Used Preset for sale (287)

Condition: used, Autotherm Type: Autotherm temperature control unit AWF 130-27/VK/6K 6-circuit temperature control unit Without active refrigeration unit! According to the enclosed technical brief: Temperature range: -40°C ... +85°C (extended temperature range -40°C…+130°C) Increased heating capacity: 27 kW instead of 18 kW Includes 1x temperature control in the main circuit Includes 6x temperature measurement in each supply line Includes 6x temperature measurement in each return line Includes 6x flow rate and pressure measurement in each supply line Includes 6x flow rate and pressure control 1 l/min .. 12 l/min and 0.1 bar … 3 bar Including changeover control Including frequency inverter-controlled pump in the main circuit Including 6x 3-way valve Includes 6x additional relief valve 2 … 12 bar, adjustable Preset to 2.4 bar Includes filling and draining device For all circuits, jointly/simultaneously Including 50-liter integrated tank Including pneumatic drain function Including S7 control system Energy saving and increased cooling capacity: An additional glycol circuit integrated into the temperature control circuit takes over the cooling of the consumer in a temperature range of +85°C to +30°C. The absorbed energy is transferred to the on-site < 20°C chilled water network. The cooling capacity at a supply temperature of +20°C is: 50 kW. This increases the cooling speed in this temperature range and saves energy due to the shorter running time of the refrigerant compressor. (The footprint of the base unit increases by approx. 0.3 m² according to the data sheet). Assembly in Rittal modular enclosure: 2x TS8 800x1000x2000 mm 1x additional, separate enclosure, min. 600x600x2000 mm (for control/electrical components) Supplied via on-site or optional cooling medium supply. Supply temperature, on-site cooling fluid -43°C, cooling fluid requirement 7.5 m³/h, continuously regulated. For cooling capacity, a cooling medium must be connected! Weight approx. 1200 kg Sold ex-works! Condition: used Fodpfxezd Rtyo Abajgi Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: good (used), Manufacturer: SOMET Type: SDJ 300 Measurable tool diameter: Ø 6 - 300 mm Measurable tool length: 40 - 500 mm Accuracy: 0.002 mm 1x interchangeable collet ISO 40 1x interchangeable collet ISO 45 1x interchangeable collet ISO 50 1x test mandrel ISO 50 Used! Dimensions: 1250 x 600 x 1870 mm Fsdjd N S Ubopfx Abaogi

Condition: like new (used), functionality: fully functional, Year of construction: 2026, - Automatic hot mounting press - Product details: - corrosion-resistant table model with automatic hydraulic hot mounting - electro-hydraulic automatic system - 7-inch user-friendly LCD touchscreen system - Preset programming and data storage parameters (up to 100 memory locations) - Setting of heating time, cooling time, assembly temperature, pressure build-up and cycle start via the LCD touchscreen - Cooling process - slow cooling, medium cooling and fast cooling mechanism. - Easy replacement of the mold assemblies - Sliding locking mechanism - Automatic water cooling system - Timer buzzer display for heating and cooling cycles - Possible sizes: Fjdpjt Dvyfjfx Abasgi 1 inch, 1 ½ inch, 2 inch, 30 mm, 40 mm and 50 mm - Power supply: 230 V / 50 Hz - Machine color: 3-Rath design (grey/red)

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S23NEOS21, Exhibition unit ATLANTA NEOS stretch wrapper with articulated arm 99 individually storable programs Start/stop at the same position (corner counter) Wrapping height 2000 mm Mast height approx. 1500 mm (fits through almost any door and in almost any van) Powerstretch PRS 200% film (more available as an option) Motorized pre-stretch system with stepless adjustment Electronically controlled film tension via control unit IEF quick-loading system for easy film roll changes Film specifications: Max. outer diameter Ø300 mm – height = 500 mm – core Ø76 mm Automatic film cutting unit (available as an option) Film tension storable in 4 steps TECHNICAL DETAILS: Two maintenance-free 12 V – 100 Ah AGM batteries connected in series Minimum 160 pallets per Charging – Charging time: 8-10 hours High-frequency battery charger with LED display Wrapping height “Machine with MAST (pallet included) 2,150 mm Height measurement via light sensor or dimension input on the display Protective bar for emergency stop of the drive Emergency stop switch compliant with CE regulations Acoustic warning signal and warning light at machine start Fall protection for the film carriage Push buttons for start & stop Machine function compliant with CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters adjustable via display - Display lock for program changes - Adjustable machine speed around the pallet up to 80 m/min Upward and downward carriage speeds independently adjustable - Upward carriage speed from 1.3 to 5.4 m/min - Downward carriage speed from 1.3 to 5.4 m/min - Number of wraps at the pallet base (1-10 wraps) - Number of wraps at the pallet head (1-10 wraps) - Pallet wrapping height adjustment - Film application tension for foot and head wrapping / ascending and descending, independently adjustable - Film pre-stretch for foot and head wrapping / ascending and descending, independently adjustable Fgedpfx Aboz Iq Trsaji - Ergonomic height for film changes ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 99 storable wrapping programs for the NEOS arm - Cross wrapping (upward/downward) - Simple wrapping (upward only or downward only) - Wrapping cycle with preset start and stop height - Wrapping to a preset height (with the height sensor deactivated) - Wrapping cycle for large pallets - Wrapping cycle for top sheet film - Soft start cycle for applying edge protection - Wrapping cycle with reinforcement and adjustable number of wraps Soft start to reduce film tears on sharp edges Pallet edge wrapping Wrapping cycle with manual or motorized cord formation (optional) Further systems available immediately from our Ludwigsburg warehouse Also available with the ARYA system – automatic film application possible

Condition: excellent (used), Sub-spindle, Y-axis, C-axis FANUC 18i-TB control Turning diameter max 250 mm Fgodpfox A Eupsx Abaji Turning length -555 mm Chuck Diameter -165 mm Main-spindle speeds 50-4'500 rpm Sub-spindle speeds 5'000 rpm Turret head 1+2: 24 positions with 12 driven positions each Tool presetting device Barloader Piece catching device Misc. accessories MARCELS MASCHINEN CH

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), machine/vehicle number: S23SFERA05, Mobile stretch winder ATLANTA SFERA Easy TECHNICAL DETAILS: two maintenance-free AGM batteries 12 V - 100 Ah connected in series 160 pallets per charge - charging time: 8 -10 hours High frequency battery charger with LED indicator Wrapping height “machine with MAST (pallet included) 2,150 mm Height query via light button or by entering dimensions on the display Protective bar for emergency stop of the travel drive Emergency stop switch according to CE regulations Acoustic warning signal and warning light when the machine starts Fall protection for the film slide Push button for start & stop Function of the machine according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters can be set via the display F00 - Screen lock program change F02 - Adjustable machine speed around the pallet up to 80 m/min Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F17 - F20 - Foil pre-stretching foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Display foil consumption (option for PRS - PS) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 6 storable wrapping programs for SFERA EASY F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F21 - Wrapping cycle for large pallets F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE Brake can be adjusted manually from the carriage by means of a tension roller Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Optional: stretch film with core Ø50mm or coreless stretch film Standard connection values: 230 V - 1L+N+PE - 50 HZ Optionally available: -winding height up to 3500mm -FILM CARRIAGE TYPE “FE” (ELECTROMAGNETIC BRAKE) - FILM CARRIAGE TYPE “OPRS - ONE PRE STRETCH" 200% -FILM CARRIAGE TYPE “PRS” (POWER ROLLER STRETCH) 200% - FILM SLIDE TYPE “PS” (POWER STRETCH) 120-400% -Automatic line formation to strengthen the winding .Automatic system for cutting the film in 3 strips for “BANDEROLL WRAPS” - Machine version for temperatures down to -5° C -BATTERIES LITHIUM RELION 2 x 12V Other systems available from the Ludwigsburg warehouse. Fedpoz Indusfx Abajgi Illustration similar.

Condition: excellent (used), Year of construction: 1972, total power requirement 22 kW weight of the machine ca. 8 t Q U O T A T I O N We are pleased to offer you ex our stock, subject to prior sale, and error in technical data : DISKUS Double Disc Surface Grinding Machine in C-form with rotary workpiece feeding system and automatic dressing cycle model DDS 600 RAM year 1972 / 2002 modernized Serial no 6967 _____ Grinding wheels Ø, each 600 mm Grinding wheels bore x height, approx. 75 / 150 mm Grinding wheel speeds Upper wheel 95 – 955 rpm (3-30 m/s) Lower wheel 765 rpm (24 m/s) Grinding spindle drive, each 30 kW Workpiece dimensions: Grinding width (or workpiece diameter) approx. 20 - 120 mm Grinding (workpiece) height max 50 mm Hydraulic infeed impulse 0.0025 – 0.05 mm Total feed way 150 mm External Ø of workpiece carrier disk 810 mm Feeds of rotary workpiece feed system, infinitely variable 25 – 241 mm/s Total electrical load, approx. 50 kW - 380 V - 50 Hz Weight, approx. 8,000 kg Accessories / Special Features: • In 2002 updated IONIC gauge control Model 17A with monitor and direct input of workpiece data including tolerance range, workpiece counting, statistics. The workpieces are continuously measured via two opposite tracer heads, automatically triggering an hydraulic infeed when needed. • Rotary workpiece feed system with Workpiece carrier wheel (Ø 800 mm) and infinitely variable speed adjustment. • Workpiece height check to avoid crashing with griding wheels • Automatic hydraulic dressing device between the two grinding wheels for simultaneous dressing of both wheels. Dressing cycle can be preset (no. of workpieces/time). Hydraulic return of upper grinding slide to original position/workpiece/thickness (saves a lot of time). • ELBARON Oilmist Extractor with stand and adjustable suction cone • Walkable steel podium for easy machine operating and monitoring • Grinding wheel exchanging device, various spare grinding wheels • Central lubrication using grease and oil mist * Separate switch cabinet. * Separate hydraulic unit. • Currently no coolant filtration device available (can may be supplied separately). This machine is ideal for double-sided simultaneous grinding of parallel workpiece surfaces by continuous method, for maximum output and accuracy in mass production (e.g. Bearing rings, Piston rings, washers, hydraulic parts, and other pressed parts.) Fedpfx Asxqrbxobaegi Condition : very good ! Very well maintained ! Please click here to soon view a video of the machine running : ! Delivery : immediately available, FCA Metzingen Payment : 100 % Net, after conclusion of contract, before loading

Condition: used, Grant Aqua 5 Water BathThe Grant Sub Aqua 5 Plus is a digital, unstirred water bath designed for precise temperature control in laboratory applications. It is part of the SUB Aqua Pro series, known for its high-quality construction and reliability.​ Key Specifications Temperature Range: +5°C to 99°C Temperature Stability: ±0.2°C Capacity: 5 liters Internal Dimensions: 281 x 131 x 132 mm External Dimensions: 335 x 215 x 200 mm Heating Power: 0.35 kW Material: High-grade stainless steel tank Display: Digital with PID control for quick heat-up and precision Fgedpfxjxv Ayve Abaei Additional Features: Three programmable temperature presets Countdown timer with audible buzzer Front panel lock-out User-settable sample protection and fixed thermal cut-out Gable polycarbonate lid included​ This model is suitable for applications requiring stable and precise temperature control, such as sample incubation, enzyme reactions, and media preparation.

Condition: used, This listing is for the Grant GD120 Water Bath/Circulator The unit is in full working condition and is ready for immediate use The Grant GD120 is a digitally controlled stirred water bath and circulator ideal for laboratory use, offering high precision and flexibility. Here's a breakdown of its features and capabilities: Key Features Immersion Thermostat with Intelligent Control Optimisation (ICO): Enables adaptive PID control for exceptionally stable temperature regulation. Integral Pump: Built-in circulation pump with a maximum flow rate of 17 L/min, allowing both sample immersion and external fluid circulation. User Interface: Equipped with a clear digital display, a rotor plus two-key control, timer function for reaction timing, and visual + audible alarms to notify operators of critical conditions. Preset Temperature Control: Supports one adjustable operating setpoint plus three preset temperature options for fast switching. Safety Features: Includes float-switch low liquid protection and an adjustable over-temperature cut-out for sample and user safety. Liquid Type Selection: Automatically adjusts heater power and temperature parameters depending on chosen liquid (e.g., water, oil, glycol mixtures). Temperature Range & Accuracy Plastic Tanks (P-series): From around ambient +5 °C up to ~99 °C. Stainless Steel Tanks (S-series): From –15 °C up to ~120 °C. High Stability: ±0.02 °C for stable temperature control. Technical Specifications & Obsolescence The GD120 series includes multiple tank sizes: plastic tanks (P5, P12, P18) and stainless steel tanks (S5, S12, S18, S26, S38), offering varied capacities for different lab needs. This series is now considered obsolete, though it remains functional and reliable for many applications. Fgjdpfoxhfl Esx Abasi Supporting Documentation & Manual Operating Manual: The GD120 is covered by the general purpose stirred thermostatic baths manual (shared with GD100), outlining temperature settings, calibration procedures, safety guidance, and maintenance. Datasheet Summary: Positioned within the broader Grant Optima product range, the GD120 sits between simpler (GD100, up to 100 °C) and higher-spec models (GR150 up to 150 °C, GP200 up to 200 °C)

Condition: good (used), Year of construction: 1987, Twist drill grinding machine Make: SCHANBACHER Type: S 3-50 Year of manufacture: 1987 Technical data: - simple operation - grinding by means of gear motor - twist drill dimensions 3 - 50 mm - point angle 90 - 140 ° - adjustable clearance angle - grinding motor 400 V / 0,25 kW - geared motor for swiveling movement 400 V / 0,12 kW - grinding wheel dimensions - 175 x 22 x 20/90 x 20 mm Fgsdpsmnntmofx Abaoi - space requirement approx. W 810 x D 570 x H 1260 mm - weight approx. 120 kg - with - clamping device - presetting device

Condition: ready for operation (used), Year of construction: 2003, travel distance X-axis: 630 mm, travel distance Y-axis: 765 mm, travel distance Z-axis: 510 mm, controller manufacturer: MAZATROL, controller model: 640M, spindle speed (max.): 12,000 rpm, spindle motor power: 26,000 W, number of slots in tool magazine: 120, number of axes: 5, This 5-axis Mazak Variaxis 630-5X was manufactured in 2003. It features a maximum X-axis travel of 630 mm, Y-axis travel of 765 mm, and Z-axis travel of 510 mm. The machine is equipped with a tool magazine holding 120 positions and a spindle speed of 12,000 rpm. If you are looking to get high-quality machining capabilities, consider the Mazak Variaxis 630-5X vertical machining centre we have for sale. Contact us for further details. • Table size: 500 × 500 mm • Tool magazine capacity: 120 positionsCondition • Machine in working condition • Complete and fully operational • Sale due to reallocation of production assetsAvailability / Sale terms • EXW sale • Technical documentation available upon request • Available for commercial valuation • Possible technical inspection / site visit Fsdpfx Abey Ey N Neaogi • Direct purchase negotiations possible Additional equipment • Pallet system: Palletech – 12 stations + 2 loading/unloading stations • Renishaw workpiece probe • Laser tool presetting • High-pressure coolant system: 18 bar • Belt-type chip conveyor

Condition: used, Hermle Z 200 A Centrifuge – Small Centrifuge A compact centrifuge for doctors and clinical laboratories. The Z 200 A can accommodate up to 12 x 15 ml tubes with conical and round bottoms. Specifications: Capacity: max. 12 x 15 ml / 6 x 50 ml Speed: max. speed/RCF: 6000 rpm / 4185 xg min. speed/RCF: 250 rpm / 7 xg Speed range: 250 - 6000 rpm Speed setting: button-controlled in 250 rpm increments Speed display: preset and actual speed – digital Run time: max. time: 30 min. / continuous operation min. time: 0.5 min. Preset: 0.5 - 30 min. / “Hold” Time setting: 0.5 min. increments via button press Time display: remaining time – digital Brake: fixed braking force with soft stop Features: - Microprocessor-controlled Fgodpfxom Albde Abaei - DC motor, covered - ABS plastic housing, impact-resistant and chemical-resistant Safety: - Lid locking system - Automatic imbalance detection with safety shut-off - Manufactured according to IEC 1010, UVV VBG 7z Dimensions (cm / inches): Width: 28 / 11.0 Height: 26 / 10.2 Depth: 37 / 14.6 Weight: 15 kg / 33.0 lbs Power consumption: 180 W Item condition: used, top condition You can find more centrifuges – new and used – in our shop! International shipping costs available upon request!

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 862 h, load capacity: 8,000 kg, lifting height: 4,565 mm, free lift: 65 mm, fuel type: diesel, mast type: duplex, construction height: 3,465 mm, power: 82 kW (111.49 HP), fork carriage width: 2,015 mm, fork length: 1,600 mm, empty load weight: 12,417 kg, total length: 5,238 mm, drive type: Diesel, construction width: 2,239 mm, Diesel forklift Load center: 900 Fork width: 200 mm Fork thickness: 70 mm ISO class: ISO Class 4 = 5,000 - 10,000 kg Mast type: Duplex Transmission: Techtronix 332+ 3-speed transmission Speed class: 25 Condition: Ready for use and fully functional Technical condition: very good Front tire type: Superelastic Front tire condition: 40 - 60% Rear tire type: Superelastic Rear tire condition: 40 - 60% Fedpfx Ao Ahl Rmobaogi Description: Machine completely workshop-tested, cleaned, and with new UVV and inspection certificates! Machine will be cleaned before delivery! Turret, fork positioner, Hydr. rotating FORK POSITIONER, Series S 11-ZV 80-360°-SO Load capacity 4,500 kg at 1,500 mm load center. Rotation range 360° in both directions, infinitely adjustable fork positioner range 560 - 1,600 mm measured from the outer edge, or 360 - 1,400 mm measured center-to-center. With center stop in front of the carriage rollers, widened slide guide, all hydraulic hoses with heat protection. In addition, the fork positioner has an oil motor protection. The lines of the oil motors are routed in pipes. The hoses are heat-resistant. The cylinder pressure is limited outwards and inwards so that the fork positioner cannot be used for clamping. Technical data: Weight: 2,300 kg ESP: 340 mm Overall dimension: 360 mm (to the rear edge of the carriage) 3rd valve, 4th valve, rear work light, front work light, full cabin, CE certificate, special design, interior mirror, LED, - Drivetrain protection system with engine shutdown - Premium monitoring package - Speed limiter preset to 13 km/h (adjustable) - Mast inclination - 5° forward/6° backward - Accutouch mini-lever hydraulic controls - Automatic hydraulic control - Red seat belt with restraint system - 2 front and 1 rear LED work lights with brake, tail, turn, and reversing lights - Yellow rotating beacon - Activated via ignition switch - Pedestrian warning light (P.A.L) at the front and rear - LED lights mounted on the mast - Red Line (Side) Pedestrian Awareness Lights (Keyswitch Activated) - Key Activated (Automatic) Lights

Condition: excellent (used), Year of construction: 2002, Roland 702 P SW, year 2002, approximately 190 million impressions, Rolandmatic alcohol dampening system Technotrans Beta d refrigeration unit perfecting capability 1+1 / 2+0 high-pile delivery RCI ink and register remote control Fgjdjzv Nduopfx Abaoi PPL semi-automatic plate loading system ink rollers, blanket cylinders, and offset cylinders automatic washing system Grafix powder sprayer Pecom system Preset function Automatic washers

Condition: used, Technical details: x-travel: 130 mm y-travel: - mm z-travel: 140 mm machine weight approx.: 107 kg Fgjdpfx Abeu N Apfsaei dimensions L x W x H: 0,72 x 0,33 x 0,63 m Concentricity Gauge Device and Presetting Device (table device) - application: measuring device for production components (helical tooth gears), testing and adjusting of milling tools Characteristics: - longitudinal axis approx. 100 mm, Ø 280 mm - tool slides: turning range 360 °, tool holder Ø 30 x 80 mm, size LxW: 200x175 mm, with measuring device measuring rod Ø 8 x 400 mm adjustable - vertical slide: pin gage Ø 20 x 80 mm *

Condition: used, Year of construction: 1981, cutting diameter 320 mm saw band length 4670 mm cutting width 580 mm total power requirement 7,4 kW weight of the machine ca. 3 t Sawing range, circular, max. 100 - 320 mm vertical, max. 100/100 x 320/460 mm Length of cut, min./max. 0 - 580 mm Distance from column to saw band, max. 690 mm Cutting speed, infinitely variable 16 - 160 m/min Fgsdpfx Ajt Hwrnsbaji Dimensions of saw band, length x Ø approx. 4,670 x 38 mm Length of remaining pieces, automatic/single cut 100/10 mm Saw blade drive, approx. 4.4 kW Total electrical load, approx. 7.4 kW - 380 V - 50 Hz Weight, approx. 3,000 kg Accessories / Special Features: * Infinitely variable speeds of saw blade motor via servo motor and STOEBER drive. Display of cutting speed on control panel. * Infinitely variable settings of sawing feed with display of the current cutting speed. * Workpiece counter: Number of workpieces can be preset. Selection switch for single cuts / multiple cuts. * Display for band tension and cutting feed. * Automatic motor-driven material feed, controlled by a positioning processor, Model PP 160, with input of the appropriate lengths using a roll conveyor approx. 1,500 mm, with enlargement approx. 2,000 mm. And with a stable roll conveyor for the exterior area, 3,500 mm. * Built-in chip conveyor with coolant device. * Built-on switch cabinet. Condition : Good. Machine can soon be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We have a selection of saws on stock. Please let us know your requirements.

Condition: used, Year of construction: 1985, bore capacity in steel (diameter) 30 mm x-travel 850 mm y-travel 435 mm Control HEIDENHAIN TNC 150 total power requirement 16 kW weight of the machine ca. 3500 kg dimensions of the machine ca. m F E H L M A N N (Switzerland) CNC-Controlled High Precision Drilling and Milling Machine with HEIDENHAIN CNC-Control Model TNC 150 Model PICOMAX 100 CNC – 2 + A * Year 1985 Serial No. 16 085 109 _____ Table travel: Longitudinal ( X-Axis) 850 mm Cross (Y-Axis) 435 mm Milling/Boring head travel vertical ( Z-Axis) 210 mm Table size /Clamping area 500 x 1.570 resp. 390 x 1.280 mm Mounting height below spindle, approx. 140 / 690 mm Height adjustment of Milling head max. 540 mm Distance between spindle and column 450 mm Spindle taper SF 32 Spindle quill travels 210 mm Drilling Capacity approx.. 30 mm Spindle speeds steplessly adjustable 50 – 2,500 rpm Feeds steplessly adjustable 1 – 8.000 mm/Min. Quick feed 8.000 mm/Min. Spindle drive, approx. 6 kW Total electrical load 16 kW - 400 V - 50 Hz Weight, approx. 3,500 kg Accessories / Special Features: * HEIDENHAIN – CNC Path Control System Model TNC 150 with colour Screen Grafik, Subroutines, cycles, Threading cycles, Milling Cycles, etc. Mobile Control unit with electronic handwheel. Ideal for quick set-up and Fgedpfx Abjt Hxa Hsaji approach to the workpiece. * The quill movement can be actuated manually or also by the CNC-Control, * The Drilling depth can be presetted by a 12 fold turret drum for different quillstops and with a digital display of the values on monitor. * The complete Milling/Drilling head can be positioned in 3 different heights and with automatic clamping. * Hi Precision Coordinate table controlled by the XY – CNC axis with hardened ball screw spindles. * With quick change tool holders, chucks, millers, etc. and with coolant device. Condition : Very Good to excellent - Machine under power, ideal for small batch production Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract.

Condition: used, Year of construction: 1980, max. wheel diameter 2500 mm gear width 1200 mm max. module 32 min. module 3 total power requirement 25 kW weight of the machine ca. 60 t dimensions of the machine ca. m Gear , min. / max. 180 / 2,500 mm Module 3 - 32 Helix angle, max. 10 - 35 ° Gear width for straight gears 1,200 mm Stroke length, approx. 100 - 1,200 mm No. of strokes 80 - 350 /min Stroke position adjustable 300 mm Stroke speed 4 - 40 mm Max. weight of workpiece, approx. 18,000 kg Min. / max. no. of teeth 16 / 576 Table size x bore 1,400 x 500 mm Grinding wheel Ø, approx. 500 mm Grinding wheel peripheral speed 34 m/s Total electrical load, approx. 45 kW - 380 V - 50 Hz Weight of machine, approx. 60,000 kg Accessories / Special Features: * Hydrostatic guides in grinding slide, table and in all other guideways. * Completely covered working area with sliding doors. * Automatic grinding process for various cycles, with settings for roughing, finishing, fine finishing and automatic dressing cycle after preset number of teeth. * Profile correction is possible via appropriate dressing, as well as additional movement of grinding slide (depth and width crowning). * Approx. 50 change gears. * Grinding slideTilt display device. * Large coolant device with band filter and oil mist exhaust. * Separate switch cabinet. * Separate hydraulic unit. * Separate oil cooling unit. Condition : Very good. Machine can soon be inspected in our showrooms. It is not under power at present. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. The machine comes directly from a first class gear factory, where it was grinding Quality 5 - 6. Grinding diagrams are available. This type and quality of machine is rarely available. Fgedpet Hwqqofx Abaji Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Condition: used, BIO-CIRCLE Type: RWR 80L Auto KST Description: RWR 80 L KST Fully Automatic PLC Parts Washing System The RWR systems from Bio-Circle are the optimal solution for cleaning internal circuit systems without disassembly. The unit is space-saving, quiet, and very easy to operate. Due to the completely closed system, there is no odor nuisance from the cleaner or the dirty water. External dimensions: approx. 1200 x 800 x 1050 mm Power supply: 400 V 50 Hz plug 16A CEE 5p 6h Fedpfxszgclmj Abaegi Drain: 1 1/4“ outlet Technical specifications: Type of contamination: Limescale, rust (mineral), oil, grease Quantity of parts: Individual parts, small series, low quantities Component geometry: Complete components (without disassembly) Quality seal: Stainless steel, service package available Maximum filling volume: 80 L Tank material: V2A stainless steel Electrical connection: 400V / 50 Hz Heating: 4.5 kW Flow rate: 25 l/min Temperature (preset): 60 °C Total weight of the cleaning system without tank filling: 180 KG Application area: The RWR 80 L KST Fully Automatic PLC has been developed for the plastics injection molding field and can be used wherever cooling channels (circuit systems, lines) need to be cleaned. Application: Fill the RWR 80 L KST Fully Automatic PLC with Power Cleaner KST 2.0. Once the minimum fill level is reached and the system is switched on, the system will begin to heat up. During the heating period, the system can already be connected to the tool via the two hoses. The 5-stage cleaning program and the change of flow direction run automatically after the instructions displayed on the display have been confirmed. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by phone.

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S25SFERA08, Mobile stretch winder ATLANTA SFERA Easy TECHNICAL DETAILS: two maintenance-free AGM batteries 12 V - 100 Ah connected in series 160 pallets per charge - charging time: 8 -10 hours High frequency battery charger with LED indicator Wrapping height “machine with MAST (pallet included) 2000 mm Height query via light button or by entering dimensions on the display Protective bar for emergency stop of the travel drive Emergency stop switch according to CE regulations Acoustic warning signal and warning light when the machine starts Fall protection for the film slide Push button for start & stop Function of the machine according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters can be set via the display F00 - Screen lock program change F02 - Adjustable machine speed around the pallet up to 80 m/min Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F17 - F20 - Foil pre-stretching foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Display foil consumption (option for PRS - PS) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 6 storable wrapping programs for SFERA EASY F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F21 - Wrapping cycle for large pallets F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE Brake can be adjusted manually from the carriage by means of a tension roller Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Optional: stretch film with core Ø50mm or coreless stretch film Standard connection values: 230 V - 1L+N+PE - 50 HZ Optionally available: -winding height up to 2400mm -FILM CARRIAGE TYPE “FE” (ELECTROMAGNETIC BRAKE) - FILM CARRIAGE TYPE “OPRS - ONE PRE STRETCH" 200% -FILM CARRIAGE TYPE “PRS” (POWER ROLLER STRETCH) 200% Fodjz Ipdcopfx Abaegi - FILM SLIDE TYPE “PS” (POWER STRETCH) 120-400% -Automatic line formation to strengthen the winding .Automatic system for cutting the film in 3 strips for “BANDEROLL WRAPS” - Machine version for temperatures down to -5° C -BATTERIES LITHIUM RELION 2 x 12V Other systems available from the Ludwigsburg warehouse. Illustration similar.

Condition: used, mileage: 140,278 km, power: 96 kW (130.52 HP), first registration: 05/2019, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, total length: 7,030 mm, total width: 2,115 mm, total height: 3,065 mm, loading space length: 4,377 mm, loading space width: 2,044 mm, loading space height: 2,146 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, tail-lift, Errors and prior sale excepted! Internal number: 1082. 2K50928 ----EQUIPMENT * SCHUTZ vehicle body with box body * SÖRENSEN tail lift * Reverse camera * Seat belts: 3-point height-adjustable seat belts with pyrotechnic belt tensioners * ABS * Storage: - Storage compartment under driver’s seat (not with seat base cover) - Storage compartments in front doors - Recess above glove compartment - Storage compartments above ventilation outlets in the center dashboard - Removable container under passenger seat - Right lockable glove compartment (5.3 dm³) - Lockable center storage compartment (11.38 dm³) * Driver’s airbag * Interface box for body manufacturer * Exterior mirrors, incl. integrated side indicators and wide-angle inserts Fodpfxoyht H Ej Abaogi * Mechanical brake assist * Rev counter * Electronic Stability Program (ESP) incl. ASR with indicator - Hydraulic brake assist - Hill holder (automatic hold for hill starts) - Load Adaptive Control (adjusts ABS, ASR, and ESP functions to vehicle load) * Power windows front, with comfort function for driver’s side * Transmission: 6-speed manual * Headrests (3) * Paint: solid color * Steering wheel with reach adjustment * Manual headlight leveling * Multifunction display with clock, warnings for headlights on and preset speed limit exceeded, and onboard computer * Particulate filter: diesel soot filter * Upholstery: fabric * Radio pre-wiring (cables and antenna) * Black side protection strips * Power steering * Seats: passenger double bench seat with folding table in center backrest * Seats: driver’s seat with longitudinal, height and backrest adjustment, armrest, and lumbar support * 12V socket in center console * Service interval display * Immobilizer with transponder * Central locking with high-frequency remote control ... and much more. ----The vehicle is in unprepared condition! Nationwide delivery available for an additional charge. Errors and prior sale excepted. We are happy to accept your vehicle as trade-in. Financing / Leasing possible even without down payment! Do you have any questions? We are happy to advise you!

Condition: good (used), Description: The machine is in good technical condition, with the possibility of testing by prior arrangement. Fgjdpfx Abey Amqzeaji Maximum turning diameter: 660 mm Maximum swung diameter: 660 mm Main spindle: - Speed range: 35–5,000 rpm - Main drive power: 22/15 kW - Maximum torque: 349 Nm - Spindle bore: 76 mm - Chuck diameter: 210 mm - Indexing (C axis): 0.0001° Sub spindle: - Speed range: 35–5,000 rpm - Power (10 min/continuous): 18.5/15 kW - Maximum torque: 326 Nm - Chuck diameter: 210 mm - Indexing (C axis): 0.0001° Coolant tank capacity: 300 l Machine power supply: 66 kVA Operating voltage: 400 V / 50 Hz Air pressure: 5 bar, 500 l/min Control system: MAZATROL Fusion 640 MT Flush cooling: - Pump capacity: 20 l/min - Pump pressure: 5 bar Accessories: - Technical documentation - Chip conveyor with coolant - Tool magazine for 20 tools - B axis (positioned at 0.001° increments) - C and Y axes - Sub spindle angular position indexing - Synchronization of main and sub spindle - Tool presetting system (Tool Eye) - Front door locking - 20-position tool magazine - Complete cooling system - Interface for IC memory card

Condition: good (used), Year of construction: 1997, Also available CONQUEST T51 model The used HARDINGE CONQUEST T42L 3-axis motorized CNC lathe is a robust and precise medium-sized inclined bed numerical control lathe, turning length approximately 700mm, bar passage 42m, automatic turret with 12 positions with motorized tools, FANUC 18-T CNC with color LCD and RS232 serial interface for data transfer 5″ ASA spindle maximum revolutions: 4,200 rpm continuous C-axis 20HP spindle power X-axis travel: 172mm Z-axis travel: 575mm machine weight 4,000 Kg. Fsdpfx Abevtrc Sjajgi Complete with 210mm AUTOBLOCK hydraulic chuck, tool presetting, programmable tailstock, 2 motorized tool holders (1 axial and 1 radial), chip evacuator, set of fixed and manual tool holders and backup disk; Year of construction 1997; machine compliant with “CE” standards, in excellent condition.

Condition: used, Year of construction: 1983, workpiece diameter 250 mm centre distance 0 mm honing length max. mm max. module 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Fgjdpfx Abjt Hwzpsaji Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features * Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. * All roughing and finishing infeeds can be adjusted by a decade switch; as well as by table reverse times and fast infeeds with preset times (1sec = Ø 0.04 mm), set on a potentiometer. Ampere display, etc. * Convex honing and conical honing are possible via templates. Asymmetric honing is also possible if the workpiece is prepared appropriately (i.e. pre-shaped). * Separate honing oil unit with magnetic separator and fine filter. * Mechanical tailstocks for manual loading. * Oil mist separator. * Sliding doors with foot switch. * Separate hydraulic unit. Condition : Good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. We have a large selection of gear machines available. Please let us know your requirements.

Condition: used, This listing is for the Grant SAP 2S SUB Aqua Bath The unit is in full working condition and is ready for immediate use The Grant SUB Aqua Pro 2S is a compact, high-performance digital water bath ideal for laboratory applications requiring precise temperature control. Designed to meet the rigorous demands of research, education, and quality control, this model offers a value-for-money solution without compromising on quality or functionality. Fjdpfx Abexv Dbbjajgi Key Specifications Tank Capacity: 2 litres (shallow format) Working Area (L x W): 139 x 289 mm Overall Dimensions (L x W x H): 215 x 335 x 150 mm Temperature Range: Ambient +5ºC to 99ºC Stability (DIN 12876-3 @ 70ºC): ±0.2ºC Resolution: 0.1°C Control: Digital, with programmable presets Weight: ~3 kg Voltage Options: 120V or 230V Included: Lid and base tray Safety Features: Dry start/run dry protection Over-temperature alarm High-temperature safety cut-out