Used Force for sale (5,896)

Condition: used, Line consisting of: (1) Twin-screw extruder Kjdpjx I Emfofx Ab Tsdh Technical details: Screw diameter 75 mm, capacity: max. 200 kg/h, KraussMaffei-Berstorff control system, weight 3.5 t /// Drive: SIEMENS 2860 / 30.5 rpm, 5,070 Nm, weight 1.2 t (1) Calibration table Technical details: With three (3) SPECK pump systems, table length approx. 4 m (1) Haul-off unit Technical details: Speed 0.1–11 m/min, pulling force 25,000 N, contact length 1,500 mm, profile clearance WxH 300 x 180 mm (1) Punching device + guillotine unit Technical details: Punching force 1,800 N, design: C-frame, punching frequency 130 strokes/min, punching tool LxWxH 185x180x132 (1) Tilting table Technical details: For pushing a single-strand roller shutter into an adjacent profile, table length approx. 6,000 mm

Condition: used, Electro Dual Screwdriving Unit with Automatic Feed and Pneumatic Double Stroke BÖLLHOFF Type UVS-100-2-R-E The Böllhoff Uniquick Vario UVS-100-2-R-E dual screwdriving unit is equipped with a pneumatic double stroke, operated via Festo valves and cylinders. Additionally, various monitoring systems are installed for full automation. Technical data: Torque of electric screwdriver: 0.6 Nm Gearbox torque: max. 10 Nm Speed: max. 20,000 rpm Rated voltage: 3~ 0-230 VAC Current consumption: max. 7 A (per screwdriver) Pneumatic long-stroke cylinder: 80 mm Pneumatic short-stroke cylinder: 20 mm Total pneumatic stroke: 100 mm Spring stroke for screwdriver: 20 mm Distance between both screwdriving tools: 73 mm - Equipped with a TORX bit T27 or TP27 (presumably for M6 screws) - Requires Bosch Rexroth LT303 power module for operation (power module not included) Screwdrivers 1 and 2 are each composed of the following components: Rexroth type servo motor Rexroth type 0 planetary gearbox Rexroth type 0 encoder Rexroth type 0 straight drive output Component details: Electric screwdriver unit Rexroth Servo motor Rexroth Type: EC302 SZ3 Material number: 0 Torque: 0.6 Nm Peak torque: 0.7 Nm Speed: max. 20,000 rpm Current consumption: max. 7 A Rated voltage: 3~ 0-230 VAC Weight: 0.8 kg Gearbox unit Rexroth Type: 3GE27 SZ3 Material no.: 0 Efficiency: 90% Gear ratio: i=18.9 Torque: max. 10 Nm Weight: 0.4 kg Installation length: 65.5 mm Encoder Rexroth Type: 2DMC012 SZ2 Material no.: 0 Nominal torque: 12 Nm Reduction ratio: 1 Efficiency: 1 Weight: 0.55 kg Installation length: 118.5 mm Straight drive output Rexroth Type: 2GA82 SZ2 1/4" SQ Material no.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Max. torque: 10 Nm Reduction ratio: 1 Weight: 0.2 kg Installation length: 90 mm Kdodpfxohxvu Eo Ab Teh One 7 m motor connection cable is included in the delivery. Overall dimensions W x H x D: approx. 180 x 920 x 300 mm Total weight: approx. 20 kg Good condition

Condition: used, Electric dual screwdriver unit with automatic feed and pneumatic double stroke, mounted on handling device, handling system, manipulator for screwdriving technology. Screwdriving Unit: BÖLLHOFF / BOSCH REXROTH Type UVS-100-2-R-E The Böllhoff Uniquick Vario UVS-100-2-R-E dual screwdriver unit features a pneumatic double stroke via Festo valves and cylinders. Various monitoring systems are installed to enable full automation. Screwdriver 1 consists of the following components: - Rexroth type servomotor - Rexroth type 0 planetary gearbox - Rexroth type 0 encoder - Rexroth type 0 straight drive head Screwdriver 2 consists of the following components: - Rexroth type servomotor - Rexroth type 0 planetary gearbox - Rexroth type 0 encoder - Rexroth type 0 offset drive head Dimensions (WxHxD): 165 x 1000 x 200 mm Pneumatic long stroke: 30 mm Pneumatic short stroke: 20 mm Screwdriver spring travel: 20 mm Last screws used: M6 x 15 mm Electric screwdriver unit Rexroth Servomotor Rexroth Type: EC302 SZ3 Material number: 0 Torque: 0.6 Nm/A Peak torque: 0.7 Nm Speed: max. 20,000 rpm Current draw: max. 7 A Weight: 0.8 kg Gearbox unit Rexroth Type: 3GE27 SZ3 Material No.: 0 Efficiency: 90% Reduction ratio: i=18.9 Max. torque: 10 Nm Weight: 0.4 kg Installation length: 65.5 mm Encoder Rexroth Type: 2DMC012 SZ2 Material No.: 0 Nominal torque: 12 Nm Reduction: 1 Efficiency: 1 Weight: 0.55 kg Installation length: 118.5 mm Straight drive head Rexroth Type: 2GA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Max. torque: 10 Nm Reduction: 1 Weight: 0.2 kg Installation length: 90 mm Offset drive head Rexroth Type: 2VNA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Max. torque: 10 Nm Reduction: 1 Weight: 0.6 kg Installation length: 153 mm Handling system: JÄGER HANDLING Type: Handy-flex 300 Horizontal movement: 400 mm Vertical movement: 450 mm Load capacity: max. 14 kg Handyflex reach: 250 to 650 mm Handyflex reach (swung out): max. 860 mm Swivel radius at full extension: max. 360° Guide column vertical: Ø 30 mm Guide columns horizontal: Ø 20 mm - Balancer for vertical movement - Adjustable load capacity - Adjustable stop for limiting swivel radius Dimensions (L x W x H): approx. 1150 x 650 x 1400 mm Total weight: approx. 90 kg Good condition Without the blue steel pallet as base plate Kjdsfx Hyfopfx Ab Tjdh Blue steel base plate is not included in the scope of delivery.

Condition: used, Single-column eccentric press RICHTER type PEKRS 80 Year of construction 1970 - overhaul 2024 Compressive force 80 ton. throat depth 350 mm Table size 900 x 650 mm Hole in the clamping table Ø 200 mm ram surface 700 x 500 mm Stroke rate 70 strokes/min. Stroke adjustment 6 - 100 mm ram adjustment 85 mm Installation height max. 400 Clamping pin bore Ø 50 mm Table height above floor 810 mm Motor power 8 kW Mains connection 400 Volt, 50 Hz - ORTLINGHAUS pneumatic clutch/brake combination - HERION XSz 32 press safety valve - Pneumatic ram compensation cylinder - Overload protection with breaker plate in ram - Central grease lubrication with hand pump Space requirement L x W x H 1800 x 1250 x 2830 mm Weight 5.7 tons Very good condition Technically overhauled and converted to the latest UVV with new electrics Control conversion in 05/2024 - suitable for manual insertion work - in accordance with DGUV Information 209-030 Press inspection and Machinery Directive 2006/42/EC Low Voltage Directive 2014/35/EU EN ISO 16092-1: Safety of machine tools - Presses - Part 1: General safety requirements EN ISO 16092-2: Machine tools - Safety of presses - Part 2: Mechanical presses - Control system with plain text error messages and diagnostic screen for rapid fault localization - New electrical cabinet, mounted on the side of the machine - completely based on SIEMENS, with PLC S7-1200 PROFIsafe and 7" TFT touch display - Two-hand control panel with emergency stop and engagement lock - el. foot switch - Cam switch unit with run monitor control - Stroke release via HERION XSz 32 press safety valve with pneumatic pressure compensator - New wiring of the machine - Updated operating instructions The machine is equipped with 6 operating modes: 1 = Set-up 2 = Single stroke two-handed Kdsdpfx Absi Db Ibj Tsh 3 = Single stroke foot 4 = continuous run foot 5 = automatic continuous run 6 = reverse run

Condition: used, Double-column hydraulic press NEFF Type RHS 125 Z Hydraulic drawing press Machine No. 3973 Year of manufacture 1983 Pressing force: 125 tons Column gap: 1050 mm Lateral column clearance: 550 mm Table size: 1000 x 800 mm Ram size: 1000 x 800 mm Kdjdpfxjguvtle Ab Tsh Ram stroke: 350 mm Installation height max.: 750 mm Table height above floor: 960 mm Blankholder force: approx. 12 tons at 105 bar Blankholder stroke: 100 mm Through-hole in table: Ø 202 mm Rapid advance speed downwards: approx. 360 mm/sec Rapid advance speed upwards: approx. 360 mm/sec Working speed: approx. 36 mm/sec Oil tank capacity: approx. 1000 liters Main pump motor power: 22 kW Control pump motor power: 4 kW Control pump motor power: 2.2 kW Electrical connection: 400 Volt, 50 Hz - Hydraulic blankholder cushion underneath the table with a through-bore in the table top Ø 202 mm - Precise 4-column guide on the ram corners - Infinitely variable pressing force adjustment - Electrically adjustable fixed stop via hydraulic motor - Cutting shock damping - Two-hand control panel for stroke release on the press - Free-standing control cabinet (1600 x 500 mm) - Documentation such as operating instructions, electrical wiring diagram, and PLC program printout available Required space L x W x H: 2600 x 2400 x 4270 mm Weight: approx. 14 tons Good condition

Condition: used, Machine not operational – control system not running Special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Serial No. 300487 Year of manufacture: 2006 Pressing force: 500 tons Column gap front and rear: 2520 mm Table surface: 2500 x 2500 mm Ram surface: 2500 x 2500 mm Ram stroke: 600 mm Installation height max.: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable approach speed: 100-800 mm/s Pressurization to 5000 kN: approx. 0.7 sec. Return speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-position flat guide for the ram - Hydraulic ram locking at TDC - Freestanding control cabinet (200 x 50 cm) - Siemens PLC control S7-314 - Operation via Siemens OP 170-B (5.7”) - Two-hand control desk, freestanding - Floor-level installation Kdjdpfxedzqptj Ab Teh - Table plate 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication - Operating manual with circuit diagrams Required space (L x W x H): 372 x 260 x 460 cm Required space for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: used, Frame die-cutter - Swivel frame die-cutter - Flatbed die-cutter - Platen die-cutter - Eccentric press Punch + feed for the use of bandknife punching tools Flatbed die cutter HELMERDING type PSH 25 Com. No. EP 97784 Machine. No. 6073 Year of construction 1998 Compressive force 25 ton. Clearance between the tie rods 700 mm Table surface = installation space 800 x 670 mm Table surface = installation frame width 510 x depth 440 mm, plate thickness 20 mm Plunger surface 800 x 670 mm Hole in the table 490 x 420 mm Plunger stroke 45 mm Ram adjustment travel 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min. Motor power 15 kW Mains connection 400 Volt, 50 Hz - Controlled drive for infinitely variable stroke rate - Pneumatic clutch-brake combination - ram compensation cylinder - VOGEL automatic central lubrication system - solid base plate with 4 swinging elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Ksdpfxsdzqmzs Ab Tedh Weight 4.5 tons good condition The machine was formerly used for cutting out cardboard blanks. Ideal for cutting out non-woven fabrics or similar for breathing masks.

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm Kjdpjdzqltsfx Ab Tsdh - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Kdsdpfew A Amrex Ab Tsh Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: used, Inverter Welding Machine for Manual Metal Arc Welding TECHNOLIT PROFImat 170 Plus Type MMA Welding Machine, Inverter Welding Machine, Manual Electrode Welding Inverter New – unused Serial No.: TB1703500316 Article No.: 440030 Year of Manufacture: 2022 TIG (DC) Output: 170 Amp. 45% duty cycle 150 Amp. 60% duty cycle 135 Amp. 100% duty cycle MMA Output: 170 Amp. 35% duty cycle 145 Amp. 60% duty cycle 125 Amp. 100% duty cycle Adjustment Range: 5–170 Amp. infinitely variable Power Supply: 230 Volt, 50 Hz - Hot start function (optimizes ignition characteristics, making it easier to start welding with difficult-to-ignite electrodes) - Anti-stick function (optimizes electrode control and prevents the electrode from sticking) - Arc-force function (optimizes arc stability and improves penetration) - Lift-arc arc ignition - Suitable for stick electrode welding, for all electrode types up to Ø 4 mm Kdedpfx Aoi E Iz Ijb Tsh - Ground cable with plug connection - Electrode holder with 3-meter cable and plug connection - Equipped with 230-volt Schuko plug - S-mark for welding under increased electrical hazard conditions - Overvoltage protection Dimensions (machine without cables) L x W x H: 310 x 155 x 265 mm Weight (without cables): 7 kg NEW – unused, from stock

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition Kedpfewbvmiex Ab Tsdh

Condition: used, 5-fold combined profile steel shears PEDDINGHAUS type 210 AD/13 Machine. No. 529A059 Year of manufacture approx. 1970 Punching machine: Punching force 60 ton. Punch stroke 25.5 mm Punching capacity Ø 25 mm in 16 mm sheet metal Kdsdpfx Aei Duh Iob Tsh Ø 20 mm in 19 mm sheet metal throat depth 365 mm Bar steel shears: Cutting capacity Round 42 mm Square 38 x 38 mm Flat steel shears: Cutting capacity with shearing angle 5° 150 x 13 mm or 200 x 10 mm Blade length 245 mm Profile steel shears: Shearing capacity angle steel at 90° 110 x 10 mm Shearing capacity angle steel at 45° 90 x 9 mm T-steel 110 x 10 mm Notching device: Rectangular notcher up to 12 mm sheet metal Punch dimensions 85 x 50 mm Motor power 3 kW Mains connection 380 Volt, 50 Hz. - Center punch detection device via hand lever and centering device - Mechanical stroke release via hand lever - Flat steel shears equipped with 2° blade - Mechanical hold-down device on the profile steel shears, bar steel shears and flat steel shears Space requirement L x W x H 1500 x 800 x 1900 mm Weight 2000 kg good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Kdedpsi A A Tbofx Ab Tjh Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: used, Pneumatic press, compressed air press BOSCH type Manufacturer no.: Year of manufacture: 1980 Pressing force: 18 kN = 1.8 t at 5 bar 15 kN = 1.5 t at 4 bar 12 kN = 1.2 t at 3 bar 8 kN = 0.8 t at 2 bar 6 kN = 0.6 t at 1.8 bar Throat depth: 100 mm Ram stroke: 70 mm Table size: 245 x 200 mm Ram face: Ø 45 mm Max. installation height: 235 mm Clamping pin bore: Ø 20 mm with clamping screw Compressed air requirement: 5 bar - Pressing force infinitely adjustable via pressure regulator - Pneumatic cylinder with ram adjustable in height by 90 mm - Pneumatic dual-hand control - Mounted on a metal frame with wooden boards Required floor space (L x W x H): 1050 x 700 x 1600 mm Weight of pneumatic press: 82 kg Weight including table frame: 140 kg Kedpfx Ash U Dtujb Tedh In very good condition

Condition: used, Inverter welding machine for manual electric welding IMS - GYS type PROGYS FLEX 280A CEL MMA welding machine, inverter welding machine, manual electric welding inverter Serial no. IEC 60974 Year of manufacture 2020 Power with mains operation 400 Volt (40% ED) 280 Amp. Power with mains operation 400 Volt (60% ED) 200 Amp. Power for mains operation 400 Volt (100% ED) 170 Amp. Power for mains operation 230 Volt (40% ED) 200 Amp. Power for mains operation 230 Volt (60% ED) 180 Amp. Power for mains operation 230 Volt (100% ED) 150 Amp. Adjustment range 5-280 Amp. stepless Mains connection 230 / 400 Volt, 50 Hz. - Operating voltage from 110 to 480 volts alternating current - Adapts fully automatically to the existing mains supply - equipped with 16 Amp. CEE plug for 400 Volt mains voltage - Hot-start function (optimizes the ignition behaviour, simplifies the welding start of electrodes that are difficult to ignite) - Anti-stick function (optimizes electrode guidance and prevents the electrode from sticking) - Arc-Force function (optimizes arc stability and improves penetration) - Digital display - Plug socket for remote control connection Kdodpjvg Rh Tjfx Ab Tsh - Earth cable with plug connection - Electrode tongs with 3 meter cable and plug connection - Stick electrode welding, can be used for all electrode types up to Ø 5 mm - TIG-DC welding (without TIG hosepack) - The device may be connected to a flexible three-phase power supply between 110 V and 480 V or to a fixed three-phase 400 V power supply (50 - 60 Hz) plus ground wire. This appliance may only be connected to a 3-phase power supply system with 4 conductors, where the neutral conductor is earthed. Dimensions (appliance without cable) L x W x H 470 x 270 x 430 mm Weight (without cable) 23 kg New, unused

Condition: used, Spot and projection welding machine NIMAK type BMP 20/150 Spot welding machine, projection welding machine Mach. No. 81692 year of manufacture approx. 1980 Kodpfsv Dxm Sjx Ab Tedh Power at 50% duty cycle 150 kVA Clamping plate below 200 x 160 mm Clamping plate above 200 x 160 mm Power setting continuously variable Max. projection 150 mm Electrode force 200 - 2000 kp continuously variable Operating air pressure max. 6 bar Connection power 600 kVA Mains connection 380 volts, 50 Hz - Welding control DTW 4Z 2P - Single spots and series spots - Parallel electrode guidance - Water-cooled without cooling unit - Electric 2-hand control panel with emergency stop - Control cabinet with control permanently attached to the machine Space requirement L x W x H 1000 x 800 x 1800 mm Weight 900 kg good condition

Condition: used, Single column hydraulic press DUNKES type HZT 2,5 Machine No. H94-2558 Year of construction 1994 pressure force 2,5 ton. throat 180 mm table area 420 x 300 mm drop-through opening in table 60 x 185 mm ram surface Ø 40 mm clamping spigot bore Ø 20 mm ram stroke 160 mm Installation height max. 250 mm Rapid traverse downward 65 mm/sec. Rapid traverse upwards 160 mm/sec. Working speed 8,3 mm/sec. Table height above floor 950 mm Hydraulic operating pressure 135 bar Tank capacity hydraulics approx. 100 liters Drive power 1,5 kW Mains connection 400 Volt, 50 Hz - Installation height can be increased by shortening the piston rod by 80 mm - Pressure and travel cut-off - 2-hand operation at the machine - stroke counter - safe press control with 2 monitored hydraulic valves - UVV 11.064 VGB 7.n.5.2 (for manual insertion work) - 32047 read off operating hours Kjdpfxsh Uhqyj Ab Tedh - Electrical circuit diagram and hydraulic diagram available space requirement L x W x H 1100 x 980 x 1950 mm weight 700 kg very good condition

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 Kdodpfeik Srwsx Ab Tjh pressure force 5 ton. throat 125 mm head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm weight 530 kg very good condition

Condition: used, Spot projection welding machine NIMAK type PMP 5 / 35 Spot welding machine, projection welding machine Make No. 88100 Year of construction approx. 1988 power at 50% ED 35 kVA throat 250 - 450 mm working stroke 40 mm electrode force 100 - 460 kp infinitely variable Electrode force at 6 bar 460 daN Operating air pressure 2 to 6 bar Kjdpfx Ajhubgzsb Todh Electrode arm Ø 60 mm Electrode holder Ø 30 mm Insert electrodes cone MK 2 Ø 17.78 mm Arm distance 200 / 400 mm Adjustability of electrode holder 200 mm Connected load 83 KVA Mains connection 380 Volt, 50 Hz - 4-time control - stepless power adjustment - single points and series points - bouncing electrode guide - water cooled (without cooling unit) - electrical foot switch space requirement L x W x H 1200 x 650 x 1500 mm weight 300 kg good condition

Condition: used, Single-column hydraulic press HYDRAP type HPSK 25 No. 6312 Year of construction 1989 Kdsdpfx Abohrakvs Tjh Pressure force 25 ton. Ram stroke 500 mm throat depth 300 mm Installation height 700 mm Table surface 1000 x 500 mm Table bore Ø 210 mm Plunger surface 400 x 360 mm Clamping pin bore Ø 40 mm Table height above floor 855 mm Feed speed in rapid traverse 280 mm/sec. Pressing speed 3.5 mm/sec. to 25 mm/sec. Return speed 280 mm/sec. Hydraulic tank capacity 240 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz. - Operation and programming via SIEMENS S5 with OP1 control system - Measuring system for stroke adjustment - Pressing speed infinitely variable via potentiometer - Pressure setting infinitely adjustable manually via pressure regulator - Short stroke device - Mechanical tool clamping on ram with T-slots and clamping pin hole - Switch cabinet with electrical control on the machine - Two-hand operation and electrical connection for foot control - Control provided for electrical mold monitoring - Hydraulic diagram and electrical diagram available Space requirement L x W x H 1800 x 1200 x 2930 mm Weight approx. 4 tons good condition

Condition: used, AC Spot Welding Machine, Projection Welding Machine ARO Type MA 350 DC AC Resistance Welding Machine Mach. No. MA35031332 / 9731122B110 Year of Manufacture 1997 Power at 50% duty cycle: 30 kVA Power at 100% duty cycle: 21 kVA Maximum welding power: 156 kVA Thrust 550 mm Electrode arm diameter: 60 mm Electrode holder diameter: 25 mm Cylinder stroke max. 80 mm Electrode force max. 730 daN (at 6 bar), continuously adjustable Operating air pressure 0.5 to 6 bar Mains connection 400 volts, 50 Hz Connected load 75 kVA / 63 amps / Cable cross-section 3x 16 mm² Maximum possible sheet pairing: 5 mm + 5 mm - ARO Micro welding control system 2X16 III Version 6Z2P Type 1B (6 times - 2 programs) - Continuous welding current adjustment via thyristor module - Parallel electrode guide - Double-stroke welding cylinder (pre-stroke / welding stroke) - Single-stroke and continuous spot welding modes - Electrode force continuously adjustable via air pressure - Water-cooled by external water cooling (water cooling unit not included) - Electric foot switch - Control cabinet with control system permanently mounted on the machine - PC interface RS 485 Kdsdpfx Aohpf Iysb Teh - Spot weld counter - Operating instructions for control system, spot welder, and electrical diagram included Space requirement: W x H x D 520 x 1550 x 1150 mm Weight: 290 kg Very good condition

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Kdjdpfx Asuz If Nsb Tsh Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine Manufacturer PEE-WEE Type P 24 Q serial no. LC2403099 year of construction 2004 Rolling force max. 24 ton. Tool diameter max. 200 mm Rolling spindle diameter 69,85 mm Tool bore diameter 70 mm (nominal diameter) Tool length, tool length max. 180 mm Workpiece diameter max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 rpm Motor power hydraulics approx. 3 kW Ksdjh A S Htjpfx Ab Todh Motor power roller drive 5.5 kW Mains connection 400 Volt, 50 Hz - Swivel roller spindle for threaded continuous rollers - Rolling spindle speed in 4 stages via gear changeover - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons good condition Grooving rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The thread length is maximum as long as the rolling tools are wide. Continuous rolling: When the thread length is greater than the rolling tool width. Through-feed tools have 3 sections - the infeed, the calibration section and the outfeed. Grooved rollers have no pitch and are swiveled with the pitch angle of the profile to be rolled. Pitch rollers differ from grooved rollers in that they have a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Condition: used, Capacitor discharge welding machine MEGATRONIC type CD-1200 / QB 2 / 6P Capacitor discharge welding with high currents and minimum welding times. Spot projection welding machine The CD (Capacitator-Discharge) welding technology works on the principle of transformed capacitor discharge. Year of manufacture 1993 Very high welding power with relatively small power supply. Kjdpfxjguvtde Ab Tedh - very short welding times, welding process with current rise and high welding current in milliseconds - no distortion or annealing - no significant heating of the edge areas, ideal for heat sensitive components - welding of steels with high carbon content - welding of surface coated workpieces rated power 12288 Ws Uc 3200 Volt Capacity 2400 µF Open circuit voltage 10 volts Electrode force 200-2000 daN infinitely variable Operating air pressure 6 bar Mains fuse min. 35 Amp. Operating current 32 Amp. Mains connection 400 Volt, 50 Hz - Programmable control megapuls CD-12000 - pralleler electrode guide - Electrical 2-hand control panel adjacent - Switch cabinet with control fixed to the machine weight 3000 kg good condition

Condition: used, Capacitor discharge welding machine MEGATRONIC type CD-1200 / QB 2 / 6P Capacitor discharge welding with high currents and minimum welding times. Spot projection welding machine The CD (Capacitator-Discharge) welding technology works on the principle of transformed capacitor discharge. Masch. No. 352 / 92 Year of construction 1993 Very high welding power with relatively small power supply. - very short welding times, welding process with current rise and high welding current in milliseconds - no distortion or annealing - no significant heating of the edge areas, ideal for heat sensitive components - welding of steels with high carbon content - welding of surface coated workpieces rated power 12288 Ws Uc 3200 Volt Capacity 2400 µF Kdodpfx Abjguvtas Tjh Open circuit voltage 10 volts Electrode force 200-2000 daN infinitely variable Operating air pressure 6 bar Mains fuse min. 35 Amp. Operating current 32 Amp. Mains connection 400 Volt, 50 Hz - Programmable control megapuls CD-12000 - pralleler electrode guide - Electrical 2-hand control panel adjacent - Switch cabinet with control fixed to the machine weight 3000 kg good condition