Used Faccin Rcmi 110 for sale (31)

Condition: excellent (used), Year of construction: 2013, controller manufacturer: ELFRAN Digital Read Out, number of rollers: 3, shaft diameter: 130 mm, overall weight: 5,800 kg, total length: 2,200 mm, total width: 2,400 mm, total height: 2,000 mm, Profile bending machine FACCIN - RCMI 130 MACH-ID 9451 Make: FACCIN Type: RCMI 130 Control: ELFRAN Digital Read Out Year: 2013 3 rolls driven 2 lateral guide rolls Digital readout for position rolls Set hardned universal rolls Set hardned profile rolls Horizontal and vertical:|Horizontal and Vertical Shaft Ø: 130mm Number of rolls: 3 Capacity flat: 240 x 30 x 1000mm Bdodpjyrq Dvsfx Ab Uea Capacity Tube: 140 x 5 x 1500Ø x mm Capacity bar: 80 x 80 x 900mm Capacity T-Profile: 140 x 15 x 1400mm Capacity HEA-Profile: 160 x 1700mm Working speed: 0 - 6000mm/min. Side supports: 2 x Hydraulic side arms Length: 2200mm Width: 2400mm Height: 2000mm Weight: 5800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, functionality: fully functional, Year of construction: 2026, RCMI 280 Three-roll profile bending machine Technical characteristics: Section modulus 720 cm³ Main shaft diameter 280 mm Side shaft diameter 280 mm Outside diameter of the bending rolls 720 mm Adjustable rolling speed 0-4 m/min Bdodpeiivhdjfx Ab Uea Installed power 44 kW (60 hp) Weight 34,000 kg Standard equipment: Hydraulic adjustment of the side rolls 3 rolls powered (3 hydraulic motors + 3 planetary reduction gears) Independent lateral profile guide rollers, adjustable in 6 directions, fully hydraulic Automatic scope rotation speed compensation Complete universal rolls set for standard profiles and beams (12 pieces) Tool kit for machine equipment Low-voltage control on mobile operator panel Safety device according to regulations Technical documentation and CE certificates Digital displays for the rolls position of the side rolls

Condition: new, functionality: fully functional, Year of construction: 2026, Technical characteristics: Section modulus 100 cm³ Main shaft diameter 130 mm Side shaft diameter 130 mm Outside diameter of the bending rolls 410 mm Adjustable rolling speed 0-6 m/min Installed power 18.4 kW (25 hp) Length 1,900mm Width 2,200mm Height 1,900mm Weight 5,720 kg Standard equipment: Hydraulic adjustment of the side rolls 3 rolls driven (3 hydraulic motors + 3 planetary reduction gears) Independent lateral profile guide rolls, adjustable in 6 directions, fully hydraulic Automatic scope rotation speed compensation Complete universal rolls set for standard profiles and beams (12 pieces) Bedpfxsd Eqg Ne Ab Uoda Tool kit for machine equipment Low-voltage control on mobile operator panel Safety device according to regulations Technical documentation and CE certificates Digital displays for the roller position of the side rollers Optional, installed: Siemens NC control PGS-CLASSIC

Condition: excellent (used), functionality: fully functional, control type: CNC control, Thank you very much for your inquiry regarding the Faccin 4-roll CNC bending machine, which has seen very little use. The machine will be sold soon due to internal restructuring. It is in excellent condition. Electronically controlled, hydraulic four-roll bending machine Manufacturer: FACCIN, Model 4 HEL/2122 Technical specifications: Number of rolls: Four Roll geometry: Linear guides Working width: 2000 mm Top roll diameter: 225 mm Bottom roll diameter: 215 mm Side roll diameter: 165 mm Pressing force on the top roll: 100 tons Rated power requirement: 9.2 kW (12.5 HP) Rated maximum rolling speed: 4–8 m/min Machine weight: 4,450 kg Length: 3,500 mm Width: 1,200 mm Height: 1,100 mm Guaranteed performance: For a yield strength of 260 N/mm²: Rolling capacity (full working width): 11 mm Bending capacity (full working width): 8 mm from a minimum pipe diameter of 1,100 mm Rolling capacity (full working width): 8 mm Bending capacity (full working width): 6 mm from a minimum pipe diameter of 286 mm Standard features: Double linear guide system for roll movement Extra-wide bearing blocks MCS double bearing system for roll rotation Extra heavy-duty, double-articulated joint bearings EPS parallelism system Bdodpsywk Uyofx Ab Usa Hardened rolls for high wear resistance All rolls ground after heat treatment Siemens S7 PLC control PGS-CLASSIC control with Siemens touch panel High-quality hydraulic and electrical components Safety pull-cord with emergency stop and CE certification Central lubrication Cone bending device The machine will be available for sale from the end of April.

Condition: new, neu ca. 2 Wochen ab Auftragse Italien 2000 mm 11 mm 11 mm 7 mm 8 mm 6.4 mm 225 mm 215 mm 165 mm 8 m/min 3950 mm 1200 mm 1200 mm 4450 kg Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Bdodpoypbp Rofx Ab Usa Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear guide for the movement of the lower rolls Ultra wide rolls blocks "MCS" bearing system for the lower rolls (4 large bearings on each shaft) Central lubrication system Pressure manometer for constant pinch roll control Extra torque and special braking system Safety cord with emergency stop Equipped according to "CE" regulations OPTION: CNC control Siemens PSG-Absolute with 15" touch screen (automatic calculation of the process for simple and complex shapes)

Condition: excellent (used), Year of construction: 2008, Technical data: Working width: 3100 mm Bending capacity: 16.0 mm Pre-bending: 12.0 mm Top roll diameter: 310 mm Center roll diameter: 320 mm Side roll diameter: 240 mm Conical bending device via tilting of both side rolls Hardened rolls Mobile control panel with digital display Motor power: 15 kW Bedpfxoytr Rmo Ab Ujda CE marking Dimensions (L x W x H): approx. 5100 x 2100 x 1800 mm Weight: approx. 12.5 t The seller is not liable for typographical or data transmission errors. The machine's appearance, technical condition, and wear are consistent with its age; used machines are sold without any warranty.

Year of construction: 2018, condition: good (used), Make: FACCIN Type: 4HEL 3590 Control: Siemens TOUCH Year: 2018 Specifications Metric US Standard Rolling width 3500 mm Rolling thickness 3x toproll Ø 80 mm Bedpfx Aokvm Nfjb Ueda Rolling thickness 5x toproll Ø 110 mm Rolling thickness prebending 90 mm Top Roll Ø 900 mm Top Roll Ø 900 mm Bottom Roll Ø 800 mm Side roll Ø 600 mm Number of rolls 4 Rolling speed 0-6 Adjustiment lower roll 0-200 mm/min. Adjustment side rolls 0-400 mm/min. Top support yes Side supports yes Number of driven rolls 2 Power 90+75+9 kW Dimensions (Estimate) Length 4430 mm Width 8800 mm Height 11000 mm Weight 178000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2002, condition: excellent (used), Technical data: working width: 3550 mm max. bending capacity: 42,0 mm Bodpfoittzfjx Ab Usda max. bending: 35,0 mm CNC control diameter upper roller: 480 mm diameter 2nd top roller: 540 mm diameter lateral side rollers: 480 mm diameter middle bottom roller: 480 mm conical bending device by inclination of the two side rollers mobile control panel with digital display hydraulic folding bearings own weight: approx. 44 tons additional equipment: lateral bending aid swiveling bending aid on top additional top roller The seller is not liable for writing or data transmission errors. The machine is in appearance, technique and wear according to the age; used machines are sold without any warranty.

Condition: used, functionality: fully functional, Year of construction: 1998, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 3, roller (top) diameter: 380 mm, side roll diameter: 340 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 900 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, overall weight: 15,000 kg, total length: 5,500 mm, total width: 1,500 mm, total height: 1,600 mm, power: 22 kW (29.91 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 3, Equipment: centralized greasing system, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, Plate roll FW model HAV 3100X16-30 variable geometry 3-roll plate bending machine capacity 3000 x 30 mm Year of make 1998 Used machine in working condition Top roll 380 mm Side rolls 340 mm Rolls surface length 3100 mm Bdodpfx Aoydiq Seb Uea Capacity bending Plate width 3000 mm Plate thickness 30 mm Prebend 16 mm minimum rolling diameter starting from ID 450 mm and above -configuration -machine fully hydraulic operated -variable geometry of the 3 rolls with pinch prebend -hardened surface of the 3 rolls Rerolling system for calibration of welded plates Front open drop-end to unload the closed shell -Side arm hydraulic swing-down to align the plate in the rolls -hydraulic driven rotation of the upper roll with braking system Control console centralized electric with digital position readout Electric motor power 22Kw installed on hydraulic unit Voltage 3 phase 380/50 Safety and emergency stop installed Manuals operation and service original the machine Machine weight 15ton overall dimension cm 550 x 150 x H160 cm

Condition: excellent (used), Year of construction: 2006, Technical Data: Working width: 2100 mm Bending capacity: 28.0 mm Pre-bending: 22.0 mm CNC control Top roller diameter: 350 mm Middle roller diameter: 330 mm Side roller diameter: 240 mm Bjdpfx Asx Dtt Aeb Usda Hardened rollers Conical bending device via tilt adjustment of both side rollers Mobile control panel with digital display Motor power: 7.5 kW CE marking Dimensions (L x W x H): approx. 3600 x 1500 x 1500 mm Weight: approx. 4.5 t The seller is not liable for typographical or data transmission errors. The machine's visual appearance, technical condition, and wear conform to its age; used machines are sold without any warranty.

Condition: new, functionality: fully functional, Year of construction: 2026, control type: CNC control, degree of automation: automatic, actuation type: electric, controller manufacturer: Siemens, roller (bottom) diameter: 160 mm, roller (top) diameter: 175 mm, side roll diameter: 135 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness (max.): 7 mm, power: 4.4 kW (5.98 HP), input voltage: 400 V, input frequency: 50 Hz, warranty duration: 12 months, Equipment: centralized greasing system, cone bending device, documentation/manual, hardened rollers, swiveling upper roller, Electronically Controlled, Electrohydraulic Four-Roller Plate Bending Machine Manufacturer: FACCIN, Model 4 EDL 1617 Technical Specifications: Number of rollers: Four Geometry of side rollers: Linear guides Working width: 1500 mm Top roller diameter: 175 mm Bottom roller diameter: 160 mm Side roller diameter: 135 mm Pressing force against top roller: 80 tons Guaranteed installed power: 4.4 kW (6 HP) Guaranteed maximum rotation speed: 0–10 m/min Guaranteed machine weight: 3,150 kg Length: 3,300 mm Width: 1,170 mm Height: 1,100 mm Guaranteed Performance: For material with yield strength 260 N/mm² Rolling capacity (full working width): 7 mm Pre-bending capacity (full working width): 6 mm From pipe diameter: 875 mm Rolling capacity (full working width): 5 mm Pre-bending capacity (full working width): 5 mm From pipe diameter: 225 mm Standard Equipment: Double linear guide system for roller movement Extremely wide bearing blocks MCS double bearing system for roller rotation Extra heavy-duty, double-support swing bearing Electronic Parallelism System EPS Hardened rollers for high wear resistance All rollers ground after heat treatment Siemens PLC control system Electric drive for top roller for increased efficiency Safety trip wire with emergency stop and CE certification Centralized lubrication Cone bending device Bjdpswwt Ddefx Ab Ujda Optional Equipment Included: CNC control PGS-ABSOLUTE

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN 4HEP S54 Bodpjiivgrefx Ab Ueda Four roll bending machine Electronically controlled, electric drive, four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rolls: planetary guide Working length: 3000 mm Top roll diameter: 300 mm lower roll diameter: 280 mm Side rolls diameter: 200 mm Guaranteed installed power: 10.8 kW Guaranteed maximum rolling speed: 5 m/min Guaranteed machine weight: 10,000 kg Length: 5,500mm Width: 1,400mm Height: 1,600mm Guaranteed services: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 18 mm Bending performance (full working width) 12 mm from pipe diameter 1500 mm Rolling capacity (full working width) 12 mm Bending capacity (full working width) 10 mm from pipe diameter 450 mm Standard equipment: Electrical drive of the top roll Planetary movement of the side rolls Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rollers for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, HAV 3293 Plate width: 3200mm Bdodpoiivg Ssfx Ab Usa Top Roll diameter: 930mm Side rolls diameter: mm 800 Machine weight: 150 Ton Rolling capacities (Y:260Mpa/Ø 4650mm): 3200mmx155mm Prebending capacities (Y:260Mpa/Ø 4650mm): 3200mmx115mm

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN 4HEP 3135 Four roll bending machine Electronically controlled, hydraulic four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rolls: planetary guide Working length: 3000 mm Top roll diameter: 350 mm Lower roll diameter: 330 mm Side rolls diameter: 250 mm Guaranteed installed power: 14.4 kW Bodpfjiivc Dex Ab Usda Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 13,000 kg Length: 5,700mm Width: 1,800mm Height: 2,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 20 mm Bending performance (full working width) 15 mm from pipe diameter 1750 mm Rolling capacity (full working width) 14mm Bending capacity (full working width) 12mm from pipe diameter 455 mm Standard equipment: planetary movement of the side rollers Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN 4HEP 3163 Four roll bending machine Electronically controlled, hydraulic four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rollers: planetary guide Working length: 3000 mm Top roll diameter: 630 mm Lower roll diameter: 570 mm Side rolls diameter: 500 mm Guaranteed installed power: 72 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 58,000 kg Length: 6,800mm Width: 3,600mm Height: 3,550mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 70 mm Bending performance (full working width) 60 mm from pipe diameter 3150 mm Rolling capacity (full working width) 55 mm Bending capacity (full working width) 50 mm from pipe diameter 820 mm Standard equipment: Bdjdpfsiivfqox Ab Uja Planetary movement of the side rolls Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN HAV 3162 variable three-rolls bending machine Electronically controlled, hydraulic three-rolls bending machine Bdsdpfoiivgysx Ab Uoa Technical specifications: Number of Rolls: Three Geometry of the side rolls: variable Working length: 3050 mm Top roll diameter: 620 mm Side rolls diameter: 550 mm Pressure force against the top roll: 630 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 55 kW (75 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 45,000 kg Length: 7,600mm Width: 3,700mm Height: 3,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 75 mm Bending performance (full working width) 48 mm from a pipe diameter of 3,100 mm Rolling capacity (full working width) 55 mm Bending performance (full working width) 40 mm from pipe diameter 805 mm Standard equipment: variable geometry with linear guides for rolls movement Extra long release arm for increased frame stability Electronic parallelism system EPS Hardened rolls for high wear protection All rolls ground after heat treatment Siemens S7-HMI PLC control PGS-CLASSIC control with Siemens touch panel Hitech hydraulic and electric package Simultaneous rotation and rolls movement Safety trip wire with emergency stop and CE certification central lubrication Water cooling for the hydraulics cone bending device Prepared for retrofitting supports and roller conveyors FACCIN Advantage Package AP

Condition: new, functionality: fully functional, Year of construction: 2026, BIKO B4 2014 Linear Four roll bending machine Hydraulically controlled four-rolls bending machine Make BIKO, model B4 2014 Technical specifications: Number of Rolls: Four Geometry of the side rollers: linear guides Working width: 2000 mm Top roller diameter: 145 mm Lower roller diameter: 130 mm Side roller diameter: 130 mm Guaranteed installed power: 5.5 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 2,300 kg Length: 2,900mm Width: 900mm Height: 1,000mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 4 mm Bending performance (full working width) 3 mm from pipe diameter 725 mm Rolling capacity (full working width) 3 mm Bending performance (full working width) 2 mm from pipe diameter 190 mm Standard equipment: Linear guide system for rolls movement Extremely wide bearing blocks Needle bearing for the rolls rotation Extra heavy double hinged folding release Hardened rolls for high wear protection Bedpeiinknsfx Ab Uoda Hydraulic parallelism system of the side rolls Digital display for the position of the side rolls and the bottom roll cone bending device Control on the swiveling control panel Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, TECHNICAL SPECIFICATIONS: Number of rolls FOUR Geometry linear guides Maximum plate width mm 3000 Top roll diameter mm 390 Bottom roll diameter mm 370 Side rolls diameter mm 295 Installed power HP 40 Stepless variable rotation movement m/1' 4-8 Machine weight (guaranteed) Kg 19,000 Guaranteed performance with material yield point 260 N/mm² Rolling capacity (full working width) Ø 1950 mm 25 mm Bending performance (full working width) Ø 1950 mm 20 mm Rolling capacity (full working width) Ø 507 mm 18 mm Bending performance (full working width) Ø 507 mm 16 mm Bdjdpfxogd T R Do Ab Uea • Hardened and polished rollers • Siemens NC control • Cone bending device with electronic tilting

Condition: new, functionality: fully functional, Year of construction: 2026, 4 HEL 3128 Four rolls bending machine Electronically controlled, hydraulic four-rolls bending machine Make FACCIN, model 4 HEL 3128 Technical specifications: Number of Rolls: Four Geometry of the side rolls: linear guides Working width: 3050 mm Top roll diameter: 285 mm Lower roll diameter: 275 mm Side rolls diameter: 205 mm Certified rolls hardness: 950-1050 N/mm² Pressure force against the top roll: 150 tons Working pressure at maximum power: 190 bar Guaranteed installed power: 11 kW (15 hp) Guaranteed maximum rotation speed: 4-8 m/min Guaranteed machine weight: 9,000 kg Length: 5,450mm Width: 1,520mm Height: 1,450mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 12 mm Bending capacity (full working width) 8 mm from a pipe diameter of 1,425 mm Rolling capacity (full working width) 8 mm Bending performance (full working width) 6.5 mm from pipe diameter 370 mm Standard equipment: Double linear guide system for rolls movement Extremely wide bearing blocks MCS double bearing system for the rolls rotation Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection All rolls ground after heat treatment Siemens S7 PLC control Bdedpfx Asiink Sjb Uoa Hitech hydraulic and electric package Safety trip wire with emergency stop and CE certification central lubrication cone bending device FACCIN AP package CNC control PGS-ULTRA

Condition: new, functionality: fully functional, Year of construction: 2026, max rolling capacity (cold): mm. 32 max prebending capacity (cold): mm. 24 at diameter mm. 2050 with material yield strength N/mm2 260 working length: mm. 3050 number of rolls: four top roll diameter mm. 410 Bsdpfx Abof T Rzfe Usda pinching roll diameter mm. 390 driven rolls : two rotation speed 5 m./min. rolls rotation: hydraulic installed power: 30 PS Voltage 400V, 50Hz, 3Ph Inkl.: - hardened & polished rolls - cone bending device - electronic rolls parallelism - Siemens PLC Control - CE certificate - control console on wheels

Condition: new, functionality: fully functional, Year of construction: 2026, roller diameter: 200 mm, roller length: 2,000 mm, working width: 2,000 mm, sheet thickness steel (max.): 8 mm, type of input current: three-phase, working length: 2,000 mm, Hydraulically controlled four-rolls bending machine Make BIKO, model B4 2020 Technical specifications: Number of Rolls: Four Geometry of the side rolls: linear guides Working width: 2000 mm Top roll diameter: 200 mm Lower roll diameter: 180 mm Side rolls diameter: 160 mm Guaranteed installed power: 5.4 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 3,950 kg Length: 3,200mm Width: 1,000mm Height: 1,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 8 mm Bending performance (full working width) 6 mm from pipe diameter 1000 mm Rolling capacity (full working width) 5 mm Bending capacity (full working width) 4 mm from pipe diameter 265 mm Standard equipment: Linear guide system for roller movement Extremely wide bearing blocks Needle bearing for the roller rotation Extra heavy double hinged folding release Hardened rolls for high wear protection Hydraulic parallelism system of the side rollers Digital display for the position of the side rolls and the bottom roll Bedpfxsd Iclrj Ab Ujda cone bending device Control on the swiveling control panel Safety lanyard with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, Electronically controlled, hydraulic four-roller bending machine Make FACCIN, model 4 HEL/S 2122 Technical specifications: Number of Reels: Four Geometry of the side rollers: linear guides Working width: 2000 mm Top roller diameter: 225 mm Lower roller diameter: 215 mm Side roller diameter: 165 mm Pressure force against the top roller: 100 tons Guaranteed installed power: 9.2 kW (12.5 hp) Guaranteed maximum turning speed: 4-8 m/min Guaranteed machine weight: 4,450 kg Length: 3,500mm Width: 1,200mm Height: 1,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 11 mm Bending capacity (full working width) 8 mm from a pipe diameter of 1,100 mm Rolling capacity (full working width) 8 mm Bending performance (full working width) 6 mm from pipe diameter 286 mm Bodpfx Aed Eqg Heb Uoda Standard equipment: Double linear guide system for roller movement Extremely wide bearing blocks MCS double bearing system for the roller rotation Extra heavy double hinged folding bearing Electronic parallelism system EPS Hardened rollers for high wear protection All rolls ground after heat treatment Siemens S7 PLC control Hitech hydraulic and electric package Safety trip wire with emergency stop and CE certification central lubrication cone bending device Optional equipment included: CNC control PGS-ABSOLUTE

Condition: new, functionality: fully functional, Year of construction: 2026, Hydraulic two-roller bending machine Guaranteed capacities: Sheet thickness Bending with material 260 N/mm² Yield point: 2 mm Sheet thickness bending with material AISI 304-316 stainless steel: 1.5 mm Cycle time per part: 15 seconds Technical specifications: Working length: 1000 mm Bdedpfx Absc S N Ris Uoa Installed power: 5.5 kW Rolling speed: 7 m/min immediately available from the factory!

Condition: new, functionality: fully functional, Year of construction: 2026, Three rolls variable axis bending roll Make FACCIN, model HAV/S 3145 Technical specifications: Number of Reels: Three Geometry of the side rollers: variable Bdodpfxsc S N Nqe Ab Uja Working width: 3000 mm Top roller diameter: 450 mm variable three-roller bending machine

Condition: new, functionality: fully functional, Year of construction: 2026, Hydraulically controlled three-roller bending machine Make BIKO, model B3 2021 Technical specifications: Number of Reels: Three Geometry of the side rollers: linear guides Working width: 2000 mm Top roller diameter: 215 mm Side roller diameter: 195 mm Guaranteed installed power: 7.2 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 3,000 kg Bodscuxp Topfx Ab Uoda Length: 3,700 mm Width: 1,000mm Height: 1,100 mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 13 mm Bending capacity (full working width) 9 mm from pipe diameter 1075 mm Rolling capacity (full working width) 9 mm Bending performance (full working width) 7 mm from pipe diameter 280 mm Standard equipment: Double linear guide system for the roller movement Extremely wide bearing blocks MCS double bearing system for the roller rotation Extra heavy double hinged release Hardened rolls for high wear protection Hydraulic parallelism system of the side rolls Digital display for the position of the side rolls cone bending device Safety trip wire with emergency stop and CE certification Mobile control panel