Used Bale Collect Dare for sale (3,920)

Condition: good (used), Bale-Pak for pressing shavings in good condition including a scraper conveyor, an ABB stacking robot and an automatic plastic wrapper Codpfx Aeimv N Tjaqjhd

Condition: good (used), Year of construction: 2011, pressing force: 150 t, power: 0.015 kW (0.02 HP), works fine, possible to try 150ton power 15KW Cedpfjrl Tgujx Aaqshd works fine can check

Condition: used, Year of construction: 2025, operating hours: 86 h, Compressed air | Knives: 25 | Pickup-hydraulic | Pickup support wheel | Roller hold-down | Claas Rollant 630 Uniwrap Year of manufacture: 2025, currently 422 bales pressed (as of 26.06.2025) Technical specifications: - Baler-wrapper combination with 1.25 m chamber diameter - Chamber width 1.20 m MULTIFLOW pickup: - Pickup width 2.10 m - Gauge wheels, pendulum mounted, with 16x6.5-8 tyres - Dual feed augers PRO cutting floor: - Hydraulic suspension and lowering cutting floor to prevent blockages - Operation via terminal including optical and acoustic signals ROTO CUT cutting rotor: - Cutting rotor with four spirally arranged tine rows - Individually protected knives against foreign objects - Hydraulic knife group selection Chamber: - 16 profiled steel rollers - Rear door with hydraulic locking - Greasable baler roller bearings Wrapping unit: - Fully automatic control - Twin wrapping arms with 750 mm film pre-stretchers - Wrapping speed max. 36 rpm for 6 layers of film in 23 seconds - Terminal for direct access at the wrapping table - Hydraulically lowerable film magazines for 12 spare rolls - PROFI CAM camera and work light for wrapper illumination - Continuous chain lubrication - Hand wash tank incl. soap dispenser - Hydraulic requirements: load-sensing and 1 x single-acting Cjdpfxowvwtao Aaqshd Equipment: MULTIFLOW Pickup HD with twin roller hold-down Dummy knives, set of 25 ROTO CUT cutting rotor with hydraulic swinging PRO cutting floor, 25 knives PREMIUM LINE knife set, 25 pieces Film pre-stretch 82% Bale transfer guide ROLLATEX net tying Single wide-angle PTO shaft with cam-type clutch, 6-piece Tractor hydraulic connection, comfort Adjustable support stand Hydraulic/electronic ROTO CUT swinging floor K80 ball head hitch, MR Tyres: 600/55 R26.5 Dual-line compressed-air brake system, up to 40/50 km/h LED high-end work lights including service lighting Screen for PROFI CAM CEMIS 700 Automatic central lubrication system, electrically actuated Extended tool set | Internal no.: 11264178

Condition: new, Year of construction: 2025, Attachment suited for: Agricultural machines Cjdpfx Aasxrnv Usqshd

Condition: used, Year of construction: 2007, load capacity: 10,000 kg, For sale: C-hook coil lifting hook PFEIFER Condition: used, but technically sound and ready for work. Reliable lifting device from the German manufacturer PFEIFER Seil- und Hebetechnik, manufactured in 2007. Technical specifications: Lifting capacity: 10 t Design: C-hook coil lifter Manufacturer: PFEIFER, Germany Year of manufacture: 2007 Application: The device is designed for lifting and transporting heavy coils using overhead or gantry cranes. Typical areas of use: Metallurgy – lifting steel, aluminum, or other metal coils Paper industry – handling large paper rolls Logistics and warehousing – safe transport and storage of coils The C-shaped design allows for quick and convenient gripping of the coil by its core, ensuring stable weight distribution. This increases workplace safety and improves handling efficiency. Chodpfsxhgvfox Aaqod If you have any questions, we will be happy to assist you.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, pressing force: 26 t, filling opening width: 1,500 mm, filling opening length: 630 mm, bale length: 1,500 mm, bale width: 800 mm, bale height: 1,140 mm, bale weight: 500 kg, total width: 1,060 mm, total height: 2,576 mm, total length: 2,075 mm, overall weight: 1,220 kg, noise level: 65 dB, power: 4.6 kW (6.25 HP), Powerful bale press Orwak 3820 Power. Codpfoxmvc Esx Aaqehd Extra good machine for big dimensions cardboard or foil because of the extra large feed opening 1500 x 630 mm.

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes - Foams - PET bottles - Insulation mats - and other pressable materials Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Codpsra A E Ujfx Aaqshd Technical Data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Weight: approx. 8.4 tons Condition: Used

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: PL-1, Equipment: hydraulics, For Sale: Avermann Maschinenfabrik Vibrating Table Without (VAT) Made in Germany, suitable for reinforced concrete product forming. Length: 10 meters Width: 4.5 meters Number of Vibrators: 9 The vibrating table is equipped with heating pipes and a hydraulic lifting mechanism. Condition: Used, with visible rust. Chodpfewv Rymex Aaqod Manufacturer: Avermann Maschinenfabrik Year Of Manufacturer: (1992) 1990-2000 Estimated The table features a solid, heavy-duty construction designed for intensive use. It is suitable for both large projects and smaller production facilities. The table is fully operational, although it shows visible signs of wear. Several other vibrating tables are also available.

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, pressing force: 58 t, filling opening width: 600 mm, filling opening length: 1,190 mm, bale length: 1,100 mm, bale weight: 450 kg, total width: 700 mm, total height: 1,000 mm, overall weight: 2,300 kg, STRAUTMANN PP1207 Single chamber baler - Very good condition. Low running. 70*110*80-100 cm 58 tons of pressing force 70 cm deep chamber 60cm high door opening Quick Door auto door hydraulic bale dropping Possible recyclable materials: Cardboard, film, PET bottles, foam, cans, electronic scrap Bale size (LxWxH): 1200 x 700 x 800 mm Bale weight: approx. 400 - 500 kg External dimensions (LxWxH): 1844 x 1067 x 2868 mm Transport height: 1970 mm Filling opening: 1145 x 430 mm Throughput: 1 - 2 bales / hour Number of band channels: 4 Weight of press: 2,200 kg Power supply: 400 V / 50 Hz Power consumption: 4 kW Installation location: indoors / covered outdoors Noise level: under 80 dB(A) Year of manufacture: 2004 Baler rental possible. Cedpewqfnzofx Aaqohd

Condition: new, Year of construction: 2025, Attachment suited for: Lifting equipment Chjdpfoxrntmox Aaqsd

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: Codpfsu Tg I Dex Aaqohd The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, pressing force: 15 t, bale width: 700 mm, bale height: 700 mm, bale weight: 220 kg, input voltage: 400 V, power: 4 kW (5.44 HP), empty load weight: 2,700 kg, Manufacturer: Borg Baling Company Type: S-15KK Year of production: 2002 3x400V, 4kW, 14.5A Compression force: 15t Net weight: 2.7 t Chsdpfoh Dy Rfox Aaqod Bale max. sizes 700x700x1000 mm weight of a bale: ca 120 – 220kg Wide Range of Used Machinery, Industrial Equipment

Condition: used, functionality: fully functional, Year of construction: 2014, load capacity: 2,500 kg, empty load weight: 1,227 kg, total length: 1,500 mm, construction width: 1,130 mm, opening width: 1,860 mm, Cellulose/bale clamp Load center: 500 Cjdpou D S Tijfx Aaqehd ISO class: ISO class 3 = 2,500 - 4,999 kg Technical condition: very good Description: Rotation range 360° Opening range 560-1860 Arm height 900mm Arm length 1150mm

Condition: ready for operation (used), Year of construction: 2003, Baling press HSM 500.2 VL Fourfold wire bale tying Bale dimensions (L x W x H, mm): 1200 x 800 x 1000–1200 Bale weight (kg): approx. 500 kg Technical data (L x W x H, mm): 1213 x 1824 x 2987 Feed opening (mm): 1200 x 565 Cycle time (sec): 35 Pressing force (T): 54 Power supply (V): 400 (three-phase) Chjdpfxsra Ak Ej Aaqed Year of manufacture: 2002–2005, price: 3,400 EUR Baler HSM V Press 500.2 VL Year: 2006–2008, price: 3,600 EUR Transport height: 2600 mm

Condition: used, Year of construction: 1996, Binding type: twine binding | used Rollant 46 Twine binding hydraulic pick-up ready-to-use condition Codpfx Aajxpk T Djqohd

Condition: excellent (used), Year of construction: 2025, Year of manufacture: 2025 Csdpfx Aaoxlugteqehd

Condition: used, Technical data for the bale loosening drum: Manufacturer not known Type of bale loosening drum Year of manufacture not known Dimensions of the drum 6000 x 3000 mm (l x d) Csdpfju Thx Rjx Aaqshd Height of the welded-in helix 300 mm Dimensions of the drum frame 4900 x 3400 x 2200 mm (L x W x H) Drive power 2 x 4 kW Functional description: The bale loosening drum was fed with pressed paper bales from which the binding wire had previously been removed. The pressed and compact bale is broken up and loosened by the baffle plates welded into the drum parallel to the conveying direction. The helix, which is welded in with an incline to the conveying direction, transports the loosened material further to the drum outlet. Here it falls through a hopper onto a conveyor belt for further processing. Scope of delivery: Bale loosening drum Frame with drive and roller bearings for the bale loosening drum Comments: Documentation (operating instructions, CE declaration, electrical/hydrical circuit diagram) is not available and cannot be supplied. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: good (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t Chjdpoic Rl Djfx Aaqod The hydraulic unit is functional, the drive motor is in the removed state.

Condition: used, New: No Empty weight: 2 kg Part suitable for: trucks Type number: 7620370008 Occ ECU toll collect regeleenheid Bosch 7620370008 OEM : 7620370008 Cjdpfsxhxikox Aaqohd Article nr.: V155461004-veiling Used ECU toll collect control unit Bosch

Condition: good (used), Vertical baler Dixi 50S PET Cjdpfjv Amtkox Aaqjhd Year of manufacture: 2019-2021 Bale dimensions (L x W x H) (mm): 1200 x 800 x 800 - 1100 Bale weight (kg): approx. 350-500 kg Technical data (L x W x H) (mm): 1600 x 1300 x 3100 Filling opening (mm): 1200 x 670 Pressing force: 50 tons Power supply: 400 V

Year of construction: 2022, condition: new, Layout: Round bale grab Cedjn Tm Nkspfx Aaqehd Carrying capacity: 3.000 kg Attachment suited for: Agricultural machines Galen bale spear is produced to load your hay bales from 200 kg to 4000 kg from the ground to a trailer, truck, or stack them on your farm. As Galen we produce hay spear for telehandlers, tractor rear and front loaders, excavators and any other loaders that you requsted.

Condition: used, functionality: fully functional, Range of motion: 550–1700 mm Load capacity: 1600 kg Codpfx Aoxbga Rjaqjhd Grip plate size: 1000 x 1000 mm

Condition: good (used), Baler Hsm 155.1 vl Pressure force:, 18 tons, Unit pressure:, 2.33 kg/cm², Theoretical capacity:, 3 bales.h i.e. approx. 500kg/h Beam dimensions:, 1100x700x800 mm, Codpfx Aev Alaceaqohd Beam weight:, 150-250 kg, , Power supply:, 400 V/4 kW, ,

Condition: excellent (used), Technical data: Pressing force: 178 kN Drive power: 4 kW Cjdpfjv Akmzex Aaqshd Work cycle time: 23 s Loading height: 928 mm Loading opening width x height: 1195 x 558 mm Bale length x width x height: 1200 x 780 x 1000 mm Bale weight: 250 kg Machine width x depth x height: 1700 x 1075 x 2499 mm Machine weight: 1300 kg 4-fold with polyester tape Year 2010-2013

Condition: good (used), - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 Bale length: 1,100 mm Bale width: 750 mm Bale height: 750 mm Press length: 5,640 mm Codpfev Amv Esx Aaqshd Press width: 1,674 mm Press height: 2,500 mm Weight: 4,450 kg - Motor power in kW: 9 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2013 HSM HL 4010 LI baler - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 - Motor power in kW: 9.5 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2012