Used Book-Press for sale (12,427)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm Dedpfx Anjx A U Ncowsut • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm Dedpfx Anotx E Rqsweut ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: good (used), Code: 0378 Brand: ORMAMACCHINE Model: NPC 6/90 E - Norme CE Hot press with electric platens for veneering, panels, furniture, custom-made furnishings, wooden doors, kitchens, bathroom furniture, composite materials, plastics, and various - CE Standard Technical data: Platen dimensions 2500 x 1300 mm Total thrust 90 tons N° 6 cylinders Cylinder diameter 70 mm Stroke 400 mm Pressure 3 kg/cm² Motor 2 Hp Electric Platens: Max temperature up to 120° C, max working pressure 7 kg/cm². Platen made of a 12 mm aluminium plate which resistances are inserted in underneath a chipboard support with reinforcement tubes inside Perimeter emergency rope Double rack system Lateral guides on platens for a perfect movement further safety feature of the pressing platen Overall dimensions mm 3060 x 1650 x 1850 h Weight kg 3400 Dusdpfsy I Tqrjx Anwot

Condition: good (used), Code: 0377 Brand: COLOMBO R Model: PCA.S Automatic continuous-cycle hot-pressing line for the production of panels, furniture, doors, paneling, sandwich panels, and various Sturdy supporting structure Composition: Duodpfjy I Sncjx Anwot 4-roll gluing machine OMMA- Width 1400 mm Disc transfer conveyor Preparation table Press COLOMBO 5500 x 1400 mm - n° 8 pistons - diameter 150 Solid steel platen Top-down pressing Pressure 4 kg/cm² Automatic unloading with photocell devices Work surface height 800 mm Closing times are reduced to 1–2 seconds and opening times to 2–3 seconds Overall dimensions press mm 5960 x 1900 x 2320 h Complete line length 22 mt Installation of the line does not require any foundation

Year of construction: 2023, condition: used, Pressing force 53 t stroke 300 mm Duodpfx Ansy H Rahswjt control Siemens Pneumatic system pressure 6 bar Maximum supply pressure of the pneumatic system 10 bar Pressure in the hydraulic system 255 bar Dimensions (HxWxD) 3.200 x 2.500 x 2.350 mm weight 8.000 kg In our assessment, the bushing press is in like-new condition. Technical features: - Bushing pressing including plastic deformation - TOX pneumatic-hydraulic actuator with 53t pressing force at 6 bar - 300mm stroke - Siemens control Accessories, tools, and clamping devices shown are only included if specifically stated in the additional information. Technical data and specifications are subject to change without notice. Prior sale is reserved.

Condition: good (used), Year of construction: 2012, functionality: fully functional, power: 18.5 kW (25.15 HP), input voltage: 400 V, input current: 37 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 175 t, stroke length: 265 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table width: 104 mm, table length: 3,700 mm, table height: 900 mm, throat depth: 410 mm, clearance between the columns: 3,100 mm, oil tank capacity: 250 l, total length: 5,300 mm, total width: 2,700 mm, total height: 2,750 mm, overall weight: 13,100 kg, Equipment: CE marking, safety light barrier, 2012 Durma AD-R 37175 CNC Press Brake – 175 Ton x 3700mm | CNC Advantage Control | Tooling Included Used 2012 Durma AD-R 37175 CNC press brake for sale. 175 ton, 3700mm, CNC Advantage control, tooling included. Manufacturer: Durma Model: AD-R 37175 CNC Pressbrake Control: Durma CNC Advantage Control Year: 2012 Capacity: 3.7m x 175T Condition: Good Description 2012 Durma AD-R 37175 CNC Press Brake – a high-performance, precision hydraulic press brake designed for efficient and accurate sheet metal bending. This machine offers excellent value for workshops looking for a reliable 175 Ton CNC press brake with strong capabilities and proven Durma build quality. Manufactured by Durmazlar (Durma), a globally recognised leader in sheet metal machinery, the AD-R series is known for robust construction, ease of use, and excellent performance-to-price ratio. 🔧 Key Features 175 Ton Bending Capacity 3700mm Bending Length Durma CNC Advantage Control (2D Graphic Programming) 3 Axis Machine (Y1, Y2, X – Powered) Djdpfjy Ir D Dox Anwsut Manual R-Axis via Backgauge Fingers Motorised Backgauge with Linear Guides & Ball Screw System European Style Clamping System Full Set of Top & Bottom Tooling Included Top Tool Hangers Included (Supplied, not shown in photos ⚙️ Technical Specifications Bending Force: 175 Ton Bending Length: 3700 mm Distance Between Columns: 3100 mm Stroke: 265 mm Daylight: 530 mm Throat Depth: 410 mm Table Width: 104 mm Table Height: 900 mm Speeds Y Rapid Feed: 120 mm/sec Working Speed: 10 mm/sec Return Speed: 100 mm/sec Backgauge X Axis Travel: 650 mm X Axis Speed: 500 mm/sec Backgauge Fingers: 2 (height adjustable) General Motor Power: 18.5 kW Oil Tank Capacity: 250 Litres Dimensions (L x W x H): 5300 x 2700 x 2750 mm Weight: 13,100 kg 💡 Machine Overview The Durma AD-R series is engineered for precision bending, low maintenance costs, and long-term reliability, making it an ideal solution for fabrication shops and industrial production environments. With a large daylight opening, generous stroke, and rigid frame construction, this machine is well suited for handling a wide range of sheet metal applications, from light fabrication to heavy-duty bending work. The CNC Advantage Control system provides: 2D graphical programming Automatic bend sequencing Easy part calculation USB program storage and backup User-friendly interface for fast setup and operation 🏭 Why Buy This Machine? Excellent price-to-performance CNC press brake Strong European build quality Ideal for steel fabrication, sheet metal workshops, engineering firms Complete with tooling – ready to go to work Reliable and simple CNC control – easy for operators 📦 Included with Machine Full Top & Bottom Tooling Set Top Tool Hangers (supplied) Sliding Support Arms Backgauge System Notes: *Specifications are given in good faith but not guaranteed*

Condition: good (used), Leonhard Kurz Model H Book Edge Gilding Machine This machine is in very good condition and ready to use. This machine is from the popular Leonhard Kurz manufacturer, manufactured in Germany. Dujdpey N Dxcofx Anwst Description This edge gilder is suitable for books, cards, invitations, and business cards. Hand-operated clamp, powered by only 230V. A powerful clamp with adjustable pressure ensures repeatability. The machine features a convenient material clamp, depth adjustment, and a convenient base with wheels. Specifications: Mechanical clamping mechanism Power consumption: 170W Power supply: 230V Machine weight: 80kg

Condition: good (used), Nagel Citoborma 280B Paper Drill This machine is 100% functional. It is one of the newest models. The drill table is adjustable in all directions (sides, front/back). It has stops for setting the drilling spacing. Dsdpfjy Nzi Ejx Anwout The installed table is an enlarged version. Additionally, the paper drill has an automatic table lock that releases after each cycle. Excellent condition. Solid construction – weight 76 kg. 380V power supply Two drilling heads with adjustable spacing from 45-120 mm. Drill diameter 2-20 mm. Stack height 60 mm. The machine has been serviced. Includes drills and tools, a new cutting stick, and an instruction manual.

Condition: good (used), Stago PB 2015 Paper Drill This is the latest drill from Stago, originally from the office of a large company. The machine is 100% functional. The drill table is adjustable in all directions (sides, front/back). It has stops for setting the drilling spacing. The installed table is an enlarged version. Additionally, the drill has an automatic table lock. Sturdy construction – weighs approximately 70 kg. 230V power supply Two drilling heads. Drill diameter: 2-10 mm. Stack height: 60 mm. The machine has an adjustable spacing between the heads. The drill has been serviced. Drills and tools are included. Dodpfx Anjy Nzixjwjut

Condition: excellent (used), Year of construction: 1991, Hydraulic veneer press with electric heating plates Under-piston design BUSSE electric heating plates Central control panel with all operating elements Analog temperature display for both heating plates Pressing pressure infinitely adjustable via pressure switch Main switch Two-stage hydraulic pump with automatic changeover valve from low to high pressure Safety pull cord Rack compensation CE conformity Dedjyyn Rdspfx Anweut Pressing area: 2,500 x 1,300 mm Number of press cylinders: 4 Total pressing force: 90 t Stroke height: 400 mm Operating voltage: 3 x 400 V + N, 50 Hz Total connected load: approx. 20.3 kW Space requirement (L x W x H) approx.: 2,900 x 1,250 x 1,900 mm Weight: approx. 3,800 kg Request more information NEW MYLAR FILM on both heating plates NEW hydraulic cylinder seals Used machinery notice: • Technical data subject to errors and prior sale. • Prices quoted are ex works – free loaded! • The machine has been cleaned and function-tested. • All machines are sold as inspected, without any warranty claims. Buyers are welcome to inspect the machines at their location. • Special agreements are only valid in written form. (Your inquiries will only be answered with your address and telephone number!)

Condition: excellent (used), MAWEG Gluing Press Machine frame inclined at 10 degrees Single-sided loading Horizontal beam with manually adjustable height via hand crank (all clamping cylinders can be adjusted together) Hydraulic cylinders with quick clamping function, infinitely adjustable Manual hydraulic cylinder clamping Dusdpfx Ajyyn E Uenwst Pressing force per hydraulic cylinder approx. 2000 kp Hydraulic cylinder stroke 100 mm Clamping depth 100 mm Maximum clamping length: 2800 mm Maximum clamping height: 1800 mm 4 vertical pressing cylinders 2 horizontal pressing cylinders 6 counter-stops Note on used machines: • Errors in technical specifications and prior sale excepted. • Prices quoted are ex-location and are pick-up prices – loading included! • The machines have been cleaned and function tested. • All machines are purchased as seen, without any warranty claims. Buyers are welcome to inspect machines on site. • Special agreements are only valid in written form. (We only respond to inquiries that include your address and telephone number!)

Condition: excellent (used), Year of construction: 1993, OTT Model JU 2513 Hydraulic veneer press with electric heating plates Under-piston design BUSSE electric heating plates Central control panel with all operating elements Analog temperature display for both heating plates Pressing pressure infinitely adjustable via pressure switch device Main switch Two-stage hydraulic pump with automatic switching valve from low to high pressure Emergency safety pull cord Rack compensation Djdpfjxgpaqjx Anweut Stroke limitation CE compliant Press area: 2500 x 1300 mm Number of press cylinders: 4 Total pressing force: 70 t Operating voltage: 3 x 400 V + N, 50 Hz Total connected load: approx. 20.3 kW Required space (L x W x H): approx. 2900 x 1250 x 1900 mm Weight: approx. 3200 kg

Condition: good (used), Year of construction: 1989, Pressing area 2550 x 1350 mm Number of press cylinders #6 Total pressing force 140 t Opening width approx. 400 mm Operating voltage: 3 x 400 V + N, 50 Hz. Total connected load approx. 26 kW Space requirement (L x W x H) approx.: 3400 x 1600 x 2000 mm Weight: approx. 5500 kg Dusdpfxswd N Rmo Anwst Hydraulic hot plate press Down-piston design Electric hot platens Pressing pressure continuously adjustable via pressure switch Hydraulic pump Central control panel with all operating and Digital temperature display for both hot platens Press cycle counter Safety ripcord Rack compensation Main switch Note for used machines: • Errors in technical specifications and subject to prior sale. • Subject to change without notice. • Prices quoted are for pickup from the location - free shipping! • The machines have been cleaned and functionally tested. • All machines are sold as seen, without any warranty. The buyer is free to inspect the machines on site. • Special agreements are only possible in writing. (We will only respond to inquiries if you provide your address and telephone number!)

Condition: new, Technische Daten: Abmessungen der Heizplatten 3000 x 1300 mm Anzahl der Heizplatten 2 # Anzahl der Presszylinder 6 # Pressdruck 90 t (900 kN) Zylinderdurchmesser 70 mm Anzahl der Etagen 1 # Etagenöffnung ca. 400 mm Anschlussleistung ca. 21,0 kW ELEKTRISCH BEHEIZBARE TISCHE (ELKOM - Deutschland) Der Tisch besteht aus 2 kalibrierten Aluminiumplatten, in denen die elektrischen Widerstände verlegt sind. Die maximale Betriebstemperatur ist 120 Grad C. Im am Tisch wird eine Dämmplatte montiert, die zur Wärmeisolierung gegenüber der Presse dient. Der Bau des Tisches und die präzise Verarbeitung, die von spezialisierten Firmen vorgenommen werden, gewährleisten eine sehr gleichmäßige Verteilung der Dodpfx Anefh Tmmsweut Temperatur. Die Heizplatten sind mit speziellen Halterungen an der Presse befestigt um die Wärmeausdehnung zu erlauben, außerdem erleichtern sie die Wartung und das Auswechseln. Spezifischer Betriebsdruck des Tisches bis zu 10 kg/cm2 Max. Temperatur der Heizplatte 120 Grad C Arbeitstemperatur 90 Grad C Schuetzsteuerung Waermeschutzschalter Die Zylinder sind aus spezial geschweissten und gross dimensionierten Stahlrohren hergestellt. Hydraulik: Kompakte hydraulische Einheit Fabrikat HAWE aus Deutschland. Pumpe fuer Schliessphase und Druckaufbauphase. Automatische Nachdruckverstellung Leistung der hydraulischen Einheit 3 kW Bewegung des Presstisch von unten nach oben. Pressengestell: Das Pressengestell besteht aus einer schweren verwindungssteifen und spannungsfrei geschweissten Stahlkonstruktion. Beide Presstische sind aus HEA-Profilen geschweisst. Die Bearbeitung der Baugruppen erfolgt auf CNC-Barbeitungsmaschinen. Bewegung des Presstisches mit Zahnstangen und Parallelfuehrung an 2 Ecken des Presstisches aus selbstschmierenden Material. BEDIENTAFEL mit Display und Tastatur: Bedientafel Siemens mit 7-Zoll-Farb-Touchscreen mit Verbindung zum Ethernet- Netzwerk für den Fernwartungsservice. Das System ist mit einer eigenen Software ausgestattet durch die die Bedienung der Presse einfach und intuitiv erfolgen kann. Sie können folgende Parameter programmieren, abrufen und ändern: - Automatische Regelung des hydraulischen Drucks aufgrund des Werkstückgrösse und des gewünschten spezifischen Drucks. Das System reguliert den Druck der Zylinder automatisch und der Bediener muss keine Berechnungen mit Grafiken oder Tabellen anstellen. - Möglichkeit zum Speichern von bis zu 100 Arbeitsrezepten (Temperatur, spezifischer Druck, Pressdauer, Plattengrösse). - Direkteinstellung des hydraulischen Drucks der Zylinder mit digitaler Kontrolle aufgrund der Grafik. Dieses System kann alternativ zur automatischen Regulierung verwendet werden, falls Sie lieber mit der herkömmlichen Methode arbeiten. - Elektronische Regelung der Pressdauer - Elektronische Kontrolle der Temperatur der Tische - Automatische Wiederherstellung des Drucks aufgrund des Nachgebens des Materials. - Komplette Diagnostik und Störungsanzeige mit Meldungen am Display. WEITERE AUSSTATTUNG UND MERKMALE DER PRESSE Haken zum Anheben der Maschine um das Laden/ Entladen der Maschine beim Transport zu erleichtern. Nivelliervorrichtungen die an den Füssen der Presse montiert sind. In die Presse integrierte Schalttafel; dadurch sind weniger Aussenkabel notwendig, die vorhandenen sind jedoch auf jeden Fall angemessen geschützt. inkl. Option: Fehlbelegungsüberwachung (Ebenheitskontrolle)

Condition: used, Year of construction: 2009, Extraction diameter: 250 mm Rated volumetric flow: 3534 m³/h Filter area: 22.6 m² Motor: 5.5 kW Briquetting: throughput approx.: 30 kg/h Briquette diameter: 65 mm Motor: 3.0 kW Storage location: Nattheim Dedpfx Anjyym A Sswjut

Condition: used, Year of construction: 2020, functionality: fully functional, For sale: Metal Stamping Press ALP-25C (25T, 2020) Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25C Year of manufacture: 2020-11 A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping various metal parts. Technical specifications: Nominal capacity: 25 T Stroke: 45 mm Stroke rate: 145 strokes/min (SPM) Max. die height: 180 mm Height adjustment: 35 mm Ram working area: 170 × 150 mm Bolster area: 370 × 240 mm Country of origin: China Applications: The ALP-25C press is suitable for: stamping, cutting, bending, and forming metal parts; small pressing operations in tool, metal structure, and automotive parts manufacturing; working with thin and medium-gauge sheet metal. Dusdpfxjxmwnie Anwet If you have any further questions, please feel free to contact us.

Condition: new, Year of construction: 2021, functionality: fully functional, For sale: Metal Stamping Press JINAOLAN ALP-25V (25T, 2021) Condition: Brand new, never used, original packaging. We use several of these presses in our factory—photos show those units. Two brand new units available. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25V Dsdexniw Sopfx Anwjut Year of Manufacture: 2021 Modern CNC-controlled eccentric press designed for forming, stamping, and punching various metal components. The press is equipped with a high-level operator safety system (Laser Safe), ensuring maximum operational safety. Technical Specifications: - Rated Capacity: 25 tons - Stroke Rate: 60–140 strokes/min (SPM) - Stroke Length: 60 mm - Max Die Height: 200 mm - Die Height Adjustment: 50 mm - Slide Area: 470 × 245 mm - Bolster Area: 680 × 300 mm - Main Motor: 2.2 × 4 kW - Max Air Pressure: 0.51 MPa - Max Tool Weight: 0.30 t - Control: CNC (programmable control unit) - Safety System: Laser Safe – two-hand control system Application: This press is suitable for stamping, punching, bending, and forming metal parts. Thanks to CNC control and precision mechanics, the machine ensures high productivity, repeatability, and safety. Ideal for small and medium-sized manufacturing, metal component, and forming part production. Advantages: - Completely new, factory-sealed equipment - CNC control: precise and user-friendly programming - Laser Safe system: press can be lowered only when both hand controls are activated (two-hand safety) - Reduces risk of injury, complies with stringent safety standards - Robust construction and stable eccentric drive - 2 brand new presses in stock + several used units in operation If you have further questions, we are happy to answer them.

Year of construction: 2021, condition: excellent (used), For sale: Metal Stamping Press ALP-25J (25T, 2021) Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25J Year of manufacture: 2021-04 A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping a wide range of metal components. Technical specifications: Nominal capacity: 25 T Stroke: 100 mm Stroke rate: 100 strokes/min (SPM) Duedpjxm U S Sjfx Anwst Max. die height: 260 mm Height adjustment: 55 mm Ram working area: 560 × 370 mm Bolster area: 250 × 220 mm Country of origin: China Applications: The ALP-25J press is suitable for: - Stamping, cutting, bending, and forming metal components - Small press operations in tool, metal structure, and automotive part manufacturing - Working with thin and medium-thickness sheet metal If you have any further questions, we will be happy to answer them.

Condition: excellent (used), Year of construction: 2014, Hydraulic Press Bunorm 4S-500 Manufacturer: Bunorm AG Model: 4S-500 Year of Manufacture: 2014 Pressing Force: 500 kN Maximum Pressure: 225 bar Weight: 3,200 kg Electrical Connection: 3×400 V + N + PE Frequency: 50 Hz Protection: 20 A Control System: Siemens Simatic HMI Touch Safety System: SICK C4000 Light Curtain SCOPE OF DELIVERY Includes, among others (non-exhaustive list): Hydraulic Press Bunorm 4S-500 Exact scope of delivery as shown in the photo series. The Bunorm 4S-500 hydraulic press impresses with its robust construction and a pressing force of 500 kN at a maximum pressure of 225 bar. With its solid build and a weight of 3,200 kg, the press is suitable for demanding production applications. The integrated Siemens Simatic HMI Touch control system enables precise and user-friendly operation. Thanks to the modern SICK C4000 light curtain safety system, a high level of operator protection is ensured. This machine is the ideal solution for companies that value reliability, precision, and safety. No guarantee is given for the correctness, completeness, or currentness of the information provided. Djdpfxsxfl Axo Anweut

Year of construction: 2013, condition: excellent (used), 1. SCOPE OF SERVICES - EBU H 12 FT Eccentric press - Siegfried SPC control unit 2. DOCUMENTATION - Complete operating documentation available 3. TECHNICAL DATA Year of construction: 2013 Type: Eccentric press Nominal force: 120 kN Max. mould installation height: 170 mm Max. weight of upper mould part: 25 kg stroke adjustment range: 30 mm ram height adjustment: 40 mm Stroke rates: 40-200 1/min Pneumatic operating pressure: 5.5/10 min/max bar Dodpfx Ansfrzlmswout Electrical connection: 400 VAC, 50 Hz Weight: 1200 kg

Condition: excellent (used), Year of construction: 2013, Vacuum Press, Vacuum Table, Joos Vacuum Table with Silicone Membrane Universally applicable press, veneer press for veneering, coating, form bonding, form veneering, edge gluing, etc. With this press, you can generally do without a hydraulic veneer press, though with some limitations. New heat-resistant silicone membrane, extremely elastic and easy to clean. Also suitable for the molding of preheated thermoplastic materials such as acrylic glass or solid surface materials. Frame inner dimensions approx. 2900 x 1410mm, usable surface approx. 2800 x 1300mm Working height approx. 900mm Vacuum pump Becker VT4.40, 400V, 1.5 kW with 40 m³/h output, and two vacuum tanks of 200 liters each, allowing comfortable operation and rapid evacuation. Electronic vacuum pressure switch, so the pump switches off when the required vacuum is reached and does not run continuously Mobile on four swivel castors, lockable Frame can be easily folded up, secured with two catches Double frame for quick membrane changes Currently fitted with a new silicone membrane Rapid vacuum distribution thanks to grooved base plate CE mark Dodsy Hl Hpepfx Anweut Original paintwork, some areas retouched Both the silicone membrane and base plate have been renewed; the machine is ready for immediate operation. Dimensions approx. 3100 x 1550 x 1020mm (LxWxH). Weight approx. 550kg. The machine can be demonstrated at our site by appointment. We only offer machines that are ready for demonstration in our warehouse – see “Further offers from this supplier.”

Condition: new, pressure 180 t stroke 400 mm column daylight 1500 mm Frame Width 550 mm distance spindle /table max. 1000 mm total power requirement 7,5 kW Front light range 1550 mm Lateral light range 550 mm weight of the machine ca. 2100 kg dimensions of the machine ca. 2300x1200x2850 mm Domestic equipments: - Stable welded construction - Pressure cylinder laterally adjustable - Electric control via lever / manual over hand lever - Pressure gauge via pressure gauge - Material supports per cylinder in the height adjustable - CE mark Dodpfoyv I S Hjx Anweut

Year of construction: 2023, condition: used, Used machine Dedpjyf R Alefx Anwjut Year of manufacture: 2023 Equipment and technical data: - Machine frame: robust, torsion-resistant steel construction - Membrane frame: opening/closing with gas pressure cylinders - Swivel castors: removable, 360° rotatable - Vacuum pressing pressure: 0.85 kg/cm² (8.5 t/m²) - Vacuum table: 3.68 m²; 31.28 t - Membrane: natural rubber 3100 x 1500 mm - Usable area: 2920 x 1320 mm - Material thickness: 2 mm - Colour: grey - Material hardness: 53 Shore A - Tear strength: 26 MPa - Elongation at break: 690% - Temperature resistance: up to +130°C - Pressing area: 2920 x 1320 mm - Power requirement: 1.25 kW Options: - Membrane quick-change system - 200 l tank with digital pressure control, operating modes: automatic and manual - Additional vacuum outlet for further applications: vacuum bag, vacuum clamps - Becker pump 40 m³/h Dimensions: 3200 x 1400 x 1000 mm Availability: short notice Location: 63934 Röllbach

Condition: good (used), functionality: fully functional, Press Brake Brand: AMADA Model: HFT 80/25 Capacity: 2500 x 80T 4 axes Distance between uprights: 1800 mm Dimensions: 3500 x 1500 x 2100 mm Dusdpfx Aewivddonwst Weight: 6,500 kg Equipped with new and used tooling

Condition: reconditioned (used), functionality: fully functional, stroke length: 105 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table height: 970 mm, throat depth: 200 mm, total length: 1,420 mm, total width: 1,100 mm, total height: 1,800 mm, overall weight: 2,800 kg, working width: 60 mm, back gauge: 345 mm, control type: manual, actuation type: hydraulic, Press Brake Brand: PROMECAM Duedpoxwukcofx Anwet Model: PPH25.12B Capacity: 1200 x 25T Distance between uprights: 1020 mm Throat depth: 200 mm