Cylindrical Grinding Machine - Universal

KELLENBERGER 600U BEMA Advance

Condition: used, grinding diameter 250,350,450 mm grinding length 600 mm Iiedod Ih D Nepfx Akxof centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your rhauled with geometric KELLENBERGER protocoll -2-axis DRO -Paper filtration Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 2000, table length 1160 mm table width 710 mm daylight 650 mm Control WENZEL ME 5007 total power requirement kW weight of the machine ca. 800 kg dimensions of the machine ca. m 3-D-coordinate measuring machine with METROLOG II-Software Iiodpet Hw S Ijfx Akxjf

Condition: good (used), GENERAL CHARACTERISTICS Max. Ø to be ground 120 mm Grinding wheel width 250 mm Minimum Ø to be ground 1 mm Ø drive grinding wheel 304 mm Ø working wheel 508 mm DIMENSIONS AND WEIGHT Height 1,700 mm Width 1,500 mm Length 2,750 mm Weight 4,000kg Iedpfx Akjrpnf Ajxsif ELECTRICAL CHARACTERISTICS Grinding head motor power 15 Kw Spindle head motor power 1,8kw Hydraulic motor power 1,1kw Total power 20 kW Voltage 220/380 V

Condition: new, Continuous power: 60 kW / 75 kVA Engine: Fawde 4110/125Z-09D, 4 cylinder, water-cooled Connection: 1x32A, 1x64A 1x220V Sockets or circuit breakers, optional 125A socket Frequency: 50Hz Iisdpfx Aksh R Tm Ioxef Voltage: 400/230V including electronic speed control, AVR, battery charger, preheater Comap AMF8 control with generator network grid feed in RCD protection

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing Iisdpfjqt Dmyjx Akxof - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: as good as new (ex-display), Year of construction: 2026, Centre height: 181 mm Centre distance: 1000 mm Maximum grindable workpiece diameter: 360 mm Max load cantilevered: 1000 N (100 kg) Max load between centres: 3000 N (300 kg) Z-axis: Table swivel angle: 10° Table drive, hydraulic: 0–4 m/min X-axis: Cross slide travel: 80 mm Rapid traverse (hydraulic): 50 mm Coarse adjustment – air cushion: 280 mm Infeed drive by DC motor Rapid infeed speed: 48 mm/min/Ø Infeed cycle: Plunge grinding / Longitudinal grinding 4 preselectable speeds: mm/min/Ø: 0.01–48 4 preselectable infeed increments: mm: 0.001–0.1 Automatic shut-off during stop-grinding: 0–99 s or 0–99 strokes Stepwise infeed: mm/Ø: 0.001 Grinding headstock universal, swivelling: 0–180° Grinding wheel (OD): D x width x bore: 500 x 100 x 127 mm or 203.2 mm Grinding wheel (face, option) D: 250 x 32 x 76.2 mm Grinding wheel (ID, option) D: 2–250 mm Drive power, external/face: 5.5 (7.5) kW Drive power, internal: 2.2 kW Peripheral speed, external: 35 (50) m/s Grinding wheel wear (OD): mm/Ø: 160 Guard width: 100 mm Grinding spindle diameter: 60 mm Internal spindle mounting: 80 (100) mm Workpiece headstock: Infinitely variable drive: MK 4, 1/min: 30–270 / 50–450 Workpiece spindle lockable Spindle mounting: MK 4/24 mm Spindle nose for flange attachment: MK 4, cylindrical Ø63H6 x 6 mm Headstock swivels on rotating part: 0–90° Tailstock: Quill mounting / Quill diameter: MK 4, 750 mm Quill stroke: 45 mm Quill force, N: 100–800 / 250–1400 adjustable Quill operation: manual (foot switch) Quill fine adjustment: ±40 μm Connections: Total machine connected load: 6.5–10 kW Grinding headstock: 5.5 (7.5) kW Workpiece headstock: 0.55 (1.1) kW Coolant filtration: 0.75–2.2 kW Ijdetqf Rzopfx Akxsif Lubrication pump – guideways: 0.1 kW Hydraulic pump: 1.5 kW Hydraulic tank: 80 l Pneumatics: 6 bar Comparable to: Weiss / EMAG / GP cylindrical grinders / Studer / Kellenberger / Schaudt / Tschudin / Tacchella / Dannobat

Condition: like new (used), Manual profile grinder UTMA model P20 Iiedoff H E Ropfx Akxjf

Condition: good (used), centerless grinding machine Iiedpotrguvefx Akxjf

Year of construction: 2014, condition: excellent (used), DMG PH 150-8 . year of construction 2014 . with pallets . Iiedjin Dklopfx Akxef Touch screen . plant in very good condition .

Condition: used, total height: 1,800 mm, total length: 3,500 mm, total width: 2,300 mm, Empty weight: 5.800 kg Price: On request Grinding diameter: 315mm Grinding depth: 500mm Swing: 500/600mm Stroke of table: 800mm - Documentation available: No - CE certificate present: No - Serial number: 31577 - Drive system: Conventional - Grinding diameter [mm]: 315 - X-axis travel [mm]: 800 - Transport dimensions: 3500mm x 2300mm x 1800mm (l x w x h) - Transport weight [kg]: 5800kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Ijdewya A Sepfx Akxeif Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum