Used Manual Bending Machine Pan for sale (73,474)

Condition: new, 40 mm 8,5 U/min 120 mm roll diameter 152 / 162 mm engine output 1,1 kW connected load 400 V weight 395 kg Overall size 900x600x1100 mm Equipment / Accessories: - Two driven rollers - Manual delivery of the upper roller Fgodpfx Afjyv N A Tjfea - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used

Condition: new, 95 mm Shaft diameter 30 mm Shaft revolutions 7 U/min roll diameter 132 mm Drive 0,75 kW weight 220 kg range L-W-H 530x900x660 mm Equipment / Accessories: - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc. Fsdpfeyv N A Hjx Affoga

Condition: new, I-beam section - flat steel 80x20 (d1200) mm I-beam section - upend 80x25 (d2100) mm L-beam 50x50x6 (d1000) mm bar material - diameter 40 (d800) mm square material 60x60x3 (d4000) mm rectangle 80x30x3 (d6000) mm tube diameter max. 70x2 (d1600) mm tool adaptor 60 mm roll diameter 177 mm bending speed 6,4 m/min total power requirement 4 kW Fgodpfx Aoyv Nwqeffea machine weight ab. 970 kg Overall size 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German

Condition: new, sheet width 2100 mm plate thickness 40 mm pre-bending 30 mm upper roll diameter 390 mm Fgodpoyv Nt Eofx Affoa lower roll diameter 360 mm side roll diameter 300 mm total power requirement 22 kW machine weight ab. 17200 kg Overall size 5060 x 2200 x 2180 mm

Condition: new, I-beam section - upend 100 x 20 (d 2100) mm tube diameter max. 100 x 3 (d 3000) mm Fgjdpfxsyv Nnij Affja L-beam 80 x 80 x 8 (d 2000) mm square material 50 x 25 x 2 (d 600) mm bar material - diameter 60,0 (d 1000) mm I-beam section - flat steel 120 x 30 (d 600) max. 140 mm tool taper 80,0 turning speeds 4,2 U/min weight 1600 kg dimensions 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according to CE, ISO 9001 - 2015, TSEK and TURQUM Additional equipment: - hydraulically adjustable straightening rollers

Condition: new, round material 40 mm tube diameter 70x2 mm square material 80x30x3 mm L-beam 50 x 5 mm roll diameter 157 mm I-beam section - upend 50 x 15 mm I - beam section - flat steel 80 x 16 mm Shaft diameter 50 mm bending speed 2,95 m/min total power requirement 1,1 kW weight of the machine ca. 500 kg dimensions of the machine ca. 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication Fgedpfxoyv Nk Rs Affsa - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German

Condition: new, sheet width 3100 mm plate thickness 13 mm pre-bending 10 mm upper roll diameter 300 mm lower roll diameter 270 mm side roll diameter 210 mm total power requirement 11 kW Overall size 5600 x 1800 x 1500 mm weight of the machine ca. 8.800 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel Fedpfx Ajyv Nh Neffoga - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration

Condition: new, sheet width 3100 mm plate thickness 10 mm Fjdpfx Aoyv Nhcjffsga pre-bending 8 mm upper roll diameter 270 mm lower roll diameter 250 mm side roll diameter 210 mm total power requirement 11 kW weight of the machine ca. 7750 kg Overall size 5600x1450x1600 mm

Condition: new, sheet width 2100 mm plate thickness 6 mm pre-bending 4 mm upper roll diameter 160 mm lower roll diameter 140 mm side roll diameter 120 mm total power requirement 2,2 kW Overall size 4140x1040x1140 mm weight of the machine ca. 2.350 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) Fsdpfeyv Nf Uox Affoga - Calibration

Condition: new, sheet width 3100 mm plate thickness 6 mm pre-bending 5 mm upper roll diameter 200 mm min. bending diameter Ø 300 mm bending speed 5 m/min total power requirement 5,5 kW weight of the machine ca. 4.000 kg Fgodpfoyv Nf Ijx Affoa dimensions of the machine ca. 4800x1300x1270 mm

Condition: new, sheet width 1050 mm plate thickness 3,3 mm pre-bending 3,0 mm roll diameter 90 mm min. dia. 130 mm total power requirement 1,1 kw weight of the machine ca. 570 kg dimensions of the machine ca. 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive Fsdpfx Afsyv Nfbefoga - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls

Condition: new, sheet width 1050 mm plate thickness 1,8 mm pre-bending 1,5 upper roll diameter 70 mm min. dia. 105 mm total power requirement 1,1 kW Fsdpfx Afoyv I U Iofega weight of the machine ca. 320 kg dimensions of the machine ca. 1700x700x1100 mm

Condition: new, R10-R260 max. 210 ° 54x2 mm Fgsdpfx Afjyv I Uhofsa 42x2,5 mm 42x3,5 mm 30 mm bending speed max. 4 U/min Amount of programms 30x9 voltage dreiphasig 220-400 V total power requirement 1,1 kW dimensions of the machine ca. 1000 x 410 x 570 mm weight of the machine ca. 80 kg Accessories / equipment: - Machine structure: aluminum alloy - Base: welded steel - Standard accessories (including footswitch, operating instructions)

Condition: new, sheet width 2100 mm plate thickness 13 mm pre-bending 10 mm upper roll diameter 230 mm lower roll diameter 210 mm side roll diameter 190 mm total power requirement 7,5 kW weight of the machine ca. 4.750 kg dimensions of the machine ca. 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel Fgedpjyv I Ubefx Affea - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration

Condition: new, R10-R260 Fedpfsyv I Tkjx Affsga 210 ° bending speed 2 U/min 1 1/4" x 3,5 mm einphasig - 230 V drive motor 1,1 kW < 70 dB weight of the machine ca. 80 kg dimensions of the machine ca. 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed

Condition: new, 300 kN Fodpfxjyv I Tde Affega stroke length max. 235 mm 200x24 mm bending capacity max. - round 60x4,0 mm toolpiece height max. 250 mm 660x1250 mm work height max. 900 mm return speed 20 mm/sec working feed 10 mm/sec total power requirement 3 kW weight 950 kg Domestic equipments: - semi-automatic NC control (99 programs with 16 steps each) - incl. bending bolt (without punch) - Incl. tool holder for dies - incl. foot pedal Equipment: - Stamp, smallest U = 145 mm 85 °    H = 250 mm, R = 5 mm - Quick change Monomatrize 85 °    H = 250 mm, V = 63 mm

Condition: new, sheet width 3100 mm plate thickness 16 mm pre-bending 13 mm upper roll diameter 330 mm lower roll diameter 300 mm side roll diameter 240 mm total power requirement 11 kW Overall size 5600x1650x1900 mm weight of the machine ca. 10.600 kg Accessories / equipment: - Conical bending device Fgjdpfoyv I Smex Affea - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration

Condition: excellent (used), Year of construction: 1992, Shaft diameter: 40 mm Bending capacity: Flat bar edgewise at 500 mm Ø: 60 x 10 mm Flat bar flatwise at 400 mm Ø: 100 x 15 mm Square bar at 500 mm Ø: 35 mm Angle iron, leg outwards at 450 mm Ø: 50 x 50 x 6 mm Angle iron, leg inwards at 600 mm Ø: 50 x 50 x 6 mm Fgedpfx Afjx Anpvofja T-section, T outwards/inwards at 600 mm Ø: 60 x 60 x 7/50 x 50 x 6 mm Round bar at 500 mm Ø: 35 mm Shaft speed: 7.5 rpm Electrical connection: 380 V, approx. 1.7 kW Space requirement: 910 x 640 x 1400 mm Weight: approx. 480 kg

Condition: new, sheet width 1050 mm plate thickness 1 mm Fjdpfx Aeyvvn Asffega roll diameter 56 mm dimensions of the machine ca. 1600 x 700 x 1050 mm Domestic equipments: - Upper roller can be swung out manually

Condition: excellent (used), Year of construction: 2018, You are bidding on: a branded folding machine from the renowned top manufacturer Schröder Device Features: - Schröder folding machine - Bends sheet metal up to 1 mm steel, aluminum, etc.; up to 1.5 mm - Bending length just over 2 meters - Angle gauge - Foot closer - Pneumatic support (use is possible without compressed air as well; with the pneumatic support, bending can be performed almost hands-free with fingertip control via the handle grip, significantly easing strain on the back) Optional equipment available on request: additional front rail and radius rail (round bar), as well as rotary shear and depth stop with finger guard, compressor, etc. Matching guillotine shear or mechanical/electric shears for 1 meter sheets also available—package price possible and can be arranged on request. The machine is in the usual high quality; it has not been used for the past two years due to business closure. Optionally, you can find and purchase many other machines and machine accessories such as various rails, depth stops—everything needed for sheet metal and steel processing including folding machines, guillotine shears, drills, slip rollers, slitting and profiling machines, accessory parts (beading units, round rollers for gutter production, backgauge, etc.), as well as other hand tools and spare parts from many top manufacturers in our shop. Please feel free to contact me with any questions. You will receive an invoice with VAT shown. Fsdpfsyx S H Tex Affjga Free loading possible – machine weight approx. 1050 kg. Viewing and testing are possible by prior telephone appointment. Payment in cash upon collection. Benefit from our experience and expertise—we are happy to advise you. Collection by the buyer (or by a forwarding agent commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97261 Güntersleben Article number: Schröder Folding Machine 2m

Condition: good (used), Guillotine Shear HT 200 Capacity: 1.25 mm steel – aluminum and more Cutting length: slightly over 2 m Back gauge Extendable front support Folding Machine KS – Capacity: 1 mm steel – more for aluminum (up to 1.5 mm) Bending length: slightly over 2 m Foot closer Optional: back gauge or Beading device Roller sets and additional rails Sold according to §25a of the German VAT Act Machines are in proper condition and immediately operational Important! Optionally, you can find and purchase many machines and machine accessories in our shop, such as various rails, back gauges – everything related to sheet metal and steel processing, including folding machines, guillotine shears, drill presses, slip rollers, slitting and profiling machines - accessories (beading devices, round rollers for gutter manufacturing, rear gauge, etc.), as well as other hand tools and spare parts from many top manufacturers. Please feel free to contact me with any questions. You will receive an invoice according to §25a UStG (the VAT is included in the amount – margin scheme taxation). Free loading available – weight approx. 750 kg and 650 kg. Fjdpfeyknd Rex Affsga Inspection and test run are possible and encouraged after making a telephone appointment. Payment in cash upon collection. Benefit from our experience and expertise – we are happy to advise you. Collection by the buyer (or a shipping company commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97249 Eisingen, approx. 3 minutes from motorways A3 and A81. Item numbers: Folding Machine KS and HT 260107 260108

Condition: excellent (used), You are bidding here on a branded guillotine shear from the well-known German manufacturer Schechtl, in absolutely top condition! Device features: - Shear model: MSB 200 - Cutting capacity: see nameplate, up to 3mm steel – significantly more for aluminum - Working length: just over 2 meters - Manual back gauge: 500 mm - Side / angle gauge - Foot pedal operation - Weight approx. 1.3 t - Schechtl MSB 200 - Bending length: just over 2 meters - Sheet thickness (steel): 3 mm – significantly more for aluminum and zinc - The machine was used extremely rarely, approx. 1-2 times per month for thin sheets at a lamp manufacturer - It shows hardly any signs of use; this condition is rare - The total price is less than half the current new price – the price list is from last year! If you have any questions, feel free to call briefly. We have this set twice, as well as other models such as the Schechtl MAX 200 (2.5mm) or MA 200 (2mm). The current net new price for both machines can be seen in the photos. You will receive an invoice with VAT shown separately. I can arrange shipping by freight forwarder if desired; a forklift is available. Free loading as shown in the pictures. Inspection and testing are possible by prior telephone arrangement. Payment in cash upon collection – if there is anything else I can do for you, please call me briefly – thank you. Collection should take place within 8 days after the end of the auction. Item number: Fgsdpfswfzztex Affsa

Condition: good (used), Year of construction: 1988, Work piece thickness 0,4 - 8 mm Work piece height max. 51 mm Min. work piece width 50 mm min work piece length 180 mm edge magazine for PVC and strips pneumatic pressure rollers for edge magazine edge snipping unit Fsdpfjbahd Eox Affjga cutting unit with 2 saws milling aggregate buffing unit Feed speed 11 m/ min Glue application with fin nozzle Air pressure 6 bar length 3750 mm

Condition: good (used), Year of construction: 2005, control type: CNC control, - Max. bending angle: +/- 180 + 10° - Tube feed length: 4100 mm Fodpfeyx Ur Sjx Affoga - Round steel tube up to 30 x 2.2 mm² - Round stainless steel tube up to 30 x 1.5 mm - Square tubes: 20 x 2.5 mm - Bending time for 90 degrees: 1.5 sec (advance) - Longitudinal feed speed: 450 mm/sec - Maximum bending radius: 125 mm - Freestanding bending head, 850 mm long - Bending axis drive: electrohydraulic

Condition: good (used), Year of construction: 2008, control type: CNC control, Stainless steel tube diameter: up to 42 x 2.0 mm Steel tube diameter: up to 42 x 3.0 mm Max. bending angle: +/- 180 + 10° Section modulus: 4.1 ccm Operating pressure: 6 bar Total power requirement: 5.5 kW Machine weight approx.: 3 t Space requirement approx.: 6100 x 2300 x 1300 mm Fgedpfx Afjyx Un Hefja