Used Fabrik for sale (139)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Cedpfx Aex A U Ncjgcjaa Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: as good as new (ex-display), Semiconductor protection Make Klöckner Moeller Type DIL SM 16 V-k 400 Volt 16 A 7,5 kw unused from stock Cajdpfjmxi U Ssx Agcsa

Condition: used, Year of construction: 1978, Technical details: table surface area: 1970 x 400 mm distance between table/spindle: min./max. 150 / 250 mm rapid traverse: 1 / 2 m/min revolution per minute: Frässpindel: 112 ... 1400 / 12 step U/min milling spindle taper: DIN 2019 = Nr. 40 (SK40) axial adjustment: manuell = 150 mm quill feed: 0,012 / 0,025 / 0,05 mm/U feed range - horizontal: Frässchlitten: 8...100 / 12 step mm/min total power requirement: ca. 8,4 (10,5 kVA) kW machine weight approx.: 3000 kg dimension machine xH: 3,05 x 2,7 x 2,0 m wedge-groove milling machine Application: Milling of straight and helical grooves. Multiple groove milling with automatic program sequence. Further features: - distance spindle axis / lower edge counterholder: 55 mm - axial movement of the counter bearing sleeve 50 mm - milling carriage movement horizontal 1000 mm (automatic + manual by hand) and vertical 100 mm by hand + max. 5mm automatic/hydraulic Equipment: - chip container 470x300x300mm Cedpfxsu Ndhis Agceaa - 2x oil collecting basins (3200x1500x70 and 3200x800x60mm) - some accessories/tools *

Condition: used, Year of construction: 2017, functionality: fully functional, CHIP CONVEYOR 1200MM Hinged belt conveyor with discharge height approx. 1200mm, suitable for: Cajdpfsx A Dn Ujx Agcsa • Long steel chips • Chip nests • Wool chips For dry and wet machining Free loading Available immediately

Year of construction: 1950, condition: excellent (used), Article number: MA 994 Manufacturer: VEB Waggonfabrik Gotha / Lev - VEB Lokomotivbau Hennings village Type: BZ 57 - two leadership Year: 1957 Length [m]: 10.9 bulkhead / total length 12 m Width [m]: 2.2 Height [m]: 3.115 Weight (kg]: 8400) Cajdpfsdwd Dmox Agcoa Seats: 22 Standing passengers: 83 Axles: 2 Doors: 4 doors Other: documentation

Condition: good (used), Power: 16 KVA Cjdpfx Agshc Syzscjaa

Condition: used, Cutting force of 10 tons Sheet thickness up to 3.15 mm Casdpfxoxxz Haj Agcsa Maximum material strength: 50 kp/mm²

Year of construction: 2025, condition: new, functionality: fully functional, A total of 450 unused Big Bags are available for sale. Each pallet contains 150 units. Delivery on pallet is possible for an additional freight charge. Quality and specifications: Big Bags, form-stable, uncoated, SWL (safe working load) 1250 kg, SF 6:1, 200 g/m², top open, bottom closed, 4 lifting loops, each 25 cm in length, overhang, UV-stabilized Casdpfexr Dm Ajx Agcea on EWP approx. (100x120x100 LxWxH) Dimensions: approx. 101x101x200 cm (external dimensions) No individual bag sales—only by full pallet! The above price refers to one pallet (150 units).

Condition: used, Year of construction: 1977, Technical details: honing diameter: 125 mm Casdpfxjw Rv Tao Agcea stroke: 500 mm throat: - mm grinding spindle speed: 26-1200 (12Steps) U/min honing diameter: 30 (min.) mm honing diameter: 165 (max.) mm table adjustment:: 800/150 (max.) mm table surface area: 500 x 1000 cm total power requirement: 4,22 kW Weight approx.: 0,15 t dimension machine xH: 1,30 x 1,20 x 2,70 m There is a movable table that moves lengthwise and crosswise. *

Condition: good (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 6860 0007, Please let us know your quote. Sale only within the European Union (EU), including Switzerland, Turkey, and Great Britain ----- Scope of delivery: Machine, loading system, conveyor belt, workpiece carrier Machine specifications: 5-axis grinding center including oval feed belt and loading gantry 12-station tool changer with HSK 63 Max. X-axis travel: 500 mm Max. Y-axis travel: 650 mm Max. Z-axis travel: 650 mm Table size: 500 x 650 mm Cut-off detection Nordmann dressing spindle Oil supply via central factory supply Caedpsvbgiiofx Agcja

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Cajdpfxju Thbxe Agcsa Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Clamp holder make Comet FG IIII (28396) for Comet threaded steel FG IIII TR 12 Csdpfx Aomk E Uiegcoaa

Condition: good (used), Year of construction: 1980, functionality: fully functional, STC-Ref:G-791-0121 Karl Mayer-Web-Wirk machines ,Year: 1980 format width: 12 Zoll, 4,06 mtr equipped: - für Schattennetze - material width max. 160 Zoll, 4,06 mtrs. - type: R 4 n1 M-FSM - grammature 70 g/qm - 180 g/qm - many spare parts included - GANG753 Casdpfx Aot Rhykogcsa --> available: 11/2024

Year of construction: 1979, operating hours: 216 h, condition: reconditioned (used), functionality: fully functional, Twin-screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine no.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. 30 rpm Screw torque: 10000 Nm Motor power: 3.3 - 25.0 kW Caedpfx Aexlcfksgcoa Drive motor: commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool heating zones: 8 Temperature control: 12 x digital temperature controllers (PMA KS40) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tool) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material hopper and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hopper Weight: approx. 4000 kg Note: The electrical control cabinet was completely renewed approx. 3 years ago. Since then, the extruder has only been in operation for 216 hours. Condition: The extruder was repainted (light gray, RAL 7035) and checked for function.

Condition: used, Year of construction: 1999, Technical details: Codpfx Agou Idl Secoaa x-travel: 690 mm y-travel: 400 mm z-travel: 550 mm B-axis (table): 360° mm control: Siemens 840 D number of spindle speeds: max. 15 000 U/min tool clamping: System nach DIN 69893 tool taper: HSK-A63 tool changer magazine: chain magazine: 12 places Stück traversing speed: x/y/z Axis: 40 total power requirement: 195 kW weight of the machine ca.: 13,0 t Traveling Column Milling Machine - the tool changing unit consist of 3 -NC axis and 1 NC- rotary table axis - ATC ( with magazine) - rotary table Type SKH-NC 4/029, diameter=460mm , table surface plate Ø 500 x20mm, revolution per minute max. 22 rpm - control panel SIEMENS - Spindel-Typ: DRF-WE-255-N-W-15-30, 15000 U/min., Spindelleistung = 30 kW - chip conveyor Make Knoll type 400K-3/280, ejection height 1150mm - cooling system for spindle make SCHIMBKE Type DK 80V, 3,36 kW i.D. *

Year of construction: 2017, condition: ready for operation (used), Belt length: 2900 mm belt width: 360 mm Belt speed infinitely variable drive motor table height adjustable by: +/- 500 mm Caodpjdzx E Uofx Agcja space requirement: 2000 x 600 x 650/700 mm

Condition: excellent (used), Year of construction: 2018, Converting Line GM 330 FB-D (Hot stamping + Screen printing) Year of manufacture: 2018 Manufacturer: Grafisk Maskinfabrik Maximum web width: 350 mm Minimum web width: 50 mm Maximum unwind diameter: 700 mm Maximum rewind diameter: 600 mm - Vetaphone Corona Treater - BST Web Guiding System Hot Foil Stamping Unit (Flatbed) Speed: 6,000 impressions/h or 10-15 m/min Web width: 110 mm - 330 mm Dual foil unwind and rewind with 250 mm diameter Substrates: 50–500 µm Plate thickness: 5-10 mm (7 mm standard) Stamping pressure: 30 tons Foil feed in both transverse and longitudinal direction (rotatable turret) Temperature range: 80° - 130° C Heating time approx. 20 min. Screen Printing Unit Cedpow I T Ucsfx Agcjaa Speed: 4,000 cycles/h or 5-15 m/min Web width: 110 mm - 330 mm Frame size: 660 mm x 500 mm Frame type: 30 mm x 30 mm aluminum frame Printing area: 330 mm (length) x 330 mm (width)

Condition: like new (used), Previous Next MFL CJ 108/80 Jaw Crusher “MFL CJ 108/80” for Sale Manufacturer: Maschinenfabrik Liezen G.M.B.H. Type: CJ 108 / 80 Mach. No.: 95 395 103 Inlet size: 1.080 x 800mm Electrical Motor: Included Csdpfx Aoglvx Tsgcjaa

Condition: as good as new (ex-display), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 15194, tank capacity: 2,000 l, Laska mixer in very good condition… Caedpoxbbkdefx Agcja

Condition: used, Sprout and miter punch, sprout punch Caodpfx Aeif Huregcea -Manufacturers: ram factories, mechanical corner punch -Intermediate size: 100 mm -Adjustment depth: 65 mm -Dimensions: 1700/600/H1080 mm -Weight: 118 kg

Condition: used, Year of construction: 2004, Technical details: x-travel: 1500 mm y-travel: 1000 mm z-travel: 1000 mm control for program: TNC 530 spindle hours: noch nicht bekannt h milling head speed: 1: 30 bis 930 und 2: 930 bis 4000 / steples U/min tool taper: horiz./vertical: SK 50 (DIN 69871/Din 69872 Form A) max. torque on the spindle: 1000 Nm spindle head swivable left - right: 90 ° feed: 1 - 6000 mm/min feed power: 30 kN kN rapid traverse: 15 m/min Number of tools: 1 St. table clamping surface LxW: 1600 x 800 mm table load: 40 kN kN voltage: 400 V / 50 HZ V total power requirement: 42 kW Casdpfxsu Nc Rie Agcea Weight approx.: 15,2 t dimension machine xH: 3,1 x 4,7 x 2,6 m dimensions: Kühlfilter: 1,9 x 1,6 x 1,4 mm space requirements approx. LxWxH: ca. 38,5 m² m² compressed air: 6,3 bar Applications: Milling, drilling; tapping, boring. with direct coded length measuring systems the guideways of the 3 axes are on flat guideways CTS and external cooling Milling head position controlled +/-90° milling spindle nominal drive power 22 kW with integrated hydraulic power unit up to 100bar operating pressure with coolant unit with filtration, with high pressure pump 60 bar (internal cooling), nominal delivery 20 l/min. and low pressure pump 4 bar (external cooling) as well as spray gun Hinged belt chip conveyor DGS, type SSF 600 P50 Accessories: Measuring probe SK40 Reference tool SK40 Milling head SEMPUCO *

Condition: used, three-jaw chuck, three-jaw lathe chuck -Manufacturer: SCA Skand Chuckfabriks, precision three-jaw chuck chuck size Ø 230 mm -Jaws: individually and fully adjustable -Passage: Ø 66 mm -Bolt circle: Ø 193 mm / M12 -Dimensions: Ø 230 x 130 mm Codjux Safepfx Agcjaa -Weight: 21.2 kg

Condition: used, Technical details: weight of the machine ca.: 4,0 t machine dimensions LxWxH: 1,8 x 1,8 x 0,9 m Caodpsu N D S Ujfx Agcea Machine table with 5 indexing tables for multi-side machining Application: Multi-side machining of workpieces in circular transfer machines in one operation on 5 indexing tables with clamping devices. Design: Round, fixed body with 5 round tact tables, which are arranged in the shape of a pentagon, and a centrally mounted turntable. Description: Turntable center = type Pentagon, diagonal 830mm; swing diameter Ø 873mm, side length 513mm 5x rotary indexing table, as a regular pentagon on machine body, center circle Ø = 1280mm, table shape truncated square 380x380mm, clamping device via 4 pieces make Röhm truncated cone clamping devices and 1 central centering flange, 360 ° rotatable, workpiece Ø approx. 730mm Actuation / drive is hydraulic *

Condition: used, three-jaw chuck, three-jaw lathe chuck -Manufacturer: SCA Skand Chuckfabriks, three-jaw chuck chuck size Ø 110 mm -Passage: Ø 25 mm -Bolt circle: mm -Dimensions: Ø 110 x 115 mm -Weight: 4.8 kg Codpfx Agjuypyljceaa

Condition: used, Test pump, pressure test device, measuring device, pressure test pump Caedpfx Agsfnaaijcoa -Manufacturer: Junginger, mobile extraction device -Pressure display: 40 bar -Dimensions: 790/480/H775 mm -Weight: 47 kg