Used Elgo for sale (84)

Condition: used, Year of construction: 1999, sheet width 3060 mm plate thickness 8.0 mm thickness at "Niro-steel" 6.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes max. 10 - 15 Hub/min oil volume 160 ltr. cutting angle 1.6 ° back stop - adjustable 6.0 - 750 mm Control ELGO P9521 total power requirement 18.5 kW weight 6300 kg range L-W-H 3900 x 2300 x 1630 mm Features: - Robust electro-hydraulic swing beam shear - ELGO digital display model P9521, for electric backgauge * Backgauge travel X = 750 mm * Backgauge-free ball screw drive * Travel speed 100 mm/s - 1x stable side stop * With T-slot, flip-stop, and millimeter scale - 2x stable front support arms - Electric cutting length limiter * Cutting length limiter to increase the stroke rate/min. - Manual cutting gap adjustment * Centrally operated on the right side stand - Front support plates - Front finger/interference guard Kjdpfxexaci Ej Ab Todh - Inching operation with push buttons on the left control panel - Protective grille = safety device behind the machine - Operating instructions (PDF)

Condition: used, Year of construction: 2000, sheet width 3060 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes 20 Hub/min oil volume 160 ltr. cutting angle 1.6 ° Control ELGO Number of working hours ~ 1.100 h total power requirement 11.0 kW weight 5250 kg range L-W-H 3800 x 1940 x 1560 mm from a maintenance workshop with only approx. 1.100 operating hours (!!) Equipment: - electro-hydraulic swing beam shears - ELGO NC control unit Kodpfxsxacfae Ab Tjdh * for electric back stop * Input of target/actual position value possible - NC electro-motoric back stop * travel path of back stop X = 750 mm * back stop ball screw with no play * travel speed 100 mm/sec - electric cutting length limitation * cutting length limitation to increase the number of strokes/min. - manual cutting gap adjustment, via eccentric - tip operation with push buttons on the control panel on the left - front support plates with ball rollers - front finger/interference protection - 1x side stop with T-slot & millimeter scale - 2x front support arms - original operating instructions including CE declaration

Condition: used, Year of construction: 2009, sheet width 3050 mm plate thickness 6 mm rear stop 10-1000 mm cutting angle 0,5 - 2,5 ° down holder 20 Stk no. of strokes 14 - 23 Hub/min work height max. 900 mm oil volume 140 l total power requirement 11 kW dimensions of the machine ca. 4000 x 2150 x 1900 mm weight 7800 kg Equipment: - ELGO control unit type P50 - Automatic cutting angle adjustment - Automatic cutting gap adjustment - electric back gauge - Pneumatic sheet holding device - Light barrier behind the machine - 4 support arms - front finger guard - foot switch Kdjdpfsyk Dhxex Ab Teh - Angle stop Operating instructions

Condition: good (used), Year of construction: 1997, cutting diameter 450 mm saw band length 4150 x 34 x 1.1 mm capacity 90 degrees: flat 450 x 480 mm capacity 45 degrees: flat LI 450 x 310 mm capacity 45 degrees: flat RE 450 x 290 mm band speed 35 + 70 m/min work height max. 930 mm total power requirement 2.35 kW voltage 400 V weight 950 kg range L-W-H 2150 x 1150 x 2115 mm well-maintained condition (!!) current new price incl. accessories ~ 50.000 Euro special price on request Equipment: - electro-hydraulic vertical mitre bandsaw - with large cutting range and small footprint - Robust material support table - electro-hydraulic mitre adjustment left right * Only the saw frame swivels, everything else remains fixed * incl. ELGO digital value display - electro-hydraulic material clamping - electro-hydraulic infeed from the saw frame * Infinitely adjustable (cutting pressure control) - Operating instructions Kedpfxoyk Dhle Ab Tedh * Special accessories included : - approx. 3.000 mm feed roller conveyor ... roll width 500 mm - approx. 3.000 mm motorized infeed roller conveyor ... Roll width 500 mm - approx. 6.000 mm outfeed roller conveyor with digital display .. Roll width 500 mm - Micro-dosing device (spray oiler)

Condition: ready for operation (used), Year of construction: 2004, pressure 60.0 t Kdsdew U U Ttspfx Ab Teh chamfer lenght 2600 mm distance between columns 2050 mm column arm 310 mm working feed 10.0 mm/sec return speed 61.0 mm/sec stroke 100 - 140 mm dayligth 450 mm table height 860 mm oil volume 100 ltr. Control ELGO P8822 operating pressure max. 200 bar Number of working hours ca. 2.370 h voltage 380 V total power requirement 5.5 kW weight of the machine ca. 5000 kg. range L-W-H 3000 x 1850 x 2050 mm good / well-maintained condition (!!) with only approx. 2,370 operating hours current new price approx. 60.000 euros special price on request in checked conditions - machine video - ?v=PsUeM3O5wAM Equipment: - NC electro-hydraulic press brake - with ELGO NC control unit "P8822" * Input of target/actual values ??for back stop * Input of target/actual values ??for depth adjustment ` * swiveling operation, front left * manual mode selectable - NC controlled axes: Y1 + Y2 + X - NC electro-motorized back stop, on ball screws * with 4x manually adjustable stop fingers * adjustment in R+Z axis (manual) - Upper tool holder SYSTEM A (AMADA), with upper wedge crowning * 1x split set of upper tools * clamping jaws with clamping lever (quick clamp) - 1x universally rotatable MULTI V die block - 2x side-hinged doors (protective device) - 1x rear sliding door (protective device) - 2x front stable support arms - 1x freely movable foot control (on rollers - movable) - Operating instructions (PDF)

Condition: ready for operation (used), sheet thickness steel (max.): 20 mm, power: 30 kW (40.79 HP), total length: 3,600 mm, total width: 2,350 mm, total height: 2,400 mm, empty load weight: 17,000 kg, workpiece length (max.): 3,100 mm, Type: DS Zware schaar met anti-torsiesysteem! Ksdpfoykcpzjx Ab Tjdh hydraulische zwenkbalk Elgo digitale uitlezing Strokes/min: 5 > 9 str/min Adjustable cutting device: 2°30' Number of sheet holders: 15x

Condition: used, functionality: fully functional, Year of construction: 1986, control type: NC control, Hydraulic Press Brake Make: AMADA Type: FBD-1030 Year: 1986 Technical Details Manufacturer: AMADA Type: FBD - 1030 Year of manufacture: 1986 Working length: max. 3100 mm Between frames: 2700 mm Pressing force: 100 t Stroke: 100 mm Connected load: 8.7 kVA Dimensions: approx. L 3.50 x W 1.50 (plus support arms) x H 2.45 m Weight: 7,150 kg Equipment • Depth penetration adjustment with digital display • 2 support arms, retractable • Manual Amada tool clamping, top and bottom • Elgo control Kdedpfxsx H R U Eo Ab Tsh • Safety light curtain for rapid traverse • 4 back gauge fingers, manually adjustable laterally and in height • NC back gauge • Upper tool, lightly goosenecked, 88°/R0.8, segmented • Lower tool: 4-way block die V35, V50, V16, V20, segmented All information without guarantee. A demonstration is possible at any time in our showroom.

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized Motor power: approx. 30 kW Power supply: 400 Volts, 50 Hz - Backgauge with ELGO positioning control - Backgauge adjustment via ball screws - SICK safety light curtain at the front as reach-in protection - 3 material support arms with ball transfers Kdodped Hxx Ajfx Ab Tsh - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Very robust machine with extremely solid construction Machine footprint (L x W x H): 4650 x 2610 x 3200 mm Machine weight: 27,000 kg Transport dimensions (base machine) (L x W x H): 4650 x 2610 x 3200 mm Transport dimensions (additional) (L x W x H): 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau, test cuts possible. Currently, the hold-down devices are being resealed; the resulting price adjustment will be made in the coming days.

Condition: used, total length: 6,400 mm, Weight: 17.500 kg Price: On request - Documentation available: Yes - CE certificate present: No - Serial number: 13707 - Drive system: Conventional - Control system brand: Elgo - Drive type: Hydraulic Kedpfxownhp Nj Ab Todh - Power [kW]: 11.0 - Max. sheet thickness [mm]: 6 - Max. working width [mm]: 6200 - Throat depth [mm]: 60 - Backgauge depth [mm]: 1000 - Transport weight [kg]: 17500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Bram van Summeren

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1998, TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 3100 mm Kdedpfxeyag Uao Ab Teh Range back gauge 1000 mm Min. cutting angle 0.5 ° Max. cutting angle 3.5 ° Number of sheetholders 17 Min. number of strokes/min. 6 Max. number of strokes/min 30 Min. blade clearance 0.1 mm electric powerd back guage with elgo "go-to" controller plate following system at back guage

Condition: used, functionality: fully functional, Year of construction: 1987, machine/vehicle number: 101536, Offered for sale is a hydraulic guillotine shear Manufacturer: Eisen und Hammerschmidt GmbH Model: TSS4-20 Year of manufacture: 1987 Serial No.: 101536 Capacity: 4 mm Working width: 2,000 mm Control: ELGO Type P8511 Light curtain system by SICK Used, fully functional condition. Collection by purchaser; assistance with dismantling/transport can be arranged if required. — If you are interested or have any questions, please feel free to send me a message. Viewing on site by appointment possible. Further metalworking machinery such as bench drills, press brakes, column drilling machines, eccentric presses, heavy-duty racking, welding tables, MIG welders, compressors, etc. – please take a look at my other listings. Location for viewing and collection: 12277 Berlin Domestic price net plus VAT or Net export price Kdedsx Da D Ujpfx Ab Toh Collection only – dismantling and transport by buyer or by arrangement. If you are interested or have any questions, please feel free to send me a message. Further photos and technical details available on request. All information is subject to change without notice. Errors and prior sale reserved. For further questions, please call Nous parlons Français / Мы говорим по-русски We speak English / Noi vorbim românește Viber / WhatsApp / Skype We handle all customs and registration matters for an additional charge. For an extra fee, we can transfer the vehicles to the port.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2021, machine/vehicle number: 2107308, controller model: Elgo P40T, working width: 3,100 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, sheet thickness (max.): 13 mm, The machine was only in use for 3 years! The original price was €52,000! TECHNICAL DETAILS Working width: 3,100 mm Cutting angle (min.): 0.5° Cutting angle (max.): 3° Stroke rate (min.): 8 strokes/min Stroke rate (max.): 20 strokes/min Sheet thickness (max.): 13 mm Aluminum sheet thickness (max.): 10 mm Steel sheet thickness (max.): 13 mm Stainless steel sheet thickness (max.): 8 mm Kdjdpjydc Nbsfx Ab Toh Back gauge adjustment: CNC controlled Back gauge: 1,000 mm MACHINE DETAILS Control: Elgo P40T Dimensions & Weight Total weight: 12,000 kg Dimensions (L x W x H): 4,000 x 2,200 x 2,100 mm Power: 22 kW Input voltage: 400 V Input current: 45 A Input frequency: 50 Hz Type of input current: Three-phase EQUIPMENT CE marking Finger guard Foot remote control Emergency stop button Safety light curtain

Year of construction: 2003, operating hours: 3,542 h, condition: ready for operation (used), This EHT ECOCUT was manufactured in 2003. A robust hydraulic shearing machine, it features a cutting length of 3,050 mm and a thickness capacity of 13 mm. It operates with an 18.5 kW main motor and includes an ELGO P8511 control for precision. Consider the opportunity to buy this EHT ECOCUT hydraulic shearing machine. Contact us for more information. • Cutting capacity: • Cutting length: 3,050 mm • Cutting thickness: 13 mm • Material tensile strength: 450 N/mm² • Hydraulic system: • Oil volume: 300 liters • Electrical data: • Current type: AC • Frequency: 50 Hz Kedpfxjycfq Ss Ab Tsdh • Operating voltage: 400 V • Control voltage: 24 V DC • Rated current: 45 A • Main fuse rated current: 63 A • Main motor power: 18.5 kW • Control / documentation: • Control type: ELGO P8511 (NC backgauge control) • Electrical circuit diagram no.: 111 796

Condition: used, Hydraulic Plate Shear LVD Type HST-C 31 / 6 Machine No. 21348 Year of manufacture: 1994 Cutting length: 3,100 mm Cutting thickness: 6.35 mm Backgauge: 770 mm Working height: 950 mm Hydraulic sheet hold-downs: 17 units Hydraulic tank capacity: 150 liters Motor power: 7.5 kW Power connection: 400 Volt, 50 Hz, 9.5 kW, 19 Amp. - Motorized backgauge with digital actual position display ELGO - Backgauge adjustment via push button – rapid in both directions and fine adjustment by jogging in the minus direction only - Sheet lifting device below the backgauge with pneumatic lifting cylinder - Continuously adjustable blade gap from 0.1 mm via handwheel with analog display - Cutting angle adjustment in 5 steps from 1.5° to 3.5°, electrically pre-selectable - Left side angle stop 1,500 mm Kedpfx Ajtvb Iusb Todh - 2 table extensions as sheet supports - Electric foot switch - Comprehensive operating manual Space requirements without front table extension (L x W x H): 4,150 x 1,850 x 1,900 mm Space requirements with front table extension (L x W x H): 4,150 x 2,850 x 1,900 mm Weight: 5.5 tons Good condition Very good cutting results, including with thin sheet metal

Condition: used, Year of construction: 2003, pressing force: 120 t, overall weight: 12,000 kg, Hydraulic Press Brake Brand: Hidrogarne / Ermaksan Model: AP 4100-120 Kodpfxex Tp Auo Ab Todh Year: 2003 Power: 11KW Weight: 12,000kg Bending length: 4100mm Force: 120t Approach speed: 80mm/s Working speed: 8mm/s Y-axis and X-axis back gauge control with ELGO control system. PROMECAM punch holder. Supplied with: - 4m one-piece die, 90x90mm with several V openings - 4m gooseneck punch, 90mm height, in 835mm sections and some additional smaller pieces - Also comes with sets of straight and 30-degree punches (see pallet photos of punches)

Condition: excellent (used), Year of construction: 2005, I sell the thin cutting mini frame saw gatter NEVA TR88 Orbit plus, year 2005. Configuration with top + bottom moulding heads 1,5 + 1,5 KW suitable for later lamellas gluing Main motor 15 KW Working height 270mm Digital working height adjustment w. ELGO Electric Positioner Digital feedign speed adjustment w.MKS Total weight 2800kg. Lot extras, saw leafs, adjustment elements and frame adjustment device indluded. Very good condition. Fully working. Made in Czech republic. Kodeiuc Scjpfx Ab Todh

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display - Manual cutting gap adjustment Kedpfx Aouagxpob Tsdh - 1x side stop with mm scale - 2x support arms - 1x freely movable double foot switch - Front finger guard Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

Condition: used, Year of construction: 2008, sheet width 3100 mm plate thickness 6 mm rear stop 1000 mm cutting angle 1,2 ° down holder 14 Stk no. of strokes 18 Hub/min oil volume 150 l total power requirement 11 kW dimensions of the machine ca. 3900 x 1900 x 1600 mm weight 5500 kg Equipment: - Hydraulic swing cut shears - ELGO control system - Electric backgauge 1000 mm Kdodpfx Abjvuz Tpj Tsh - Manual cutting gap adjustment - Cutting length limitation - Ball rollers in the table - 2x front support arms - 1x front side stop with scale - Front finger guard, hinged - Rear safety device (protective grille + light barrier) - Foot switch - Operating instructions

Condition: used, sheet width 4080 mm plate thickness 2.0 mm ST thickness at "Niro-steel" 0.8 mm Sheet thickness for ALU 2.5 mm cutting angle 1.3 Grad no. of strokes 34 Hub/min distance between columns 4310 mm back stop - adjustable 15.0 - 750 mm table height 820 mm Control ELGO Kdodpfx Absxabc Rs Toh engine output 9.0 kW weight of the machine ca. 3600 kg. range L-W-H 5250 x 2200 x 1400 mm Good condition (!!) Current new price approx. €70,000 Special price upon request The MHSU motor-driven guillotine shear is based on a torsion-free, rigid welded construction and a dynamic, quiet, and powerful gear motor. High static and dynamic rigidity is ensured by robustly dimensioned main components such as the cutter bar, support table, side supports,and the main drive unit. The motor- driven guillotine shear was developed forsheet metal and plastics processing. With these shears, you can effortlessly produce clean cuts in series. Features: - NC robust, motorized swing cut guillotine shears - with ELGO NC control unit * Digital position display of the backgauge * Adjustable from the front right * With target/actual value input * Continuous adjustment across the entire travel range * Limit switch protection - NC motorized material/backgauge - Shatter-proof, torsion-free welded steel construction - Compact and clearly arranged machine design - Support table with recessed grips - 1x hold-down bar - 1x side stop with T-slot and scale - 3x front support arms - 1x freely movable foot switch - Operating instructions Optional accessories included: - Pneumatic sheet metal holding device for thin sheet metal blanks

Condition: used, Year of construction: 1990, plate width 2503 mm plate thickness 4.0 mm ST plate thickness 2.5 mm VA plate thickness 6.0 mm ALU number of strokes - loaded 15 - 20 Hübe/min cutting angle 1.7 ° work height max. 900 mm Control ELGO TYP 85 total power requirement 8.5 kW weight of the machine ca. 3400 kg range L-W-H 2913 x 2250 x 1760 mm Features: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge * with ELGO control unit - Manual cutting gap adjustment - Front support table including recessed grips - 1x sturdy side stop with scale and tilting cam - 2x sturdy front support arms - 1x freely movable foot switch - Front finger guard - Front emergency stop button Kdjdpfx Aexabd Uob Tjh - Operating instructions (PDF)

Condition: used, Year of construction: 1985, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts Ksdpfx Aoxab Tvsb Tjdh - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Condition: good (used), Year of construction: 1991, sheet width - max. 1010 mm plate thickness 4.0 mm ST plate thickness 2.5 mm VA Kdodoxrgv Topfx Ab Teh plate thickness 6.0 mm ALU number of strokes - loaded max. 20 Hübe/min cutting angle 1.5 ° work height max. 900 mm Control ELGO back stop - adjustable max. ~ 1.000 mm total power requirement 5.5 kW weight of the machine ca. 2200 kg. range L-W-H 1500 x 2155 x 1606 mm from a maintenance workshop good condition (!!) - in checked conditions - machinevideo - ?v=w22S17mfU-A Equipment: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge * Includes NC ELGO positioning control "TYP 85" - Electric cutting length limiter - Manual cutting gap adjustment - 1x side stop with scale - 2x support arms - 1x freely movable foot switch - Original operating instructions * Special accessories included: - Pneumatic holding device for thin sheet metal blanks

Condition: ready for operation (used), Year of construction: 1997, sheet width 3230 mm plate thickness 2.5 mm thickness at "Niro-steel" 1.5 mm no. of strokes 28 - 42 Hub/min cutting angle 1.60 Grad table height 820 mm distance between columns 3540 mm Kdsdpfexacd Nox Ab Tsh Control ELGO 87P engine output 6.8 kW weight of the machine ca. 3410 kg. range L-W-H 4070 x 2070 x 1400 mm from a maintenance workshop including special accessories (!!) Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - NC electro-motorized back stop - including NC ELGO "TYP 87P" digital control unit * adjustable from the front right * with target/actual value position input * continuous adjustment over the entire travel range * rough adjustment via push buttons * protection of the limit values ??with limit switch - "Duo-Cut" drive with two dynamic, powerful gear motors - support table with recessed grips - hold-down bar with hard rubber strip - all-steel knife with two cutting edges - selector switch for single and continuous stroke - 1x freely movable foot switch - safety device at the rear - original operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts - 1x extra long side stop, including support foot + digital stop - 2x extra long, front support arms * with "SLIDING" mount - for easy moving

Condition: ready for operation (used), Year of construction: 2009, pressure 35.0 t chamfer lenght 1250 mm distance between columns 1070 mm piston stroke 150 + 60 mm column arm 410 mm table height 800 mm dayligth 470 mm working feed 10.0 mm/sec return speed 70.0 mm/sec table width 140 mm Control ELGO NC Number of working hours ~ 9.600 h oil volume 80.0 l operating pressure max. 240 bar voltage 380 V total power requirement 4.0 kW weight 2200 kg range L-W-H 1800 x 1450 x 2150 mm Well maintained condition With only approx. 9.600 operating hours (!!) - in checked conditions - machine video - ?v=FTOUZ-ModXQ Features: - Robust NC-controlled hydraulic press brake - With ELGO NC control unit “P8822” * Positioning of the backgauge (X axis) * Positioning of the depth adjustment (Y1+Y2 axis) * Swiveling control panel, front left - NC electric motorized backgauge (X axis) * With 2x stop fingers, manually adjustable (R+Z axis) - 1x split set of pointed tools - top - 1x rotatable Multi-V die block - Side safety device (swivel doors) + FIESSLER laser safety device Kedpox Avqzjfx Ab Tsdh - Rear safety device (swivel door) - 1x freely movable double foot switch - 2x front support arms - Operating instructions (ENG)

Condition: new, Year of construction: 2025, Available in following capacities: 1100 x 4/1100 x 5/1100 x 6 mm 1370 x 4/1370 x 5/1370 x 6 mm 1600 x 4/1600 x 5/1600 x 6 mm 2100 x 4 2600 x 4 mm 3100 x 4 mm Standard features: -NC controlled backgauge 750 mm with recirculating ball spindles -NC controller including cutting counter -Single cut, continuous cut and inching mode changeover -mobile foot switch with EMERGENCY STOP Angle stop on the left side with T-track -Table extension -Roller balls in the table -manual cutting gap adjustment from the front -Cutting line lighting Kdedpogu N E Dsfx Ab Tsh - All-steel knife 2-edged - Sheet metal hold-down device with hard rubber strip to protect polished sheets -Light curtain on the back of the machine instead of a safety grille (CE) -Foldable front security grille (CE) -Optical function display on the front of the machine -CE conformity -2 years full guarantee -3 years on engine and gearbox Optional accessories: -Adjustable angle stop with degree scale and mm graduation -pneumatic sheet metal holder -ELGO 9521 NC controller -Sheet ejection to the front - Sheet ejection to the front including a pneumatic sheet holding system (optional sheet ejection to the front or back over the entire cutting length with NC controller FUJI touchscreen (return to sender) -Table extension with tilt stop and T-slots -Special knife for VA steels -Special color on customer request