Used waste compactors for sale (313)

Condition: good (used), Year of construction: 2019, functionality: fully functional, Horizontal baling press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2019 Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 21 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-wire, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Hedjzh Iigspfx Aarep Materials: Paper, cardboard, film Note: The press is in good condition. The operating manual is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is subject to change, sale is subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against prepayment, ex works, without warranty.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Hodpfx Aajy S Rqwerep Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: Hodpfey R Nnfex Aarep o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2015 Manufacturer: Dixi Type: Dixi 60 SLD Hodpfx Ajzgvbujarep Year of manufacture: 2015 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available for you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and for any errors. The offer is subject to change, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: good (used), Year of construction: 2016, operating hours: 1,060 h, functionality: fully functional, Baling press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2016 Hodpfx Aaoy Ni Sherep Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2016 Operating hours: 1030 Drive power: 11 kW, 400 V / 23 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Pressing cycle: approx. 35 s Capacity: approx. 1000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 3-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film Note: The press is in very good condition. It has been inspected and tested at our facility in 28816 Stuhr. The video can be found on our website or our YouTube channel. The hydraulic hoses should be replaced. We will gladly answer any questions you have about the machine by phone from Monday to Thursday from 08:00 to 14:00. On Friday, we are available to you from 08:00 to 13:00. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without warranty.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Bale press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2017 Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2017 Drive power: 11 kW, 400 V / 21 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Pressing cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Hedpfx Aaoy Ni I Aerjp Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2013, functionality: fully functional, Baling press Dixi 60 SLS, year of manufacture 2013 Technical data: Manufacturer: Dixi Year of manufacture: 2013 Pressing force: 60 t Drive power: 11 kW, 23 A Hsdpfx Asy Ni Hrearsp Feed opening: 990 x 1110 mm (W x L) Bale dimensions: 1100 x 800 x 1200 mm Bale weight: approx. 370-450 kg Tying: 3-fold manual Machine dimensions: approx. 4870 x 2100 x 2150 mm (L x W x H) Weight: approx. 5220 kg Materials: Paper, cardboard, film The press is in good, fully functional condition and has been inspected and tested by us. You can find the video on our website or YouTube channel. We will be happy to answer any questions you may have about the machine by phone, Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available to you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without warranty.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2012 Manufacturer: Dixi Type: Dixi 60 SLD Hedpsy Ni Dqsfx Aarsp Year of manufacture: 2012 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-strand, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Material: Paper, cardboard, film The press is in good condition. We will gladly answer any questions you have about the machine by phone, Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2015 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2015 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Hjdpfx Aaoy Ni Eusrsp Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available for you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and for any errors. The offer is subject to change, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: as good as new (ex-display), Year of construction: 2022, Briquetting press for aluminum or steel chips Extremely high pressing force of 3,700 kg/cm² 9 kW Large hopper: 600 x 1500 mm Briquette size: 60 x 40 mm Hsdew Ig Suopfx Aarep Throughput: Aluminum chips – up to 70 kg/h Steel chips – up to 180 kg/h Brass chips – up to 220 kg/h *depending on the raw material and settings Includes: - Emulsion tank - Emulsion pump - Oil cooler

Condition: used, Year of construction: 2003, Technical details: pressure: 58 t box depth: 1145 mm material: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen bottles Feed opening: L: 1145 x B: 600 mm voltage: 400V / 50 V / Hz Hedpfezgvhuox Aarep total power requirement: 4,0 kW weight of the machine ca.: 2,6 t machine dimensions LxWxH: ca. 1,07 x 1,84 x 3,1 m Anwendung: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen platzsparende Recycling Lösung kompakte Bauart automatische Pressplattenrückführung, dadurch erhöhter Bedienkomfort Öffnung an der Vorderfront Tür horizontal verschiebbar ca. 600mm Presskammer/Ballengröße: LxBxH: 1000 x 600 x 600 mm (0,36 m³) Bindeeinheit Band- und/oder Drahtabbindung Bedienung über Schalttafel *

Condition: used, Year of construction: 2005, Technical details: pressure: 58 t box depth: 1145 mm material: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen bottles Feed opening: L: 1145 x B: 600 mm voltage: 400V / 50 V / Hz total power requirement: 4,0 kW weight of the machine ca.: 2,6 t machine dimensions LxWxH: ca. 1,07 x 1,84 x 3,1 m Anwendung: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen platzsparende Recycling Lösung kompakte Bauart automatische Pressplattenrückführung, dadurch erhöhter Bedienkomfort Öffnung an der Vorderfront Tür horizontal verschiebbar ca. 600mm Presskammer/Ballengröße: LxBxH: 1000 x 600 x 600 mm (0,36 m³) Bindeeinheit Band- und/oder Drahtabbindung Bedienung über Schalttafel * Hodpfx Aaszgvhhorsp

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. Hsdpfx Aaszdn H Rorsp We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), year of last overhaul: 2025, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Hedjzdny Ropfx Aarsp Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Hodpezdnxgofx Aarjp Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Hjdpszh Eztefx Aarsp Condition: very good! Video of the machine in operation available on request. Transport also possible.

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, Well-maintained Bramidan baler for high-volume waste compacting. Hsdpfx Aezhnpyearjp

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, Well-maintained container tilter for roll containers. Hjdpfxjzhnnie Aarjp Several units available for purchase or rental.

Condition: used, Year of construction: 2020, functionality: fully functional, pressing force: 120 t, filling opening width: 2,000 mm, filling opening length: 1,000 mm, bale width: 750 mm, bale height: 1,100 mm, total width: 2,835 mm, total height: 4,374 mm, total length: 19,627 mm, overall weight: 43,000 kg, warranty duration: 12 months, power: 75 kW (101.97 HP), Equipment: documentation/manual, For sale is a baling press, model "HP-G 4 120 VG6," manufactured in 2020, featuring a 6-strand vertical PP twine tying system. The pictures show the machine in its assembled condition. It is now located at our facility in Lathen. The press is sold without a conveyor belt. Before delivery, the machine will be completely overhauled and technically refurbished by our qualified personnel. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operation. The overhaul includes, among other things, the following services: Hjdpfx Aaozhudqsrjp • Disassembly and inspection of the relevant machine components • Evaluation of all wear-relevant components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, slide guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of the hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and connecting elements • Inspection of the electrical components and safety devices • Inspection and readjustment of the tying device • Cleaning, assembly, and commissioning of the overhauled system • Performance of functional and load tests after completion of the work Thanks to the comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We will be happy to provide you with further information, photos, or a customized offer. If you are interested, we look forward to hearing from you.

Condition: used, Waste compactor, baler, waste baler, chamber baler, Orwak Compactor 3110, used machine Manufacturer: ORWAK (Sävsjö, Sweden) Type: Compactor 3110 Serial No: 105441 Hjdpfx Aasy S Ui Dorsp Product No: 4903110-00 Overall dimension: 865 x 680 x 2050 mm -press force: 4t -production date: 2011-11 -voltage: 230 V -frequency: 50 Hz -power: 1.1 kW -current: 8.9 A -weight: 340 kg

Condition: used, Year of construction: 2007, functionality: fully functional, machine/vehicle number: 10554, type of input current: three-phase, input current: 23 A, input frequency: 50 Hz, input voltage: 400 V, RUF 4/3700/60x40 Briquetting System incl. Chip Hopper – Industrial Plant High-performance briquetting system for metal chips Incl. chip hopper / material feed – ready for immediate use Proven RUF quality “Made in Germany” High compression for better storage and marketing Reduction of disposal and transport costs Technical data Manufacturer: RUF Type: 4/3700/60x40 Briquette size: approx. 60 x 40 mm Pressing capacity: approx. 3,700 kg/h Drive: hydraulic Material to be processed: metal chips (steel, stainless steel, aluminum, etc.) Equipment Large chip hopper / chip container 1 m³ that can be loaded with a forklift Automatic feeding system via screw conveyor in the hopper Hydraulic briquette press Control unit Discharge of finished briquettes Compact, industry-proven design Hedpfx Aozh Eqbsarsp Application areas Machining companies Turning shops / milling shops Metal and steel construction Recycling and recovery Automotive suppliers Condition Used, operational. The system has already been dismantled. Advantages of briquetting: Significant volume reduction of chips Recovery of coolants Higher sales revenue for briquettes Clean storage and logistics Sustainable production

Condition: as good as new (ex-display), Year of construction: 2026, The BTS-MF450HD special waste baler is the ideal baler for compacting difficult materials such as PET bottles, food cans and metal containers, big bags, plastic canisters and plastic packaging, but also scrap tyres and car bumpers can be reduced to a minimum of volume with the baler. The special baling press impresses with its ease of use, safe operation and its spacious filling chamber, it is ideal for medium to large amounts of material. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 30 Ton Bale weight: up to 450 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 3343 H x 1781 W x 1196 D mm Machine weight: 1600 kg Transport height: 2300 mm Loading aperture: 1200 W x 680 H mm Cycle times: 40 seconds Motor: 5.5 kW 16 Amp Power supply: 380 - 400 V (3 phase) Noise level: 68 dB Extra-long dual cylinders for even and early compaction of the material User-friendly lever control Bale kicker for easy eject the bales Extra retainer for reducing the material spring back Reel holder for 4 rolls of strapping A quality product “Made in Europe” Hjdpovug Dysfx Aarjp Suitable for compacting PET bottles Food cans and sheet metal containers Canisters and plastic containers / packaging Scrap tyres and car bumpers Big bags Cardboard and plastic film / foils Other difficult valuable materials Optional extras Machine colour RAL PLC auto compaction cycles with bale full light and E-stop with locking key Sliding top door Strapping rolls / bale wire Motor 11 kW 32 Amp Demo-Video shows BTS-MF550HD Special Waste Baler. Can Baler, Can Waste Baler, PET Baler, PET Compactor, Tyre Baler, Tire Baler, Scrap Tyre Baler, Scrap Tire Baler, Tyre Compactor, Tire Compactor, Can Baler, Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Bale press Presto CC 50 M, year of manufacture 2015, with lifting and tilting device. Technical data: Manufacturer: Presto Hjdpfx Aaszc Hz Esrop Type: CC 50 M Year of manufacture: 2015 Operating hours: 1932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Feed opening: 1030 x 1100 mm Feed volume: 0.85 m³ Tying: 3-wire, manually Throughput at a bulk density of: 35 kg/m³ - 1.3 t 60 kg/m³ - 1.7 t 100 kg/m³ - 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (L x W x H) Machine weight: approx. 4000 kg Materials: Paper, cardboard, film The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or our YouTube channel. Please note: All technical data refers to the manufacturer's specifications. We assume no liability for the information provided or any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Baler Presto CC 40 M, Year of manufacture: 2017 Technical Specifications: Manufacturer: Presto Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Feed opening: 1080 x 1100 mm Feed volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Throughput rate at bulk density of: 35 kg/m³ - 1.8 t/h 60 kg/m³ - 2.5 t/h 100 kg/m³ - 3.1 t/h Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Hedpfxozc Hy Uj Aarop Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Operating instructions and CE declaration are available. Note: Channel discharge is fully automatic and regulated. Please note: All technical data is based on the manufacturer's information. We do not accept liability for the information provided or any possible errors. This offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex-works, prepayment required, without warranty or guarantee.

Condition: used, Year of construction: 2015, functionality: fully functional, machine/vehicle number: M32961, year of last overhaul: 2025, Self-pressing container (Absetzer), year of manufacture: 2015 Unladen weight: 2,500 kg SN: 31047, Colour: Blue Last service: 05/2025, last UVV: 05/2025 It was in active use until January 2026. The press was extensively tested today (27/04) and is ready for immediate use. The press has a superstructure in which weighing technology was installed. This has been removed. Material is fed into the press via the side door. The enclosure can be removed at any time by loosening the screws. Hsdoyymraopfx Aarop Then the press is in its normal state. Location: DE - 58730 Fröndenberg