwodpfxeh E Du De Ab Tsu spindle speeds: 3...2800 rpm

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. Ksdpfxstvau Aj Ab Tewu All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.