Used Cold Water for sale (7,608)

Condition: used, Length: ca. 2.6 m Width: ca. 1.7 m Height: ca. 2.3 m Codsw Tmllopfx Anwjrb Features: Cooling unit (Technobloc, type: ACN050U, output: 0.7 kW, refrigerant: R404a)

Condition: used, Year of construction: 2015, Electronically controlled dual system for softening particle-free water. With two pressurised tanks made of GRP. Freely adjustable cycles with time or quantity-controlled regeneration. With brine tank. Additional title: Double system with GRP tanks, Softening with a resin ion exchanger Operating pressure: 8 bar Operating temperature: 40 °C Codpfow U D S Eox Anwerb Voltage: 230 V Frequency: 50 Hz Material: vessels from GFK Features: Pre-filter, valve block, water meter, 2 x GRP tanks, various hoses

Year of construction: 2001, condition: used, The Pall CFS system is designed as a single unit and can be installed directly in front of the filling line without the need for a buffer system. It is a completely independent process unit consisting of the following components: filter vessel Piping and connections Membrane cleaning system (CIP) integrity check Switchboard The hygienic design, the simple integrity test and the full automation ensure the microbiological safety of the system and usually allow the operation of the filling staff. Cluster filtering groups filter elements into clusters. Each cluster has its own outlet valve. During filtration, all clusters are open. Cleaning, sterilization and integrity testing are performed per cluster. Advantages of the CFS principle; Longer life Integrity testing on site Integrity diagnostics per cluster Special rinsing High specific flow rate Short flush times Constant flow in all candles Minimal water consumption Quick replacement of filter elements Controlled backwash Minimal beer loss High biological safety Constant availability With this filter system only preclarified products may be filtered, which have normally filterable properties in their composition. Max. filtration flow: 400 hl/h continuous Permissible operating pressure: 6 bar Permissible operating temperature: 105 °C Volume: 1456 l Current: 10 A Voltage: 220 V Water: cold water: min. 150 hl/h; hot water (max 65 ° C): min. 150 hl/h Compressed air: prepared compressed air: 4 - 6 bar; control air: 5 - 8 bar Length: 1,40 m Width: 1,20 m Height: 1,85 m Weight: 3450 kg Crsdpfx Anevcqx Deweb Base construction: basic frame with control and measuring components and filter container; cleaning module Features: 98 filter cartridges, 3 piston diaphragm pumps (Dosage), centrifugal pump with frequency converter (WT circuit), various analog and digital sensors (flow, pressure, level, temperature, conductance), various valves, control cabinet

Year of construction: 2015, condition: used, Waste water neutralisation Capacity: 8 m3/h Credoxbqr Djpfx Anwsb Operation / Control: Control cabinet with touch-screen display / WAGO Features: Neutralisation vessel (37 hl); final control vessel (4,5 hl); caustic vessel; acid vessel; pumps; process measurement, instrumentation and control technology; control cabinet

Condition: used, Year of construction: 1998, Additional title: reverse osmosis plant Capacity: 6 m³/h Crsdpfx Anjw U A Uroweb Length: 3,7 m Width: 0,85 m Height: 2,1 m Weight: 1000 kg Features: Reverse osmosis system, scale saturation tank, permeate tank, HMP dosing, milk of lime preparation station, various pumps, valves and measuring probes

Condition: used, Year of construction: 1994, Three-stage water degassing system for water degassing and CO2 impregnation. The raw water enters the first degassing tank through an injector nozzle. The high flow velocity causes oxygen and nitrogen to be torn out of the water jet and escape from the top of the tank. This process is repeated in the second degassing tank. In the third tank (impregnation tank), after entering through the injector nozzle, the water is mixed with the CO2 pressure in the upper part of the tank, which is under impregnation pressure. Crjdsxzqt Ispfx Anwsb Additional title: multi-stage cold deaeration with impregnation Base construction: mounted on stainless steel frame Features: 3 containers (each with pressure gauge); 3 centrifugal pumps; control cabinet with control panel; pipes with various fittings

Condition: used, Additional title: with automatic regeneration Nominal flow: 9800 l/h Pressure working area: 6 bar pressure class: 8,5 bar Operating temperature: 25 °C Ambient temperature: 35 °C Current: 0,35 A Voltage: 230 V Frequency: 50 Hz Weight: 390 kg Features: 2 x softening tanks (resin-filled); brine tank; valves and pipes Crodsw Tbunopfx Anwob

Condition: used, Vertical hot water tank with internal heating coil for heating with steam. Capacity approx. 30 hl. Additional title: Heatable tank Content approx.: 3000 l Width: 1400 mm Height: 2800 mm Material: stainless steel Position: free standing Base construction: Cylindrical tank on pipe feet Features: 1 tank with heating device, temperature gauge, outlet in the centre of the base, manhole at the top, overflow Cedpew Tdx Ajfx Anworb

Condition: excellent (used), CTS Temperature Shock Test Chamber TSS-70/350-A Device Data Manufacturer: CTS GmbH Model: TSS-70/350-A Year of manufacture: 10/2017 Version: Temperature Shock Test Chamber Cooling unit: Water-cooled Description Used temperature shock test chamber by CTS. Suitable for shock and temperature cycling tests. For use in industry, research, and quality assurance. Areas of Application - Material testing - Aging tests - Electronics and component testing - Temperature shock tests - Automotive and QA Temperature Ranges Hot chamber: +50 °C to +220 °C Cold chamber: -70 °C to +100 °C Electrical Data Crodpfxoy H Hk Ao Anwob 400 V / 3/N / 50 Hz Power: 19.8 kW Current: 46.5 A Connection: CEE 63A Refrigeration System Precooling: R452A, 7.2 kg Cooling stage: R23, 2.8 kg CO₂ equivalent: 15.41 t / 41.59 t Water-cooled Pressure / Protection PS: 25 bar PT: 27.5 bar IP 54 Features - Touchscreen control - Microprocessor controller - Programmable operation - Digital setpoint/actual display - 2-zone system - Transfer cart for rapid specimen transfer - Viewing window - Integrated control cabinet - Cooling water connections Technical Construction - Separate hot and cold chambers - Stainless steel test space - Industrial-grade construction Dimensions External: 2335 x 940 x 1820 mm Handling dimensions: 1990 x 940 x 1652 mm Internal: 410 x 480 x 660 mm Weight Approx. 950 kg Documentation - Declaration of conformity - Test certificates - Operating manual - Circuit and piping diagram - Spare parts list Service before delivery (optional) - Functional check - Refrigerant service - Leak test - Test run with log Condition Used. Cosmetic condition as shown in photos. Scope of Delivery - Test chamber TSS-70/350-A - Documentation (where available) Note Used machine, sale without warranty. Inspection can be arranged upon request. Loading and transport can be organized if required. Subject to prior sale and technical modifications. For any questions, please feel free to contact us.

Condition: used, Year of construction: 2014, functionality: unexamined, STM Waterjet PremiumCut 2060 5 Heads for pure water cutting Cutting Area 6000x2000 mm (Double Table System) BFT High Pressure Pumpe Hytron 40.37 Crjdpey Ncnijfx Anwsb

Condition: used, functionality: unexamined, Year of construction: 2014, STM Waterjet PremiumCut 2060 Credpfoy Ixglex Anwjb 5 Heads for pure water cutting Cutting Area 6000x2000 mm (Double Table System) BFT High Pressure Pumpe Hytron 40.37 (60.000 hours needs to be overhauled)

Condition: used, Year of construction: 2008, OMAX 60120 P3060V 30HP (22kW) 4100 Bar EnduroMAX - machine including crank pump 30HP (22kW) 4100 Bar EnduroMax - working table 3656 mm x 1956 mm - X - Y axis travel 3200 mm x 1575 mm - air cushion (allows material to be cut while submerged) - control computer compatible with Windows 10 and OMAX Layout&Make Premium software - premium software - integrated diamond orifice head - OMAX 300kg abrasive feeder Full overhaul of the machine performed in 2024 (year of production 2008) Crjdpfx Anotmp T Doweb Possibility to equip the machine with additional accessories for an extra charge.

Condition: excellent (used), CTS Type: TSS-70/350-A Water-cooled refrigeration unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/350-A. This unit is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Typical applications: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical specifications: Type: TSS-70/350-A Temperature range: Warm chamber: +50°C to +200°C Cold chamber: -70°C to +100°C Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 20.4 kW Rated current: approx. 36.5 A Refrigeration system: Refrigerant: R404A / R23 Precooling stage: approx. 6.0 kg Cooling stage: approx. 3.0 kg Water-cooled Features / Equipment: - CTS control panel with touch display - Microprocessor-controlled regulation and monitoring system - Program operation - Digital setpoint and actual value display - 2-zone system (warm and cold chamber) - Automatic transfer basket for shock tests Technical design: - Warm and cold chamber separated - Transfer basket system for rapid temperature change - Test chamber made of stainless steel - Insert shelf / wire rack - Viewing window in door - Water cooling connections available - Integrated control cabinet Dimensions: External dimensions (HxWxD): approx. 2335 x 940 x 1820 mm Installation dimensions (HxWxD): approx. 1990 x 940 x 1652 mm Internal dimensions (HxWxD): approx. 410 x 480 x 660 mm Weight: approx. 950 kg Additional data: Cjdpfx Ansy Hkgbewsrb Protection class: IP 54 Operating overpressure: approx. 25 bar Test pressure: approx. 27.5 bar For your safety as a buyer, please note the following information! The following points are carried out on the chambers we offer before sale: 1. Functional check and replacement of necessary components 2. If needed, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run Condition: used Scope of delivery: see pictures (Specifications subject to change and errors excepted!) We are happy to answer any further questions by phone.

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled chiller unit For sale is a high-quality thermal shock test chamber manufactured by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for thermal shock testing and is commonly used in industry, research, and quality assurance. Application fields: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K over time ±2 K spatially Crodpey Hkfdofx Anweb Temperature change rate: Max. 100 K/min on average for shock test cycles (without radiant heat) Transfer rate: ≤ 15 min in the range -65°C to +200°C with 10 kg ICs Transfer time: < 10 seconds Electrical data: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 16.7 kW Nominal current: approx. 26.8 A Site-side fuse: 32 A slow-blow Connection: Cekon 32 Cooling system: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features and equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Program operation (up to 100 test programs) - Digital setpoint/actual value display - RS232 interface - 2 free switching channels for controlling test objects on-site - Fault alarm with floating contact (rated for up to 30 V-DC, 2 A) - EMC tested Technical design: - Hot and cold chambers - Transport basket with spindle drive - Test chamber / basket made of stainless steel, Material no. 1.4301 - Insert basket made of stainless steel wire - Pipe duct NW 50 with closing plug - Compressed air connection 1/4" male - Pressureless condensate drain R 1/2" internal thread - Safety door lock - Lockable door with window Dimensions as per installation drawing: External dimensions approx.: 2335 x 940 x 1820 mm Entry dimensions approx.: 1990 x 940 x 1652 mm Test chamber dimensions: Height approx. 410 mm, Width approx. 480 mm, Depth approx. 660 mm Window: 300 x 300 mm Further data: Degree of protection: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average power consumption per test cycle: approx. 8 kWh For your assurance as a buyer, the following procedures are performed on all offered chambers beforehand: 1. Function check and replacement of necessary components 2. If required, recharge with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented trial run Condition: used Scope of delivery: see pictures (Specifications subject to change and errors excepted!) If you have further questions, we are happy to assist you by phone.

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time Codpfxoy Hkd He Anwjrb - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: excellent (used), Year of construction: 2007, BIMAX TA 91 Automatic Circular Saw TECHNICAL DATA Total power requirement, rotary current: 3 x 400 V For pneumatic machines: 3 kW For hydraulic machines: 3 kW Customer-provided mains fuse: 16 A Supply line: 4 x 2.5 mm, 3P + E Air connection: Diameter: 12 mm Supply line: 8 – 10 bar, 40 l/min Operating pressure: 6 bar Spindle drive via three-phase motor: B5-100S 4/2-pole, Dahlander circuit: 1420 / 2840 rpm Power: 1.8 / 2.5 kW Saw blade mount: 32 mm Drive pin: 8 mm Pitch circle of drive pin: 45 mm Cutting wheel mount: 22 mm Saw blades: 160 x 1 to 300 x 2 mm Passage range: Round up to 65 mm Square up to 55 x 55 mm Rectangular up to 80 x 50 mm Standard clamping jaw for diameters: 10 – 60 mm Material feed length: 0 – 250 mm Saw weight: 500 kg Csdpev I Dmlofx Anworb Hydraulics: 120 kg No liability is assumed for the accuracy, completeness, or timeliness of this information.

Condition: good (used), Year of construction: 2002, Behringer Eisele VA-0-250-NC Circular saw TECHNICAL DATA Sawing range: 90 ° Cedovdk A Eepfx Anwerb Saw blade diameter: 25 cm Bore: 40 mm Cutting range: 10-75 mm Cutting length: 5-900 mm Speed: 2800 rpm Cutting speeds: 26/52/103/206 SFPM or 0.13/0.26/0.52/1.05 m/s Feed speeds: 0-40 mm/sec NC axis: Yes Dimensions: 190 x 127 x 190 Weight: 1300 kg We assume no liability for the accuracy, completeness and up-to-dateness of the information provided

Condition: new, Year of construction: 2019, operating hours: 0 h, machine/vehicle number: 20928, Burkhalter water treatment plant (state of the art, Swiss top quality) Crodpep Hf Idjfx Anwsb - Brand new (the unit has never been installed) - Please consult the attached PDF catalog: There you will find a detailed description of the plant as well as an extensive photo gallery (starting on page 8).

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 107500 € 2031.75 € 360 mm Ø360 x 40 mm 40 - 280 U/Min rund: 20 - 100 mm; quadra 60 mm 10 - 9999 mm Cjdpfsy Nnxgjx Anwsrb 900 mm 15 kW 3400 mm 2675 mm 2750 mm 3450 kg 21,65 kW Mass production in continuous operation is done by BMDO 100 XS when producing cut-off pieces of steel and non-ferrous metals with a material cross-section up to a diameter of 100 mm. BMDO 100 XS is designed to be used with TCT circular saw blade in order to cut solid bars in high speedand excellent precise. It is also suitable for HSS blades to cut tubes. With the Standard 800mm stroke servo feeding and 6 meters automatic loader. BMDO 100 XS is perfect for large-scale production of solid bars. STANDARD ACCESSORIES: automtic loader 6 m motorized roller table 3 mMikrospray Coolant Hydraulic Vice Inverter Control Panel Saw Blade Brush Cover Switch Heavy Duty Gearbox OPTIONAL EQUIPMENT (prices on request): mist filter 6 m roller table

Condition: excellent (used), Year of construction: 1966, I sell a circular saw made in Germany. Company Eisele model vms II in good condition Codpfxevbwfne Anwsrb

Condition: good (used), Pumpex water pump 300m3/h, 7.5kw Cjdpfxsvgnvbj Anwsrb

Condition: excellent (used), For sale: complete fire-fighting trailer equipped with a professional ALCO MONITOR water cannon. The set is fully mobile – ideal for fire brigade use, fire protection, and securing large areas (fuel depots, sawmills, production plants, storage yards). Technical condition: • ALCO / MONITOR water cannon – heavy-duty cast iron construction • Full adjustment of direction and spray angle (control wheels) • Directional nozzle on extended boom • KALI Anhänger Service GmbH trailer, GVW 700 kg • Hitch: Peka Fahrzeugbau, type DV127 • Two side tanks with filling ports • Shut-off valves, fire-fighting quick couplings • Stabilizing supports with height adjustment • Lighting installation, fenders, wheels in very good condition • Well-maintained, complete, ready to use Crsdpfsx Edrrsx Anwob Applications: • Voluntary/Professional fire brigades • Large production facilities • Timber yards, sawmills • Chemical and fuel plants • Securing mass events • Extinguishing fires from a great distance / high water flow

Condition: excellent (used), Year of construction: 2003, Max. saw blade diameter: up to 300 mm Machine head tiltable: 45°-90°-45°-30° Cutting diameter at 90°: 100 mm Square tube: 85 x 85 mm Flat profiles, hollow: 130 x 85 mm Speed range: 40 / 80 rpm Cedpfx Aney E Ulljwerb Drive power: 1.0 / 1.2 kW Machine dimensions (L x W x H): 650 x 600 x 1650 mm Weight: 185 kg Accessories / Special Features: • Vertical guidance of the saw head • Continuously adjustable mitre facility 45°-90°-45°-30° • Infeed/outfeed roller conveyors, each approx. 1 m in length • Manual feed • Coolant system • 1 saw blade included • CE compliant This very good VMS 300 is from a training workshop. Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: used, This listing is for the Grant JB Academy 6005 Water Bath The unit is in full working condition and is ready for immediate use Grant Instruments JB Academy range of digital unstirred water baths — basic laboratory water baths designed for heating and maintaining liquids at controlled temperatures. They’re often used in teaching labs, research settings, schools and colleges where a simple, reliable water heating bath is needed. Credpsy Iw Eyefx Anwsb

Condition: used, This listing is for the Clifton NE4-8P Water Bath The unit is in full working condition and is ready for immediate release Crjdpjy Iw Alofx Anwob The Clifton NE4-8P Digital Water Bath With Circulator is an 8-litre laboratory water bath with an integrated pump that recirculates temperature-controlled water for uniform heat distribution. It’s designed for accurate temperature control with a PID digital controller, LED display, and temperature alarm Common lab uses include incubating samples, warming reagents, and stabilising solutions at set temperatures