Used Die-Cast for sale (5,717)

Condition: ready for operation (used), Year of construction: 1996, Clamping force: 3150kN, opening force: 10,000daN, closing stroke: 500mm, ejector force/retraction force: 159/82kN, ejector stroke: 120mm, mould height: 300-700mm, platen dimensions: 900x900mm, tie bar spacing: 550x550mm, tie bar diameter: 110mm, injection position: mm, max. injection force: 350kN, injection stroke: 430mm, injection plunger diameter: 50/60/70/80mm, shot volume: 563/811/1103/1441cm³, specific injection pressure: 1783/1238/909/696daN/cm², corresponding projected area: 177/254/347/453cm², max. projected area: 1050cm² at 300daN/cm², operating pressure: 140bar, dry cycle time (DIN 24480): 500, drive motor: 22kW, control: Datacontrol, length: 6900mm, width: 2000mm, height: 2800mm, weight: 14t, operating hours: 77,185h, shot count: at least 1,147,108, however not guaranteed due to a hardware replacement, adjustable opening stroke, with Striko Westofen W455 holding furnace, ABB IRB 2400 (M96/F10) industrial robot, and documentation. An on-site inspection is possible. Dkedpfxoza E Rms Acksn

Condition: repair required (used), Year of construction: 2001, functionality: not functional, FRECH DAK 720-71 RC Die-Casting Machine, used Machine number 440403, clamping force 8,000 kN, clamping stroke 825 mm, ejection force 364 kN, ejection stroke 180 mm, mould height 350 to 1,000 mm, clamping platens 1,300 x 1,300 mm, tie bar spacing 825 mm, tie bar diameter 180 mm, maximum casting force 713 kN, casting stroke 600 mm, casting piston diameter 70 to 120 mm, casting volume 1,539 to 4,523 cm³, operating pressure 160 bar, drive motor 45 kW, equipped with MELTEC AVDF 1200/5000 dosing furnace, year 2017, serial number System sold as a donor for spare parts Technical details: Dimensions (L x W x H): approx. 8,000 x 7,500 x 3,500 mm Weight: approx. 36,000 kg Year of manufacture: 2001 Dsdpfx Ajwc Tdzockokn

Condition: new, Year of construction: 2020, Electric furnace MELTEC Typ ZC50/180 TOC incl. iron steel crucible, isolated coverand substructure. Without control cabinet (can be ordered aditionally) Dedpfx Ajy E Tynockokn Electric heating with heating elements. Transfer of melt below bath level from melting to casting chamber by pump to provide constant bath level together with shot to shot consistency. Crucible content: 820,0 kg/Zn Melting capacity: 180,0 kg/Zn/h Electrical connection: 27,0 kW Type: ZC 50/180 TOC suitable for DAW 50F and W50Zn

Condition: new, Year of construction: 2023, Electric furnace MELTEC Typ ZC80/180F ECO V2 incl. iron steel crucible, isolated coverand substructure. Without control cabinet (can be ordered aditionally) The EcoMelTec furnace combines the advantages of the proven multi chamber furnace with many new functions for double savings. New functions help to optimize the handling of the casting process just as: Dkodoy E Tyhopfx Acken - Good accessibility for cleaning purposes via flexibly mountable flap cover - New pump design enables longer cleaning intervals - Storage for slag container - facilitates cleaning the melt bath - Symmetrical furnace design - no right-hand/left-hand version required Crucible content: 820,0 kg/Zn Melting capacity: 180,0 kg/Zn/h Electrical connection: 27,0 kW Type: ZC 80/180 F ECO V2 suitable for DAW 80F and W80Zn

Condition: new, Year of construction: 2022, Electric furnace MELTEC Typ ZC20/120F ECO V2 incl. iron steel crucible, isolated coverand substructure. Without control cabinet (can be ordered aditionally) The EcoMelTec furnace combines the advantages of the proven multi chamber furnace with many new functions for double savings. New functions help to optimize the handling of the casting process just as: - Good accessibility for cleaning purposes via flexibly mountable flap cover - New pump design enables longer cleaning intervals - Storage for slag container - facilitates cleaning the melt bath - Symmetrical furnace design - no right-hand/left-hand version required Dsdey E Tybjpfx Ackekn Crucible content: 420,0 kg/Zn Melting capacity: 120,0 kg/Zn/h Electrical connection: 21,5 kW Type: ZC 20/120 F ECO V2 suitable for DAW 20F and W20Zn

Condition: used, Year of construction: 2017, workpiece weight max. 2000 g used weightcontrol WC2000 for die casting machines up to a unit weight of 2000 grams. The device has been checked and repaired by the manufacturer Dkjdpfx Acey Diauekjn

Condition: used, Year of construction: 1994, functionality: limited functionality, Used Oskar Frech DAW 125 with control cabinet and crucible Dsdpfx Acewywn Eskjkn

Condition: refurbished (used), Year of construction: 2013, functionality: fully functional, type of input current: three-phase, input voltage: 380 V, TS1600 creasing and die cutter machine is an indispensable piece of post press equipment which is widely used for die cutting, and creasing of adhesive stickers, carrier bags, book covers, packing boxes, greeting cards, desk calendars, corrugated cartons, etc. It can effectively cut the desired material into large numbers of the same shape. Max. die cutting size 1600 mm X 1200 mm Dsdpfx Acey Sz S Sekskn Working speed 20±2 pieces/min Machine is at our premises, testing on-site is possible.

Condition: new, Brand New - One Year Warranty Max. die cutting size 1100 X 800 mm Working speed 23±2 s/min Max. rule length ≤30 m Motor power 5.5 kW Weight 4500 kg Overall machine dimensions Dkjdpovv R Hzjfx Acksn 2080 X 1950 X 1900 mm

Condition: new, Year of construction: 2025, ML750 Dksdpfovv R H Usx Ackjn Inner chase size 750 X 520 mm Max. die cutting size 750 X 520 mm Working speed 28±2 s/min Max. rule length ≤15 m Motor power 2.2 kW Weight 2000 kg Overall machine dimensions 1650 X 1540 X 1650 mm

Condition: like new (used), Year of construction: 2022, Hot stamping plate dimension(W*L): 330mm* 260mm Die cutting plate dimension(W*L): 330mm* 350mm Dksdpfx Acjp H Swdoken Max.unwind roll diameter& Max.rewind roll diameter: 650mm(can load 2000 meters material) Max.speed: 23000 times/h Applicable blade height: 7mm-23mm Applicable hot stamping tooling height: 1.5-4mm Die cutting accuracy: 0.1mm Hot stamping accuracy: 0.2mm Dimensions: 5300mmx1300mmx1700mm Voltage/current: 3 phase 380V/32A Main motor power :7.5KW Gross power: 15KW Total weight: About 4000KG

Year of construction: 2025, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: 20251122351, Complete solution for transporting bulk materials such as wood chips, wood pellets, shredding material, granulate, etc. Aluminium angled conveyor belt incl. mobile frame Horizontal section: 1,200 mm Inclined section: 1,800 mm Angle at bend: 40 degrees each Infeed height from floor: 500 mm Discharge height: 1,600 mm Conveyor belt width: 700 mm Extremely robust aluminium construction, heavy-duty version! PU conveyor belt incl. cleats and corrugated sidewalls Drive: Motor 0.55 kW (customizable), speed approx. 0.77 m/sec Connection: 220/240V, 50Hz, IP54 protection class Drive etc. ready for connection, motor control optional Corrugated sidewalls: 80x50 mm T-60 cleats, short pitch 2-ply, especially cross-stabilized Sidewalls and cleats, as well as belt, are endlessly high-frequency welded In the angled section, the belt is guided on both sides by 4 hold-down rollers each. The belt is produced with a 100 mm edge-free zone on both sides. Due to the corrugated sidewalls on both sides, the usable belt width is reduced: Dkedpfjyt Ia Dex Ackjn Usable width: 400 mm, calculated as follows: (top view) lateral arrangement 100+50+400+50+100 mm Demo unit - Available immediately! - Can be viewed under power All prices are net prices plus 19% VAT All information without guarantee, only while stocks last!

Condition: like new (used), Device for cleaning die-cut sheets German production, Metabo. 230V power supply. Easy-to-use, manual device for removing external waste from the pallets of die-cut sheets. Safe, two-handed operation of the device. Dkedpswyxi Rsfx Acksn

Condition: new, Year of construction: 2026, Aluminum Incline Conveyor with Substructure (PU/PVC with Cleats & Corrugated Sidewalls) We offer a robust incline conveyor in aluminum construction design for the reliable transport of piece and bulk materials—ideal for industry, trade, recycling, woodworking, and much more. Thanks to cleats and corrugated sidewalls, secure material transport is ensured even on steep conveyor routes. _____ Technical Data (Sample Configuration): ✔ Infeed height: customisable ✔ Inclined section: length freely selectable ✔ Discharge height: customisable ✔ Substructure with adjustable leveling feet & machinery feet or with transport castors → for compensating uneven surfaces / stable positioning _____ Design / Frame: ✔ Aluminum construction profile ✔ Double profile 90x45 mm or reinforced triple profile 135×45 mm ✔ Continuous wear plate 2.0 mm galvanized or 1.4301 stainless steel (VA) _____ Rollers / Drive: ✔ Drive and deflection rollers made from S235 steel, welded & machined ✔ Diameters: Ø100, 150 or 220 mm ✔ Shafts fixed with pillow block bearings ✔ Drive: shaft-mounted geared motor 0.18 – 3.0 kW ✔ Belt speed: individually adjustable ✔ Connection: 230/400V, 50Hz, IP54 protection class (standard) ✔ Drive prewired up to the motor terminal box ➡️ Commissioning must be carried out by a qualified electrician _____ Conveyor Belt / Cleats: ✔ PVC conveyor belt DM 10/2 0+005 PVC green ✔ Belt widths: 100, 200, 300, 400, 500, 600, 700, 800, 900, or 1,000 mm ✔ Endless high-frequency welded (stepped joint) ✔ 2-ply, 3-ply with extra lateral stability ✔ Corrugated sidewalls: up to 80 mm high ✔ Cleats: customizable ✔ Pitch customizable _____ Options / Accessories Available: ✔ Infeed plates ✔ Hoppers / infeed hoppers ✔ Bunkers / loading bunkers Dsdsyhzpljpfx Ackekn ✔ Discharge hoppers ✔ Special lengths / special widths ✔ Cleats & corrugated sidewalls as required _____ ✔ Custom solutions made to your specifications ✔ Industrial quality ‘Made in Germany’ Dimensions, versions, and pricing on request Simply reach out—we provide fast and straightforward advice. Discover tailored solutions for your industry! As an innovative mechanical engineering company, we are proud to offer bespoke solutions for the recycling, food, and processing industries. Our comprehensive product portfolio covers everything from conveyor systems and flat belt conveyors to incline conveyors, angle conveyors, and Z-conveyors. In addition, we manufacture loading bunkers, magnetic separators, overband magnetic separators, drum magnetic separators, and dosing bunkers—all tailored to meet our customers’ specific requirements. We understand that every industry and every project is unique, which is why we tailor our solutions precisely to your needs and specifications. Complex projects are an exciting challenge for us, and we look forward to developing innovative solutions together with you. With us, there are no off-the-shelf solutions—every problem gets the right answer! Challenge us! Contact us and discover how we can turn your requirements into custom solutions. Together, we will shape the future of your production processes!

Year of construction: 2026, condition: new, Robust Steel Construction – Designed for Continuous Operation The basic structure consists of a stable construction steel frame, manufactured from laser-cut, bent, and welded components. The surface features a high-quality RAL0208 powder coating. Modular Design: Our conveyor belt frames are available as transportable sections. This makes the system: • Easy to transport and assemble • Extendable or shortenable at any time • Ideal for future modifications or system adaptations Conveyor Technology & Carrying Rollers The carrying roller construction in the lower run is designed for smooth and reliable operation: • Shaft diameter: 60/15 mm • Roller station spacing: approx. 500 mm (customizable) • Closer roller spacing in the infeed area available on request for higher load capacity Drive & Rollers The drive drum and return drum are made of S235 steel, welded and precisely machined: • Ø 220 × 700 mm, crowned and finish-turned • Shaft secured with tension bearings • Bearing positions with robust UCF flange bearings, including lubrication nipples Drive Unit: • Hydromec worm gear motor, 1.1 kW • Belt speed: approx. 1.15 m/s • Connection: 400V / 50 Hz, protection class IP54 • Drive supplied ready for wiring to motor terminal box (commissioning must be carried out by a qualified electrician) • Motor mounted on the right, pull configuration in the conveying direction Conveyor Belt A durable, industrial-grade belt is used: • DM EP250/2, 3+1.5 cover • Chevron profile 17 mm high, 650 mm wide • Profile-free splice area • Endless hot vulcanized Custom Options & Accessories (depending on requirements) Djdpoyhznnjfx Ackokn The modular design allows all components to be precisely adapted to your process, such as: ✅ Special lengths & widths ✅ Side plates / wave edges (for lateral guidance and increased conveying stability) ✅ Infeed plates / feed plates (wear-optimized, material-friendly) ✅ Feed/infeed hoppers (for clean loading of bulk material) ✅ Discharge plates / discharge chutes ✅ Cleat profiles / alternative belt specifications ✅ Adjustment of roller spacing & carrying roller geometry ✅ Special coatings / custom designs

Year of construction: 2026, condition: new, DM Flat Conveyor Belt Type FB-700 without substructure for bulk material conveying Conveyor belt length: 6,000 mm Belt width: 650 mm Fabricated from structural steel, laser-cut, bent, and welded Base frame powder-coated in RAL 5015 Modular conveyor belt frame construction / sections available in transportable lengths. Frame structure extendable or can be shortened at any time. Carrier roller system on the return strand, shaft Ø60/15 mm Roller station spacing approx. 500 mm (custom options possible) Closer roller spacing in load area Drive drum + tail drum made of S235 steel, welded and machined Ø220x700 mm crowned, shaft fixed with pillow block bearings. Drive: Hydromec worm gear motor 1.1 kW, belt speed 1.15 m/sec Connection 400 V, 50 Hz, protection class IP54 Drive supplied prewired to motor terminal box (Commissioning must be performed by a qualified electrician) Motor mounted on right side in direction of transport, pull configuration. Bearing points equipped with robust UCF flange bearings incl. grease nipples. Rubber conveyor belt DM EP250/2 3+1.5 cover Chevron profile, 17 mm high x 650 mm wide Dedpfx Asyhznhockskn Joint section without profile, endlessly hot vulcanized

Condition: new, Year of construction: 2026, Aluminum Angled Conveyor Belt with Substructure including adjustable feet and machine feet for leveling uneven surfaces Horizontal section: 2,500 mm Inclined section: 6,000 mm Dkedpoyhzhzsfx Acksn Incline angle at the bend: 45° Height of the horizontal section: 350 mm Total conveyor length measured on the floor: 6,750 mm Discharge height at the end of the conveyor: 4,500 mm Design: Aluminum construction - Double profile reinforced 90x45 mm - Full-surface discharge sheet 2.0 mm galvanized Drive drum and return drum S235 steel, welded and machined Ø100x620 mm crowned and turned, shaft fixed with pillow block bearings. Drive: Shaft-mounted gear motor 1.10 kW, belt speed: 0.53 m/sec Electrical connection 230/400 V, 50 Hz, IP54 protection class Drive supplied ready for connection up to the motor terminal box (Commissioning must be carried out by a qualified electrician) PU conveyor belt DM 10/2 0+005 PU including wave edge PU petrol matte Belt width: 600 mm 2 pcs wave edges 50 mm high, 25 mm wide, high-frequency welded 42 pcs T-40 cleats, 400 mm long, approx. 401 mm spacing Belt material: 2-ply, highly cross-stable In the bend area, the belt is guided on both sides by 3 hold-down rollers each. The belt features a 70 mm edge-free zone on both sides. Due to the wave edges, the usable belt width is reduced: Usable width: 300 mm, as follows: (top view) cross section 70+25+5+400+5+25+70 mm Special features: Belt guidance via PVC wedge strip on the running surface profile - 10x6 mm - Including widened substructure for improved stability against top-heaviness - Including cut-out in the discharge sheet - Including sliding guides in drive and return drums - Including magnet-free zone in the area of the overbelt magnet separator - Including bracket for DMPM1200 in the inclined section Discover customized solutions for your industry! As an innovative mechanical engineering company, we are proud to offer tailor-made solutions for the recycling, food, and further processing industries. Our comprehensive product portfolio includes everything from conveyor belt systems, flat conveyors, inclined conveyors, and angled conveyors to Z-conveyors. In addition, we manufacture feed hoppers, magnetic separators, overband magnet separators, drum magnets, and dosing bunkers – all custom-built to our customers' specific requirements. We understand that each industry and project is unique. That is why we individually adapt our solutions to your specifications and requirements. Complex projects are an exciting challenge for us, and we look forward to developing innovative solutions together with you. For us, there are no special designs – we find the right solution for every challenge! Put us to the test! Contact us and discover how we can transform your requirements into bespoke solutions. Let’s shape the future of your production processes together! Conveyor belt, conveyor system, discharge belts, belt conveyors, magnetic separator, overband magnet separator, recycling, wood chips, plastics, metal-free, metal detection, neodymium, overband magnet, magnetic belt separator, lifting magnets, filter rods, magnetic grids, magnetic grates, metal separator, block magnet, filter systems, dosing hoppers, feed hoppers, filling systems

Condition: new, Year of construction: 2026, Aluminum angled conveyor with substructure Including adjustable feet as well as machine feet for leveling uneven surfaces Horizontal section: 3,500 mm Inclined section: 2,100 mm Inclination angle at bend: 45° Total conveyor length measured on the floor: 5,000 mm Discharge height: 2,000 mm Height of horizontal section: 500 mm Design: Aluminum structural construction - Triple-reinforced profile 135x45 mm - Full-surface discharge sheet 2.0 mm, galvanized Drive drum + tail drum made from S235 steel, welded and machined Dkodoyhzhuspfx Acken Ø150x820 mm, crowned, shaft mounted in plummer blocks. Drive: Shaft-mounted gear motor 1.1 kW, belt speed 0.77 m/sec Connection 230/400V, 50Hz, protection class IP54 Drive prewired to motor terminal box (Commissioning must be performed by qualified electricians) PVC conveyor belt DM 15/4 0+007 PVC including PVC wave edge, green Belt width: 800 mm 2 pcs. wave edges, 80 mm high, 50 mm wide, high-frequency welded 32 pcs. T-50 cleats, approx. 355 mm spacing Belt material: 2-ply, especially cross-stable At the bend, the belt is guided on both sides by 3 hold-down rollers each. The belt features a 70 mm edge-free zone on each side. Due to the wave edge on both sides, the usable belt width is reduced: Usable width: 490 mm, calculated as follows: (top view) transverse arrangement 100+50+5+490+5+50+100 mm Discover custom solutions for your industry! As an innovative mechanical engineering company, we are proud to offer tailored solutions for the recycling, food, and processing industries. Our extensive product portfolio ranges from conveyor systems and flat conveyors to incline conveyors, angled conveyors, and Z-conveyors. In addition, we manufacture feed hoppers, magnetic separators, overband magnetic separators, drum magnetic separators, and dosing bunkers – all according to our customers’ specific requirements. We understand that every industry and project is unique. That’s why we customize our solutions to your individual needs and specifications. Complex projects are an exciting challenge for us, and we look forward to working with you to develop innovative solutions. With us, there is no such thing as a special solution – we find the right solution for every problem! Challenge us! Contact us and discover how we can transform your requirements into customized solutions. Together, we will shape the future of your production processes! Conveyor, conveyor system, discharge belts, belt conveyor, magnetic separator, overband magnetic separator, recycling, wood chips, plastics, metal-free metal detection, neodymium, overband magnet, magnetic belt separator, lifting magnets, filter rods, magnetic grids, magnetic grate, metal separator, block magnet, filter systems, dosing bunker, feed bunker, filling systems

Condition: new, Year of construction: 2026, functionality: fully functional, Aluminum Z-conveyor belt with base frame, including adjustable feet and freely swiveling transport castors with parking brakes. Horizontal section: 800 mm Inclined section: 3,000 mm Second inclined section: 1,200 mm Angle of incline at each bend: 60° Total conveyor belt length measured on the floor: 3,500 mm Height of the horizontal section: 400 mm Design: Dksdpfx Asyhzhnsckon - Aluminum construction with 2x reinforced profile, 90x45 mm - Full-surface discharge sheet, 2.0 mm, galvanized - Drive roller and deflection roller made from welded and machined S235 steel - Ø100x720 mm crowned turning, shaft fixed with pillow block bearings Drive: Parallel shaft geared motor 1.10 kW, belt speed: 0.53 m/sec Connection: 230/400V, 50 Hz, protection class IP54 Drive wired ready for connection up to the motor junction box (commissioning must be performed by a qualified electrician) PU conveyor belt DM 10/2 0+005 PU, including wave edge PU, petrol matt finish, AS, especially cross-rigid with hard cover Conveyor belt width: 700 mm 2 pcs. wave edges, 50 mm high, 25 mm wide, high-frequency welded 34 pcs. T40 cleats, centered, 430 mm long, spacing approx. 299 mm Belt material: 2-ply, especially cross-stable At each bend, the belt is guided on both sides with 3 hold-down rollers each. The belt is manufactured with a 70 mm edge-free zone on each side. Due to the wave edge on both sides, the usable belt width is reduced: Usable width: 500 mm, determined as follows: (top view) Cross-section 70+25+5+500+5+25+70 mm Belt guidance via PVC V-guide on the running surface, profile 10x6 mm - Includes cut-out in the discharge sheet - Includes slide bushings in the drive and deflection rollers

Condition: new, Year of construction: 2026, Aluminum incline conveyor with substructure including leveling feet and machine feet for compensating uneven floors - Feed height: 500 mm - Inclined section: 2,000 mm - Discharge height: 1,200 mm Design: Dkedpfx Aoyhzhbockjn Aluminum structural construction - Triple-reinforced profile 135x45 mm - Continuous removal plate 2.0 mm galvanized Drive roller + return roller made from S235 steel, welded and machined Ø150x620 mm crowned, shaft fixed with pillow block bearings. Drive: Mounted gear motor 1.10 kW, belt speed 0.77 m/sec Connection 230/400V, 50Hz, protection class IP54 Drive pre-wired up to the motor terminal box (Commissioning must be carried out by qualified electrical personnel) PVC conveyor belt DM 10/2 0+005 PVC green Belt width: 600 mm endless high-frequency welded with stepped joint Belt material: 2-ply, especially cross-stable 2 pcs wave edge profiles, 80 mm high, 50 mm wide, high-frequency welded flush with the belt edge 14 pcs T60 cleats, 400 mm long, pitch approx. 296 mm, center-mounted Belt material: 2-ply, especially cross-stable Due to the wave profiles on both sides, the usable belt width is reduced: Usable width 500 mm, calculated as follows: (Top view) Crosswise arrangement 50+500+50 mm

Condition: good (used), Cast iron marbles Length: 3970 mm Dsdpjh Awqgsfx Ackjkn Width: 2060 mm Useful surface (L x W x H): 3910 x 2000 x 350 mm Delivered with 6 levelling feet Weight: 7 T 2 same plates available.

Year of construction: 2018, condition: as good as new (ex-display), machine/vehicle number: TMA420x280mm, Drum magnet - Magnetic separator in the housing including separating plate, drive and gearbox + high quality stainless steel execution + Separating plate for separation + Shaft bracket in the form of a storage unit + Pillow block units Dimensions: L: 420mm B: 280mm H: 380mm Inlet: 365x80mm Dsdpfx Asdzqxbockskn Drum: Ø 220x400mm

Condition: new, Year of construction: 2025, Overband Magnetic Separator – Type DMPM 2000 | Industrial Version Manufacturer: die magnetprofis GmbH & Co. KG Dsdpfx Aswx H E Dockokn Model: DMPM 2000 Condition: New / unused Availability: Immediately ex stock ⸻ Technical Description: The DMPM 2000 overband magnetic separator is engineered for the reliable and continuous removal of ferromagnetic contaminants from product streams. It is ideally suited for use in recycling plants, bulk material processing, crushing plants, conveyor lines, and material processing facilities. ✅ Key Features: • Design: Cross-belt discharge with motor & discharge belt • Magnet type: Permanent magnet (maintenance-free) • Belt width: 650 mm • Magnet length: approx. 2000 mm • Support structure: Robust welded steel construction • Drive: Electric motor with low-maintenance gearbox • Ready to operate: Pre-assembled, ready for operation, incl. lifting lugs • Options: Control unit in the form of a frequency converter, gallows for suspension ⸻ Fields of Application: • Recycling industry (metal, wood, construction debris, etc.) • Conveyor systems in the cement, energy, or waste sectors • Protection of downstream machinery (e.g., shredders, crushers, mills) • Food industry (optionally available in stainless steel version) ⸻ Scope of Delivery: • Overband magnetic separator DMPM 2000 (new unit) • Conveyor belt with drive unit • Suspension system (chains as required) • Documentation (operating manual, CE conformity) • Optional: Control – frequency converter Our core competence is delivering exactly what our customers truly need. Together with our customers, we develop tailored, application-specific solutions and supply corresponding systems from our own production. Feel free to contact us by phone to find a suitable solution for your application. Conveyor belt, conveyor system, discharge belts, belt conveyor, magnetic separator, overband magnetic separator, recycling, wood chips, plastics, metal-free, metal detection, neodymium, overband magnet, magnetic belt separator, lifting magnets, filter bars, magnetic grids, grid magnets, metal separator, block magnet, filtration systems

Year of construction: 2018, condition: new, machine/vehicle number: DMPMFG200x200, Magnetic filter grid in housing / cabinet construction V2A quality (for free-fall applications to investigate dry and free-flowing bulk solids) Magnetic grid 200x200mm High-quality cabinet construction completely closed Easy cleaning by pulling out the magnetic cores High quality magnetic filter rods completely closed Magnet NdFeB N45, Br 8500 Gauss Tmax 80 ° C 4x M10 threaded rod incl. Wing nut as clamping unit Guide rod center: Dkedpfx Acodtdwajkjn Entrance level right Outlet below

Year of construction: 2015, condition: as good as new (ex-display), machine/vehicle number: 2015020890, For sale is a magnetic filter system with integrated cleaning system. Filter systems of this type are usually made individually to order from customers. In this system, there is an exhibition purpose, which only served to show, and was hardly in use. product benefits Installation possible into existing production lines Separation of any ferrous metal contaminants Dkodpjcwghbefx Ackjn Very corrosion resistant High wear resistance Compact design Low maintenance Technical details - 400 x 400 x 390 mm - Inlet 260x260mm - Inlet 260x260mm - 8 pcs magnetic filter rods