Used Ham Mold for sale (2,940)

Condition: excellent (used), GWK TECO CS 90 E mold temperature controller, water, 95ºC, heating power 6 kW, cooling power 23 kW Features: - Display of functions and errors. - Access to device control at various password-protected levels. - Comparator (monitoring of momentary value parameter tolerance values ​​with alarm signaling). - Electronic medium level control with dry-run protection. - Automatic filling and refilling with medium level monitoring. - Additional option for manual filling with treated water. - Automatic air venting. - Leaky mold management function. - Mold emptying. Control / Security: - Temperature sensor in the power supply circuit. Chodpfx Aeznl Dusknjc - Overheating protection. - Contactless heating control with solid-state relays. - Safe temperature reduction upon shutdown. - Acoustic alarm signal (horn). - Symmetrical network load with three-phase drive and three-phase heaters. - 3-fold safety heating exclusion

Condition: not inspected (used), Year of construction: 1997, operating hours: 145,298 h, functionality: unexamined, machine/vehicle number: 31378, total length: 6,500 mm, total width: 2,000 mm, total height: 2,200 mm, A used machine from a site closure is being sold. Sale is made excluding any warranty for defects. Chodpfx Akezqabmjnec The machine has not been inspected but was in working order until the end. Weight approximately 9000 kg.

Condition: excellent (used), Year of construction: 2021, operating hours: 14,600 h, functionality: fully functional, machine/vehicle number: 248760, clamping force: 40,000 kN, screw diameter: 70 mm, displacement volume: 1,212 cm³, injection pressure: 1,650 bar, injection weight: 1,030 g, mold height (min.): 450 mm, ejector force: 964,000 N, ejector stroke: 250 mm, opening stroke: 1,000 mm, plate length: 1,450 mm, plate width: 1,200 mm, plate height: 1,100 mm, installation height: 3,650 mm, total length: 7,740 mm, total width: 2,340 mm, total height: 2,300 mm, overall weight: 25,600 kg, heating capacity: 29 kW (39.43 HP), pressure: 200 bar, number of injections: 1, pump power: 56,000 W, power: 118 kW (160.44 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 213 A, Equipment: documentation/manual, The machine has few operating hours and is in very good condition, having been well-maintained. The machine comes with a Viper12 robot, which was originally supplied with it and can be seen in the accompanying photos. The robot’s control system is not integrated with the machine, so the robot can be removed and used separately, or another robot can be installed in its place. The machine has three air valves and two hydraulic valves, Euro map signals, and a signal for the dispensing unit’s rotation speed. The machine also has a strip guard, which is not included but can be arranged separately. The extruder’s heating elements are insulated with thermal insulation. Due to the guard, the machine can operate with the rear door open. It also has a water tank with 8 zones and two additional blocks with 8 outlets each. The machine has 8 zones for heating the tooling. Only PS material has been injection molded on this machine. Chsdszqbk Nspfx Aknsc

Condition: like new (used), Year of construction: 2023, operating hours: 1,900 h, clamping force: 1,600 kN, screw diameter: 105 mm, clearance between the columns: 18,701,420 mm, displacement volume: 4,546 cm³, total length: 13 mm, total width: 4 mm, total height: 3 mm, overall weight: 83 kg, pressure: 1,778 bar, 8 hot runner channels 16 sequential pneumatic valves 2 air blowers SERVO PUMP PC MC6 WEIGHT 83T Chjdpfxsy I Apqo Aknoc DISTANCE BETWEEN PLATENS 3400MM

Condition: good (used), Year of construction: 1999, operating hours: 139,541 h, machine/vehicle number: 175489, clamping force: 500 kN, screw diameter: 25 mm, clearance between the columns: 320 mm, displacement volume: 97 cm³, injection weight: 97 g, ejector force: 30,000 N, overall weight: 2,250 kg, type of input current: DC, For sale is a reliable ARBURG Allrounder 320 S 500 - 150 (SELECTA Series) from 1999. The machine comes from a well-maintained industrial facility and is renowned for its durability and precision in plastics processing. Technical Data: Model: Allrounder 320 S 500 - 150 (Selecta) Machine No. / Serial No.: 175489 Year of manufacture: 1999 Operating hours (auto): 139,541 h Total connected load: 35.5 kW Total rated current: 66 A Electrical specifications Operating voltage: 400 V (3~ / 50 Hz) Control voltage: 230 V (~ / 50 Hz) DC control voltage: 24 V (DC) Rated current (motor/heating): 54.0 A / 12.0 A Machine dimensions & weight Length: approx. 3.40 m to 3.80 m (depending on injection unit version) Chsdey Dfqcepfx Aknec Width: approx. 1.43 m Height: approx. 2.00 m Total weight: approx. 2,250 kg Tie bar spacing (h x v): 320 mm x 320 mm Platen size (h x v): approx. 445 mm x 445 mm (up to 498 mm depending on configuration) Minimum mold installation height: 225 mm Opening stroke: 350 mm Max. daylight between platens: 575 mm Transport and loading can be organized Europe-wide, subject to an additional charge. All prices are subject to VAT. Inspection is possible by appointment. Please contact us – our team will be pleased to assist you. Trade-in or exchange possible! Machinery purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Are you looking for a high-quality yet cost-effective metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website.

Condition: used, Year of construction: 1994, functionality: fully functional, machine/vehicle number: 161729, clamping force: 1,000 kN, screw diameter: 40 mm, injection weight: 158 g, ejector force: 40,000 N, total length: 4,225 mm, total width: 1,370 mm, total height: 1,200 mm, overall weight: 3,080 kg, heating capacity: 5.5 kW (7.48 HP), pump power: 18,500 W, power: 24.3 kW (33.04 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 380 V, input current: 96 A, Equipment: documentation/manual, We are offering this used Arburg 370M 1000-250 injection moulding machine, year of manufacture 1994. Serial number: 161729 Codpeyrczgefx Aknohc Year: 1994 Operating voltage: 380 V 3~ 50 Hz Control voltage (230 V): 220 V ~ 50 Hz Control circuit voltage: 24 V = Total rated current: 96.00 A Total connected load: 55.0 kW Drive upgraded to xD card! If you have any questions or require further information, please feel free to send us a message or give us a call.

Condition: ready for operation (used), Year of construction: 2003, operating hours: 21,200 h, functionality: fully functional, machine/vehicle number: 190332, clamping force: 1,000 kN, injection weight: 15 g, ejector force: 66,000 N, ejector stroke: 225 mm, plate length: 795 mm, No reserve price – guaranteed sale to the highest bidder! Auction of a 3-color injection molding machine! TECHNICAL DETAILS Clamping force: 1,000 kN Tie bar spacing: 420 x 420 mm Mounting platens: 795 x 795 mm Mold height: 300 mm Maximum platen distance: 950 mm Ejector stroke: 225 mm Ejector force: 66 kN Injection Unit 1 (150 series) Screw diameter: 15 mm Injection volume: 17 cm³ Shot weight: 15 g Injection pressure: 2,750 bar Injection Unit 2 (150 series) Screw diameter: 15 mm Injection volume: 17 cm³ Chsdsy Hki Aspfx Aknoc Shot weight: 15 g Injection pressure: 2,750 bar Injection Unit 3 (60 series) Screw diameter: 15 mm (high abrasion resistant) Injection volume: 17 cm³ Shot weight: 15 g Injection pressure: 2,080 bar MACHINE DETAILS Control system: Selogica Clamping unit: hydraulic Operating hours: 21,200 h FEATURES 1 vertical injection unit, mounted on supports for the 2nd injection unit instead of on the clamping unit tie bars, manually operated, working position adjustable between 70 and 250 mm 2 x core pull Open nozzle 15 mm wear-resistant, without heating band (1st injection unit 150) Technology level 2 – servo-regulated hydraulic system with two variable displacement pumps Technology level 3 hydraulic system with three variable displacement pumps for simultaneous movements Heating band for open nozzle Injection unit 150 for vertical injection into the mold parting line for 2-component processing Position-regulated screw with control valve on the injection unit, including regulated back pressure Position-regulated screw with control valve for multi-component machines – for injection unit 2 Injection unit 60 for horizontal injection into the mold parting line as the 3rd injection unit For VE 906/00, injection unit 60 in L-position: unit lowered by 70 mm Plasticizing cylinder assembly 15 mm (without nozzle), with advanced feed and pressure reducing valve Open nozzle 15 mm wear-resistant, without heating band (L-position) Nozzle tip with radius 15 (L-position) Heating band for open nozzle (L-position) Position-regulated screw for the third injection unit Documentation/manual

Condition: excellent (used), Year of construction: 2012, Krauss Maffei Injection Moulding Machine KM 1300-12000 MX Control system: MC5 Year of manufacture: 2012 Clamping unit: Clamping force [kN]: 13,000 Platen dimensions (hxw) [mm]: 2210 x 1910 Clearance between tie bars (hxw) [mm]: 1570 x 1270 Min./max. mould height [mm]: 700–1400 Maximum opening stroke [mm]: 3050 Maximum ejector stroke [mm]: 350 Injection unit: Screw diameter [mm]: 105 Injection volume [cm³]: 5195 Shot weight in PS [g]: 4728 Injection pressure [bar]: 2296 Cjdpfx Aksy Hqwyjnshc Maximum injection speed [g/s PS]: 186 Electrical & hydraulic equipment: Rated pump motor power [kW]: 132 Rated screw motor power [kW]: 145 Heater power [kW]: 71 Dimensions and weight: Net weight with control cabinet [t]: 70 Dimensions (L x W x H) [m]: 13.03 x 3.65 x 2.82 Additional equipment: Parallel movements: Independent hydraulic screw drive Hot runners: 12 integrated temperature control zones Core pull: 3 hydraulic circuits (2 on moving platen, 1 on fixed platen) Pneumatics: 2 air blow-off valves + 1 valve for hot runner needle control Hydraulic accumulator Cooling: 20 rotameter system (10 for fixed platen + 10 for moving platen) Interfaces: Euromap 67 and Euromap 18 Insulation: BluePower – barrel thermal insulation

Condition: excellent (used), Year of construction: 2015, TEDERIC D250/1100 injection molding machine with SW6310S robot Manufacturer: TEDERIC Model: D250/1100 Year of manufacture: 2015 Serial number: D1025/0747 Robot: SW6310S Robot year of manufacture: 2019 Technical specifications Clamping force: 2,500 kN Screw diameter: 55 mm Centering diameter: injection side: 160 mm moving side: 100 mm Column spacing: 580 × 580 mm Chodeziiyvjpfx Aknoc Minimum mold height: 250 mm Maximum mold height: 600 mm Maximum platen spacing: 1,150 mm Maximum opening stroke: 550 mm Injection volume: 601 cm³ Hydraulic ejector: YES Number of hydraulic cores: 2 Cores: on the nozzle side – YES on the closing side – YES programmable – YES Motor power: 31 kW Heater power: 19.7 kW Screw diameter: 55 mm Ejector stroke: 160 mm Screw: bimetallic Machine condition Total operating hours: 79,526 h Automatic operating hours: 40,612 h TEDERIC SW6310S robot (2019) included.

Condition: used, Battenfeld BEX-1-150-32-D-V / BEX 45-25E / 89-9436-3201 extruder machine. Chjdpfx Aozump Ejknjc Manufacturer: Battenfeld-cincinnati Germany GmbH. Year of manufacture: 1999 Year of installation: 1999 Rated voltage: … V Maximum current consumption: … A Frequency: 50 Hz Required pressure: 6 bar Total weight: … kg Noise level: … dB Hydraulic pressure for the screen changer: Extrusion material output: 1000-1200 kg (filter-limited output: approx. 850 kg) Possible thickness: 1 – 5 mm Maximum width: approx. 1450-1480 mm Machine dimensions: as described in the layout. Battenfeld BEX-1-150-32-D-V / BEX 45-25E / 89-9436-3201 extruder machine Consisting of: Screw and barrel assembly, motor and drive system, control interface, and supporting auxiliary systems for feeding, thermal regulation, and downstream processing. Details: Feed station - 2x silos. 2 x metal separators - Degacan HE degassing elements, co-extruder Type BEX-1-150-32-D-V and BEX 45-25E / 89-9436-320 to produce sheets or coils. Main extruder composed of 7 heating zones and one vacuum zone. Co-extruder composed of 3 heating/cooling zones to control the polymer. Followed by 3 calenders with temperature controllers. Extrusion die - To be confirmed if included. Calender line setup. Betacontrol Mk1 thickness measuring system. Radioactive source has been removed. Calvatron corona treatment system. Kalvar Calvtron automatic coil changing system. Rollers and calibration table. End-of-line sheet separation and side cutting (slitting) machine. BC touch control interface. Full workshop manuals.

Condition: used, Year of construction: 2018, clamping force: 500 kN, screw diameter: 27 mm, clearance between the columns: 360 mm, mold height (min.): 210 mm, ejector stroke: 70 mm, opening stroke: 600 mm, plate width: 500 mm, plate height: 470 mm, Equipment: documentation/manual, For sale is a used FANUC ROBOSHOT Alpha S50iA, manufactured in 2018. This compact injection molding machine is offered based on the current technical description and the attached machine photographs. Technical specifications: - Year of manufacture: 2018 - Clamping force: 500/650 kN - Screw diameter: 27 mm - Theoretical cylinder volume: 50 cm³ - Column spacing horizontal/vertical: 360 x 320 mm - Platen size: 500 x 470 mm - Mold height: 210 to 460 mm - Maximum opening stroke: 600 mm - Maximum ejector stroke: 70 mm - Core circle diameter: 125 mm - Hydraulic cores: 0 - Pneumatic circuits: 2 - Connected power: 30 kW Equipment and options: - Power transformer AC 400 V to AC 200 V - Air ejector, 3 circuits - Short shot detection - Euromap 67 - USB interface - Parallel tool movement / dosing - Parallel tool movement / ejector - Pre-injection function - Precision dosing function Csdpfx Aszwhdioknshc - Backflow measurement at the screw check valve - Nozzle with shut-off function, software - Hot runner valve control, 8 circuits (software) - Communication with temperature controllers (software) - Intelligent tool protection - Intelligent ejector protection - Tool set - Safety set - 21 freely programmable inputs/outputs - 2 analog inputs 0-10 V DC - Alarm column with audible signal - Czech operating manual Optional services available upon request: The following services can be offered upon request and are not included in the machine scope: - 1-day operator training at the customer's site - Commissioning - Automatic clamping force correction during operation Operating hours, control system, ejector force, injection speed, injection pressure, screw/cylinder design, and robot interface are not specified. The machine is offered used and in its current condition. Technical specifications and scope of supply are to be confirmed before the contract is concluded. The written confirmed scope of supply shall prevail. Inspection and further information are available upon request.

Condition: excellent (used), Year of construction: 2006, ARBURG 320 C 400-170 injection molding machine Year of manufacture: 2006 Clamping unit Clamping force: 400 kN (40 tons) Cedpfjzw A Ehex Aknshc Distance between tie bars (H × V): 320 × 320 mm Injection unit Screw diameter: 30 mm Maximum injection volume: 85 cm³ Maximum injection shot weight (PS): 77 g Maximum injection pressure: 2000 bar Maximum screw speed: 400 rpm Nozzle stroke: 250 mm Nozzle clamping force: 40.6 kN Heating power: 9.4 kW Drive and power Pump drive power: 11 kW Total installed power: approx. 20.5 kW Dimensions and weight Machine length: approx. 3.4 m Machine width: approx. 1.4 m Machine height: approx. 2.0 m Machine weight: approx. 2,400 kg Additional information The machine is equipped with a new screw, which is covered by a warranty.

Condition: used, Year of construction: 2008, operating hours: 37,000 h, For sale is an ARBURG ALLROUNDER 630 S 2500-800 ECO injection molding machine from 2008 with extensive automation and peripherals. Manufacturer: ARBURG Chjdpfozw D Hmsx Aknec Type: ALLROUNDER 630 S 2500-800 ECO Year of manufacture: 10/2008 Clamping force: 2,500 kN / 250 t Injection unit: 800 Control system: ARBURG SELOGICA The machine is equipped with an original ARBURG Multilift V select with a load capacity of 15 kg. The system also includes a complete safety enclosure, conveyor technology, and other peripheral devices. The machine is connected to the power grid and is currently in operation in a production facility. An inspection can be arranged by appointment. Technical specifications / Design: ARBURG ALLROUNDER 630 S 2500-800 ECO Year of manufacture 10/2008 Clamping force 2,500 kN / 250 t Injection unit size 800 Spindle diameter: 55mm Control system ARBURG SELOGICA Operating voltage 400 V / 3~ / 50 Hz Control voltage 230 V / 50 Hz Total connected load 81 kW Total rated current 145 A Automation: ARBURG Multilift V select Year of manufacture 10/2008 Load capacity 15 kg Control via SELOGICA pneumatic design X-/Y-/Z-axes complete safety enclosure part removal via conveyor belt Additional equipment / Peripherals: Piovan material conveying unit material hopper conveyor belt additional conveyor belt on the machine side several temperature control / tool circuits ARBURG temperature control unit extensive media connections complete automation cell. An inspection of the machine is possible after prior appointment. Location: Greater Thuringia area _____ In addition, the following machines, not listed here, are also available: DEMAG Ergotech 50-270 – Year 2002 DEMAG ViVa 100-400 – Year 2000 DEMAG Extra 200-840 – Year 2007 DEMAG Ergotech 80-200 – Year 1995 DEMAG Ergotech 80-200 – Year 2001 ENGEL Victory 80/40 – Year 2006 DEMAG Ergotech 35/320-120 concept – Year 2002 _____ Subject to prior sale and errors in the technical specifications. The technical specifications have been compiled to the best of our knowledge, but do not constitute guaranteed characteristics. Our general terms and conditions apply, and the seller is not liable for typing or data transmission errors. The appearance of the offered items corresponds to their age and the images shown. The technology and wear of the offered items are appropriate for their age. Used machines are sold exclusively to commercial enterprises and without warranty.

Condition: good (used), Year of construction: 2008, functionality: fully functional, Ferromatik Milacron K-Tec 250 S, Year of manufacture: 2008, Control system: Moasic Control, Tool opening stroke: 850 mm, Screw diameter: 60 mm, Injection pressure: 2144 bar, Clamping force: 2500 kN, Maximum shot weight: 694 grams, Installed heating capacity: 22.7 kW, Hour meter: 5100 hours, Machine weight: 18,000 kg. Cjdpfx Akjzub Hronehc

Condition: excellent (used), Year of construction: 2021, operating hours: 6,300 h, functionality: fully functional, machine/vehicle number: ADFL9004, clamping force: 80,000 kN, screw diameter: 98 mm, clearance between the columns: 1,020 mm, column diameter: 160 mm, displacement volume: 3,142 cm³, injection pressure: 1,794 bar, injection weight: 2,890 g, mold height (min.): 400 mm, ejector force: 182,000 N, ejector stroke: 280 mm, opening stroke: 1,000 mm, plate length: 2,020 mm, plate width: 1,440 mm, plate height: 1,440 mm, total length: 11,200 mm, total width: 2,400 mm, total height: 3,300 mm, overall weight: 35,000 kg, heating capacity: 39 kW (53.03 HP), pressure: 178 bar, number of injections: 1, pump power: 116,000 W, power: 163 kW (221.62 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 312 A, Equipment: documentation/manual, The machine has few operating hours and is in very good condition. It has been well maintained. The machine processes only ABS, PP, and PS. The machine is controlled by a Beckhoff system. The machine is equipped with a variety of additional features, including 3 air valves, two hydraulic valves, a servo valve for hydraulic table movement, 8 tool heating zones, a water manifold with 8 zones, a screw heater insulation, hydraulic screw rotation for torpedo replacement, a torpedo with a locking system, an interchangeable centering ring, a Euro-map for the robot, a door with automatic opening via an electric motor, and an electrical cabinet with sockets. Water blocks are also included for both the moving and stationary tables, each with 8 connections. In addition, a number of spare parts are included, such as a complete torpedo, a screw, heaters, temperature sensors, and specific seals for the hydraulics, as well as a self-filtration filter, a torpedo wrench, and auxiliary ejector rods. The machine is sold without the robot shown in the pictures. Cjdpfxoznlhmo Aknohc

Condition: excellent (used), Year of construction: 2005, ENGEL VICTORY 2050/300 POWER injection molding machine Year of manufacture: 2005 Serial number: 155108 Control system: ENGEL CC200 Operating hours: approx. 88,000 h Design: columnless – Tie-Bar-Less Drive: hydraulic Clamping unit Clamping force: 3000 kN / 300 t Clamping system: ENGEL POWER – hydraulic, columnless Opening stroke: 900 mm Minimum mold height: 350 mm Maximum daylight opening: 1250 mm Dimensions of mounting plates: 1100 × 1000 mm Injection unit Injection unit: 2050 Screw diameter: 70 mm Injection volume: 1155 cm³ Injection weight for PS: approx. 1050 g Maximum injection pressure: approx. 1700 bar Screw L/D ratio: approx. 20:1 Control and equipment Control system: ENGEL CC200 Interface / robot preparation: yes Robot: none Hydraulic core control: 2 circuits Central lubrication system: yes Hydraulic oil cooling: yes Power supply Voltage: 400 V Frequency: 50 Hz Dimensions and weight Machine length: approx. 7300 mm Machine width: approx. 2200 mm Machine height: approx. 2500 mm Cedpfxozvdbus Aknshc Machine weight: approx. 20,400 kg

Condition: good (used), functionality: fully functional, Year of construction: 1995, machine/vehicle number: 12 28 895, total height: 2,500 mm, total length: 3,000 mm, total width: 1,000 mm, load capacity: 400 kg, main lifting speed: 8,000 mm/min, fine lifting speed: 33 mm/s, throat depth: 2,800 mm, working height: 2,500 mm, Technical specifications Manufacturer: STAHL Fördertechnik GmbH Type: T202 Load capacity: 400 kg Year of manufacture: 1995 Chedezkam Ajpfx Aknsc Supply voltage: 380 V / 3-phase / 50 Hz Lifting speed: 8 / 2 m/min Motor power: 1.3 / 1.1 kW With pendant control, chain and hook Complete with column-mounted swivel arm STAHL lifting equipment is reliable and durable, even in industrial environments. The T202 model, a 400 kg chain hoist, is known for its lifting speed of 8/2 m/min. Condition Used, industrial equipment in good condition. Sold in the complete condition as shown in the pictures. Price: 1,000 EUR STAHL 400 kg Electric Jib Crane with Electric Chain Hoist – 1,000 EUR Description For sale is a STAHL electric jib crane complete with an electric chain hoist, pendant control and lifting chain. The unit is in good used condition and is ready for operation. STAHL is a well-known German manufacturer of high-quality industrial lifting equipment, recognized for its reliability and long service life. Technical Specifications Manufacturer: STAHL Fördertechnik GmbH Model: T202 Load Capacity: 400 kg Year of Manufacture: 1995 Power Supply: 380 V / 3 Phase / 50 Hz Lifting Speed: 8 / 2 m/min Motor Power: 1.3 / 1.1 kW Electric Chain Hoist Pendant Control Included Lifting Chain and Hook Included Complete Jib Crane Assembly Condition Good working condition Complete unit Ready for installation Industrial quality German equipment Included Electric chain hoist Jib crane Pendant control Lifting chain Hook Price: €1,000 Location: Hungary Seller: Variflux Kft.

Condition: used, Year of construction: 2021, For sale: 10L jerrycan blow mold + AdBlue spout mold (2-cavity) For sale: industrial blow molds (extrusion blow molding), suitable for the production of plastic containers and accessories. The lot includes: 1) 10-litre jerrycan blow mold Industrial blow mold designed for the manufacture of 10L plastic jerrycans. The mold is complete, in very good mechanical condition, and ready for installation on a blow molding machine. Specifications: - Production of 10L jerrycans - Process: extrusion blow molding - Hardened steel construction - Cavity with integrated handle - Hydraulic/pneumatic closing and guiding systems - Precisely machined surfaces Chedpfx Aex E U R Ueknoc - Previously used in industrial production - Stored on pallet, ready for transport 2) AdBlue spout mold – 2-cavity The lot also includes a 2-cavity mold for the production of AdBlue spouts/nozzles. Specifications: - 2-cavity mold for AdBlue spouts - Suitable for extrusion blow molding - Robust steel construction - Complete tool, ready for production - Ideal for the manufacture of accessories for jerrycans These molds are ideal for manufacturers of plastic packaging, industrial jerrycans, chemical containers, or AdBlue-related products.

Condition: used, -Model: Regamat R92 Chjdpfjwydabox Aknoc -Manufacturer: Winkler -Serial No.: 52217 -5-row dough molding machine Ndey Tdxujwydabsgja -Ready for weighing: 35–85g -Voltage: 400V -Power: 2.8kW -Year: 2000

Condition: excellent (used), Year of construction: 2009, operating hours: 63,700 h, 1,0 St. gebr. Spritzgießmaschine Hersteller: ARBURG Typ: 270S400-70 Baujahr: 2009 Schließkraft: 40 Tonnen Holmabstand 270 x 270 mm Schnecken DN: 18 mm Codpfxjxq R D Eo Aknjhc Dosiervolumen: 23 ccm³ Spritzteilgewicht 21 g/PS Steuerung: SELGOCIA Ausstattung: -Schnittstelle Roboter -Vertikale Einspritzung Betriebsstunden: ca. 63.700 Hours

Condition: used, Year of construction: 2003, operating hours: 39,000 h, functionality: fully functional, 1,0 St. gebr. Zweikomponenten Spritzgießmaschine mit Roboter Hersteller: ARBURG Typ: 420C1300-350-60 Baujahr: 2003 Schließkraft: 130 Tonnen Holmabstand 420 x 420 mm Schnecken DN 1: 35 mm Spritzteilgewicht in PS: 127 g Schnecke DN 2: 25 mm Spritzteilgewicht in PS: 45 g Steuerung: Selogica Ausstattung: .Kernzug Cedpfoy Snapox Aknjhc -Roboter

Condition: excellent (used), Year of construction: 2004, 1,0 St. gebr. Spritzgießmaschine Hersteller: DR. BOY Typ: 22 D Chodszardgspfx Aknec Baujahr: 2004 Schließkraft: 22 Tonnen Holmabstand: 254 x 254 mm Einbauhöhe MIN, / MAX. 200 / 400 mm Schnecken DN: 22 mm Spritzteilgewicht 27 g/PS

Condition: ready for operation (used), A heated platen forming press Italpresse in bottom piston design is available. Press force: 660t, platen dimensions X/Y: 1900mm/1600mm, heating power: 31kW, connected load: 108kW, rapid stroke cylinder diameter: 70mm, weight: approx. 28000kg. Documentation available. An on-site inspection is possible. Chedoyxgrdjpfx Aknsc

Condition: ready for operation (used), An injection molding machine Maplan for elastomers requiring repair is available. Design: hydraulic vertical press, hydraulic oil type: ISO VH 46 HLP, hydraulic oil filling quantity: approx. 600l, max. hydraulic pressure: 250bar, heating cartridge diameter: 25mm, insulation plate thickness: 14mm, max. operating temperature: 250°C, L/D ratio: 12:1, max. back pressure: 400bar, max. stroke: 260mm, vacuum pump capacity: 63m³/h, weight: approx. 17500kg, control system: B&R PLC. The temperature control units and the hydraulic clamping system have failed. Documentation available. An on-site inspection is possible. Cedpfx Akjzcfi Ienohc

Year of construction: 1999, condition: ready for operation (used), A two-component injection molding machine Krauss Maffei Multinject is available. Clamping force: 3500kN, platen dimensions X/Y: 1280mm/1190mm, second unit: 390CZ. Machine dimensions X/Y/Z: approx. 6300mm/2000mm/3100mm, weight: approx. 17000kg, control: Krauss Maffei MC4, operating hours: 78424h. The control is defective. Documentation vorhanden. An on-site inspection is possible. Chedpfx Akexx Uf Ajnoc