Construction rubble - crusher, shredder

AM 650X750

Condition: good (used), Year of construction: 2004, functionality: fully functional, Manufacturer: HABERMEHL Anlagenbau GmbH Address: Hauptstr.1, 35510 Butzbach-Ebersgöns, Germany Type: EH 400/1 Serial number: 901 Year of manufacture: 2004 Voltage / Frequency: 400 V / 50 Hz Rated power: 3 kW Kdsdpjw Niuhofx Am Uel CE-certified: Yes 🛠️ Device Description Industrial shredder or crusher (Shredder/Granulator). Notable features visible in the photos: - System with rotating knives (shredding unit) on a 2 mm shaft - 3 kW SEW motor and reduction gearbox - 8 mm screen (the screen is labeled “8 mm Sieb”) – determines the output particle size - Rollable, portable design - Material discharge container and lower motor drive system Machines of this type are typically used for shredding the following materials: - Plastics - Rubber - Wood - Light metal chips - Electronic scrap 📝 Technical information you should request If you require further details, you may request the following information from the supplier or manufacturer:

Year of construction: 2025, condition: new, functionality: fully functional, High Speed · High Precision · High Stability Kdedpfxowwzudo Am Usl The VS series high-speed laser tube cutter for small pipes has arrived! This machine features a high-precision chuck system designed specifically for tube cutting. With excellent sealing and dust protection, it delivers clamping accuracy within ≤0.1mm ideal for ultra-precise small tube processing. The chuck rotates up to 160 RPM, with acceleration reaching 1.5G, easily enabling high-efficiency processing of small-diameter tubes. easily enabling high-efficiency processing of small-diameter tubes. it supports true ultra-short tail cutting saving cost from the very beginning. Available in 3000W and 6000W, Handles square and round tubes from 10mm to 120mm in diameter, Also capable of cutting angle steel, channel steel, and I-beams A true all-rounder for small pipe fabrication. Supports automatic or semi-automatic loading Effortlessly enables smart and automated processing. One machine replaces three workers — A powerful and efficient tool for small pipe manufacturing!

Condition: excellent (used), functionality: fully functional, Timesavers 22 Series 1100-WBB Kdjdpfxsx Uwlao Am Uol 1st Station: Abrasive belt for pre-grinding, ideal for removing burrs, laser scale, etc. Optionally, the abrasive belt can be switched to a Scotch-Brite/non-woven belt to achieve a surface finish on the parts. Easy belt change in under a minute thanks to quick-change system. The belt speed is continuously adjustable. 2nd & 3rd Station: Disc brushes for edge rounding, two stations in sequence with both left and right rotation for optimal results. Eccentric mechanism enables lateral oscillation of the disc brush stations (can be switched on or off). Easy brush change using the quick-change system. Disc brush speed is continuously adjustable. Conveyor belt speed is steplessly adjustable. Working width: 1100 mm Maximum part thickness: 100 mm The machine is fully operational and can be inspected and tested under power on site.

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation Kdjdpsvbtpofx Am Usl -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Condition: new, functionality: fully functional, New machine - stock clearance sale - Tipping is mechanical. The stated price is net ex warehouse location. Kjdpfjw Sfdwjx Am Usdl

Condition: excellent (used), the plant is consisting of: - 2 chain separators Kdedpfx Amslxzl Eo Uel - 2 55 cbm³ silos with discharge screws - 2 discharge screws - 4 mixing and homogenising chambers, - 5 conveyor belts - 2 double-shaft extruders connected in parallel - 1 double shaft mixers - container for liquid extracts, etc.

Condition: new, Year of construction: 2023, Horizontal bending machine AH 40 Kodjqvm Ukspfx Am Uodl - ZOPF - with semi-automatic control - hydraulic pressure 40 to. - length of stroke - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 250 mm - motorcapacity 3,0 KW - 400 V 50 hz 3 ph. - working height 900 mm - closed table - replaceable wear plate - weight 950 kg - bending capacity: flat material max. 150x22 mm round tube up to 60 mm

Condition: new, Year of construction: 2025, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, pressure: 70 bar, total height: 1,600 mm, total width: 800 mm, total length: 1,200 mm, temperature: 40 °C, operating pressure: 70 bar, noise level: 80 dB, Equipment: documentation/manual, rotational speed infinitely variable, RO 510-DT2-15S – Compact Seawater Reverse Osmosis System, approx. 15,000 L/day Potable Water Compact, fully automated reverse osmosis system for the production of hygienic drinking and process water from natural seawater. Ideal for maritime applications, island supply, hotels, as well as small-scale industrial and utility operations. Technical Specifications Type: RO 510-DT2-15S Process: Reverse osmosis with Disc-Tube (DT) technology Permeate Output: Approx. 15,000 L/day (15 m³/day, depending on operating conditions) Feed Water: Seawater with high conductivity, approx. 55,000 µS/cm (high salinity) Permeate Quality: Drinking water, approx. 500 mg/L residual minerals (reference value) Recovery Rate: Approx. 30% (typical operating range) at 55,000 µS/cm conductivity Design Temperature: Approx. 25°C (Operating range: approx. −2 to 35°C) Process Technology & Configuration DT module with open feed channel – highly fouling-tolerant and fully cleanable Mechanical pre-filtration (high-performance filter + 10 µm cartridge filter) Chemical pre-treatment of feed water (acid dosing) generally not required Integrated rinsing and CIP (clean-in-place) function, PLC controlled Skid-mounted on stainless steel frame (AISI 316) High-pressure lines in stainless steel, low-pressure section in seawater-resistant plastic Pumped seawater components made from corrosion-resistant materials Operating & Energy Data Feed Water Flow: Approx. 1,000 L/h (reference value) RO Module Operating Pressure: High pressure range, designed for seawater desalination Power supply: 230 V, 50 Hz, single phase Connected load: Approx. 6 kW Control, Monitoring & Safety Local operator panel with integrated PLC control Monitoring of pressures, flows, conductivity, and operating hours Kdsdpfxew Uf Ihj Am Usl Automatic shutdown in case of: - Insufficient feed pressure - Exceeding permissible operating pressure - Overpressure in permeate/concentrate lines - Exceeding defined conductivity limits (with automatic redirection to drain) Automatic “Stop & Rinse” function: Permeate flushes all seawater-contacted components on shutdown, reducing fouling during system standby Dimensions & Weight (Skid) L × W × H: Approx. 1,190 × 705 × 1,500 mm Weight: Approx. 530 kg (dry), approx. 605 kg (operating) Typical Applications Vessels, offshore platforms, ports Island and coastal supply Hotels, resorts, small industrial and utility operations Backup or peak load system for existing potable water production Additional technical documentation, photos, and information on scope of supply, pricing, and availability are available on request.

Condition: reconditioned (used), Year of construction: 2000, machine/vehicle number: KK052469, functionality: fully functional, Connected load 380V 4kW table size 1070 x 620 mm Kdjdpfoiinm Hox Am Usl swiveling with hand crank 45 height adjustment with hand crank right/left rotation motor brake socket for feed unit Protective covers for hand milling spindle Ø 30 mm Aigner stop suction connection 2x 120 mm speeds: 1400/3500/6000/8000 rpm Instruction manual

Condition: new, Year of construction: 2026, functionality: fully functional, power: 11 kW (14.96 HP), A triple pass rotary drum dryer is a type of industrial dryer that is used to reduce or remove moisture from a material. It gets its name from the three rotating drums through which the material passes, each with a different purpose in the drying process. This type of dryer is commonly used in the production of various bulk solids, including minerals, agricultural products, and biomass. Here are the key features and components of a triple pass rotary drum dryer: 1. Triple Pass Design: - The material being dried passes through three rotating drums or cylinders, hence the term "triple pass." Each drum serves a specific purpose in the drying process. 2. Material Flow: - The material enters the dryer and first passes through the innermost drum. After the initial drying phase, it moves to the middle drum and then to the outer drum, undergoing additional drying in each pass. 3. Heat Source: - Heat is typically provided by a combustion system, such as a burner or furnace, located at one end of the drum dryer. The hot gases generated by the combustion process flow through the rotating drums, transferring heat to the material. 4. Air Flow: - The dryer is designed to optimize air flow through the drums, ensuring efficient drying. In a triple pass design, the material and hot gases move counter-currently through the three drums, enhancing heat transfer and drying efficiency. 5. Lifting Flights or Lifters: - Lifters are internal components inside the drums designed to lift and cascade the material as it rotates. This movement promotes good heat transfer and uniform drying. 6. Retention Time: - The triple pass configuration allows for an extended retention time of the material in the drying system. This longer exposure to heat enhances the drying efficiency, making the triple pass rotary drum dryer suitable for materials with high moisture content. 7. Cooling Section: - After the material completes the three passes and reaches the end of the drum dryer, a cooling section may be included to reduce the temperature of the dried material before it is discharged. 8. Applications: - Triple pass rotary drum dryers are used in various industries, including agriculture (drying crops like grains), minerals (drying ores or concentrates), and biomass (drying wood chips or other organic materials). Kodpfx Ameq Nfuzo Usdl 9. Efficiency and Energy Consumption: - Triple pass rotary drum dryers are known for their high efficiency due to the extended drying time and effective heat transfer. However, they may have higher energy consumption compared to single or double pass dryers. When selecting a triple pass rotary drum dryer, it's essential to consider factors such as the type of material to be dried, required moisture reduction, and overall processing requirements. Proper design and operation are crucial to achieving optimal drying performance. Technical details We have different options for different requirements, please contact our team for more info.