Used Scm Dmc M950 for sale (574)

Condition: excellent (used), Wide belt sander for calibration and fine sanding Working width 1100 mm Min. / max. workpiece height 3 - 120 mm Feed motor power 0.8 kW Sanding belt speed 18 m/sec Sanding belt dimensions 1115 x 2620 mm Hnsdpfx Abstwzyfo Tei Feed speed 4.5 / 9 m/ min Suction connection 3 x 160 mm Compressed air connection 6 bar 1st unit Sanding roller rubber-coated 90 Sh Motor power 11 kW 2nd unit Combi unit Rubber-coated sanding drum 60 Sh Sanding pad, rigid Motor power 11 kW 3. cleaning brush unit Automatic workpiece thickness adjustment at infeed with digital workpiece thickness display Table extension in the outfeed Dimensions approx. L x W x H = 2291 x 1784 x 2350 mm Weight approx. 3000 kg Note used machines: - Subject to errors in technical specifications and prior sale. - Prices quoted are ex location - free loading! - The machines have been cleaned and functionally tested. - All machines are purchased as seen without any warranty. The buyer is free to inspect the machines on site. - Special agreements are only possible in written form. (Inquiries will only be answered with your address and telephone number).

Condition: new, Wide belt sanding machine for calibrating and fine sanding Working width mm 1,100 Min/ Max. working height mm 4/ 170 Sanding belt width mm 1,115 Sanding belt length mm 2,150 Gear motor kW 2.2 Feed speed m/min variable Infeed and outfeed support rollers for long and short workpieces Hnedpfoitvkuex Ab Tsi Oscillating belt cleaning 1st unit Oscillating belt cleaning 2nd unit Oscillating belt cleaning 3rd aggregate 10” touch screen control panel “eye-S” 1. Aggregate steel roller 2. Aggregate rubberized calibrating roller 85SH 3. Aggregate combi-aggregate pneumatic seg. sanding pad /rubberized sanding roller 35 SH Motore power 1st unit kW 18.5 Motor powert 2nd & 3rd aggregate kW 18.5 Version "B" for RRCS with: Pneumatic switching on and off 1st aggregate Pneumatic switching on and off 2nd aggregate Pneumatic switching on and off 3rd aggregate "MESAR" with elastic segmented sanding pad Pneumatic switching on and off of the sanding pad unit electronic adjustment of the working height SPECIAL PRICE! IMMEDIATELY AVAILABLE

Condition: new, Technical data: Working width mm: 1,350 Min./max. working height mm: 4 - 170 Sanding belt width/length mm: 1,370/2,620 Main motor power kW: 18.5 with inverter Feed speed variable m/min: 3.5 - 18 Working units: Hnodjhtuvrepfx Ab Tei 1st unit: "RA" skew-grooved contact roller, Sh 86, diameter 160 mm 2nd unit: Combination: Rubber-coated sanding roller diameter 160 mm, 45 Sh Elastic electronic segmented sanding pad “MESAR” with 24 segments Version C: - Elastic electronic segmented sanding pad “MESAR” complete with: - Pneumatic cylinder (on/off) for automatic engagement/disengagement of the sanding roller sanding pad unit - Activation of segments via electronic control, which synchronizes their operation with feed speed and manages the number of active segments based on the workpiece geometry, allowing selection of more or fewer segments to the left or right of the workpiece. Versions 135: “MESAR 24” with 24 segments, segment width 55 mm, complete with B/24 workpiece scanning bar at infeed Additional equipment: Roller table at infeed and outfeed for long workpieces Perforated table and conveyor belt Vacuum table with 4 kW (5.5 HP) electric fan integrated into machine frame Oscillating blow-off device, 2nd unit Touch screen 10.4” display with ‘eye S’ software integration NOTE: IMAGES ARE SAMPLE PHOTOS OF A SIMILAR SD70!

Condition: new, DMC SD 90 RCS 135 "C-Plus" version Technical specifications: Useful working width mm 1350 min/max Working height (with fixed table) mm 4 – 200 Abrasive belts mm 1,370 x 2,620 Feed speed m/min 3.5-18 working aggregates: “MESAR 46” 46 sectors (30 mm) flexible electronic link sanding pad complete with B/46 workpiece sensing bar in the infeed Hnsdod E Ixzopfx Ab Tei • 1st position: "RA" diagonally ribbed steel contact roller D=250 • 2nd position: COMBI with rubber-coated grinding roller D=175 mm 65 Sh • Floating pressure shoe in 1st position with pneumatic adjustment • 2 grooved rubber coated pressure rollers 2nd and 3rd position • Oscillating blow-off device 1st and 2nd unit • Workpiece cleaning unit with rotating blast nozzles • Motor 1st unit 18.5 kW • Motor 2 with inverter 15 kW Table: • Fixed table working height 900 mm • Infeed roller table for long workpieces • Outfeed roller table for long workpieces • Perforated table and transport carpet 50 Sh • Vacuum table with 4 kW electric fan integrated in the machine frame • Stepless carpet feed from 3.5-18 m/min (gear motor 0.75 kW) Control: • Electronic programming unit "Pro-Sand" • Touch screen 10.4" screen • Door with viewing window on set-up side for machine with 2 working units • LED interior lighting Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: used,

Condition: good (used), Code: 0260 Brand: DMC SCM GROUP Model: UNISAND 2000 - CE Standard Automatic wide belt sander with 2 longitudinal units and 1 transverse unit at the inlet for furniture, joinery, custom-made furnishings, panels, wooden doors, window frames, semi-finished products and various - CE Standard Technical data: Max working width 1350 mm Min working width 52 mm Min length 400 mm Min/max working height 4/170 mm Belt feed with variable speed motor Longitudinal abrasive belt length 1370 x 2620 mm Transverse abrasive belt length 150 x 6550 mm Lamellar belt length 140 x 6300 mm Automatic belt centring Automatic table positioning Digital display of working thickness Control panel with dustproof membrane keyboard Electronic system for belt oscillation Rubber-coated pressure rollers Automatic belt centring 1° Group: Transverse Sanding Pad with development 6550 mm and fitted with a lamellar belt, guarantee of stability and excellent abrasive belt tensioning Sectioned electronic pad "EPICS" with electronic control "HYDRA" with 46 sectors, with centre distance 30 mm Hnedpex Dm Tvofx Ab Tei A LED screen allows verification of the operation of the activated pad sectors The unit is equipped with blowers for cleaning the abrasive belt 2-speed motor power 12/15 Kw Suction hood diameter 160 mm Combined longitudinal calibrating/sanding group with steel roller and sectioned electronic pad 46-sector "EPICS" with centre distance 30 mm Reading barrier 46-sector Abrasive belt dimensions 1370 x 2620 mm Roller diameter 220 mm Motor power 15/18,5 Kw Oscillating blowers with electronic control Sectioned electronic sanding pad "EPICS" with 46 sectors and centre distance 30 mm Reading barrier 46-sector Motor power 15 Kw Oscillating blowers Scotch Brite satin roller Diameter 150 mm Motor power 3 Kw Suction hood diameter 160 mm Vacuum table Electronic control HYDRA 35 Compressed air 8 bar Overall dimensions of assembled machine mm 3200 x 2,900 x 2400 h Overall dimensions for transport mm 3200 x 2300 x 2400 h Weight kg 4400

Condition: ready for operation (used), Year of construction: 2021, This SCM DMC SYSTEM belt sander was manufactured in 2021. It features a working width of 1,350 mm and belt feed speeds ranging from 2 to 16 m/min. Equipped with PRO SAND electronic control and a PLC terminal with a 10.4" LCD color display, it offers advanced user interface capabilities. The machine includes multiple working units for diverse sanding tasks and is powered by inverters for precise speed control. Contact us for more information about this machine. Hedpfx Aoyaqg Tob Tsni Additional equipment • Vacuum Motor: Powered by inverter up to 7.5 kW integrated into machine frame / Conveyor: Rubber-coated belt conveyor 50 Shore / Feed Belt Motor: 4 kW driven by inverter / Console: Integrated with PC eye-M and Maestro Pro Sand electronic control, Tele Service system, 21.5" LED LCD color display • Programs: 1999 Working Programs / Control System: Interactive troubleshooting, self-diagnosis, Full HD display with multi-touchscreen, Maestro Pro Sand software • Operating Temperature: +5 to 35°C/ Additional Features: Virtual keyboard, production report, display of electric and pneumatic diagrams, user manual. Machine Benefits Technical Machine Benefits • Working width: 1350 mm / belt feed speed: 2 to 16 m/min / control: pro sand electronic control / display: plc terminal with 10. 4" lcd color display • Sanding belt dimensions: 150 x 5000 mm / chevron belt dimensions: 140 x 4710 mm; 1370 x 2186 mm • Aggregate 1: tie 5000 working unit for extra table internal cross pad / automatic brake, linear blower, sanding belt cleaning system / aggregate 2: do19 orbiting unit for 19 rotating disc brushes / main motor: 1. 1 kw / rotating disc diameter: 125 mm / aggregate 3 & 4: bf300 working unit for brush roller / brush roller diameter: 300 mm / motor: 4 kw / aggregate 5: sc 2620 operating unit for super-finishing pad / chevron belt dimensions: 1370 x 2186 mm / sanding belt dimensions: 1370 x 2620 mm

Condition: ready for operation (used), Year of construction: 2018, This SCM DMC sd60 belt sander was manufactured in 2018. It features a working width of 1,100 mm and handles materials from 4 to 170 mm in height. Equipped with a main motor of 15 kW, it offers feed speeds of 4.5/9 m/min. Additional features include a rubber-coated calibration roller, sanding roller, hard sanding pad, and electronic controls for precise operation. Consider the opportunity to buy this SCM DMC sd60 belt sander. Contact us for more information. Machine Benefits Technical Machine Benefits • Working width: 1100 mm • Min. /max. Working height: 4 - 170 mm • Sanding belt dimensions: 1115 x 2150 mm • Feed speed: 4. 5 / 9 m/min • Main motor 15 kw (20 hp) Extra Information ontrol Unit Electronic ammeter for the main motor to display current consumption Electronic display of the working height Electronically controlled sanding belt Hnodpfx Ajx Nr Sdjb Tei Electronic working height adjustment Electronic Programming Unit LOGIC 50 K Electronic Programming Unit LOGIC SC with LCD display with two rows of dust-proof polishing keypads and integrated LED signals Workpiece Rubber pressure rollers Kickback protection at the inlet Rubber feed carpet Roller table with two rollers at the inlet and outlet of the work table Pneumatic on/off switching of the roller - 1st unit Pneumatic on/off switching of the roller - 2nd unit TES elastic link sanding pad Pneumatic on/off switching of the sanding pad unit Tools "R" unit with roller "CS" combination unit with roller/sanding pad Rubber-coated calibration roller Rubber-coated sanding roller Hard sanding pad "RA" diagonally ribbed steel contact roller in the first unit

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, grinding width: 1,350 mm, SCM Wide Belt Calibration and Fine Sanding Machine Model: dmc sd 60 RCS 135 Technical Specifications: Working width: 1,100 mm Min./max. working height: 4–170 mm Abrasive belt width: 1,120 mm Abrasive belt length: 2,150 mm Main motor power: 11 (15) kW (HP) Gear motor: 0.45/0.8 (0.6/1.1) kW (HP) Feed speed: 4.5/9 m/min Standard equipment: - R140/85 rubber-coated calibration roller, diameter 140 mm, 85 Shore - 1st position - R160/45 rubber-coated sanding roller, diameter 160 mm, 45 Shore - 2nd position - Hard sanding pad with manual working height adjustment - Motor power for unit 1: 11 kW (15 HP) - Electronic ammeter for main motor indicating current draw - Electronic work height display - Electronically controlled sanding belt oscillation - Rubber pressure rollers Hnjdjtwqn Sepfx Ab Toi - Anti-kickback device at infeed before first unit - 60 Shore rubber feed belt - Roller table with two rollers at infeed and outfeed of working table - Feed belt with two speeds 4.5 / 9 m/min driven by gear motor - Automatic belt centering Including the following special accessories: 1 pc. version "B" for RCS with: pneumatic on/off for roller 1st unit “R” + pneumatic on/off for roller 2nd unit “CS” + “MESAR” elastic segmented sanding pad + pneumatic on/off for sanding pad unit + electronic programming unit “LOGIC 50” + electronic working height adjustment 1 pc. CE safety standards 1 pc. roller table at infeed and outfeed for long workpieces, equipped with 5 non-driven rollers 1 pc. "RA" diagonally grooved steel contact roller, 1st unit 1 pc. main motor 15 kW 1 pc. abrasive belt wear optimizer 1 pc. LED interior lighting 1 pc. door with viewing window on rear side 1 pc. Logic SC control

Condition: used, machine/vehicle number: 007984, Max. machining width: 1300 mm Min. machining thickness: 4 mm Working Table: adjustable Vacuum feed belt: yes No. Operating units: 4 Nr Hnjdpjwqdbmofx Ab Tji

Condition: good (used), Year of construction: 2017, In good technical condition. Year of manufacture: 2017. Suitable for dry deburring and disinfection of metal surfaces. Burr removal. Oxide removal on edges and surface finishing. Manufacturer: SCM Group spa Italy. Model: DMC M950. 400V, 71A. Machine weight: 2260 kg. Hodpfx Abox Ttn Uj Teni

Condition: new, - NEW -GENERAL FEATURES:machine frame and worktable* steel structure with electrical cabinet at the front of the machine* sanding belt infeed from the left side of the machine* motorized table height adjustment* main motor integrated in the machine frameelectrical equipment* electromechanical control panel on the front left side of the machine* automatic star-delta start for the main motor* motor protection switch for the motors* motors in insulation class IP 54emergency and protective devices* Safety microswitch for excess thickness* Automatic brake for immediate stopping of the units* Emergency stop safety edge in the workpiece infeed* Mushroom switch in the workpiece infeed and outfeed* Lockable main switch* Automatic emergency shutdown of the machine in the event of:- sanding belt breakage- untensioned sanding belt- protection against lateral movement of the sanding belt- lack of compressed air- overload of the main motorsNote: the standard version with 400 volts 50 Hz requires a three-phase power supply zero conductor ground the 400 volt power supply is without neutral, a single-phase transformer from the price list must also be ordered. The same transformer must also be ordered for a machine with a voltage higher than 400 volts, regardless of whether a neutral conductor is present or machine version with 220 or 230 volts (50 or 60 Hz) is subject to additional costs (see price list).BASIC MACHINE STANDARD EQUIPMENT- R140/85 rubber-coated calibrating roller diam. 140 mm 85 Sh - 1st pos.- R160/45 rubber-coated sanding roller diam. 160 mm 45 Sh - 2nd pos.- Hard sanding pad with manual adjustment of the working height- Main motor 11 kW (15 HP)- Electronic ammeter for the main motor to display the power consumption- Electronic display of the working height- Electronically controlled sanding belt oscillation- Rubber pressure rollers- Kickback protection in the infeed in front of the first unit- Rubber feed carpet 60 Sh- Roller table with two rollers in the infeed and outfeed of the work table- Carpet feed with two speeds 4,5 / 9 m/min withgeared motor- automatic carpet centeringworking width mm 1.100Min./Max. working height mm 4 - 170Sanding belt width mm 1,115Sanding belt length mm 2,150Main motor power kW (HP) 11 (15)Gear motor kW (HP) 0.45/0.8 (0.6/1.1)Feed speed m/min 4.5/9Consisting of:10.90.87 European Safety Regulations(Mark C.E.)93.07.31 Volt 400 EU93.12.01 Frequency 50 Hz44.44.19 Version "B" for RCS33.31.50 Roller table in infeed and outfeed for long workpieces62.44.50 10" control panel with "eye-S" software integration31.21.60 "RA" inclined ribbed steel contact roller - 1st unit97.50.71 Main motor 15 kW (PS 20) Hedpevwfrnofx Ab Teni

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, main saw diameter: 315 mm, tool diameter: 315 mm, Equipment: CE marking, scorer, TECHNICAL DETAILS Main saw blade diameter: 315 mm Hjdpfeyqyc Esx Ab Toni Maximum tool diameter: 315 mm MACHINE DETAILS Circular saw blade units: 1 Connected load: 4 kW EQUIPMENT Scoring unit Tilting function CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial descriptive documents. The buyer is entitled to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8118

Condition: used, machine/vehicle number: 008407, X axis working area: 6700 mm Y axis working area: 1520 mm Working Table: Pod and Rail Hsdpfx Ajycdaxob Tjni Main Electrospindle power: 12 KW Number of controlled axes: 5 axes Total number of tool changer positions: 48

Condition: used, machine/vehicle number: 008238, X axis working area: 3660 mm Y axis working area: 1550 mm Working Table: Flat table Hnedpfxjx A E Tfs Ab Tei Main Electrospindle power: 12 KW Number of controlled axes: 3 axes Total number of drilling spindles: 12 Total number of tool changer positions: 15

Condition: used, machine/vehicle number: 008108, Max width workable: 1050 mm Max length workable: 2400 mm Hjdew Idduspfx Ab Tsni Max height workable: 250 mm

Condition: used, machine/vehicle number: 008132, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 18 m/min Maximum panel thickness: 60 mm Hnsdsw Idc Repfx Ab Tji Operating Units: 7 nr

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: AH/335516, functionality: fully functional, input voltage: 400 V, input current: 68 A, Equipment: CE marking, TECHNICAL DETAILS Number of processing units: 10 1st unit: Spraying device Tools included Hodpfsyuylusx Ab Tsni 2nd unit: Glue applicator 3rd unit: Pressure rollers Tools included 4th unit: End trimming unit Tools included 5th unit: Rough milling unit Tools included 6th unit: Corner rounding unit Tools included 7th unit: Radius scraping unit Tools included 9th unit: Flat scraping unit Tools included 10th unit: Brushing unit Tools included MACHINE DETAILS Voltage: 400 V Current consumption: 68 A Number of transport packages: 2 EQUIPMENT CE marking

Condition: ready for operation (used), Year of construction: 2020, machine/vehicle number: 3005, functionality: fully functional, travel distance X-axis: 3,700 mm, travel distance Y-axis: 1,870 mm, table length: 3,756 mm, table width: 1,892 mm, Equipment: CE marking, TECHNICAL DETAILS Working area X-axis: 3,700 mm Working area Y-axis: 1,870 mm Table length: 3,756 mm Table width: 1,892 mm Tool clamping system: HSK-F63 Number of tool changer positions: 18 pcs. MACHINE DETAILS System/Software: SCM Maestro Hodeyuyf Uepfx Ab Tjni Dimensions & Weight Dimensions (L x W x H): 6,100 mm x 2,600 mm x 2,450 mm Machine weight: 4,160 kg EQUIPMENT User manual Electrical schematics CE marking CE certificate Drilling tool Bumper Vacuum pump

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, input voltage: 400 V, input current: 42 A, total height: 1,800 mm, total length: 4,800 mm, total width: 1,000 mm, Equipment: CE marking, TECHNICAL DETAILS Hodpfx Aeyux Risb Teni Number of units: 9 1st unit: Pre-milling unit Tools included 2nd unit: Glue application unit 3rd unit: Pressure rollers Tools included 4th unit: End trimming unit Tools included 5th unit: Corner rounding unit Tools included 6th unit: Radius scraper unit Tools included 7th unit: Corner rounding unit Tools included 8th unit: Flat scraper unit Tools included 9th unit: Buffing unit Tools included MACHINE DETAILS Voltage: 400 V Current: 42 A Dimensions (L x W x H): 4,800 mm x 1,000 mm x 1,800 mm EQUIPMENT Glue pot

Condition: good (used), Year of construction: 1994, functionality: fully functional, 4-knife cutterblock, 8 kW, infinitely variable feed, electric height adjustment with digital display, planed table, table rollers, planing height 300 mm, good condition. Transport possible at extra cost! Hnjdpfx Absybqn He Toi

Condition: used, Year of construction: 2011, · Working area: 2,550 x 1,067 mm · X-Y travel: 2,980 x 1,450 mm · Z-axis travel length: 150 mm · Clearance height: 120 mm Drilling Unit F14: · Drilling head with 8 + 6 spindles · 5 individually selectable vertical spindles in X · 3 individually selectable vertical spindles in Y · 4 horizontal spindles in X (2+2) · 2 horizontal spindles in Y (1+1) · Speed: 4,000 rpm (6,000 rpm available as an option) · Power: 2.2 kW · Grid: 32 mm · Drill holder: M10 with 11 mm positive fit · Pneumatic feed stroke: 60 mm Grooving saw unit in "X": · Integrated in the drilling head · Grooving saw blade with a maximum diameter of 120 mm Main milling unit: · Tool interface HSK 63F · Speed: 1,500 – 24,000 rpm, infinitely variable via inverter · Motor power: 6.6 kW (9 HP) from 12,000 rpm (S1) · Motor power: 7.5 kW (10 HP) from 12,000 rpm (S6) · Right-/left-hand rotation · Ceramic bearings · Prepared for use with angle drives Tool changer TR10: Automatic lateral tool changer for 10 tools. · Number of tool positions: 10 · Maximum tool diameter: 120 mm · Maximum weight per tool: 4.5 kg · Maximum total tool weight: 28 kg A central extraction port collects all processing units into a single connection with D=200 mm. This reduces the required extraction capacity to approx. 3,200 m³/h. TVF worktable: The worktable is designed to provide the operator with maximum "freedom of movement." The vacuum quick-clamping system offers maximum flexibility for precise positioning and optimal holding of workpieces. · 4 TVF supports, L=1100 mm, infinitely adjustable in X · 12 TVF vacuum cups 120 x 120 mm, infinitely adjustable in Y Hnsdpfoyuw T Nsx Ab Toi · 2 stops in X (1 left / 1 right) · 1 stop in Y per support (total 4 pcs.) · Retractable reference stops controlled via CNC Automatic central lubrication: The correct amount of lubricating grease is distributed via an electronic CNC control unit (X, Y, Z axes) Vacuum system (base machine): · Vacuum pump: 90 m³/h · Power: 2.2 kW · Max. negative pressure (at pump): 0.9 bar PROGRAMMING SYSTEM XILOG PLUS Software features: - Import of DXF files - Import of ASCII files - User interface in operator’s native language Safety devices with bumpers Machine technical data: · Total connected load max.: 18 kW · Recommended fuse: 64 A · Power supply: 400 V 50-60 Hz · Compressed air: 6-7 bar · System pressure (recommended): 8 bar · Compressed air consumption: 200 Nl/min · Central extraction port Ø: 200 mm · Extraction speed: 30 m/sec · Air consumption (central extraction): 3,200 m³/h · Negative pressure: 3,000 Pascal · Weight: approx. 2,500 kg Remote control of machine functions 6 TVF supports L=1,100 mm and 18 vacuum cups 120x120 mm Cross lasers for vacuum cup positioning Two cross lasers mounted on the unit carrier allow for easy positioning of the vacuum cups. Location: Nattheim

Condition: used, Year of construction: 2014, total height: 2,800 mm, total length: 10,300 mm, total width: 2,450 mm, Empty weight: 6.600 kg Price: On request - Details: - └ Description: Machine currently not working: Problem in the canbus system - Year: 2014 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA2/002546 - Number of milling spindles [pcs.]: 1 - Type milling table: Beam table - Tool clamping system: HSK-F63 - Material clamp system: Pneumatic - Drilling unit present: Yes - Tool changer positions [pcs.]: 24 - System/software: Xilog plus - Safety feature: Safety light curtain, Door interlock switches, Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Type: Vtlf 250 - └ Year of manufacture: 2008 - └ Main motor power [kW]: 5.5 - └ Connection diameter [mm]: 70 - └ Oil free: Yes Hedeytcl Iopfx Ab Tjni - Tools included: Yes - CNC options: Offcut conveyor, Manual control - CNC documentation available: USB stick - Table length [mm]: 5200 - Table width [mm]: 1300 - Voltage [V]: 400 - Current consumption [A]: 64 - Transport dimensions: 10300mm x 2450mm x 2800mm (l x w x h) - Transport weight [kg]: 6600kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2012, operating hours: 6,586 h, total height: 2,700 mm, total length: 8,100 mm, total width: 2,450 mm, Empty weight: 4.665 kg Price: On request - Year: 2012 - Documentation available: No - CE certificate present: No - Serial number: AA2/001992 - Operating hours: 6586 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 4 - - C-axis present: Yes - └ Milling spindle 2: - - C-axis present: Yes - Type milling table: Beam table - Tool clamping system: HSK-F63 - Material clamp system: Pneumatic - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 2 - Tool changer positions [pcs.]: 12 - System/software: Xilog plus - Safety feature: Door interlock switches, Enclosed fence, Safety mat - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Type: Vtlf 250 - └ Year of manufacture: 2001 - └ Main motor power [kW]: 5.5 - └ Capacity [m³/h]: 250 - └ Connection diameter [mm]: 70 - └ Vacuum pressure [bar]: 800 - └ Oil free: Yes - Tools included: Yes - CNC options: Manual control, Offcut conveyor Hodeyr Iqaspfx Ab Tjni - Table length [mm]: 6000 - Table width [mm]: 1300 - Voltage [V]: 400 - Current consumption [A]: 47 - Fuse [A]: 63 - Transport dimensions: 8100mm x 2450mm x 2700mm (l x w x h) - Transport weight [kg]: 4665kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: good (used), Code: 0326 Brand: SCM MINIMAX Model: CU 350 K - CE Standard Universal 7-works combined machine for joinery, furniture, custom-made furnishings, doors, wooden window frames , panels and various – CE Standard Technical data: Aluminium carriage sliding on hardened and ground steel guides 3000 mm Surface planer: Surface planer width 350 mm Total table length 1800 mm Spindle speed 4850 rpm Guide incliantion 90–45° N° 3 cutters Thickness planer: Table dimensions 600 x 350 mm Min/max working height 3–230 mm Max removal 5 mm Hsdpfxsyuxplo Ab Teni Spindle moulder: Spindle length 136 mm Rotation speed 1400/3500/6000/8000 rpm Max tool diameter 180 mm Cover with vertical clamps Circular saw: Aluminium carriage length 3000 mm Tilting blade 0–45° Max blade diameter 300 mm Spindle speed rpm 4000 Cutting width at parallel guide 900 mm Squaring frame fitted with telescopic guide with 2 adjustable reference stops Protective cover Mortising machine: Table dimensions 430 x 220 mm Workpiece clamping presser Vertical stroke 100 mm Transversal stroke 155 mm Longitudinal stroke 115 mm N° 3 motors 3 Hp each Suction inlets diameter 120 mm Overall dimensions of mounted machine mm 3000 x 2800 x 1150 h Overall dimensions for transport mm 3000 x 1400 x 1300 h Weight kg 690