Used Cross Table for sale (19,895)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Hsdpfx Afjzp H R Ej Aonr Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: used, Roller support for saw, composed of: 2 supports: L 3000 mm x Max width 550 mm x Mini height 800 mm - Max height 950 mm Hnodpfx Afezmxvuo Aor 1 support fitted on machine side (see photo): L 3000 mm x Max width 550 mm x Mini height 800 mm - Max height 950 mm Rolls width: 450 mm

Condition: used, Log table with elevator and log scanner Rema Control - logs up to 6 m - between rails 1100/1050/ 1050/1250 mm - log table length: 10 m Hnedpfx Aju Smq Sof Asr - Rema Scanner - log infeed conveyor

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, degree of automation: automatic, laser type: fiber laser, laser power: 3,000 W, warranty duration: 24 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Working Area (mm): 3048×1524 X-Axis Travel (mm）: 1524 Y-Axis Travel(mm）: 3048 Z-Axis Travel（mm）: 80 Hnjdpfjxvwcxex Af Aor X/Y Axis Positioning Accuracy: ≤0.03mm/m X/Y Axis Repositioning Accuracy: ≤±0.02mm Maximum Synthetic Positioning Speed: 150m/min Maximum Acceleration: 1.2G Cutting Slit Width: 0.1mm-0.5mm (measured for platesless than3mm thick) Cutting Surface Roughness: Ra3.2um-Ra25.4um(measured for plate thickness below3mm） Floor Size(mm): 6000*3000 Mainframe Dimension(mm): 5000*2300*1800 Screen Size: 21"LCD TransmissionMode: Rack andpinion dual drive Table Loading Capacity: 1.1(ton)

Condition: like new (used), Range (depending on lighting conditions): up to 15 m Range with laser receiver: 30 m and more Leveling accuracy at 5 m: +/- 1 mm Self-leveling range: 4° +- 0.5° Accuracy of the horizontal line at 5 m: +- 1.5 mm Accuracy of the vertical line at 3 m: +- 0.75 mm Number of laser lines: 2 Hnsdpod Ecncefx Af Ajr Weight: 485 g

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition Hnodpfsfv Hphex Af Aor - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: used, Outfeed table before resaw IDL000793 Hedpfxoul Rgvj Af Aenr

Condition: excellent (used), Year of construction: 2020, - total length: 8,1 m - total width: 1200 mm - height: 950 mm Hydraulic lift, lifting capacity around 1 ton. Hnsdpfx Astddw Aef Aer

Condition: new, functionality: fully functional, power: 1.1 kW (1.50 HP), Year of construction: 2026, G450 Gemini table for gold beneficiation and seperation Hnodjytnn Iepfx Af Ajr

Condition: ready for operation (used), Year of construction: 2001, machine/vehicle number: 8745, functionality: fully functional, table width: 500 mm, table length: 2,500 mm, spindle speed (max.): 10,000 rpm, TECHNICAL DETAILS Table length: 2,500 mm Table width: 500 mm Max. tool diameter for milling head: 160 mm Max. tool diameter for collet chuck: 160 mm Spindle tilt: automatic Spindle height adjustment: automatic Spindle speed adjustment: manual, in steps Spindle speed: 3,000–10,000 rpm Hnodpfxszrmp Hj Af Aer Number of speeds: 2 Motor brake: present MACHINE DETAILS Main motor power: 7.5 kW Dimensions & Weight Dimensions (L x W x H): 1,800 x 1,200 x 1,900 mm Machine weight: 1,200 kg Number of transport packages: 1 EQUIPMENT Feeder Mec4v (number of feed wheels: 3) Guide (brand Aigner)

Condition: used, machine/vehicle number: 008703, X axis working area: 3650 mm Y axis working area: 1600 mm Hnjdpfx Aozq Ur Tef Ajr Working Table: Flat table Main Electrospindle power: 15 KW Number of controlled axes: 3 axes Total number of drilling spindles: 37 Total number of tool changer positions: 18

Condition: used, machine/vehicle number: 008238, X axis working area: 3660 mm Y axis working area: 1550 mm Working Table: Flat table Main Electrospindle power: 12 KW Number of controlled axes: 3 axes Total number of drilling spindles: 12 Hsdpfx Afsx A E Tfe Ajnr Total number of tool changer positions: 15

Condition: used, machine/vehicle number: 005796, X axis working area: 3700 mm Y axis working area: 1550 mm Main Electrospindle power: 9 KW Number of controlled axes: 3 axes Hsdpehwi U Tofx Af Aonr Total number of drilling spindles: 10 Total number of tool changer positions: 8

Condition: used, machine/vehicle number: 007564, X axis working area: 3700 mm Y axis working area: 1550 mm Working Table: Flat table Main Electrospindle power: 10 KW Hsdpfoum H Eksx Af Asnr Number of controlled axes: 3 axes Total number of drilling spindles: 12 Total number of tool changer positions: 13

Condition: used, machine/vehicle number: 008647, X axis working area: 3650 mm Y axis working area: 1500 mm Working Table: Flat table Main Electrospindle power: 8.5 KW Number of controlled axes: 3 axes Total number of drilling spindles: 26 Total number of tool changer positions: 12 Hsdpfx Ajzdquwjf Asnr

Condition: good (used), overall weight: 10,364 kg, Year of construction: 2019, 2019 GENERAL BROACH 10-30 GBTU VERTICAL TABLE UP BROACH Equipped with: Retriever Shuttle Table Chip Conveyor Auto Load Grayco Lube AB Panelview Coolant Tank & Pump Specifications: Capacity: 10 Ton Stroke: 30" Hjdpfxjrtrzao Af Aenr Table Up 1″ Puller / Retriever Hydraulic Power Unit Chip Conveyor Machine Dimensions (approx.): 165″ x 48″ x 60″ Machine Weight Total (approx.): 22,800 lbs. Machine Column (approx.) : 13,000 lbs. Base w/ Chip Conveyor (approx.): 4,700 lbs. Electrical Panel (approx.): 600 lbs. Hydraulic Power Unit (approx.): 4,500 lbs.

Condition: new, Table size: 420 x 450 mm Hnsdpfxsc Snvfs Af Ajr Table height: 215 mm Table swivel range: up to 45° Saw blade/cutting blade diameter: 200 mm Cutting depth: 47 mm Electrical connection: 230 V AC Weight: 14.5 kg

Condition: excellent (used), functionality: fully functional, load capacity: 5,000 kg, rotary table diameter: 1,500 mm, table load: 5,000 kg, Bode Welding Positioner Rated Load Capacity:5000Kgs Table Diameter:1525mm Motorised Tilt: 135 Degrees Hsdpfx Afezrnnwe Asnr Table Rotation Speed: 0.05 - 1.00 RPM Motor:2.2KW Dimensions: 1600 x 2100 x 1200mm Weight: 3500Kgs

Condition: used, Price: On request - Documentation available: No - CE certificate present: No Financial information Hnsdpfx Aozul T Ajf Ajr VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2007, total width: 1,070 mm, total length: 9,000 mm, total height: 1,420 mm, Colour: Blue Weight: 1.500 kg - Year: 2007 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 48-2007-1403 - Main motor power [kW]: 5.5 - Max. cutting depth [mm]: 320 - Max. cutting height [mm]: 100 Hnedpfxszufv Rj Af Asr - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 30 - Table length [mm]: 5000 - Table width [mm]: 350 - Spindle speed control: Not applicable - Voltage [V]: 400 - Current consumption [A]: 10.3 - Fuse [A]: 16 - Power [kW]: 5.5 - Transport dimensions: 9000mm x 1070mm x 1420mm (l x w x h) - Transport weight [kg]: 1500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: new, table length 1220 mm table width 760 mm table height 910 mm weight 226 kg Hnsdpjxqrhlsfx Af Aer

Condition: new, Year of construction: 2025, table length 3000 mm table width 1500 mm table height 200 mm weight 1500 kg Manufacturer: GERD WOLFF Technical Details: • Length 3000 mm • Width 1500 mm • Height 200 mm • Weight 1500 kg • Hole diameter 28 mm • Hole spacing 100 mm • Plate thickness: 25mm Advantages and Features: • 3-day gas nitriding process • Increased corrosion resistance • Weld spatter adhesion protection • Maximum load capacity • Enhanced fatigue strength • Improved vibration resistance • Fine scale engraving • Reinforcement with welded seams and ribs on the underside • Optimal working height of 820-865 mm • 8 height-adjustable support legs • Available with a matching accessory set (optional) Our welding tables are manufactured using HT 300 cast iron and are nitrided as a whole after mechanical processing. Furthermore, they feature precise fine scale engraving using laser technology. To ensure adequate stability, our welding tables are reinforced with welded seams and ribs on the underside (see illustrations). Additionally, they undergo a 3-day gas nitriding process, enhancing their corrosion resistance, fatigue strength, and vibration resistance, among other factors. All our tables come with adjustable legs. The minimum height adjustment range is 620 mm, while the maximum is 665 mm, allowing for a variable working height of 820 to 865 mm. Additional available dimensions: • 1000 x 1000 x 200 • 2000 x 1000 x 200 • 1200 x 1200 x 200 • 1500 x 1000 x 200 • 1500 x 1500 x 200 Hnedpfxsymf Rtj Af Asr • 1500 x 2000 x 200 • 2000 x 3000 x 200 • 3000 x 1500 x 200 • 3000 x 2000 x 200 • 4000 x 2000 x 200 Please note that the images are not to scale and are for illustrative purposes only. Our welding tables are produced for our distribution brand "GERD WOLFF Maschinenfabrik" by a reputable manufacturer. 3D Welding Table - 3D Clamping Fixtures - 3D Precision Welding Table

Condition: new, Year of construction: 2026, table length 1000 mm table width 1000 mm table height 200 mm weight 300 kg Manufacturer: GERD WOLFF Website: Technical Details: • Length 1000 mm • Width 1000 mm • Height 200 mm • Weight 300 kg • Hole diameter 28 mm • Hole spacing 100 mm • Plate thickness: 25mm Advantages and Features: • 3-day gas nitriding process • Increased corrosion resistance • Weld spatter adhesion protection • Maximum load capacity • Enhanced fatigue strength • Improved vibration resistance • Fine scale engraving • Reinforcement with welded seams and ribs on the underside • Optimal working height of 820-865 mm • 4 height-adjustable support legs • Available with a matching accessory set (optional) Our welding tables are manufactured using HT 300 cast iron and are nitrided as a whole after mechanical processing. Furthermore, they feature precise fine scale engraving using laser technology. To ensure adequate stability, our welding tables are reinforced with welded seams and ribs on the underside (see illustrations). Additionally, they undergo a 3-day gas nitriding process, enhancing their corrosion resistance, fatigue strength, and vibration resistance, among other factors. Hnsdpfxey S D Naj Af Ajr All our tables come with adjustable legs. The minimum height adjustment range is 620 mm, while the maximum is 665 mm, allowing for a variable working height of 820 to 865 mm. Additional available dimensions: • 1000 x 1000 x 200 • 2000 x 1000 x 200 • 1200 x 1200 x 200 • 1500 x 1000 x 200 • 1500 x 1500 x 200 • 1500 x 2000 x 200 • 2000 x 3000 x 200 • 3000 x 1500 x 200 • 3000 x 2000 x 200 • 4000 x 2000 x 200 • 2400 x 1200 x 200 Please note that the images are not to scale and are for illustrative purposes only. Our welding tables are produced for our distribution brand "GERD WOLFF Maschinenfabrik" by a reputable manufacturer. 3D Welding Table - 3D Clamping Fixtures - 3D Precision Welding Table

Condition: used, Year of construction: 1999, plate width 2980 mm Hnsdpfx Afegxqvze Asr plate depth 3000 mm plate height 1400 mm total power requirement 11 kW

Condition: used, centre height / mm weight 160 kg Hedpfx Afsy S Dyls Ajnr diameter 500 mm