Used Universal Cylindrical Grinder for sale (5,898)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm Kjdpfx Asuxfu Nsb Toln - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your sion R: Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock. Beispielfoto einer von uns überholten 600U -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter weiteres Zubehör auf Anfrage. Overhauled with geometric KELLENBERGER protocoll. Standard with: -2-axis DRO -Paper filtration Klodpfjd Ih D Hex Ab Ten Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 1982, grinding diameter 630 mm grinding length 600 mm centre height 320 mm Maschine wird überholt nach Kellenberger Messprotokoll und neu lackiert. Die anfällige Güttinger Steuerung wird durch die zeitgemäße BEMA X Steuerung ersetzt. Das heißt die Maschine erhält in diesem zuge auch eine komplett neue Elektrik. Siehe Beispielfotos. Maschine mit verstärktem Werkstückspindelstock zum fliegend Schleifen von schweren Werkstücken. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den Kledpfx Ajvq R Uzjb Ton grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 1982, grinding diameter 630 mm grinding length 600 mm centre height 320 mm Machine with heavy duty workhead. Machine will be partial overhauled before delivery. Machine will get a geometry protocoll according to the Kellenberger new machine guideline Kjdpev Dxxzefx Ab Teln

Condition: used, Year of construction: 2002, grinding diameter 250 mm grinding length 400 mm centre height 125 mm Control Fanuc 21i-T Ksdsvx Dvujpfx Ab Teln Maschine gewartet und teilüberholt. -Neue Schleifspindellagerung -Neue x-Achs Spindel -Obertisch überschliffen -Neue Geometrie Tischgeometrie -Neue Geometrie WSS zu Schleifspindeln B-Achse mit 1° Hirth Verzahnung Längspositionierung HF-Innenschleifspindel GAP Papierbandfilter

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your o von Kürzlich gelieferten Maschinen mit zusätzlichen Optionen wie: -Spritzschutztüren -Kabine x-Achse -Schwenkwinkelanzeige Schleifspindelstock Geometrisch überholt und neu lackiert mit original Elektrik. Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock serienmäßig. -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 Klsdpsuxftxofx Ab Ten genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 350,450 mm grinding length 600 mm centre height 175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. Foto von bereits gelieferter Maschine mit eventuell anderen Optionen. Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock serienmäßig. BEMA Standard serienmäßig: -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my -Drehzahlanzeige Schleifspindel -Stufenlose Drehzahl Schleifspindel 70-100% -Stufenlose Drehzahl Innenschleifspindel 70-100% -Werkstückspindelantrieb durch Drehstrommotor stufenlos regelbar über Frequenzumrichter Mögliche Optionen gegen Aufpreis: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Sinuslineal -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: Ksdpfjd Ih D Esx Ab Toln -Bedienwerkzeug -Spannrohr für Futter Natürlich erhalten Sie auf unsere generalüberhalten Maschinen 12 Monate Gewährleistung. (Nur Anrainerstaaten) weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm Kjdpfx Aet Ii Rrob Teln weight of the machine ca. 3 t High-End Kellenberger 1500U Ideal for spindle producer or overhauler -BEMA Internal grinding device with separate, cooled motor. Grinding spindle and internal grinding spindle motor electrically interlocked! Internal grinding spindle can only be switched on when it is in position. A quantum leap in safety -Infinitely variable grinding spindle speed 1000-1500 rpm -Infinitely variable internal grinding spindle speed 0-100%. -Digital display of grinding spindle speeds -Swivelling angle display top table -swivel angle display grinding headstock -Marposs gaper sensor for external grinding only -fluid gating sensor Marposs internal grinding -Center height up to 250mm possible Machine is already delivered. Identical machine can be built with additional with additional options. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° Kljdov I Eq Sspfx Ab Tjn grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m Ready for delivery, with 12 month warranty in germany and neighbouring countries! Geometrically overhauled and repainted with new electrics. In KELLENBERGER quality!!! -Digital display in 2 axes. Resolution x-axis 0.5my -Modern workpiece headstock with cone MK5 -Modern tailstock with cone MK3 -Modern hydraulic unit -Paper belt filter Further accessories on request

Condition: used, Year of construction: 2010, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control Fanuc 310is Completely machanically overhauled with grinding process and setup of one part. Original photo taken on the EMO 2010. Ksdpfxevdk N Es Ab Tjln CNC control GE Fanuc 310is Hand panel for CNC control GE Fanuc Wenger loader optional Turned part with automatic indexing 1° Grinding head UR 1-2-3 Grinding wheel equipment left 500 x 80 mm Grinding wheel equipment right 400 x 63 mm Operating unit for one high-speed internal grinding spindle MFV / MFZ High-frequency internal grinding spindle MFN 1090 Coolant supply through the workpiece spindle Dressing unit on the upper table Swivelling holder for PCD diamond plates Basic module for KEL-TOUCH gate sensor and KEL-BALANCE balancing devices KEL-TOUCH lead sensor for universal grinding head variants R / RS / UR / URS KEL-TOUCH on the workpiece headstock for internal and external grinding Preparations for Movomatic ESZ 400 or Marposs P7 ME measuring controls Preparation for external filters Cooling lubricant switch-off for table devices Full casing emulsion Emulsion sanding mist extraction system Maintenance unit for additional pneumatic functions Preparation for KEL-VITA gantry loader KEL-POS, MOVOMATIC: C25 measuring probe Hydraulic preparation for arobo bezel

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 D-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Further options available on request Klodpfxeuxfucs Ab Ten Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Control system: The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: used, Year of construction: 2006, grinding diameter 350 mm Kljdpfx Ast Ii Nbjb Ton grinding length 1000 mm centre height 175 mm weight of the machine ca. 3,5 t Machine completely overhauled with 12 months warranty Mechanically and optically like new Photos from the last overhauled machine with different options Fanuc 21i control -Grinding head UR 1-2-3 external/internal/plan -Axis automatic 1° Hirth serration -Active longitudinal positioning KEL-POS Movomatic -Semi-automatic balancing device KEL-BALANCE -Grinding wheel equipment left 400mm diameter -Grinding wheel equipment right 300mm diameter -Internal grinding unit with belt drive -Tailstock with micro-adjustment -fine adjustment upper table -Paper belt filter SBP4 240l

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. Geometrically overhauled with new paint and original electrics. Foto of a 600U which we already have delivered. -Digital display in 2 axes. Resolution of x-Achse 0,5my Options: -Encoder with digital display in workpiece spindle head -Encoder with digital display in grinding spindle head (Height adjustment with spindle not possible) -New stable internal grinding diameter 80mm oder 100mm with height-adjustment. -Increase the center heigh to max. 225mm -Speed control of the grinding spindle Including:: -Adjustment tool -Draw tube for chucks other accessories on reqeust Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln. Ksdpfjt Ii Nujx Ab Tsln

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-9,99 mm/Ø 0-9,99 mm/Ø ±8 ° longitudinal feed of the table 1100 mm table speeds 0,02-6 m/min 130 kg cross travel max. 270 mm 130 inkl. Spannung kg 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including new, modern and future-proof control system. Photo of already delivered machine in centre distance 1000mm. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Possible options: -Semi-automatic dressing cycles for external and internal grinding Kljdouxfupopfx Ab Tsn -automatic dressing compensation. -Measuring control

Condition: used, Year of construction: 1995, machine/vehicle number: UWIIA/3472/95, max. grinding diameter:300 mm grinding length:400 mm workpiece length:520 mm Kljdpecxxrfjfx Ab Tsn centre height:150 mm :550 mm table speed -stepless-:0,005 - 5,0 m/min centre distance:350 mm :250/3750/5000/7500 U/min max. dia. of grinding wheel:250 mm grinding spindle head - swivable:11-60 ° drive capacity - spindle motor:max 3,0 kW total power requirement:7,7 kW with SIEMENS 810 G3 CNC control, electric hand wheel and spindle pitch-correction unit, FORKART OVERZ-BR hydraulic collet chuck, coolant device, automatic central lubrication, encasement with movable observation window at operator's station, separate electrical cabinet, machine light, SIEMENS servo drives, very good condition

Condition: used, Year of construction: 1982, grinding diameter:250 mm grinding length:650 mm centre height:125 mm internal grinding spindle rev.-stepless:9500-50000 U/min workpiece speeds -stepless:50-10000 mm/min grinding head swivelling:90 Grad max. dia. of grinding wheel:400 mm spindle bore:30 mm grinding length - plunge feed:80 (100) mm max. grinding depth by internal grinding:ca. 170 mm max. bore diameter to be ground:90 mm feed speeds:240 mm/min max. workpiece weight:80 kg required cooling water:36 l/min centre distance:650 mm distance of workpiece spindle-taper cone:960 mm drive capacity - spindle motor:6,25 kW connected load:ca. 10 kW total power requirement:8,5 kW weight of the machine ca.:3,4 t Klodocxxubopfx Ab Ton dimensions of the machine ca.:3,9 x 2,5 x 1,85 m with Studer control, electric/hydraulic drive, variable speed, tailstock with fine adjustment and hydraulic back feed, work piece headstock with increased precision, table air , hydraulic removable dressing device, radius-dressing device, Hydro-Cyclone filter, automatic grinding wheel-balancing device, automatic dressing cycle with speed compensation

Condition: used, Year of construction: 1987, machine/vehicle number: 6004.01, grinding diameter:350 mm grinding length:1000 mm centre height:175 mm workpiece weight:120 kg power capacity:5,5 kW turning speeds:max. 25000 U/min Kedpfx Asdmppqjb Tsln control:FMS 5-88 weight of the machine ca.:3,5 t precision grinding machine with SONY digital display, coolant system, electronic hand wheel, separate electrical cabinet, emergency cut-off

Condition: used, Year of construction: 2010, grinding length 1025 mm grinding width 520 mm Control SINUMERIK 840 D tool taper HSK-A 63 A - axis ° workpiece weight 30 kg Klsdpfx Abjvxwine Ton distance grinding spindle - table min./max. 473,5 - 1023,5 mm x-axis 520 mm y-axis 550 mm z-axis 1000 mm V-axis 166 mm feed x-axis 4 - 6.000 mm/min feed y- axis 4 - 4.000 mm/min Feed z- axis 30 - 25.000 mm / min. table dimensions 1.400 x 874 mm spindle speeds (infinitely variable) 0 - 12.000 U/min power capacity - grinding motor 35,00 kW grinding wheel diam. min/max. 100 / 300 grinding wheel width 60 mm total power requirement 100,00 kW weight of the machine ca. 11,00 t dimensions of the machine ca. 8,60 x 7,25 x H3,80 m 5 Axis Profile grinding machine, with SIEMENS SIN840D, double dividing head (B-C axis), V-axis (coolant nozzles), EROWA tool changing device (machine can also be operated without a tool changer), fire extinguishing device, Renishaw probe prepared. Without Host-Computer for workpiece- tool-management. without coolant device - was connected to the central supply.

Condition: good (used), Year of construction: 1981, functionality: fully functional, workpiece weight (max.): 10,000 kg, grinding length: 4,000 mm, grinding wheel diameter: 750 mm, total width: 4,180 mm, total length: 13,440 mm, total height: 2,455 mm, grinding diameter: 800 mm, overall weight: 38,700 kg, STANKO 3M196 roller grinder. Year of manufacture 1981. Kedet I Dppspfx Ab Tsln Max. grinding diameter 800 mm, Max. length of ground workpiece 4000 mm, Range of grinding diameters 80 - 800 mm, Max. grinding diameter without support 800 mm, Max. grinding diameter in support 450 mm, Elevation of the tusk above the table 410 mm, Max. weight of ground workpiece in the tusk 10000 kg, Grinding wheel dimensions ⌀750 x 100 mm, Grinding speed 50 m/s, Main motor power 30 kW, Product speed 5 - 80 rpm, Max. travel of tailstock tusk pins 100 mm, Overall dimensions of the grinder (Length x Width x Height ): 13440 × 4180 × 2455 mm, Weight of the grinder 38700 kg,

Condition: used, Year of construction: 1977, Manufacturer: PONAR Klsdpow Iqi Rjfx Ab Ton Model: RUP 28x45 Weight: 1800 kg

Condition: like new (used), Year of construction: 2024, functionality: fully functional, grinding length: 1,650 mm, grinding diameter: 400 mm, We offer a new BUB40 x 1500 NC machine equipped with a MITSHUBISHI NC controller. The machine is still under lease with ING Lease. It has been thoroughly refurbished based on the TOS HOSTIVAR BUB 40 model by FAS GŁOWNO. Technical data: • Maximum workpiece diameter: 400mm • Maximum workpiece length: 1500mm • Centre height: 200mm • Distance between centres: 1500mm • Minimum grindable workpiece diameter with a 380 mm grinding wheel: 20mm • Tailstock quill stroke: 40mm • Maximum tailstock clamping force: 4000N • Spindle headstock centre taper: ISO 296-1991/Morse 5 • Tailstock centre taper: ISO 296-1991/Morse 5 • Maximum workpiece weight between centres: 500kg • Maximum workpiece weight in chuck (including chuck): 100kg • Machine width (with enclosure): 6650mm • Machine depth (with enclosure, without control panel): 2400mm • Machine height (with enclosure): 1850mm • Machine weight: 7000kg • Total power requirement: 38kVA Grinding spindle: • Standard grinding wheel dimensions: 500 x 80 x 203.2mm • Grinding spindle drive motor power: 11kW • Grinding spindle rated speeds (for 430 mm / for >430 mm and 500 mm wheels): 2000 / 1744 rpm • Grinding headstock traverse servo motor power: 2kW • Grinding headstock traverse servo motor torque: 9.5Nm • Maximum continuous X-axis traverse speed: 2m/min • Minimum X-axis grinding wheel increment: 0.001mm • Maximum continuous X-axis traverse speed: 6m/min • Minimum X-axis grinding wheel increment: 0.001mm • Maximum grinding wheel increment in INC mode: 0.1 mm • Table traverse servo motor power: 3.5 kW • Table traverse servo motor torque: 16.7 Nm Workpiece spindle: • Workpiece spindle speed range: 1 – 150 rpm Kedjwzkywopfx Ab Tjln • Workpiece spindle servo motor power: 3.5kW • Workpiece spindle servo motor torque: 16.7Nm More information available upon request via email or phone.

Condition: reconditioned (used), Year of construction: 2024, functionality: fully functional, grinding wheel diameter: 500 mm, total width: 2,300 mm, total length: 6,730 mm, total height: 1,800 mm, grinding diameter: 320 mm, workpiece weight between centers: 250 g, grinding wheel width: 80 mm, spindle speed (max.): 1,800 rpm, feed length X-axis: 350 mm, feed length Z-axis: 1,550 mm, Good morning, We have to offer a six months old CNC SWG32 x 1500 CNC machine with SIEMENS SINUMERIC 828D sL control (after a complete revitalization of TOS HOSTIVAR BUB32 machine) The machine is still in Lease at ING Lease. The machine has already been partially repaid, our company does not want to recover the repaid installments. The assignment of the lease applies only to the remaining installments to be repaid (the cost of the assignment is borne by our company). For more technical and financial details, I invite you to contact me at the e-mail address or by phone Specification of the machine: - Year of manufacture:2024 - Maximum grinding diameter: 320 - Maximum grinding length: 1500 - Supply voltage: 3 x 400V - Control voltage: 24V - DC - Metric system - Maximum permissible weight of objects clamped in the canine: 250 kg - Total travel distance in the X axis: 350mm - Rotation of the grinding wheel spindle: 50 - 1500 rpm (7.5kW) - Plunge grinding infeed speed range 0.03 to 20mm/min - Wheel diameter: 500mm - Morse taper 5 - Measuring probe to determine the workpiece - Workpiece support - Electronic wheel (handheld panel) Klsdpjvkc D Ijfx Ab Tjn

Year of construction: 1979, condition: refurbished (used), functionality: fully functional, TECHNICAL DETAILS Height of centers: 125 mm + heights of 50 mm distance between centers: 1.000 mm Grinding wheel ' diameter: 400 mm ' width: 50 mm ' Bore: 127.0 mm angular displacement: 270 ° workpiece spindle head: 20 - 400 rpm Kodpfjk H Hp Nsx Ab Tsln taper of the spindle: 5 MT Taper in the tailstock: 3 MT table angular displacement: 8 ° Table speed: infinitely variable up to 6.0 m/min Internal grinding spindle with 60 000 rpm External grinding wheel motor: 4,0 kW Workpiece spindle motor: 1,5 kW Weight machine: 3.100 kg Overall machine dimensions: 2,860 × 1,680 × 1,670 mm (L × W × H) EQUIPMENT & SCOPE OF DELIVERY - Machine was completely retrofitted - New control cabinet & new wiring diagram - New motor & frequency converter for the working head - 2 axes DRO - Cooling tank with paper filtering - Geometry made according to the Kellenberger protocol - Internal grinding spindle - Many accessories Please refer to the attachment below for a test report on the machine.

Condition: used, Year of construction: 2022, operating hours: 4,264 h, grinding length: 500 mm, grinding width: 300 mm, CNC CYLINDRICAL GRINDER OGM-350 UNC III by OKAMOTO Equipped with Fanuc 0i control, 2 interpolated axes Grinding diameter: 300 mm Grinding length: 500 mm KEY FEATURES OF THE GRINDER - User-friendly CNC control - FANUC 0i, 2 interpolated axes - Conversational programming - Programmable in-feed dressing with compensation - Automatic rapid infeed and retraction of the workhead - Dimensional compensation - Interruption for dressing function - Automatic calculation of swiveling angle for table positioning - Sturdy construction and functional machine bed design - Electronic handwheel - Spindles: high-precision roller bearings for the grinding and workhead spindles with lubrication for long life - Ultra-precise ball screws for X and Z axes, directly coupled AC servo motors STANDARD EQUIPMENT LIST - Grinding wheel Ø 405x50 (UNC) - Grinding wheel flange, mounting Ø 127 mm - Separate electronic (portable) handwheel for X/Z axes - Machine enclosure with large front sliding doors - Tailstock with sleeve and manual lever - Micrometric cylindricality adjustment of the tailstock - 7.5 kW grinding motor - Infinitely variable grinding spindle drive - Grinding speed up to 45 m/s - Automatic central lubrication - Device for automatic longitudinal or plunge positioning, including measuring head and software - GAP-Eliminator with sensor (reduces “air grinding” time during multiple infeeds) - Balancing arbor - 10.4'' color touchscreen panel with graphic interface - Leveling screws and plates - Service tool kit - Dressing tool holder including diamond - Operating manual - Machine painted in OKAMOTO gray-beige (Munsel 5Y6/1) or according to specification at extra cost - Machine equipment compliant with CE standard Klsdpjwqcazefx Ab Tjn

Condition: reconditioned (used), Completely overhauled grinder for external and round grinding LŽT Kikinda, type AFC 630/1000/1600/2100 and UFC 630/1000/1600/2100 Machine Feature: Max. Spike spacing 630/1000/1600/2100 mm Kjdpfx Absv Tavms Toln spike height 180 mm largest diameter of the workpiece 360 mm maximum workpiece weight 300 kg dimensions of the grinding wheel 500x203x100 mm The accuracy of the machine max. 5 microns Electrical components manufactured by ABB, Schnieder Painting in the final color according to the customer's wishes Warranty on works: 6 months Delivery time: negotiable For more information, call.