Machining center

Morbidelli

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Nsdexy Tmnjpfx Ag Ioku

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Nkedpfowu Tu Dox Ag Iju Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, machine/vehicle number: 008388, X axis working area: 3086 mm Y axis working area: 2185 mm Working Table: Flat table Njdpfxjyngzvs Ag Ijku Main Electrospindle power: 15 KW Number of controlled axes: 4 axes Total number of drilling spindles: 18 Total number of tool changer positions: 20

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground ball screws of the highest precision class. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. Such characteristics are important for ensuring balanced movement even in more complex tasks. The movement of the various axes is controlled by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters that can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different P Nkedpfx Agevvi Nzo Iju

Condition: used, Year of construction: 2014, power capacity 3 kW Nksdpoh A Sfdefx Ag Isu feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Voltage/frequency: 415 V / 50 Hz Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW 1x Beko Öwamat 2 - oil-water separator Technical data was taken from publicly available sources

Condition: used, Year of construction: 2020, CNC-CONTROLLED MACHINING CENTER WITH MULTIFUNCTIONAL TABLE - WORK CELL VERSIONX400 CELLDrilling and milling made for you!The numerically controlled machining center is equipped with a wide range of milling/drilling tools to meet every need in the processing of wood and similar materials.- More powerful, with drilling spindles with 8,000 rpm and . Technology, the toughest spindle available on the market, with over 1,000 maintenance-free hours of use. Better and more comprehensively equipped, with various configuration options thanks to the multifunctional table to optimally equip the machine according to your needs. Easier and more understandable programming thanks to the integrated MAESTRO CNC CAD-CAM module. Easier to use: the work table is accessible at all times, the electrical cabinet and vacuum pump are integrated, and in the PRO SPACE configuration there are no guards. Supporting structure. The supporting structure consists of a particularly strong monolithic steel base, heavily ribbed and very rigid. The particularly wide support was specifically designed to give the machine stability, ensuring consistent precision regardless of the working conditions and eliminating the need to anchor the machine to the floor. The base forms a large and solid support for the mobile column: the work unit is thus equipped with a balanced, stable, and durable support that can withstand the most extreme stresses, ensuring higher quality performance and greater precision. The mobile gantry consists of a single, solid unit anchored to the base on both sides and slides on pyrotechnic guides with top-quality ball-return slides. The dual motorization along the X-axis ensures top performance even under demanding working conditions. The movement of the lower moving unit (X-axis) and the working unit along the rod of the moving unit (Y-axis) is achieved thanks to a rack/pinion transmission with helical teeth. this creates a greater tooth-to-tooth thrust which achieves greater acceleration and greater speed along the X and Y axes. The specially designed helical gearing ensures less wear on the mechanical components and less noise. The vertical Z axis is driven by a screw with ball return which ensures perfect balance with dynamic loading and strong acceleration and deceleration. The main milling unit is directly coupled to the Z axis carriage and ensures absolute quality of finishes as any vibrations are completely eliminated. Translation along the X-Y-Z axes is carried out by brushless motors driven by static inverters; These ensure: - Reduced processing times thanks to improved acceleration - Better positioning accuracy thanks to the high-resolution encoder - Zeroing of setup operations when switching on the machine thanks to absolute encoders - Zeroing of general maintenance operations since there are no brushes with the "brushless" system The management of the axis displacement and, in general, of the machine's working elements is carried out by an industrial NS module with digital D Nsdsvvi N Iopfx Ag Isku

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground, high-precision recirculating ball screws. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. This characteristic is important for ensuring balanced movement even in more complex tasks. The various axes are driven by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters, which can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different Nkjdpfevvi Rfsx Ag Iou

Condition: good (used), functionality: fully functional, We offer for sale a complete line for multi-point automatic welding of SCHLATTER brand steel wires. We have three fully operational production lines. There are also automatic machines for the production of transverse wires (so called slitting machines with a cutter). Nkjdotvpilepfx Ag Iju We also have a number of single point welding machines for steel wires.

Condition: used, Bar Machining Center Nkodpowh A Hisfx Ag Iju 3-Axis

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Work in X, Y, Z axes Working area 3100 x 1340, Z axis = 180 mm Horizontal drills on X axis – 6 pcs Nedpfsx Upffjx Ag Ijku Horizontal drills on Y axis – 4 pcs Vertical drills on X axis – 8 pcs Vertical drills on Y axis – 6 pcs Two tool magazines: side – 11 positions and transfer – 14 positions Grooving saw on X axis Spindle 8 kW, air-cooled, 600–24,000 RPM, HSKF63 Becker Vacuum Pump 2.2 kW Option for dual-field operation X axis speed – 25 m/min (programmable) – 56 m/min (vector) Y axis speed – 50 m/min (programmable) – 56 m/min (vector) Z axis speed – 15 m/min

Condition: excellent (used), Line for door jambs (frames), with END-CUTTING, ROUTERING for COUNTER-PLATE and HINGE INSERTION (Anuba). Composed of: X10030A) Loading Conveyor X10030B) Transfer Conveyor X10030C) Double-end cutting and drilling machine "AMS" Nksdpfx Asqwyclog Isu - Left-side Cutting 45° - Drilling - Cutting 90° - Right-side Cutting 45° - Drilling X10030D) Angular Conveyor (90°) X10030E) Anuba Inserting Machine "MASTERWOOD" Mod. MULTITEC X10030F) Strike Plate Routering Machine "MASTERWOOD" Mod. Teknomat 3000

Condition: used, machine/vehicle number: 008340, X axis working area: 4400 mm Y axis working area: 1300 mm Working Table: Pod and Rail Main Electrospindle power: 11 KW Nodpfjx A Tg Hex Ag Ieku Number of controlled axes: 5 axes Total number of drilling spindles: 36 Total number of tool changer positions: 30

Condition: used, machine/vehicle number: 005446, X axis working area: 3000 mm Nsdpfxewuciqo Ag Ijku Y axis working area: 1300 mm Number of controlled axes: 3 axes Total number of drilling spindles: 112

Condition: used, Year of construction: 2000, Number of boring spindles 5 St. Working width 230 mm Working height 160 mm Feed motor 4 kW Nodpfx Agowztw So Ioku Feed speed 5-24 m/min.

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, power: 11 kW (14.96 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, travel distance X-axis: 3,548 mm, travel distance Y-axis: 1,350 mm, travel distance Z-axis: 170 mm, workpiece length (max.): 3,540 mm, workpiece width (max.): 1,350 mm, workpiece height (max.): 160 mm, number of axes: 5, number of slots in tool magazine: 12, controller manufacturer: SCM, Equipment: documentation/manual, 5-axis CNC machining center with a very robust design (portal construction) Control via XYLOG and Maestro Extended working area in X-direction (comparable to approx. X5 HD 36) Beam table, details (equipment): 12x TV MORBIDELLI suction cups X=145 Y=145 H=50 Support surface dimensions: 145 x 145 mm Suction cup height: 50 mm Integrated blanking valve 6x Rotatable TV MORBIDELLI suction cups X=145 Y=55 H=50 Support surface dimensions: 145 x 55 mm Suction cup height: 50 mm 6x Rotatable TV MORBIDELLI suction cups X=145 Y=30 H=50 Support surface dimensions: 145 x 30 mm Suction cup height: 50 mm Nedpoymglljfx Ag Ijku Vacuum cups can be positioned using the laser system Tool changer traveling in X-direction, HSK 63 tool holder Chip conveyor, automatic central lubrication The drilling unit consists of: - 10 individually selectable vertical drilling spindles in X-direction - 8 individually selectable vertical drilling spindles in Y-direction - 4 horizontal spindles (2+2) for drilling in X-direction - 4 horizontal spindles (2+2) for drilling in Y-direction - 1 grooving saw unit (max. diameter 120 mm) in X-direction Safety fence (original Morbidelli provided); we use a custom safety solution for the machine, which has been accepted by BGHM. Both safety devices will be supplied. The machine is in very good condition. Demonstration possible by arrangement. Tools and tool holders shown in the photos are not included in the offer. A comprehensive range of tools/tool holders can be purchased on request. Offer is ex works Frankfurt am Main (EXW) Machine available immediately!