Used Wollmer Chp for sale (203)

Year of construction: 2014, condition: good (used), functionality: fully functional, machine/vehicle number: 3GBG252051-ADK,002,009, The machine is a wood gasifier that converts the gas from wood chips into electricity that is generated from a 6-cylinder GM engine. The machine was acquired as part of the property that includes a boutique hotel. It was subsequently shut down when we did not have the capacity to operate it and the hotel. We expected to once again redeploy it but the base business keeps us too busy to add the operation and maintenance required of the machine. Bedpfx Ane Adl Hropjlp

Condition: like new (used), Year of construction: 2024, operating hours: 24 h, functionality: fully functional, number of cylinders: 12, cubic capacity: 21,970 cm³, rotational speed (min.): 1,500 rpm, type of cooling: water, CHP POWER PLANT fueled by SYNGAS (Woodgas) with electrical capacity 140 kWel and thermal capacity 280kWth Bjdpfxjz Iyq Ts Anpslp

Condition: new, Year of construction: 2022, functionality: fully functional, type of input current: three-phase, power: 50 kW (67.98 HP), input voltage: 400 V, fuel: domestic gas H, overall weight: 2,200 kg, nominal power: 50 kW (67.98 HP), input frequency: 50 Hz, continuous power: 50 kW (67.98 HP), input current: 72 A, Equipment: documentation/manual, For sale: new and unused 2G g box 50plus combined heat and power (CHP) unit from 2022. This is a 2G Energietechnik g box 50plus, configuration as70 4, suitable for simultaneous generation of electricity and heat using natural gas. The unit has never been put into operation and is in new condition. Bsdpfoz Hngmjx Anpelp At full load, the CHP unit delivers 50 kW of electrical power and approximately 104 kW of thermal power. The unit is designed for 400 V and 50 Hz and is equipped with a Liebherr G924 natural gas engine and a Leroy Somer LSAH 44.3 generator. Technical specifications: • Manufacturer: 2G Energietechnik GmbH • Type: g box 50plus • Configuration: as70 4 • ID number: H1214 • Year of manufacture: 2022 • Electrical power: 50 kW • Thermal power: approximately 104 kW • Rated voltage: 400 V • Rated frequency: 50 Hz • Rated current: 72 A • Weight of CHP module: approximately 2,200 kg • Fuel: natural gas • Electrical efficiency: approximately 34.5 percent • Thermal efficiency: approximately 71.8 percent • NOx emissions: less than 125 mg per Nm³ • Sound pressure level of CHP: approximately 55 dB(A) at 1 meter The offered package consists not only of the CHP module. The installation also includes two Viessmann boiler bodies, one Viessmann Proflame VM IV 3 gas burner, a separate control cabinet, and various flue gas components, fittings, and related documentation. The original new price of the complete installation was approximately €189,000. The installation comes from a project for which it was ultimately not used. The various main components are from 2022 and have been stored without being put into operation. Due to the size and composition of the installation, we advise interested parties to contact us in advance for further technical information, photos, documentation, and an overview of the components available. An inspection is, of course, possible (location: Winterswijk, Netherlands). Loading onto the buyer's transport vehicle is possible on site.

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6125, We sell a used CEVISA beveling machine CHP-60G INV, MFG 2024, SN: 6125 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimeters, maximum consumption of the machine: max. 15A. Electric box with: thermomagnetic switch trip +emergency stop button, net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X, and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Electrical box: with under-voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Bljdpfx Anov Ef Ryepop Price: 28.000 Euro + VAT, negotiable, FCA Oradea/Romania Irrtum, Änderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: ready for operation (used), Year of construction: 2016, operating hours: 40,000 h, functionality: fully functional, rotational speed (min.): 1,514 rpm, rotational speed (max.): 1,514 rpm, total height: 1,625 mm, total length: 2,427 mm, total width: 994 mm, overall weight: 1,800 kg, type of cooling: water, number of cylinders: 4, cubic capacity: 4,580 cm³, torque: 341 Nm, protection type (IP code): IP54, For sale are 4 x 2G G-Box 50 cogeneration units in a soundproof enclosure. The units are fully functional and have been regularly serviced throughout their operational period in accordance with the manufacturer's service protocol, using original spare parts. Details: Manufacturer: 2G Model: G-Box 50 Quantity: 4 units Design: soundproof enclosure Engine age: 10 years Blsdpfx Anoz I Nakopop Operating hours: approximately 40,000 hours Condition: fully functional and regularly serviced The set includes all necessary equipment for the operation of the cogeneration unit (CHP), including the electrical cabinet, control system, and all other required components. The units are ready for transport. Price: 10,000 EUR/unit

Condition: good (used), Year of construction: 2021, total width: 500 mm, total length: 800 mm, total height: 500 mm, overall weight: 65 kg, sheet thickness (max.): 40 mm, operating speed: 2,600 mm/s, Cutting machine CEVISA - CHP-12 MACH-ID 9406 Make: CEVISA Type: CHP-12 Year: 2021 Max. nominal thickness 40 mm Max. recommended thickness 20 mm Max. bevel length in several runs 18 mm Max. bevel length in single run 12 mm MIn. bevel inner diameter 100 mm   X Bevel K Bevel V Bevel Y Bevel Bjdpfjzcng Asx Anpelp High average cutters lifespan around 1000 M Self feed Zero maintenace Min. Beveling angle: 22.5° Max. beveling angle: 45° Min. plate thickness: 4mm Maximum sheet thickness:40mm Power: 3 HPkW Feed rate: 2600mm/min. Length: 800mm Width: 500mm Height: 500mm Weight: 65kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2013, total width: 500 mm, total length: 800 mm, total height: 500 mm, overall weight: 65 kg, sheet thickness (max.): 40 mm, input voltage: 3,000 V, operating speed: 2,600 mm/s, Cutting machine CEVISA - CHP 12 MACH-ID 9404 Make: CEVISA Type: CHP 12 Year: 2013 Max. nominal thickness 40 mm Max. recommended thickness 20 mm Max. bevel length in several runs 18 mm Max. bevel length in single run 12 mm MIn. bevel inner diameter 100 mm Bledpfxszcngce Anpep   X Bevel K Bevel V Bevel Y Bevel High average cutters lifespan around 1000 M Self feed Zero maintenace   Min. Beveling angle: 22.5° Max. beveling angle: 45° Min. plate thickness: 4mm Maximum sheet thickness:40mm Power: 3 HPkW Feed rate: 2600mm/min. Length: 800mm Width: 500mm Height: 500mm Weight: 65kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2005, operating hours: 140,000 h, functionality: limited functionality, Name: Used CHP Unit Manufacturer: Köhler / Ziegler Type: SY 53 GSM Bedpfx Aowyax Tonpjlp Year built: 2005 Generator: Leroy Somer Generator Type: LSA 44.27/4 Generator kW: 132 kVA Fuel type: Sewage gas Electrical power: 53 kW Thermal power: 87 kW Driving force: MAN E0836 E302, 6 Zylinder, 56 kW Dimensions: L 3600 x W 950 x H 1750 mm Empty weight: 2200 kg Technical doc.: Yes Message: The Engine was changad in 2013 Condition: Used Price: On demand

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, total length: 69,000 mm, total width: 16,000 mm, total height: 16,000 mm, The system was designed according to Eurocode EN 1993 for the industrial drying of wood chips, sawdust, or similar biomass products and is suitable for use in biomass, wood, or pellet production. Process components: Air heater, deflection rollers, feed modules, discharge modules, trough chain conveyor, belt tensioning and adjustment device, 7 exhaust stacks (height up to approx. 17.6 m) Designed for hot air or waste heat utilization (e.g., biomass boiler or CHP plant), heat requirement 10,270 kW th, installed electrical power 690 kW el. The inlet temperature in the dryer is 68°C, the outlet temperature is 42°C, and the heat transfer medium is a water/glycol mixture. The volume flow at the dryer outlet is 1,081,000 m³/h. Dust emission value 5 mg/Nm³ (moist), sound pressure at a distance of 1 m 85 dB(A) from the opening of the exhaust duct and the dryer. The dryer is designed for an outside temperature down to -40°C, the conveying capacity is at least 70 m³/h and a maximum of 250 m³/h with a bulk density of 260 kg/m³. The working platform of the dryer is located on approximately 8.00 m high steel supports and is enclosed with thermally insulating sandwich panels. A hall or other production components can be inserted under and between the supports (see under Documents, Steel Structure). Bledpfezw Apgox Anpsp The system has been disassembled and stored by an experienced assembly team, and this team can be arranged for transport and reassembly. Please note: We are selling exclusively this belt dryer and no other parts! Please direct your inquiries via WhatsApp to Mr. Sörgel; he is on-site at the factory and may not always be available by phone. Thank you very much!

Condition: like new (used), Year of construction: 2022, functionality: fully functional, fuel: liquefied natural gas (LNG), - 1x CHP unit - As new - Control cabinet still in original packaging - Located in Genthin Bljdpfx Anezazraspop We are selling a CHP unit in as-new condition. It has never been used, and the control cabinet is still in its original packaging. It has never been used but has been regularly maintained and is fully functional. The CHP unit is located in Genthin and can be inspected at any time.

Year of construction: 2014, operating hours: 59,436 h, condition: used, functionality: fully functional, machine/vehicle number: 100010336, Buderus Loganova EN20 CHP Unit, 19 kW electric / 38 kW thermal For sale is a Buderus Loganova EN20 combined heat and power (CHP) unit manufactured in 2014. The unit comes from a commercial property in 70567 Stuttgart and is being decommissioned due to an upgrade of the energy supply. Since commissioning, the CHP unit has been regularly serviced as part of a premium maintenance contract. A documented service history is available. °°°Technical Data:°°° * Manufacturer: Buderus * Type: Loganova EN20 * Serial Number: 100010336 * Year of Manufacture: 2014 * Electrical Power: 19 kW * Thermal Power: approx. 38 kW * Fuel: Natural Gas * Fuel Power: 35–56 kW * Electrical Operating Range: 9.5–19.0 kW * Supply Voltage: 400 V * Rated Current: 36 A * Rated Frequency: 50 Hz * Pre-fuse: min. 63 A * Gas Inlet Pressure: 20–65 mbar * Max. Supply Temperature: 85 °C * Max. Operating Pressure: < 6 bar * Device Type: B23 * Protection Class: IP40 * Rated Speed: 1,522 rpm °°°Operating Hours:°°° * 59,436 operating hours * 6,031 start cycles °°°Condition:°°° The unit starts and runs up properly. Currently, there is a fault in the heat exchanger. Based on initial assessment, the heating water pump is defective. The CHP unit is currently out of operation and is being offered with the corresponding repair requirements. °°°Location:°°° 70567 Stuttgart, Germany The planned decommissioning or dismantling is expected to take place between August and September 2026. Bjdpszv Sfnofx Anpelp An inspection is possible after prior arrangement. We will gladly provide additional photos, technical documents, and information on the available service and maintenance history upon request. Sale of a used technical unit in its current condition.

Condition: used, Year of construction: 2009, operating hours: 64,000 h, functionality: limited functionality, overall weight: 2,500 kg, fuel type: gas, motor manufacturer: MAN, Köhler & Ziegler MAN GAS Combined Heat and Power Plant (CHP) 54 kW - Leroy Somer Generator We are offering a Combined Heat and Power Plant (CHP) ⭐︎ Condition: The CHP unit is used but in good condition. Blsdpjy Rz N Usfx Anpsp ⭐︎ Condition: good (used) Fully operational and well maintained! Recently dismantled! The MAN E0834 E302 is a stationary natural gas aspirated engine primarily used in combined heat and power plants (CHP) for the simultaneous generation of electricity and heat. This four-stroke Otto gas engine features a compact design with four cylinders in-line. Manufacturer: Köhler & Ziegler, Germany Engine: - Manufacturer: MAN - Engine type: MAN E0834 E302 - Design: 4-cylinder in-line engine, water-cooled - 4.6 litre - 1500 rpm Generator - Manufacturer: Leroy Somer (Germany) - 90 kW - 3 phase 400 Volt - 50 Hertz - Operating hours: approx. 64,000 hours Dimensions: L:3100 mm x W: 1000 mm x H: 2000 mm Weight: approx. 2500 kg Condition: - Used – Good The generator was used in a publicly accessible building. Regular maintenance was carried out ⭐︎ Further technical data: see photos. Scope of delivery as shown Will be delivered as shown Inspection before purchase is possible and expressly encouraged. All our items are dismantled, cleaned, and visually checked for damages by our qualified personnel before sale. For all item-relevant data/information, please refer to the description and photos. All statements are made to the best of our knowledge and belief. The offered goods are sold as described and inspected. International buyers welcome Please inquire for shipping costs to Europe and overseas #2. Storage Shelf 44-1-8 Scope of delivery: - MAN GAS CHP unit 54 kW - With electrical control cabinet Shipping: - Nationwide transport within Germany is available for an additional charge - To provide an exact freight quote, please send me a request with your ZIP code

Condition: used, Year of construction: 2005, operating hours: 140,000 h, Name: CHP used Manufacturer: Köhler / Ziegler Type: SY 53 GSM Year built: 2005 Generator: Leroy Somer Generator Type: LSA44.2S7/4 Generator kW: 132 kVA Turbo: No Fuel type: Sewage gas Electrical power: 53 kW Thermal power: 87 kW Driving force: MAN E0836 E302, 6 Zylinder, 56kW Dimensions: L 3.600 x W 950 x H 1.750 mm Empty weight: 2.200 kg Technical doc.: Yes Message: The engine was changed in 2013 Condition: Second hand Price: On demand Bedpowyaxgsfx Anpelp

Condition: used, Year of construction: 2013, functionality: fully functional, 2 units available, including silencer and gas control unit. Blsdpfx Anez D S Ngopsp

Condition: used, Year of construction: 2016, operating hours: 30,000 h, functionality: fully functional, machine/vehicle number: 2212725, type of input current: three-phase, power: 1,999 kW (2,717.88 HP), input voltage: 400 V, control cabinet width: 800 mm, control cabinet length: 3,000 mm, control cabinet height: 2,400 mm, rotational speed (min.): 1,500 rpm, rotational speed (max.): 1,500 rpm, total height: 3,200 mm, total length: 16,000 mm, total width: 3,200 mm, fuel: domestic gas H, overall weight: 45,000 kg, type of cooling: water, nominal power: 1,999 kW (2,717.88 HP), nominal power (apparent): 2,000 kVA, input frequency: 50 Hz, input current: 250 A, Equipment: documentation/manual, The CHP unit is used in the horticultural operation to supply electricity. It can operate in parallel with the grid or in island mode. It is maintained by the manufacturer under a full-service contract. It is in good condition and fully functional. The container is spacious and very comfortable for service work. The generator is connected to the circuit breaker via a copper busbar system, ensuring high quality. The container temperature is controlled automatically via electric sunshades. The switch room is heated and air-conditioned. An EMI box is installed for continuous NOx measurement. A 15-meter chimney is located on the roof. A ladder for exhaust gas measurement is included. The unit is sold “as is” for pickup at the premises. The sale is due to a change to wind power generation. The service contract, valid up to 60,000 operating hours, can be taken over if desired and possible. It is a perfectly designed container, extremely spacious and solidly built! It is intended to remain in operation until December 1, 2026. If necessary, it can also be dismantled immediately. We would be happy to arrange a viewing and demonstrate its operation. Blsdpfxez D Ihfo Anpsp

Year of construction: 2025, condition: new, functionality: fully functional, Unused, brand new CHP unit with a TOYOTA 4Y engine, all-in-one design, employing a “plug and play” concept for easier and cost-effective installation, a user-friendly interface, a safety module for enhanced hardware protection, and a single-bearing generator to minimize potential engine damage. Bledpfx Aszl H Atenpjp This 20 kWe CHP unit is ideally suited for locations with a continuous demand for both electricity and heat. The key to CHP’s economic viability lies in utilizing the heat generated in conjunction with electricity production. Product location: Indop, d.o.o., Primorska 6a, 3325 Šoštanj, Slovenia.

Condition: new, Year of construction: 2016, functionality: fully functional, type of input current: three-phase, input voltage: 400 V, Equipment: documentation/manual, We are offering two new Totem 20 combined heat and power (CHP) units, as well as a new Totem 10 CHP unit, manufactured in 2016. These CHP units are from a warehouse clearance. According to the previous owner, the units are eligible for CHP subsidies, as they have never been installed. However, this must be verified independently. The TOTEM 20 generates a maximum of 20 kW of electricity and 48.5 kW of heat. The TOTEM 10 generates a maximum of 10 kW of electricity and 25.2 kW of heat. Please refer to the uploaded data sheet and operating manual for all other technical specifications. Depending on the location, the CHP units can also be delivered to Germany or Austria. The price for the Totem 10 is €6,000. The price for the Totem 20 is €7,000. The current list price for a new Totem 20 is approximately €57,000 gross, and they are being sold for around €45,000 (see photo). If you have any questions or require further information, please send us a message or call us. We offer a start-up guarantee in the form of a return policy in case of any issues, but we will not cover any costs incurred. Bjdpfsytympjx Anpjlp

Condition: ready for operation (used), Year of construction: 2013, operating hours: 7,358 h, functionality: fully functional, machine/vehicle number: 6LUD00036, travel distance X-axis: 620 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 460 mm, feed length X-axis: 620 mm, feed length Y-axis: 620 mm, feed length Z-axis: 460 mm, feed rate X-axis: 36,000 m/min, feed rate Y-axis: 36,000 m/min, feed rate Z-axis: 36,000 m/min, torque: 108 Nm, controller manufacturer: Heidenhain, controller model: iTNC530, workpiece length (max.): 500 mm, workpiece width (max.): 400 mm, workpiece height (max.): 350 mm, workpiece diameter (max.): 680 mm, workpiece weight (max.): 300 kg, total height: 3,400 mm, total length: 4,600 mm, total width: 2,700 mm, table width: 600 mm, table height: 755 mm, table length: 600 mm, table load: 300 kg, rotary table diameter: 600 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 12,000 rpm, overall weight: 8,500 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 12,000 rpm, operating hours of spindle: 5,303 h, coolant supply: 18 bar, distance table center to spindle nose: 50 mm, spindle motor power: 17,000 W, spindle nose: SK40, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, Commissioned 4/2014 C-axis table rotation 360° B-axis table swivel -50° / +110° Spindle nose - table distance 150mm Table clamping surface Ø650 Table load max. 300kg Table slots 5 x 18H7 x 100 mm Centering bore Ø50 H7 x 30 mm Workpiece size max. Ø 520 x 330 mm Machine accuracy VDI I DGQ 3441* Positioning accuracy +/-0.006mm* Axis resolution 0.001mm* *determined at a constant ambient temperature of 20°C +/- 1°C Main spindle: Main drive AC motor, direct drive Drive power (100% / 25% ED) 10.0/17.0 KW Speed range, stepless 20-12000 RPM Spindle taper SK 40 DIN 69871 Torque at (100% / ED) 63.7/108.6 Nm Axis drives: Axes X, Y, Z AC motors Axes B, C AC motors Travel speeds: Rapid traverse in axes X, Y, Z 36m/min Speed max. B-axis 25 RPM Speed max. C-axis 25 RPM Acceleration X, Y, Z 6.5m/s² Coolant system: External tool cooling via external nozzles Coolant tank 280l Operating pressure, external 0.9bar Coolant system, internal tool cooling DIN69871 Form A Operating pressure, internal coolant supply 18.0 bar Manual rinsing of the work area via an additional gun Standard accessories: - CNC control Heidenhain iTNC 530, full simultaneous 5-axis configuration -Handwheel 410 (Heidenhain) - Digital axis drives - Digital spindle drive - Scraper conveyor with discharge height 800 mm • Spindle cooling - radiators - plate cooling for spindle motor - Full protective enclosure with canopy Tool magazine VZG 65 5A from Indunorm: Number of tools 100 with a tool length of up to 320mm / Convertible to 125 tools, then only 200mm tool length is possible. Tool diameter max. 80mm Tool diameter max. 130mm (with free adjacent spaces) Tool change with double gripper -Linear path measuring system in axes X / Y / Z (glass scale) -Direct encoder in axes B / C -Temperature compensation - IR measuring probe - 3D Software - Option - iTNC 530 Kinematic-Opt • Calibration software Internal tool cooling 18 bar • Coolant tank • Internal tool cooling: 280 L DIN 69871 Form A • Double cartridge filter • Switchable filter cartridges Bledpfxez Diq Uj Anpsp • Filtration rating 10my Belt filter system PRODUCTION - LINE - RT 100 Automatic pallet changing system Loading and unloading via a linear axis system: Handling data: 100 kg (35 kg) Handling weight max. Pallet capacity: 6 pallet spaces up to 400 x 400 mm: Control: PLC control with integrated control cabinet incl. switching and control components incl. software for the automatic sequence Zero point clamping system 320 x 320 x 60 mm - Clamping via 4 clamping bolts - Axis distance 180mm - Clamping force 4x12500N - Repeat accuracy 0.005mm - Axial load max. 4000kg • Zero point clamping plate 320 x 320 -Automatic door Interface for automation and clamping systems Universal interface for automatic pallet changing systems, power chucks, and zero point clamping systems • for pneumatic clamping systems • 2-channel rotary through-feed integrated in the table • pneumatic lines routed to the outside • Pneumatic maintenance unit • Control via M commands logical inputs/outputs prepared incl. 12 pallets 320x320 !!without tool holders and without tools!! WITHOUT clamping devices such as vises, etc. !! Machine ex works, without delivery and assembly, all information without guarantee, price plus legal value-added tax.

Condition: used, Year of construction: 2023, functionality: unexamined, machine/vehicle number: MTU 12V4000 L33, type of input current: three-phase, total height: 5 mm, total length: 25 mm, total width: 3 mm, type of cooling: water, Equipment: documentation/manual, rotational speed infinitely variable, Plant assembled and NEVER put into operation Cogeneration Unit MTU 12V4000 L33 GAS GENERATOR SET Condition: New – 0 hours Enclosure: Enclosed container Rated electrical power: 1,262 kW Thermal power: 1,355 kW Electrical efficiency (cos φ = 1.0): 42.1% Thermal efficiency: 45.2% Total efficiency (full heat recovery): 87.3% Fuel consumption: • At 100% load: 299 Nm³/h • At 75% load: 232 Nm³/h • At 50% load: 167 Nm³/h Manufacturer: MTU – Centrica Business Solutions Srl Equipment designation: Type: E1265 250 Nox L33 Natural Gas CHP Unit Configuration: Containerized Bjdpfxjydqlqs Anpelp Rated current: 1,935 KVA Engine: Genset Rolls Royce MTU 12V4000L33 Number of cylinders: V12 Max engine power: 1,320 kW Generator: Stamford Model: PE734E-312 Type: Three-phase, synchronous, four-pole, brushless Rated voltage: 400 V Frequency: 50 Hz Dimensions (L x W x H): 12,800 / 2,700 / 2,900 mm Absorption Unit CARRIER 16LJ-F41 Condition: New – 0 hours Enclosure: Enclosed container Capacity: 1,178 kW Cooling System Flow rate: 56.4 L/sec Pressure: 45 kPa Connection (DIN): 8” (inch) Volume: 0.48 m³ Heat Rejection System Flow rate: 93.1 L/sec Pressure: 117 kPa Connection (DIN): 10” (inch) Volume: 1.39 m³ Dimensions (L x H x W): 5,330 x 3,080 x 1,690 mm Weight: 13,700 kg Evaporative Cooling Towers: No. 2 Condition: New – 0 hours

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, fuel type: gas, output current: 178 A, output voltage: 6,600 V, output frequency: 50 Hz, continuous power (apparent): 1,976 kVA, motor manufacturer: MWM Deutz, 4 units: Engine: MWM Deutz TBDG 441 BV16, dual fuel, gas, diesel, year 1993. Blodpfx Aey Hmhbonpsp Spare parts also available for sale, including turbochargers, injection pumps, cylinder heads, crankshafts, etc. 2 units: Generator: AVK 6600V 173A 50Hz, control unit.

Year of construction: 2012, operating hours: 4,000 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 363/15862010, The rotary bed dryer WB-T (model 1.00 / 3.00) from Allgaier Process Technology GmbH is a specialized industrial plant for the continuous, uniform, and gentle drying of bulk materials and biomass. In process engineering, the model designation (1.00 / 3.00) typically refers to the dimensions of the drying area, i.e., a bed width of 1.00 meter and a bed length of 3.00 meters. Blodpfxjz Rz Dnj Anpsp The heating capacity is 250 kW and is powered by electricity. Typical applications: • Biofuels & wood industry: Drying of wood chips, sawdust, and bark for pellet production. • Waste management • Agricultural & recycling industry: Processing of fermentation residues (from biogas plants), green waste, sugar beet pulp, or bagasse. Operating principle: The technology combines the process engineering advantages of a drum dryer with those of a fluidized bed dryer: • Rotary bed mechanism: The wet product lies inside on a perforated flow bed (perforated sheet). A targeted mechanical movement or tumbling in combination with the airflow creates a rotating or rolling product movement ("rotary bed"). • Counter-current or cross-current ventilation: The drying air is blown from below through the sieve bed and flows intensively through the tumbling product. This ensures an optimal heat and mass exchange. Main features & advantages: • Low-temperature drying: The plant is ideally designed for operation with waste heat or low-temperature heat sources (e.g., from combined heat and power plants/CHP or industrial residual energy). • Long residence time: This enables particularly gentle dewatering of the material while simultaneously ensuring high homogeneity of the residual moisture. • Robust particle processing: In contrast to pure fluidized beds, large, irregular, or sticky particles can also be processed economically. • Integrated screening: The flow effectively reduces fine dust and sand content during the process.

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, overall weight: 4,000 kg, fuel type: gas, power: 80 kW (108.77 HP), continuous power: 80 kW (108.77 HP), total length: 3,500 mm, total width: 800 mm, total height: 2,000 mm, motor manufacturer: MAN, CHP plant / Combined heat and power plant with MAN gas engine – manufactured in 2016. For sale is a combined heat and power plant (CHP) with a MAN gas engine and an APROVIS heat exchanger. Technical data: * Heat exchanger manufacturer: APROVIS Energy Systems * Year of manufacture: 2016 * Heat output of heat exchanger: 32 kW * Engine: MAN gas engine * Robust industrial design * Ideal for energy and heat generation Blsdpeznn Aaofx Anpjp The system is suitable as a source of spare parts, for refurbishment, or for continued industrial use. Condition: Sold as shown in the pictures. Inspection possible by appointment. Electricity: 50 kW. Heating: 80 kW.

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: KOG 130, output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, nominal power: 150 kW (203.94 HP), continuous power: 130 kW (176.75 HP), rotational speed (max.): 1,500 rpm, motor manufacturer: MAN, type of cooling: water, A cogeneration plant on wood biomass KOG130_00 with equipment was designed to convert solid fuel into gaseous fuel. In the process, the produced gas is cleaned and cooled, after which it is forwarded to the internal combustion engine of the cogeneration plant. For solid fuel, natural wood chips of class G50-G100 are used. CHP line is equipped with containerized MAN UPB -L-W-E3262E302 Woodgas genset. Bsdpfsywgp Hjx Anpelp

Condition: used, Year of construction: 2008, Name: Used CHP Unit Manufacturer: SEnergie GmbH Type: G6.12TI Year built: 2008 Generator: NEWAGE STAMFORD Generator Type: UC.I274D2 Generator kW: 100 kW Fuel type: Sewage gas Electrical power: 80 kW Thermal power: 123 kW Efficiency: 88,9 % Dimensions: L 3.500 x W 1.100 x H 2.500 mm Empty weight: 3.000 kg Technical doc.: Yes Bljdpfx Anoy Am Rnjpep Message: In 2018 a new engine was installed and the generator was rewound. Last service on October 15. 2021 with 86.102 hours. Accessories: A switch cabinet Condition: Second hand Price: On demand

Condition: used, functionality: fully functional, type of input current: three-phase, input voltage: 400 V, filter area: 324 m², suction capacity: 18,000 m³/h, negative pressure: 2,250 Pa, input frequency: 50 Hz, Dust extraction, filtration, welding fume extraction, self-cleaning cartridge filter, pneumatic, vacuum-based TEKA AIRTECH P18. The main areas of application for these systems are industrial plants/welding shops where it is not possible to implement point extraction or where point extraction is not sufficient to maintain clean air in the workshop. Laterally mounted ducts with a pollution collection point draw in contaminated air and lead it to the filtration section. Here, pollutants in the form of fine particles accumulate on the surface of the cartridge filter. A compressed air pulse is applied to clean the cartridge filters automatically at the required intervals. After the compressed air pulse, the particles collected on the filter surface detach and fall into the dust collection tank. The cleaned air returns to the work area through individually adjustable long-range nozzles. At the same time, the outlet of the cleaned air directs the contaminated air in the workshop towards the extraction ducts. The filter is cleaned by a microprocessor controller with compressed air pulses during operation, resulting in high device efficiency. Low compressed air consumption thanks to the "Power-Spray" system. The AIRTECH series of devices is certified by IFA according to EN ISO 15012-1 or DIN EN ISO 21904-1/-2 and approved for welding fume class W3 as a stationary, local welding fume extraction unit. Parameters: Capacity - 18,000 m3/h Motor power - 11 kW Vacuum - 2250 Pa Bodj Ahm Iiepfx Anpolp Filtration area - 324 m2 (9 filter cartridges of 36 m2 each) Fan in a sound-absorbing housing Control cabinet with electrical documentation Noise level - 72 dB Dimensions: Height - 5.00 m Base width - 1.44 m x 1.44 m Width with outlet ducts - 8.5 m Total weight approximately 2400 kg