Recognised location: Ashburn (US) (Change)
Enter e-mail address
or
Move
6
pressure 650 t passage width 920 mm stroke 1750 mm Table area 2000x1500 mm ram surface 2000x1500 mm dayligth 2100 mm light-barrier hydraulic 203 bar closing speed 500 mm/sec pressing speed 0,5-10,4 mm/sec hole in plunger diameter/depth mm opening speed 250 mm/250 ejector return capacity 150 t total power requirement 75 kW L3jnj weight of the machine ca. 47 t dimensions of the machine ca. 4,4x2,5x7,5 m max pressure 250 bar 800 t impact shock dampening dissolution rate from 0.5 to 66.4... more
5
pressure 100 t stroke 620 mm surface of working table 800 x 700 mm dayligth 210 mm arm length 360 mm table height over floor 960 mm Gfu3va9 more
6
Pneumatic round table press Fabr.# Schüco type pneumatic 297 838 Fabr.# 1293, built in 1992 Technical data: force 35 kN maximum operating pressure 8 bar Height approx. 12 mm Intake opening approx. 134 mm Volume throughput approx. 400 strokes/h Ba7gnj9fsr External dimensions approx. 800 x 800 x 1400 mm maximum weight of 150 kg with: -many Schüco punching tools -Round plate -Base used, in good condition more
4
Vacuum press with applied membrane. Production year: 1997 Machine for coating pre-profiled carrier materials with thermoplastic films or other suitable plastic coating materials. 6 cylinder press Manufacturer: Henrich Wemhoner GmbH & Co Kg. A table driven by a hydraulic system. Table dimensions: 2800 - 1500 mm. Working temperature of the unit: 12 - 30 °C Upper heating plate: 0 - 180 °C Lower heating plate: 0 - 90 °C Film temperature: 0 - 180 °C Baxmwehell Pump Circulation pump type AOC 1201 AA ... more
6

REITZ EHSP100F4S

Biebergemünd Germany
6589 km
2013
showroom
Laboratory Press EHSP100F4S Table press with pressure 40 KN (4 tons), presses drive with worm gear screw jacks, gear 1:16, spindle diameter 45 mm, pitch 8 mm, spindle lift 0.5 mm per revolution, press button approx. 120 * 240 mm, height approx. 140 mm. Geared motor 0.75 KW, 1.500U/min., 4-pole, with spur gear i = 1:5. Speed 150 mm / min. maximum dynamic load of 40 kN. With change control, emergency stop and motor protection device. Sturdy steel frame of presses. Con8c89 Under table ma... more
6
1 hydraulic double stands press 400 to-neuwertiger TOP State - VIDEO Manufacturer: INO press - press technology Waiblingen Model/type 100 K-400 Built in 2000 Machine number 20445 The press has been reset by us on the Mint original condition. We have original overtaken the press, all wearing parts were replaced and checked. The press was 100% deep clean with dry steam cleaners and then original repainted light grey. The press has little operating hours after our determination.... more
6
pressure 1250 t table surface area 2000x1800 mm ram surface 1800x2000 mm stroke 1200 mm dayligth 2000 mm 0ugwugvr capacity of ejector in table t more
5
Baler (second-hand machine without warranty) type: HSM 75vl Technical data: Machine dimensions WxDxH: 1100x820x2150mm Filler Wxh: 900x600mm Bale size: 900x600x550mm Bale weight: 70-120 kg, depend on material Motor: 2 .2kW, 380V, 50 Hz Filling height: 600 mm Machine weight: 670 kg S8t0zdkp Year of construction: 1992 more
6
Mouldingpresse The MP / 3E is a hydraulic press for the production of Clayprofilen such as rubber seals, protective, decorative or chrome strips. By inserting an appropriate form template in the bolt head, almost any profile can be produced up to a diameter of 65 mm. Manufacturer: Wadhwa Type: MP / 3 p Year of construction: 1995 Temperature controller Speed controller Via a rotary control a stepless adjustment of the speed is possible Emsfeyftk heated sealing head The built-in heat... more
2
Pressing force 3.5 t Xs8moiocd Stroke 12 mm  134 mm intake opening Volume throughput 400 strokes / hour Air pressure 6-7 bar Air consumption 10 l / stroke Dimensions L x W x H 240 x 320 x 490 mm Weight 80 kg Siegfried Volz machine tools Rueschebrinkstr. 151-153 D-44143 Dortmund - Wambel more


Presses
every day

New machines via email!

Be informed!
6
Bieffebi press 30 ton Baeseknjjq Hand-operated hydraulic press with 30 tons of pressure Upper and lower plate heated to 210 ° C, separate temperature setting Table size 300 * 400 mm Slide plate For the manufacture of printing scenes or vulcanization of rubber parts more
5
Vulcanizing press Fabr.Wickert type: WKP 600/3/3/RZ BJ. 1990 Ltgwz Control SieMatic 100U Mounting surfaces can be heated. Druchgangs width: 400mm Height: 450 mm Press Max pressure: 300 bar more
5
Nearly-new. It only worked 3 months. For highly plastic materials such as rubber, melamine, urea, bakelite, powder, foam, etc. Technical specifications: With 2 compression molding presses Wkjh7i8qg Clamping force: 700t Plate size: 1200 x 1200 mm. Piston diameter: 660 mm. Closing stroke: 760 mm. Space between tie bar: 1360 x 800 mm. Pump pressure: 210 kg / cm2 Heating: 85.8 kW Oil hydraulic system: 25 x 2 hp Oil tank capacity: 920 l. Voltage & Frequency: 380 v - 50 ... more
1
1 Vollgekapselte frame press with press room extraction Manufacturer EP K 400-2 Pressing force 4000 KN Mdqsp 2400 x 1600 mm The press is under current sightseeing by appointment, Caution If you are looking for up to 10000 kn presses in terms of non-metallic Modification / modification according to customer-specific information and Erfodernissen z.b new machines / upper piston presses like to contact with our press specialist more
5
The machine, there is no documentation as instruction manual plans etc. The machine is ready for demonstration. Without accident prevention Regulations or UVV documents. The press should be rebuilt as a mounting press. Which is why I have two n e u e C-form-press frames here. See our offer of R 766. I could both for EUR 600.-leave. This shows a picture (the fifth). P0jmsrum -Type 50-200 B1, HY-CUM -with Bosch-hydraulic cylinder, engine 1, 5kW, 1.430 U/Min. -Stroke 200mm, - throat dept... more
4

Rolling punch illig ZSM 90

Hardthausen-Lampoldshausen Germany
6643 km
1970
used
Very nice rolling punch completely overhauled and lined roller table with lateral VA sheets and rebuilt. Ask us, we have more than 70 machines Illig Illig the world's largest offering of stock, we are a machinery dealer and service and spare parts. ZSM 60 and UA 225, the complete program Illig Tso9wi7wr more
6
Electrical Laboratory Press EHSP100F Laboratory heating press with pressure 40 KN (4 tons), 1:16, spindle diameter 45 mm, pitch 8 mm, spindle lift 0.5 mm per revolution. Geared motor 0.75 KW, 1.500 rpm, 4-pole, with spur gear i = 1:5. Speed 150 mm / min. maximum dynamic load of 40 kN. With change control, emergency stop and motor protection device. Vlxdedzoc Table 700 * 700 mm, pressing area approximately 100 * 200 mm, height approx. 140 mm. Under table made of high-quality alumini... more
4
Pneumatikpresse.li.Weite zw.den columns ca.160mmSäulen Durchm.24 / 25mm tabletop Ti.100xBr.125mm Festo cylinder outer Durchm.ca 90mm dimension Br.650mmxTi.400mmxHö.340mm pneumatischde Zweihandsteürung .It is a pure Pneumatiksteürung Y9la9zxr more
5
Plate press - table press - bonding press - Laboratory Press - forming - Universal Press MHSP522 Press area 230 * 230 mm Clear width 200 mm Manual drive with worm gear screw jacks 5 KN Pressure 5 KN (0.5 tons) Weight 55 kg Per sensor revolution 0.5 mm path, this little manual force with great force, very fine deliverable. Pressing force is long maintained by self-locking. Mpb29 more
4
Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 * 220 mm -Maximum pressing force at 220 * 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor My38z -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, ... more
6
Electrical plate press / glue press EHSP522 press area 200 * 200 mm Print 5 KN / 0.5 tons Suitable for plates bonding, embossing, for punching with steel strip cuts 2snhtkpuo On request with: -Heating and temperature control -Load cells and measuring indicators for use as test press more
3
Screw jacks forecasts RN 100TBTMDR1 / 32-1300P Classic screw jacks with 260 KN thrust dynamic at 300 rpm. Static load 1000 KN. Reduction i = 1:32 spindle diameter 100 mm, spindle pitch 16 mm, 1300 mm Spindle, with head plate, double-sided shaft input, d = 50 mm with motor flange on one side, d = 300 mm. With thermowell. Weight about 400 kg. The screw jack is used. Nx0gxzqz more
5
Electrical plate press / glue press 0.5 tons 2lb9rfppc Press area 200 * 630 mm Print 5 KN / 0.5 tons Suitable for plates bonding, embossing, for punching with steel strip cuts the spindle is self-locking and thus keeps the press force over time. 2 PCs in stock For an additional charge:-Heating, insulation plate and temperature control up to 220 ° C for use as a heat press. -Force measuring device to use as a test press. more
6
Electrical plate press EHSP5033 For testing and forming purposes with extremely slow speed of 130 mm / minute and pressure of 2.3 tons. Through the self-locking with long-term retention forces. 2w2zxz0c0 Presses drive worm gear screw jacks RNF040-DT MDR 1/28-600 p for pressure 23 KN with gear motor 0.37 KW, i = 1: 10.5. Usable table and pressing plate area 300 * 300 mm. clearance height 300 mm. Reversing contactor control with dead-man's control, emergency stop, and main switch. ... more
1
* Unused FAIR & AUSSTELLUNGSGERAET **** DEVICE IS TECHNICALLY AND OPTICAL 100% PERFECTLY and / or. absolutely MINT **** UNIVERSAL membrane-& Vacuum press with heating and molding station for all thermoplastic materials such as: - Solid Surface Materials: CORIAN, STARON, LG - Himacs, PLEXICOR, WILSONART, AVONITE - Plastics: ABS, PMMA (acrylic glass), PET-G (Vivak), PS, PP, PVC, PC (Makrolon) * heating station: Usable area: approx 2550 x 1150 mm Table starch, adjustable 0 - 70 mm Heating power: 9 ... more
2
* Absolutely good as new Demonstration & AUSSTELLUNGSGERAET * *** device is refurbished and truly 100% perfect and / or. ! Absolutely mint *** === COMBIMAT combines 3D films vacuum press MULTIMAT and the heating station COMBITHERM & lt; === * All in one THERMOPRESS CENTRE: - wide range of applications of membrane press by ingenious machine combination: heating Forming Formverleimen form veneers 3D film coating - universal and multifunctional vacuum press for 3D-film coating, Schichtverleimen and... more


Presses
every day

New machines via email!

Be informed!

to

to

Change search

SELL IMMEDIATELY
on Europe's market leader for as little as € 0,79 per ad.
Find out more now


Phone: +44 (0) 20 806 810 84
or sell immediately
Try our Machineseeker app now!
Machineseeker app for iPhone and Android.
Want to really stop the chat history?
Yes No
×
Machine Finder chat
Name E-mail Your message to the Dealer
START CHAT WITH DEALER
  You are chatting with: 
  Your contact person: 
  
Your contact is typing
SEND MESSAGE
  You are chatting with: 
  Your contact person: 
  
Your contact seems to be inactive
Chat window close