Used Preset Counter for sale (2,785)

Condition: excellent (used), Year of construction: 2017, operating hours: 627 h, functionality: fully functional, total length: 6,900 mm, total height: 1,800 mm, total width: 1,600 mm, type of input current: three-phase, input voltage: 400 V, input current: 62 A, passage height: 300 mm, overall weight: 1,200 kg, passage width: 800 mm, input frequency: 50 Hz, nominal power (apparent): 43 kVA, throughput speed: 20 mm/s, temperature: 250 °C, Equipment: documentation/manual, BVM SC 8530 D3 Shrink Tunnel – Year of Manufacture 2017 – approx. 627 operating hours For sale is a BVM shrink tunnel SC 8530 D3, year of manufacture 2017, in technically flawless and visually very good, well-maintained condition. The system has only approximately 627 operating hours and is suitable for shrinking packaging films using hot air circulation. The adjustable tunnel transport and the adjustable side and bottom air flow allow the shrinking result to be adapted to different products and films. Technical data Manufacturer: BVM Brunner GmbH & Co. KG Type: SC 8530 D3 Year of manufacture: 2017 Machine no.: 20170962241 Commission no.: 6224 Operating hours: approx. 627 h Mains voltage: 3N 400 V Mains frequency: 50 Hz Current consumption: 62 A Power: 43 kVA Fuse rating: 63 A Max. passage width: 800 mm Max. passage height: 300 mm Transport speed: approx. 1.2 m/min at 50 Hz Working temperature: 110–250 °C Suitable for film types up to 100 µm External dimensions L × W × H: approx. 6,900 × 1,600 × 1,800 mm Total weight in operating condition: approx. 1,200 kg Sound emission: ≤ 75 dB(A) Equipment / Functions Hot air circulation Adjustable tunnel transport Temperature control Adjustable side air flaps Adjustable bottom air flow Heating fan Cooling fan Electronic preset counter Emergency stop device Cooling automatic Clean and clearly structured control cabinet Pjdjzwk T Tepfx Ab Tegu Original operating manual available Condition The system is in perfect technical condition and is also visually in very good and well-maintained condition. With only approximately 627 operating hours, the machine has very low operating hours. Price €17,000 (negotiable) Inspection possible by arrangement. Further information and pictures available upon request. Subject to prior sale and errors.

Condition: like new (used), Year of construction: 2025, functionality: fully functional, warranty duration: 6 months, Automatic folding machine with vacuum air feeder Pedpfx Aozvpwzsb Tsgu Pocket adjustment via touch screen display Working width 139 – 320 mm Folding length in pocket 1/2 338/226 mm Paper format max. 674 x 365 mm (L x W) Paper format min. 140 x 160 mm (L x W) Smallest folding length 46 mm Paper weight max. 240 g/m² Paper weight min. 56 g/m² Paper weight max. approx. 400 g/m² Loading capacity 500 sheets A4/80 g/m² Length of the delivery table 645 mm Preset counter: yes Total counter: yes Digital display: yes With perforating unit

Condition: ready for operation (used), Year of construction: 2022, spindle speed (max.): 5,000 rpm, spindle motor power: 15,000 W, number of axes: 2, Horizontal turning machine manufactured in 2022. This Okuma GENOS L2000-e features a maximum turning diameter of 220 mm and a turning length of 500 mm. It is equipped with a spindle power of 15 kW and a spindle speed of 5,000 rpm. If you are looking to get high-quality turning capabilities, consider the Okuma GENOS L2000-e machine we have for sale. Contact us for further details. • Spindle: ASA6 mount, 52 mm bar capacity • Chuck: 8" self-centering • Max turning diameter: 220 mm • Swing diameter: 450 mm • Max turning length: 500 mm • Tailstock: Automatic cycle with MT5 rotating center, 5 kN thrust • Software/features: Tool life management; automatic chuck open/close and tailstock advance/retraction during rotation; CNC cutting force monitoring (OSP P300LA-e TEX Kit for X/Z and spindle); IGF Advanced (L) with 3D real simulation; API Library 2 (ON STATUS) • Thermal deformation control: TAS-C (Thermo Active Stabilizer - Construction) Pedpo Adp U Hjfx Ab Tjgu • Usage/condition: Very little used (about 8 months of operation) Additional equipment • Chip conveyor: hinge type • High-pressure coolant pump: 0.8 kW, 5 bar, 20 l/min • Parts unloader: parts catcher arm and unloading (applicable with manual preset) • Bar feeder interface: prepared for bar feeder • Tool setter: manual presetting • Tool holder kit: 4 external, 1 front, 3 boring bar holders, 8 bushings, 3 plugs Technical Specification Counter Spindle Yes Driven Tools No

Condition: ready for operation (used), Year of construction: 2022, operating hours: 347 h, spindle speed (max.): 3,800 rpm, travel distance X-axis: 235 mm, travel distance Z-axis: 520 mm, spindle motor power: 22,000 W, overall weight: 4,600 kg, number of slots in tool magazine: 12, number of axes: 3, This 3-axis Okuma GENOS L3000-e (Mx450) was manufactured in 2022. It features a powerful 22 kW main spindle motor with a maximum speed of 3,800 rpm. The machine includes a V12 radial turret for milling, a chip conveyor, and a touch setter for tool presetting. If you are looking to get high-quality turning capabilities, consider the Okuma GENOS L3000-e (Mx450) horizontal turning machine we have for sale. Contact us for further details. - Operating Hours: 521 hours- Spindle Running Time: 347 hours- Control Unit: OSP-P300LA-e / OSP P300L-R-TD Kit- Main Spindle Motor Power: 22 kW- Main Spindle Speed: 3,800 rpm- Chuck: 10" Hollow clamping chuck (250 mm) Type N210A8- Spindle Bore: 80 mm- Spindle Nose: A8- Turning Diameter (VDI Turret): 300 mm- Max. Turning Length (VDI Turret): 450 mm- X-Axis Travel: 235 mm- Z-Axis Travel: 520 mm- C-Axis Range: 360° (0.001° resolution)- Rapid Feedrate (X / Z): 25,000 / 30,000 mm/min- Tool Turret: V12 Radial Turret with driven tool stations (VDI40)- Turret Stations: 12 (all 12 can be driven)- Driven Tools Power / Torque / Speed: 7 kW / 23.7 Nm / 4,500 rpm- Tailstock: NC Tailstock (MT5 taper, 5.0 kN thrust force)- Supply Voltage: 400 V- Phase: 3 P- Frequency: 50/60 Hz- Rated Capacity: 28.6 kVA- Full Load Current: 41.2 A- Largest Motor Rating: 96 A- Short Circuit Ratings: 2.5 kA- Machine Dimensions (without chip conveyor): 2,545 mm x 1,870 mm x 2,057 mm- Optional Equipment & Components: * V12 radial turret for milling function * Chip conveyor with side discharge * Grundfos high-pressure pump (0.8 kW) * Touch Setter M (Tool presetter) * Tool carrier VDI40 * Real 3D graphics simulation & One Touch IGF dialog programming * 1 set of soft jaws & 1 set of hard jaws * 3 pcs. Boring bar holders * 3 pcs. External turning holders * 2 pcs. Face turning holders * 8 pcs. Reduction sleeves (2x 16, 20, 25, 32 mm) * 1 pc. Reduction sleeve MK02 * Parts catcher (max. material dim. D51mm x 150mm, max. weight 2.3kg) * Bar feeder interface * Grippex bar gripper (40mm shank diameter, gripping range 3-60mm) * Hand wash gun set (incl. pump, spiral hose, switch) * Transformer Technical Specification Counter Spindle No Pjdpfx Abj Aa Aufo Tsgu Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, The Superfax PF215 letter folding machine, with its easy-to-read display, automatic feeder, and large 500-sheet stacker, is ideal for offices, print shops, mailrooms, and schools. It can handle paper up to A3 size and offers a wide range of folding options, including single fold, letter fold, zig-zag fold, gatefold, double parallel fold, and cross fold, with the ability to create custom folds. It even features micro-adjustment and skew adjustment for perfect folding results. It can process up to 8000 sheets per hour and delivers them onto its exit conveyor. SPECIFICATIONS Suitable for: Mailroom, Print shop, School, Larger office Pedpfxszz N Epo Ab Togu Paper Size: A3 / A4 / A5 Paper Weight: 45 - 105 gsm Fold Types: Z, Letter, Half, Double Parallel, Engineering, and Custom Folds Cross Fold: Yes Sheets Per Minute: 133 Sheets Per Hour: 7980 Feed Tray Capacity: 500 Speed Controller: Variable Piece Counter: Counter with Preset Functions Feed Type: Friction Hand or Automatic Feed: Automatic Feed Tires: 3 x 14mm Multiple Sheets (AKA Manual Bypass): No Conveyor for Exiting Paper: Yes Auto Shut Off: Yes Jam Detect: Yes Reload Whilst Running: No Dimensions W x D x H (mm): 939 x 482 x 558 Weight (Kg): 32

Condition: good (used), Display, display module, display panel, multifunction counter, controller, bidirectional counter, preset counter, digital counter Podpfxoyxbq Us Ab Tegu -Manufacturer: IVO, Multifunction Digital Counter with 6-digit LED Display -Type: N 214.002AX01 -Item No.: 300949 -Dimensions: 130/110/H50 mm -Weight: 0.4 kg

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, turning length: 111,111 mm, We offer you the following: Manufacturer: DMG MORI Model: NTX 3000/1500 Year of manufacture: 2023 Control: DMG Mori Celos with Fanuc F31iB5 Technical specifications: Max. turning diameter: 670 mm Turning length: 1,519 mm Bar capacity: max. 102 mm Travels: x1-axis: 675 mm y-axis: +/- 150 mm z1-axis: 1,562 + 164 mm b-axis: +/- 120° a-axis: 1,542 mm x2-axis: 200 mm y2-axis: +/- 40 mm z2-axis: 1,542 mm Main spindle: Max. speed: 3,000 rpm Drive power: 30/25 kW Torque: 1,194/995 Nm Spindle nose: JIS A2-8 Spindle bore: Ø 111 mm Counter spindle: Max. speed: 4,000 rpm Drive power: 18.5/18.5/15 kW Torque: 599/505/409 Nm Spindle nose: JIS A2-8 Spindle bore: Ø 91 mm Milling spindle: Speed range: 0 – 12,000 rpm Drive power: 28/23 kW Torque: 132/95.3 Nm Tool holder: Capto C6 Number of tool stations: 76 positions Max. tool diameter: Ø 70/Ø 130 mm Max. tool length: 400 mm Pedpfjy Sfx Nex Ab Tsgu Max. tool weight: 8 kg Turret: Number of tool holders: 12 positions Speed of driven tools: 12,000 rpm Tool holder: BMT40 Torque: 16.9 Nm Rapid traverse speeds: x-axis: 50 m/min y-axis: 40 m/min z-axis: 50 m/min a-axis: 36 m/min x2-axis: 25 m/min y2-axis: 18 m/min z2-axis: 40 m/min b-axis: 100 rpm Operating hours: approx. 4,500 h Spindle hours: approx. 2,200 h Technical features & accessories: − Hydraulic 3-jaw chuck, manuf. SMW KNCS-N-400-128 incl. hollow clamping cylinder for main spindle − Hydraulic 3-jaw chuck, manuf. SMW KNCS-N-260-78-3Z incl. hollow clamping cylinder for counter spindle − Foot switch for chuck operation − Automatic clamping stroke monitoring of the clamping cylinder for main and counter spindle − Tailstock function for counter spindle − Magazine-side control panel for the tool magazine − Coolant: water-soluble coolant − Chip conveyor (right discharge) − Coolant temperature control/coolant chiller − Coolant spray gun − Float switch for coolant − Coolant shower at main and counter spindle chucks − Compressed air blow-off system for chuck (counter spindle) − Oil mist separator zeroGOF #2 − Oil separator − ICS 70 bar, TMF300 band filter system, 980 l tank − Manual tool presetting device for main and counter spindle − Direct measuring system in x1, x2, y, z1, z2 axes − Spindle sensor measuring system with wireless signal transmission, manuf. Renishaw RMP600 − Universal filter − 3D quickSET − Cycle Alternating Spindle Speed − Cycle "Tailstock Tip at Turret" − Cycle MPC – Machine Protection Control − Cycle MVC – Machine Vibration Control − Synchronous thread cutting without compensating chuck − Increased input resolution to 0.0001 mm − Cs control for tool spindle − Program restart Accessories, illustrated tools, and clamping devices are only included if specified in the additional information. Technical data and details subject to change, errors and prior sale excepted!

Year of construction: 2004, condition: used, Year: 2004 Condition: good Counter. 91 Mil Impression but reality is approx. 200 Mil Machine on stock Configuration: - KOMORI LITHRONE 540 SP TYPE B - 10 colors offest press machine. Technical specification: - Maximum sheet size: 720 × 1,030 mm - Minimum sheet size: 360 × 520 mm - Paper thickness: 0.07 – 0.30 mm - Maximum printing area: 705 × 1,020 mm - Maximum printing speed: 13,000 sheets per hour - Minimum printing speed: 3,500 sheets per hour Printing plate: - Length × Width: 800 × 1,030 mm - Thickness: 0.30 mm Blanket: - Length × Width: 900 × 1,040 mm Inking unit: - Number of form rollers: 4 - Form roller diameters: 87.5 – 77.5 – 85 – 90 mm - Number of rollers: 21 (lower unit) / 20 (upper unit) Pile height: - Feeder: 1,430 mm - Delivery: 1,430 mm Dimensions and weight: - Length × Width × Height: 11,022 × 4,037 × 3,383 mm - Weight (standard configuration): 64,220 kg (machine only) Electrical specification: - Power consumption: 117.94 kW (machine only) - Frequency: 50 Hz Pedpoy Ixnpefx Ab Togu Specification: - Remote diagonal register adjustment (cocking). - Semi-automatic plate changing in the upper printing unit. - Semi-automatic plate changing in the lower printing unit. - AMR job presetting system: presetting of paper size and thickness, presetting of feeder table brushes / feed roller, presetting of feeder side air blowers, presetting of the side lay, and sheet drum brake position. - Automatic ink roller washing system. - Automatic blanket washing system. - Automatic impression cylinder washing system. - Lateral feeder pile adjustment (via shifting feeder). - Remote sucker height adjustment. - Water-cooled distributor rollers. - Oscillating ink form rollers: 2 × B and 2 × D for the upper and lower printing units separately. - Chrome-plated plate cylinder. - Chrome-plated impression cylinder (with special surface coating). - Chrome-plated blanket cylinder. - Combined Technotrans Beta.C 300L system for dampening solution cooling and ink temperature control (including CombiControl 4.3, Aquados C5, and integrated tank). - Grafix powder spray unit with Grafix powder spraying system.

Condition: used, Year of construction: 2006, Masterfill Filling Machine S 500 The Masterfill S 500 is a high-performance, precision filling machine designed to meet the demanding requirements of modern dairy and food production facilities. Built for reliability, efficiency, and hygiene, the S 500 delivers consistent filling accuracy across a wide range of liquid and semi-liquid products. Engineered with advanced control systems, the S 500 ensures smooth operation and minimal product waste, making it ideal for filling milk, yogurt, cream, sauces, and other viscous products. Its robust stainless-steel construction guarantees durability while complying with strict food safety and hygiene standards. Pgsdpfx Ajywuczsb Teu The machine features user-friendly controls, allowing operators to easily adjust filling volumes and production speeds to suit different product types and packaging formats. With its compact footprint and efficient design, the Masterfill S 500 integrates seamlessly into existing production lines. Key Features - High-precision volumetric filling system - Suitable for liquid and semi-viscous products - Hygienic stainless-steel construction - Easy-to-use control interface - Adjustable filling speed and volume - Low maintenance and easy cleaning - Compact and space-efficient design Applications - Milk and dairy products - Yogurt and desserts - Cream and sauces - Beverage and liquid food products Materfill S500 6 head fill while rise filler M2-AF Serial number 4716 YOM 2006 Filling capacity 2ml to 2000 ml The filler is a 6 head automatic filler, with the capacity to store 50 separate preset menus, Brief FDS • Controlled by Siemens S7 PLC via Mitsubishi Beijer HMI • Jars feed in vis constant stainless steel slat band • Jars indexed via program-controlled infeed and outfeed pneumatic gates. • Jars filled via positive pressure within 50 ltr holding tank (this could be changed easily to a constant positive pressure into manifold via modulating pump) • Volume controlled via Nixon BNO turbine flow meters communications with siemens high speed counter. • Liquid feeds into jar with rise during fill or above jar for fill time • Full SIP, CIP, and flush capability programs available Dico CapperSerial number 3/379Brief FDS  Capper with rotating starwheel  Will cap Square of round Jar/ Bottles (change parts included)  Jar enters, signals PEC starwheel turns 90⁰ under capping head  Capping lowers on cam, retracts on cam  Jar/ bottle clamp activated of adjustable cam onto 5/2 valve  Starwheel turns 90⁰ onto exit conveyor  Current capping head removable, for 40mm cap (no alternative head)  All systems work on cams and relays, no PLC  Motor runs on DOL for capping (clutch adjusted and variable speed gearbox)  Cam motor uses inverter. Guards with interlocked access doorway Required services.  3 Phase 32-amp electrical supply  7 Bar air pressure Main control panel Cap sorter and feederRNASRC-N 400-2LSerial no 00801Brief FDS  40mm cap sorter and feeder  Vibrating bowl agitates caps upwards  Air jets and cut outs sort caps placing in correct orientation  Cap chute allows smooth passage to dispensing head with some adjustment  Cap dispenser works on bottle/jar passing under and catching cap, this allows the retaining jaws to open and release cap  Side or over independent speed controlled wheel assists in cap leveling Required services.  240V electrical supply  3 Bar air pressure Filling volume: 25-2000 ml Controls: SIEMENS S7 via Mitsubishi H...

Condition: used, Year of construction: 1982, cutting diameter 200 mm band length 350 mm capacity 90 degrees: round 200 mm total power requirement 3,0 kW weight of the machine ca. 0,45 t dimensions 1,4 x 1,4 x 1,3 m Automatic hacksaw - with 1000 mm infeed roller conveyor - preset counter Pgsdpfx Aey N D H Hsb Tju - material stop with trigger, max. 600 mm - coolant system

Condition: used, Electric hot air steamer with direct steam   Hot air steamer – operating principle Cooking mode AC (Automatic Cooking): Automatic cooking system for recipes from all over the world, featuring a photo presenting the dish. Pgodev Hztaepfx Ab Tsu Manual cooking with three cooking modes: convection from 30°C to 300°C, steam cooking from 30°C to 130°C, and a combination of hot air and steam from 30°C to 300°C. Programmable operating mode: Cooking processes can be programmed and stored in an automatic sequence (up to 15 cycles). Each program can be assigned a unique name, as well as images and information about the recipe. Clima® - Automatic measuring and control system for the percentage of humidity in the cooking chamber. Fast-Dry® - System for rapid dehumidification of the cooking chamber.   Operating principle Configurable display as needed, with the most frequently used programs brought to the foreground. Automatic start of the cooking process (AC) with "One Touch". Arrangement of recipes in folders with a preview and a unique name for each folder. Intelligent recognition of recipes in folders with subfolders. Capacitive 7" LCD TFT color screen with high resolution and touchscreen function. Scroll wheel plus with scroll function and push function to confirm the selection made.   Equipment for control and operation Autoreverse function (automatic reversal of the fan's direction of rotation) for uniform cooking. Delta T system for the parallel control of the temperature in the cooking chamber and inside the product. Automatic regulation of steam condensation. Easy access to programmable user parameters to make personal adjustments on the device via the menu. Delayed start of the cooking process, programmable. Option to choose from up to 6 ventilation speeds, with the heating output automatically reduced for the first 3 speeds. For special cooking processes, the speed can be changed alternately. The temperature inside the product is monitored via a four-point core temperature sensor. External interface for easy and quick connection of the core temperature sensor to the cooking chamber. USB port for downloading HACCP data, updating software and downloading and uploading cooking programs. Preset system to optimize energy consumption (optional). Service program: checks the functions - control board and displays the core temperature sensor - operating hour counter of the main functions for scheduled maintenance. Self-diagnosis and check of the device's functionality before each use, with written and audible indication of any abnormalities. LED lighting of the chamber. Ecospeed - Depending on the quantity and type of product, the device controls and optimizes energy consumption, while always maintaining the correct cooking temperature and avoiding fluctuations. Ecovapor - With the Ecovapor system, water and energy consumption are significantly reduced thanks to the automatic control of the steam saturation in the cooking chamber.   Cleaning / Maintenance Automatic cleaning system LCS (Liquid Clean System) with integrated tank and automatic dosing (cleaning liquid Combiclean in 100% recyclable capsules. Included is 1 cartridge container of liquid detergent CDL05 - 990 g). 7 automatic cleaning programs. Manual cleaning system with an external hand spray.

Condition: ready for operation (used), Year of construction: 2011, operating hours: 8,733 h, functionality: fully functional, spindle bore: 26 mm, rotational speed (max.): 7,200 rpm, number of axes: 5, number of tool turrets: 2, Long-turn lathe with an extended accessory package and spare parts! Psdpeztn Imsfx Ab Tjgu Counter-spindle: Completely re-conditioned 05/2026 TECHNICAL DETAILS CNC control: GE Fanuc Series 18i-TB Number of axes: 5 Axes: X1, X2, Y, Z, C Spindle Spindle speed: 50–7,200 rpm Spindle bore: 26 mm Spindle stroke: 160 mm TURRET Number of turrets: 2 Positions per turret: 6 MACHINE DETAILS Motor power: 3.7 kW Weight: 2,600 kg Spindle hours: 8,733 h Control on: 10,642 h Feed time: 3,257 h Part counter: 478,135 EQUIPMENT - Bar feeder FMB Turbo 3-36, year of manufacture 2011 - Chip conveyor - Package of fixed and powered tool holders - Package of collets and guide bushings - Discharge system for long parts including reduction sleeves - Double-cone clamping system on the main spindle, system JBS - Breakage detection for cut-off tools, Detector France - Ejection control, Detector France - JBS guide bushing, not yet installed - Tool presetting device with optics for external tool setup - Replacement worms for chip conveyor - Mounting device for adjusting the cylinder of the working hood - Various spare parts

Condition: used, Year of construction: 2007, pressure 200 t throat 510 mm stroke 16 - 160 mm ram - range of adjustment 120 mm table surface area 1500 x 1000 mm table height over floor 900 mm hole in the table 800 x 250 mm ram surface 1000 x 700 mm tool hole in ram 65 x 110 mm T-slot - width 28 mm number of strokes adjustable 30 - 120 min oil volume Hydraulikaggregat 5 l daylight, max. stroke above - ram adjustment above 600 mm daylight (stroke down, ram adjustment above) 440 mm total power requirement 32,2 kW weight of the machine ca. 24 t dimensions of the machine ca. BxTxH 2,85 x 3,1 x 3,65 m - hydraulic clutch - fixed table - hydraulic overload protection in the ram - hydraulic connecting rod clamping - Motorized ram height adjustment 120 mm with digital display set ram height, rapid and slow speed - fully automatic stroke adjustment, adjustment range 16 - 160 mm - Ram weight compensation - electronic OT correction - Planetary gears - Oil circulation central lubrication - Separate control panel with SIMATIC S7/300 screen control - Press force measuring device - Reversing switch (return) - additional operating mode “set-up-creep speed” - electric stroke counter Pgjdpfx Ajvbk Rwsb Teu - electrical preset counter - electrical travel limitation of the connecting rod journal - electronic cam switch - continuously variable drive (frequency controlled) - 2 sockets - Clamping plate - Temperature monitoring main bearing / support bearing / connecting rod bearing - Operating hours counter - Oil cooler - Set of oscillating elements Additional equipment: Electronic roller feed ebu EVX 500 Passage width: 10 - 500 mm Material cross section: max. 1,600 mm² Material thickness: 0.2 - 5.0 mm Number of reels: 2 Roller diameter: 100 mm Intermediate ventilation: up to over 300 l/min Feed length: 1.0 - 9,999.9 mm Feed speed: max. 150 m/min

Condition: used, Year of construction: 2007, Prominent water treatment plant, consisting of: 1. Softening: The raw water is fed into the double softener. Only one bottle is ever in operation and the other is in regeneration or stand-by. In the softener, calcium and magnesium are replaced by sodium. The system has a volume counter that switches to the other bottle when the preset quantity is reached. Regeneration takes place with saline solution from the brine tank. The value at the outlet is 0°dH. 2. reverse osmosis: Reverse osmosis fills the permeate tank with demineralised water, so-called permeate. Depending on the raw water quality, water temperature, condition of the membrane and correct setting, different conductance values and operating pressures result. The following flow rates are set during commissioning: Permeate 600 l/h, concentrate 200 l/h, corresponding to a yield of 75%. 3. permeate tank and ozonisation: The unpressurised 500 l permeate tank has an adjustable level control. For treatment with ozone, the water in the permeate tank is circulated via an adjustable ozone feed point. The ozone is generated from air in the ozone generation system by means of a silent electrical discharge and is available as an ozone-air mixture. The air and the undissolved ozone rise upwards in the permeate tank and are discharged via the residual ozone destroyer. A redox potential and ozone measurement is carried out after the centrifugal pump for monitoring purposes. The ozone dosage is set via the touch panel. You can choose between regulation via the redox potential or the ozone concentration. Additional title: Water softening, reverse osmosis system, ozone sterilisation Permeate output: 600 l/h Concentrate output: 200 l/h Ozone output: 5 g/h Max. working pressure: 16 bar Current: 2 A Voltage: 230 V Frequency: 50 Hz Pgsdpfx Abow Uvdge Tou Water: < 5 bar (cooling water) Compressed air: 5,5 - 6,5 bar (max. 10 bar); max. 0,37 Nm³/h Operation / Control: Simatic S7-300, Touch Panel Position: free standing Base construction: Fully mounted on tubular frame with spherical feet Features: Reverse osmosis unit, reaction tank complete with residual ozone destroyer, ozone generator, ozone gas warning device, ozone and redox sensor, switch cabinets with control unit

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S23NEOS21, Exhibition unit ATLANTA NEOS stretch wrapper with articulated arm 99 individually storable programs Start/stop at the same position (corner counter) Wrapping height 2000 mm Mast height approx. 1500 mm (fits through almost any door and in almost any van) Powerstretch PRS 200% film (more available as an option) Motorized pre-stretch system with stepless adjustment Electronically controlled film tension via control unit IEF quick-loading system for easy film roll changes Film specifications: Max. outer diameter Ø300 mm – height = 500 mm – core Ø76 mm Automatic film cutting unit (available as an option) Film tension storable in 4 steps TECHNICAL DETAILS: Two maintenance-free 12 V – 100 Ah AGM batteries connected in series Minimum 160 pallets per Charging – Charging time: 8-10 hours High-frequency battery charger with LED display Wrapping height “Machine with MAST (pallet included) 2,150 mm Height measurement via light sensor or dimension input on the display Pgjdsz Iq Trjpfx Ab Teu Protective bar for emergency stop of the drive Emergency stop switch compliant with CE regulations Acoustic warning signal and warning light at machine start Fall protection for the film carriage Push buttons for start & stop Machine function compliant with CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters adjustable via display - Display lock for program changes - Adjustable machine speed around the pallet up to 80 m/min Upward and downward carriage speeds independently adjustable - Upward carriage speed from 1.3 to 5.4 m/min - Downward carriage speed from 1.3 to 5.4 m/min - Number of wraps at the pallet base (1-10 wraps) - Number of wraps at the pallet head (1-10 wraps) - Pallet wrapping height adjustment - Film application tension for foot and head wrapping / ascending and descending, independently adjustable - Film pre-stretch for foot and head wrapping / ascending and descending, independently adjustable - Ergonomic height for film changes ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 99 storable wrapping programs for the NEOS arm - Cross wrapping (upward/downward) - Simple wrapping (upward only or downward only) - Wrapping cycle with preset start and stop height - Wrapping to a preset height (with the height sensor deactivated) - Wrapping cycle for large pallets - Wrapping cycle for top sheet film - Soft start cycle for applying edge protection - Wrapping cycle with reinforcement and adjustable number of wraps Soft start to reduce film tears on sharp edges Pallet edge wrapping Wrapping cycle with manual or motorized cord formation (optional) Further systems available immediately from our Ludwigsburg warehouse Also available with the ARYA system – automatic film application possible

Condition: ready for operation (used), Year of construction: 2006, operating hours: 16,093 h, functionality: fully functional, turning length: 1,000 mm, spindle speed (max.): 5,000 rpm, controller model: MITSUBISHI M-720BM (MAPPS 2), counter spindle speed (max.): 5,000 rpm, milling spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Turning length: 1,000 mm Pedey Eydyepfx Ab Tsgu Main Spindle Max. spindle speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: 73 mm Counter Spindle Max. spindle speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: 73 mm Milling spindle speed: 0 - 12,000 rpm Tool holder: Capto C6 Tool stations: 100 positions Hollow clamping device: 67 mm MACHINE DETAILS Control unit: MITSUBISHI M-720BM (MAPPS 2) Operating Hours Operating hours: 26,875 h Spindle hours: 16,093 h EQUIPMENT Y-axis Fully indexable B-axis Chip conveyor, discharge right Standard coolant system Interface for high-pressure coolant system, 70 bar Tool spindle with through-spindle cooling Coolant spray gun Blow air through sub spindle Manual tool presetting on main spindle 3-color signal tower Double foot switch Simultaneous 5-axis machining Automatic power off Tool offset for 5-axis machining Programmable data input Dynamic interchange diameter/radius Stroke check prior to movement

Condition: ready for operation (used), Year of construction: 2013, spindle speed (max.): 6,000 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 550 mm, spindle motor power: 11,000 W, controller manufacturer: OKUMA, number of axes: 5, This 5-axis Okuma LB2000EX II was manufactured in 2013. It features a maximum turning diameter of 360 mm and a turning length of 500 mm. The machine includes a robust turret with 12 stations and a main spindle speed of 6,000 rpm. If you are looking to get high-quality turning capabilities, consider the Okuma LB2000EX II horizontal turning machine we have for sale. Contact us for further details. • Maximum turning diameter: 360 mm • Maximum turning length: 500 mm • Maximum bar capacity: 62 mm • W-axis travel: 500 mm • C-axis indexing: 0.001° • Main spindle nose: ASA 6" • Sub-spindle maximum speed: 6,000 rpm Pgjdezcphuopfx Ab Teu • Sub-spindle motor power: 11 / 7.5 kW • Turret stations: 12 • Driven tool speed range: 45–6,000 rpm • Driven tool motor power: 5.5 / 3.7 kW • Turning tool size: 20 × 20 mm • Boring bar capacity: Ø32 mm Additional equipment • Bar feeder: TOP XF365 (YOM 10/2013, installed 2014) • Hinge-type chip conveyor • Manual tool setter (presetting) • Parts catcher Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: used, Year of construction: 1983, workpiece diameter 250 mm centre distance 0 mm honing length max. mm max. module 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features * Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. * All roughing and finishing infeeds can be adjusted by a decade switch; as well as by table reverse times and fast infeeds with preset times (1sec = Ø 0.04 mm), set on a potentiometer. Ampere display, etc. * Convex honing and conical honing are possible via templates. Asymmetric honing is also possible if the workpiece is prepared appropriately (i.e. pre-shaped). * Separate honing oil unit with magnetic separator and fine filter. * Mechanical tailstocks for manual loading. * Oil mist separator. * Sliding doors with foot switch. * Separate hydraulic unit. Condition : Good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Pgjdpfx Aot Hwzpjb Tju We have a large selection of gear machines available. Please let us know your requirements.

Condition: used, Year of construction: 1981, cutting diameter 320 mm saw band length 4670 mm cutting width 580 mm total power requirement 7,4 kW weight of the machine ca. 3 t Sawing range, circular, max. 100 - 320 mm vertical, max. 100/100 x 320/460 mm Length of cut, min./max. 0 - 580 mm Distance from column to saw band, max. 690 mm Cutting speed, infinitely variable 16 - 160 m/min Dimensions of saw band, length x Ø approx. 4,670 x 38 mm Length of remaining pieces, automatic/single cut 100/10 mm Saw blade drive, approx. 4.4 kW Total electrical load, approx. 7.4 kW - 380 V - 50 Hz Weight, approx. 3,000 kg Accessories / Special Features: * Infinitely variable speeds of saw blade motor via servo motor and STOEBER drive. Display of cutting speed on control panel. * Infinitely variable settings of sawing feed with display of the current cutting speed. * Workpiece counter: Number of workpieces can be preset. Selection switch for single cuts / multiple cuts. Pgjdjt Hwrnepfx Ab Tju * Display for band tension and cutting feed. * Automatic motor-driven material feed, controlled by a positioning processor, Model PP 160, with input of the appropriate lengths using a roll conveyor approx. 1,500 mm, with enlargement approx. 2,000 mm. And with a stable roll conveyor for the exterior area, 3,500 mm. * Built-in chip conveyor with coolant device. * Built-on switch cabinet. Condition : Good. Machine can soon be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We have a selection of saws on stock. Please let us know your requirements.

Condition: ready for operation (used), Year of construction: 2014, functionality: fully functional, stack height: 60 mm, paper weight (min.): 40 g/m², paper weight (max.): 300 g/m², production capacity: 5,000 unit/h, Duplo Booklet Production System 5000 The offer includes: 1x Collating Tower DC-10/60 Transfer Unit LUL-HM Staple and Folding Unit DBM-500 Front Trimmer DBM-500T Preset Counter DBM-K Long Delivery Stacker DBM-400LS DC-10/60 (10 Stations) Paper size: min. 120 x 148 mm; max. 350 x 500 mm Paper weight: 40–300 gsm Stack height: 60 mm per station Feeders: Suction/blast air Controls: Double sheet, misfeed, paper jam, empty station detection Power supply: 230 V, 50 Hz, 4.5 A, 1,035 W Dimensions: 630 mm x 750 mm x 1,972 mm Pgodpfx Abjx Nimrj Tju Weight: 290 kg Folding and Stitching Unit DBM 500 Paper size: min. 120 x 170 mm; max. 350 x 500 mm Speed: 5,000 cycles/h (A5) 4,600 cycles/h (A4) 4,000 cycles/h (A3) Stapling capacity: 5 mm (50 sheets, 80 gsm) Folding capacity: 25 sheets Number of stitch heads: 2 Controls: Paper jam, paper position indicator, wire end Memory: 12 jobs Folding and stapling styles: folding without stapling; saddle stitching with folding; corner stapling with folding; corner stapling; block/side stapling Power supply: 230 V, 50 Hz, 5 A, 1,150 W Dimensions: 1,610 mm x 770 mm x 1,020 mm Weight: 412 kg Front Trimmer DBM 500T Booklet size: min. 85 x 120 mm; max. 250 x 356 mm Trimmed final size: min. 75 x 120 mm Speed: >5,000 cycles/h Processing capacity: 50 sheets (80 gsm) Power supply: 230 V, 50 Hz, 3.3 A, 759 W Dimensions: 700 mm x 635 mm x 1,094 mm Weight: 241 kg

Year of construction: 2000, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 68370, SMB Technik Multima 9R/9L/3K automatic beer bottling monobloc for rinsing, counter-pressure filling and crown capping of glass bottles. The machine was previously in operation at a Norwegian brewery. Following the sale and removal of the labelling machine, an electric motor is required to drive the bottling line. The electric motor is not included in the sale. The SMB rinsing, filling and capping monobloc was operational prior to this change and can be inspected at its current location in Norway. CONFIGURATION * 9-station bottle rinser * 9-head counter-pressure filler * 3-head crown capper * Automatic bottle transfer through rinsing, filling and capping sections * Conveyor sections * CO₂ counter-pressure / isobaric filling * Long-tube bottom-up filling * Separate bottle pressurising and return-gas system * Automatic filler bowl level and pressure control * High-pressure injection / jetter before capping * Electrically interlocked safety doors * Automatic bottle presence monitoring FILLING PROCESS The Multima is designed for bottling beer in glass bottles. Bottles are rinsed before being transferred to the filling section. Before filling, the bottles are pressurised, normally using CO₂. Beer is then filled from the bottom through long filling tubes. The system uses separate channels for bottle pressurising gas and return gas and is designed to minimise turbulence, foaming and oxygen uptake. After filling, the bottles pass a high-pressure injection device (jetter), which produces controlled foaming to help displace air from the bottle neck immediately before crown capping. TECHNICAL DATA Manufacturer: SMB Technik GmbH, Mannheim, Germany Model: Multima 9R/9L/3K Year: 2000 Serial number: 68370 Electrical supply: 400 V / 50 Hz Current: 12 A Container: Glass bottles Product: Beer Closure: Crown caps Filling principle: Counter-pressure / isobaric Rinser: 9 stations Filler: 9 filling valves Capper: 3 heads A 400 V to 230 V converter is included in the sale. DOCUMENTATION Psdpfxsz Dhrqs Ab Tsgu Extensive original SMB technical documentation is available, including operating instructions, setup and adjustment procedures, bottle changeover information, cleaning and sanitising procedures, maintenance and troubleshooting information, as well as filling-valve technical documentation. IMPORTANT The labelling machine has been sold separately and is NOT included. An electric motor is required to operate the bottling line and is NOT included. Tanks and other brewery equipment visible in the photographs are not included unless specifically agreed. The machine is located in Norway and can be inspected by appointment. Dismantling, loading and transport can be discussed separately.

Condition: used, mileage: 140,278 km, power: 96 kW (130.52 HP), first registration: 05/2019, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, total length: 7,030 mm, total width: 2,115 mm, total height: 3,065 mm, loading space length: 4,377 mm, loading space width: 2,044 mm, loading space height: 2,146 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, tail-lift, Errors and prior sale excepted! Internal number: 1082. 2K50928 ----EQUIPMENT * SCHUTZ vehicle body with box body * SÖRENSEN tail lift * Reverse camera * Seat belts: 3-point height-adjustable seat belts with pyrotechnic belt tensioners * ABS * Storage: - Storage compartment under driver’s seat (not with seat base cover) - Storage compartments in front doors - Recess above glove compartment - Storage compartments above ventilation outlets in the center dashboard - Removable container under passenger seat - Right lockable glove compartment (5.3 dm³) - Lockable center storage compartment (11.38 dm³) * Driver’s airbag * Interface box for body manufacturer * Exterior mirrors, incl. integrated side indicators and wide-angle inserts * Mechanical brake assist * Rev counter * Electronic Stability Program (ESP) incl. ASR with indicator - Hydraulic brake assist - Hill holder (automatic hold for hill starts) - Load Adaptive Control (adjusts ABS, ASR, and ESP functions to vehicle load) * Power windows front, with comfort function for driver’s side * Transmission: 6-speed manual Psdpfsyht H Esx Ab Tjgu * Headrests (3) * Paint: solid color * Steering wheel with reach adjustment * Manual headlight leveling * Multifunction display with clock, warnings for headlights on and preset speed limit exceeded, and onboard computer * Particulate filter: diesel soot filter * Upholstery: fabric * Radio pre-wiring (cables and antenna) * Black side protection strips * Power steering * Seats: passenger double bench seat with folding table in center backrest * Seats: driver’s seat with longitudinal, height and backrest adjustment, armrest, and lumbar support * 12V socket in center console * Service interval display * Immobilizer with transponder * Central locking with high-frequency remote control ... and much more. ----The vehicle is in unprepared condition! Nationwide delivery available for an additional charge. Errors and prior sale excepted. We are happy to accept your vehicle as trade-in. Financing / Leasing possible even without down payment! Do you have any questions? We are happy to advise you!

Year of construction: 2019, condition: used, functionality: fully functional, machine/vehicle number: 460923-80034645-001, This is an under-counter refrigeration unit from the manufacturer NordCap, which is perfectly suited for installation under existing cooking ranges or grill stations. The unit was manufactured by the premium manufacturer Ideal. The under-counter refrigeration unit features a built-in stainless steel evaporator and is equipped with 4 full-extension drawers. The usable height is 90 mm per drawer. Two identical units are available for sale. The unit has been inspected in our in-house workshop and is fully functional. The unit was only used for 6 months and was stored due to the business closure. Condition: very good (used). The list price is €5,500 net. You will receive an invoice with VAT shown. Our used equipment service for you: * 6 months warranty on all electrical parts, limited to the replacement of defective parts, excluding installation and removal costs * High-quality brand-name equipment at fair prices * Professional overhaul/inspection & expert cleaning * Inspected & fully functional - or money back * Shipping or self-collection can be flexibly selected * Competent advice - before and after purchase * Provision of operating instructions, connection diagrams & spare parts * Inspection according to DGUV V3 Technical data: * W x D x H: approx. 1380 x 660 x 410 mm * Power connection: V: 230 / kW: 0.265 * Serial number: 460923-80034645-001 * Year of manufacture: 2019 Pgodpfx Ajzu Sapeb Tou Condition: used, inspected, fully functional Shipping: * Delivery or self-collection by arrangement * Worldwide shipping on request * Shipping to islands or mountain stations only by arrangement Do you have any questions, would you like to receive advice or would you like to see something on site? You can reach us by telephone during our opening hours: Monday to Friday from 9:00 a.m. to 1:00 p.m. and from 2:00 p.m. to 5:00 p.m. Subject to changes and errors. The sale is exclusively subject to our general terms and conditions (GTC), which can be found under the link "Legal Information".

Condition: good (used), Year of construction: 2016, operating hours: 17,000 h, functionality: fully functional, FOR SALE 5-Axis Machining Center – DMG MORI DMU 95 monoBLOCK® YEAR 2016 Description: Selling a DMG MORI vertical 5-axis simultaneous machining center (Deckel Maho Pfronten GmbH), year 2015. A versatile, highly rigid, and well-equipped professional machine. Suitable for complex and high-precision machining operations. Can be viewed powered on and in operation on site. Main Features: • Numerical Control: HEIDENHAIN TNC 640 (ERGOline® interface) • Spindle speed max: 20,000 rpm • Hour counters: Power on: 48,878 h | Actual machining: 17,030 h • Machine weight: ~14,000 kg (14 tons) Capabilities & Machining Envelope: • Travels: X = 950 mm | Y = 850 mm | Z = 650 mm • Max. workpiece dimensions: Ø 1,040 mm x Height 590 mm • Tilting rotary table: Ø 850 x 750 mm (Max. load 1,000 kg) • Tool magazine: 60 positions Equipment & Included Options: • HEIDENHAIN TS 649 infrared workpiece probe • BLUM laser tool measurement system • quickSET 3D geometric control kit • Remote electronic handwheel • Nozzle ring for coolant around the spindle • Safe operating mode: Mode 4 • Automatic chip conveyor & Original transformer • 3D STEP digital model of the machine included (for simulation/CAM) Conditions: • Removal, lifting, and transport are the sole responsibility of the buyer. Pgedpfx Abo Af Aias Tsu PRICE €173,000

Year of construction: 2024, condition: like new (used), functionality: fully functional, Sure. Below is a technical and commercial description suitable for product presentations, catalogs, or proposals: ### Mertmakina Mattress Packaging Machine with Integrated Quality Control System The Mertmakina mattress packaging machine is an industrial solution designed to automate and optimize the mattress packaging process, ensuring speed, uniformity, and quality in the final product packaging. Pgodpfxoz Dk Arj Ab Tou The equipment integrates a quality control system, allowing for the monitoring of key stages in the packaging process and the identification of potential anomalies before the product leaves the line. #### Key Features * Automatic mattress feeding and positioning, ensuring a continuous and regular process. * Automatic packaging system, adapted to the dimensions and characteristics of different mattress models. * Control of the application and sealing of the packaging, ensuring a uniform and consistent finish. * Integrated quality control system, designed to verify process parameters such as positioning, packaging integrity, and proper sealing. * Error and anomaly detection, with the possibility of signaling or automatic rejection of units that do not meet the defined parameters. * Intuitive operating interface, allowing the operator to monitor the machine's status, adjust parameters, and consult process information. * Recording and monitoring of production and control data, contributing to traceability and continuous improvement of production. * Robust industrial construction, suitable for operation in continuous production environments. * Increased productivity and reduced manual intervention, while simultaneously reducing variability between packages. ### Integrated Quality Control The integration of quality control transforms the machine into a more complete production and inspection system. Each mattress can be monitored during the process, allowing verification of whether the packaging has been correctly applied and whether the product meets the previously defined parameters. When a condition outside the established limits is detected, the system can generate an alert for the operator and, depending on the installed configuration, automatically direct the product for inspection or rejection. In this way, the solution helps to reduce packaging errors, increase the consistency of the final product, improve traceability, and reduce waste. ### Result The Mertmakina mattress packaging machine, equipped with an integrated quality control system, provides a solution focused on automation, productivity, standardization, and process control, enabling companies to increase the efficiency of the production line and ensure a consistent final presentation of the mattresses.