Used Paper Spindle for sale (14,586)

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake Hfsdovivmyjpfx Ad Djp >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: reconditioned (used), Year of construction: 1956, Lead and Feed Screw Lathe WEIPERT Year of manufacture: 1956 Spindle bore: 90 mm Centre distance: 3000 mm Swing over bed: 800 mm Swing over cross slide: 610 mm Swing in gap: 1120 mm Hfedjw Ew D Dopfx Ad Djp Speed range: 7.5 – 475 rpm Comes with the following accessories: Multifix toolholder with 11 inserts Coolant system 3-jaw chuck 315 mm 3-jaw chuck 400 mm 3-jaw chuck 500 mm Faceplate 400 mm Faceplate 800 mm Faceplate 1000 mm Travelling steady Various turning tools (30 insert tools) 2 revolving centres 1 drill chuck Operating manual

Condition: excellent (used), Year of construction: 2004, We are offering an exceptionally high-quality precision lathe. Within its class, this is likely the best German lathe ever built. BOEHRINGER Precision Lathe Model DUE 500 Year of manufacture: 2004, including CE certification and central lubrication Machine No.: T1022.2027-00 Center height: 240 mm Swing diameter over bed: 500 mm Swing diameter over cross slide: 285 mm Center distance: approx. 1,200 mm Effective turning length: approx. 1,000 mm Bar capacity: 62 mm Spindle nose: DIN 55027 Size 6 Spindle bore: 100 mm Drive power: 11 kW Maximum torque: 2,000 Nm 24 spindle speeds: 11.2 – 2,240 rpm 60 cross feeds: 0.03 – 28 mm/rev 60 longitudinal feeds: 0.06 – 56 mm/rev Tailstock quill stroke: 190 mm Tailstock taper: MK 5 Machine footprint (LxW): approx. 4,000 x 1,525 mm Weight: approx. 4,300 kg Accessories: - HEIDENHAIN 3-axis digital readout - Central lubrication system - Electrically interlocked chuck guard - Coolant system - Chip protection rear panel - Röhm chuck, T 250 mm, with various jaws - Telescopic cover for lead and feed screw, support to bed - Machine lamp - Multifix C + 4 quick-change tool holders - Live center - Operating manual Hfedpfx Aow Rdthod Dsp - Circuit diagram - Rapid traverse in longitudinal and cross slides Condition: The machine is in very good technical and visual condition. Backlash on cross slide approx. 0.3 mm, on compound slide approx. 0.15 mm Spindle nose runout approx. 0.006 mm Bed geometry: deviation approx. 0.01 mm over approx. 750 mm bed length (measured on flat guideway towards chuck using dial indicator) The following parts have been renewed: - Oil change - New hoses for central lubrication - New wipers - Key for operating lever replaced - Locking pin for interlock replaced Price is net, ex stock, loaded free of charge. Delivery by company truck can be arranged at extra cost.

Condition: used, Year of construction: 1979, functionality: fully functional, Leadscrew and feed rod lathe Make: WEILER Model: COMMODOR Year: 1979 Technical Data Manufacturer: Weiler Model: Commodor Centre distance: 1000 mm Swing over bed: 400 mm Spindle bore: 50 mm Speed range: 63-2000 rpm Drive power: 4 kW Dimensions: approx. L 2.2 x W 1.0 x H 1.7 m Weight: approx. 1.5 t Equipment • 3-axis digital readout • Drill chuck • Röhm 3-jaw chuck, D 200mm • Multifix toolpost • The additional 3-jaw chuck shown on the machine is not included in the scope of delivery! All information without guarantee. Hfjdpfxsxt Ngqj Ad Dep A demonstration under power is possible at any time in our showroom.

Year of construction: 2014, condition: refurbished (used), Now available: Mueller Apparatebau unwinder 6802C available. Completely refurbed and like new. Direct available for your production. Hedpshd Nxvjfx Ad Djfp

Condition: good (used), Centre height: 290 mm Swing over bed: 580 mm Centre distance: 3000 mm Equipped with a flat belt grinder, e.g. for shaft or pipe grinding Hedpfx Adoxtu Erj Djfp Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Weiler precision lathe model Condor B, lead and feed screw lathe with brand new K&C 3-axis digital readout, CE compliant! Technical data: >> Machine No. 2442, year of manufacture 1997 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Camlock spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting: metric, imperial, module and diametral pitch threads possible >> Metric thread pitches: 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake, selectable >> Length: 1.83 m, height: 1.29 m, depth: 0.88 m Equipment and features: >> New K&C 3-axis digital readout, 12-month manufacturer's warranty, supplied with operating manual Features: mm/inch switching, selectable ABS/INC coordinates, value halving function, reference mark, tool memory for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 x brand new 160 mm 3-jaw chuck with 2 sets of jaws >> 1 x 200 mm 4-jaw chuck with 1 set of jaws >> New collet chuck system and new collets from 3 to 25 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear splash guard Hfsdpfexcuazex Ad Dop >> Machine feet Safety features: electronic spindle guard, 2 emergency stop buttons, changewheel box with safety interlock, spindle brake About the machine: Offered here is a Weiler Condor in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new K&C 3-axis digital readout makes work easier and more precise. The machine has been electrically and mechanically checked by us. A complete oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power on site.

Condition: like new (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 9011221, Colour touchscreen, side tables with air, chrome-plated cutting table with air Hfjdpfx Adjxrzklj Dep

Condition: good (used), Lead and feed spindle lathe Matra SM-3000 Country of origin: Spain Turning diameter over bed 600 mm Turning diameter over support 370 mm Turning length 3000 mm Turning diameter in the crank 900 mm Length of the crank 280 mm Spindle bore 72 mm Speed range 17-1,652 rpm Spindle speed levels 36 Main motor, power 9/11 kW Rapid traverse longitudinal-transverse Tailstock MK5 Machine weight approx. 4 t Dimensions (LxW) approx. 4800x1300mm Equipment/accessories: - Fixed steady rest with rollers/max. Workpiece diameter 220 mm - Coolant system - Bed stop - Röhm lathe chuck D500mm Hodpovq I Npsfx Ad Dsfp - Digital display 2-axis SINO - Multifix C base holder The machine is in very good, fully operational condition. Price net, free loading from warehouse

Condition: used, Year of construction: 1999, total height: 1,710 mm, total width: 2,040 mm, total length: 1,000 mm, Empty weight: 900 kg - Year: 1999 - Documentation available: No Hfodjwnigcepfx Ad Dop - Serial number: 126-02049 - Main motor power [kW]: 7.8 - Spindle diameter [mm]: 40 - Table length [mm]: 1990 - Max. tool diameter milling head [mm]: 180 - Feeding device present: Yes - Brand: Holz-her - Number of wheels [pcs]: 3 - Number of speeds: 2 - Voltage [V]: 380 - Current consumption [A]: 12 - Power [kW]: 6.2 - Transport dimensions: 1000mm x 2040mm x 1710mm (l x w x h) - Transport weight [kg]: 900kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: refurbished (used), Year of construction: 2013, We have multiple Mueller Apparatebau paper cutting systems available! Paper cutters fo pin feed available. We offer all machines after complete maintenance. We mostly have model 6612 but we also have a paper cutter system type 6611. Next to that we have a lot of other Mueller modules like unwinder, collating module and folding modules etc etc! Hjdstwc Abspfx Ad Dsfp Just let us know and we have the solution!

Condition: good (used), Centre height: 360 mm Centre distance: 5000 mm Swing diameter over bed: 720 mm Swing diameter over cross slide: 560 mm Swing diameter in gap: 1000 mm Spindle bore: 82 mm Speed range: 16 - 800 rpm Bed width: 445 mm Hjdpfoxtu Duex Ad Dsfp Tailstock taper: MT 6 Drive power: 11 kW Dimensions (L x W x H): 6750 x 1500 x 1700 mm Weight: 6500 kg Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch Hedpfxew Idllj Ad Dsfp >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: good (used), Originating from a school. Nice and complete with accessories. Details: Turning diameter: 300 mm Turning length: 430 mm Swing diameter over bed slide: 160 mm Turning diameter over bed slide (with T-slots): 135 mm Centre distance: 470 mm Centre height: 145 mm Bed width: 205 mm Number of spindle speeds: 18 Speed range: 30 - 3550 rpm Speed range: 15 - 3550 rpm Hjdpfjw Ryhnjx Ad Dsfp Number of feeds: 90 Feed range: 0.02 - 2.0 mm/rev Workpiece weight in steadies (max.): 25 kg Workpiece weight without steadies (max.): 80 kg Machine weight approx.: 0.9 t Total power requirement: 3.5 kW Machine dimensions approx.: 1475 x 795 x 1300 mm Quill diameter: 40 mm Quill stroke: 85 mm Control unit: Conventional

Condition: reconditioned (used), We are offering an exceptionally good precision lathe. The machine is probably the best German lathe that has been built in this class. BOEHRINGER precision lathe model DUE 800 Year of manufacture: 1984 Order no.: 04041.01-807 Center height: 400 mm Circulation diameter over bed: 820 mm Circulation diameter over facing slide: 515 mm Center width: approx. 2200 mm Effective turning length: approx. 2000 mm Bar passage: 128 mm Spindle head DIN55022 size 11 Drive power: 30 kW Max. Torque: 6300 Nm 24 Speeds: 7.1 - 1400 rpm 60 face feeds: 0.05 - 28 mm/rev 60 longitudinal feeds: 0.06 - 56 mm/rev Rapid traverse in longitudinal cross feed Motorized top support Tailstock quill stroke: 280 mm Tailstock taper: MK 6 Space requirement: LxWxH approx. 6700x2500x2250mm Weight: approx. 7500 kg Accessories: 3-axis digital readout HEIDENHAIN Coolant device; chip protection rear panel, power chuck autoblock 500 mm with clamping jaws, roller conveyor cover for lead screw support to bed, machine light, chip conveyor, Parat basic holder incl. 11 holders, suction unit, 3-jaw steady rest with roller inserts (moving), emergency stop, chuck key, moving center point, operating instructions Condition: The machine is in very good technical and optical condition. Hedpfx Ajrt T S Rjd Dofp Backlash in the top slide 0.1 mm and face slide 0.15 mm The geometry of the machine is also very good (was checked with a dial gauge) Measured on the flat track guide with dial gauge in the direction of the lathe chuck Bed wiper replaced, gearbox input shaft axial play compensated and bearings replaced, drive pins on motor/gearbox side replaced, shaft seals on lock case replaced, various bearings replaced The machine can be demonstrated under power. Functional videos can also be sent on request.

Condition: used, Milling Spindle Manufacturer: HSD Type: ES 779L 4P 12.00 kW H1 Hedpfxswyay De Ad Dsfp HSD 12 kW milling spindle with tool changer and 6-position station for Kuka Quantec series Comprising: 1 piece Water-cooled milling spindle with HSD tool changer ES779L 4P 12.00 kW H1, Liquid cooling 1 piece Tool station for 6 tools (toolchanger station) with Leonie measuring station for tool inspection 1 piece Kuka tech cabinet with KEB frequency converter, control equipment and water cooler, Part No. 00216249, Serial No. 0395009, Year of manufacture: 2018 Weight: 360 kg 1 piece Hose package and connection cable from the control cabinet to the HSD spindle. Originally designed for a Kuka robot of the Quantec series. All holders and connectors are included.

Condition: used, Year of construction: 1966, Swivelling spindle: No Height adjustment: Handwheel Swivel adjustment: - Cutter jaw adjustment: manual Height display: Scale Swivel angle display: - Fence indicator: Scale Spindle diameter: 30 mm Speeds: 2800, 4500, 6000, 5600, 8000, 12000 rpm Motor power: 4 / 5.5 kW Motor brake: Manual Extraction connection: 2 x 120 mm Hjdpfoxu Dhlex Ad Dofp Machine length: 2000 mm Machine depth: 900 mm Weight: 700 kg

Condition: used, functionality: fully functional, Setmaster 5040 automatic sheet collating machine with jogger.) 24 deep-pile suction-fed stations, each of which is programmable. Suction cups to provide a gentle contact with the paper to avoid marking Touch screen programmer to control all functions, including the inserting facility. Production speed: Approx 1,900/2,600 cycles per hour. (adjustable speed control) Sheet size: Max 52cm x 42cm. Paper weight: 15 - 1,000 gms on all types of material Miss detection at each station with a double detector on exit Self-elevating 40cm capacity deep pile feed stations with programmable control Exit jogger with adjustable height, tilt and speed. Becker SVT 3.100 high-performance suction pump Power Supply: 400/440 volts - 3 Phase - 50Hz - 16a Can be seen running and available for inspection in West Yorkshire. We can arrange for delivery and installation services in the UK. POA Hsdpfxjxg Hz Eo Ad Defp This machine has been regularly maintained with a Setmaster-trained technician. ( Also available for installation and training) Please do not hesitate to ask if you need more information.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev Hsdpfxewrmuxs Ad Djfp >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.

Condition: used, functionality: fully functional, In this offer you purchase a used paper cutting table "PFi Blade B2+" Hedjw Dm Ddjpfx Ad Dsfp Object of sale: 1 x PFi Blade B2+ with the following equipment: incl. accessories as shown in the pictures from 2021 Condition: This offer is a used device, which may show signs of use (minor scratches or yellowing). The device has been tested for function, the function test ran without problems. Packaging and dispatch: You are welcome to view the device during our business hours. Please make an appointment for this! Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before dispatch or collection. For further information, you can of course also contact us personally.

Condition: good (used), Year of construction: 1994, spindle drilling machine 1994 (engine new 2015) machine no.: PB04.08.94.261 4 drill heads, can be upgraded to 6 drill diameter: 3mm to 14mm Hfedpfx Adsvccnks Djp hole spacing: 31.7mm to 293mm hole spacing using the sliding table: 1mm to 420mm located: Germany Insertion depth behind the drills: 25 mm sliding table width: 450 mm Sliding table size in front of the drills 300 mm maximum stacking height: 50 mm power requirements: 230/400 volts 3 phases, 50 Hz, 1.87 kWh. space requirement: 770mm (W) x 760mm (D) x 1350mm (H) weight: 275 kg net located: Germany available: immediately

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Weiler Center Lathe Model Condor B Guide & Feed Shaft Lathe with 3-Axis Digital Readout by K&C NEW from Training Workshop!! Technical Data: >> Machine No. 91-1814, Year of manufacture: 1991 >> Center height: 165 mm >> Distance between centers: 750 mm >> Spindle speeds: from 22 to 2,800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet locking >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Threads possible: Metric, Imperial, Module, and Diametral Pitch >> Metric thread leads: from 0.18 to 28 mm >> Weight: approx. 1,100 kg >> Spindle brake switchable >> Dimensions (L x H x D): 1.83 m x 1.29 m x 0.88 m Scope of Delivery and Features: >> NEW 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating manual Functions: mm/inch switch, ABS/INC coordinate selection, display value halving, reference mark, tool programming for 200 items, taper calculation, radius/diameter display, quick zeroing, counting direction reversal >> 1 pc. NEW 160 mm 3-jaw chuck, 2 sets of jaws >> 1 pc. 160 mm 4-jaw chuck, 1 set of jaws >> NEW collet chuck and NEW collets from 2 to 24 mm, incremented by 1 mm >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle safety guard >> Rear splash guard Hfsdpfx Aow Nw Dqed Dop >> Fixed steady rest >> Machine feet Safety features: electronic spindle guard, 2 emergency stop switches, change gear cover with limit switch, spindle brake About the machine: We are offering a Weiler Condor in very good condition. The machine is, of course, fully operational. It is a very robust and powerful lathe. The brand new 3-axis digital readout from K&C makes operation even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change has been performed. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine under power at our premises.

Condition: good (used), Technische Daten: Bohranlage 345-31 WHT-Nr. 147-0338 SNr. 103 563 Lineareinheit M4: Fanuc, Typ: Beta is 4/4000 HV A06B-0064-B203 Motor: in Steckerausführung mit Resolver Resolverleitung und Motorleitung: PM505CBL2040B 10 319V 50Hz 2,3A 3,5Nm , 3000 U/min Bohrband M3: Astro, Typ: ASM 46 SG10 3-400V 50/60Hz 65/60mA 4/4,8min-1 Spindelantrieb M1: Bonfiglioli, Typ: BN 132 S 6 Hfodpsird U Rsfx Ad Dsp Nr. 802002 Cod: 8D62030016-519951 230V / 460V 13,5A / 7,8A 50H7 940 min' 3kW cosQ 0,76 IP 55 IsKI.F Hubantrieb M2: Fanuc, Typ: Beta 22/2000 HV is A06B-0086-B503 Motor: in Steckerausführung mit Resolver und Bremse Resolverleitung und Motorleitung mit Bremse: PM505CBL2020B 5 448V 50Hz 3,4A 22Nm, 2000 U/min Einlageband M10 : SEW / Maschienenbau Kitz, Typ: WF 10DT56LA/TF Nr: 01.1230640901.0001.08 230V / 400V 50Hz 0,80/0,46A 0,12kW 1600 U/min cos 0,68 Auslageband M11: SEW / Maschienenbau Kitz, Typ : WF 10DT56LA/TF Nr.: 01.1230640901.0001.08 230V / 400V 50Hz 0,80/0,46A 0,12kW 1600 U/min cos 0,68 Available: immediately Located: Germany

Condition: excellent (used), Year of construction: 1983, functionality: fully functional, Weiler Center Lathe Model Condor 81 Lead and Feed Lathe with 3-Axis Digital Readout from K&C NEW Technical Specifications: >> Year of Manufacture 1983 Machine No. 83-067 >> Center height 165 mm >> Center width 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MT 3 >> Feed rates from 0.015 to 0.46 mm/rev >> Possible threads: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be switched on >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and Equipment: >> New 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating instructions Functions: mm/inch switching, ABS/INC coordinate selection, halving of the display value, reference mark, 200 tool programming, cone calculation, radius/diameter, quick zeroing, counting direction switching >> 1 new three-jaw chuck, 160 mm, 2 sets of jaws >> New collet chuck and new collets from 3 to 26 mm, 1 mm increments >> Multifix size B with 3 tool holders >> Electronic spindle protection Hfjdpfewb Supex Ad Dep >> Rear panel >> Coolant system >> Machine feet About the machine: Offered is a used Weiler Condor 81 in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new 3-axis digital readout from K&C makes work even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was also performed. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to view and try out this machine live on-site.

Condition: good (used), Year of construction: 2000, Wohlenberg 155 CUT-TEC Hodpfx Adowylf Ss Djfp Reference No.: CU-001414 Cutting line Year: 2000 Width: 155 cm With monitor Programmable Air table Baumann Jogger BSB 6L Baumann Unloader BA 6N Baumann Pliers Transport System BFS-R HV Complete line Regular service In stock Available: immediately Location: Germany