Horizontal Machining Centre

Okuma MA-400HA + 6APC

Condition: used, Year of construction: 2007, operating hours: 20,000 h, functionality: fully functional, travel distance X-axis: 560 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 625 mm, nominal power (apparent): 49 kVA, controller manufacturer: Okuma, controller model: OSP-P200M, table width: 400 mm, table length: 400 mm, table load: 400 kg, spindle speed (min.): 50 rpm, spindle speed (max.): 15,000 rpm, operating hours of spindle: 58,000 h, coolant supply: 30 bar, spindle motor power: 22,000 W, spindle nose: SK40 Big Plus, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, pallet changer: automatic, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Well-maintained 3-axis Okuma MA-400HA horizontal machining center for sale The Z-axis module requires an overhaul. If more than 30% of the maximum rapid traverse speed is selected, the axis does not move. The machine is still in daily production and can be inspected at any time. The machine is offered including: - 100 SK tool holders (without tools) included Hjdpfx Aoyvga Ued Rsfg - Renishaw OMP60 measuring system incl. probe and module (for tool breakage control and tool length measurement via mechanical touch sensor) - Expanded control options (larger storage for offsets, tool corrections, axis mirroring, manual measurement, scaling up/down) - DNC-DT interface - 30 bar through-spindle coolant supply - 6 pallets incl. fixtures for machining round parts. Smallest fixture diameter 160mm, largest fixture diameter 370mm - Mayfran Consep 2000 II chip conveyor including nonwoven-free coolant filtration system

Condition: used, Year of construction: 2014, Industrial robot Hfodpfx Adoxuwlwe Rog Manufacturer: Kuka Model: KR210 R3100 ultra with 4.5m linear axis Year of manufacture: 2014 Reach: 3,196 mm Weight: 1,154 kg Payload: 210 kg Kuka Controller KRC4 Year of manufacture: 2014 Weight: 163 kg Software: KSS 8.5.4 Kuka TouchPad KCP4 Kuka connection cables Kuka linear axis Type: KL1500-3 T Year of manufacture: 2013 Length approx. 4.5 m Travel path approx. 3.5 m KRC4 cable drag chain Weight: 2,200 kg

Year of construction: 1976, condition: good (used), strip width: 300 - 1.350 mm strip thickness: 0,35 - 3 mm Hodpjbh Ubwofx Ad Rsfg coil weight: 12,5 t mandrel Ø: 508 mm

Condition: good (used), Industrial robots Manufacturer: Kuka Model: KR6, KR6-2, KR6arc Model: KR16L6, KR16L6-2, KR16, KR16-2, KR16-2 S, KR16-2 F All models equipped with KRC2ed05 control system Kuka KR6 KRC2ed05 Year of manufacture 2006 Kuka KR6-2 KRC2ed05 Year of manufacture 2011 Kuka KR6arc KRC2ed05 Year of manufacture 2006-2007 = several units in stock Kuka KR16L6 KRC2ed05 Year of manufacture 2009 Kuka KR16L6-2 KRC2ed05 Year of manufacture 2011 Kuka KR16 KRC2ed05 Year of manufacture 2007-2009 = several units in stock Kuka KR16-2 KRC2ed05 Year of manufacture 2010-2012 = several units in stock Hfedpfx Adetuc U Ro Rsg Kuka KR16-2 Speed KRC2ed05 Year of manufacture 2012 = several units in stock Kuka KR16-2 Foundry KRC2ed05 Year of manufacture 2012

Condition: ready for operation (used), Year of construction: 2011, operating hours: 35,044 h, spindle speed (max.): 10,000 rpm, total height: 3,000 mm, total width: 2,500 mm, overall weight: 11,000 kg, travel distance X-axis: 850 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 500 mm, controller manufacturer: SIEMENS, controller model: 840D, spindle motor power: 16,800 W, product length (max.): 2,500 mm, table load: 500 kg, tool weight: 8,000 g, number of slots in tool magazine: 82, number of axes: 5, This 5-axis HERMLE C40U Dynamic universal machining centre was manufactured in 2011. It features a travel of 850 mm in the X-axis, 700 mm in the Y-axis, and 500 mm in the Z-axis. The machine has a maximum spindle speed of 10,000 rpm and a magazine capacity of 38 positions plus 43 additional. If you are looking to get high-quality machining capabilities, consider the HERMLE C40U Dynamic machine we have for sale. Contact us for further details. • Utilization: 70% • Shifts: 2 • Operating hours: 35,044.4 h • Rotary table diameter: 420 mm • Clamping surface diameter: 420 mm • Spindle: • Power at 40%: 1500 rpm = 25 / 16.8 kW; 10,000 rpm = 7 kW • Torque at 40%: 1500 rpm = 159 / 107 Nm; 10,000 rpm = 6.7 Nm • Tooling/magazine: • Number of revolvers/magazines: 2 • Magazine capacity: 38 positions Hfsdpfjy Al Ufsx Ad Rjg • Additional magazine + 43 positions • Maximum tool length: 300 mm • Maximum tool diameter: 140 mm • Knoll Cooling • Renishaw OMP 40 probe • IKZ (inner cooling through spindle) • Laser beam monitoring • Chip conveyor • SK 40 • Operating voltage 400 V/3~ • Mains frequency 50 Hz • Control voltage 24 V- • Total nominal current 60 A • Total performance 41 kVA Additional equipment • OPTIONAL for an additional charge: Tooling package available: approx. 530 tools • OPTIONAL for an additional charge: Zero-Point Clamping SystemMachine was maintained in 2025 by HERMLE officialIn August 2025, the spindle head was replaced and the geometry was checked and adjusted again by HERMLE official Technical Specification Taper Size SK 40

Condition: used, Year of construction: 2003, pressure 250 t Hfodpevuun Tjfx Ad Reg stroke 20 - 190 mm no. of strokes 25 - 140 /min throat 460 mm passage to the back 590 mm dayligth 690 mm table surface area 1500 x 880 mm hole in the table 950 x 250 mm table height over floor 900 mm ram surface 870 x 725 mm ram adjustment 120 mm power requirement 30,0 kW Weight 32,0 t dimensions of the machine ca. 2,34 x 2,38 x 3,99 m x m x m with infinitely variable drive, light guard (make Sick), hydraulic clutch/brake combination, hydraulic overload protection in ram, automatic stroke adjustment, motoric ram adjustment, pneumatic counterbalance in ram, fix table, drawing cushion in table (20 t), motoric centralized lubrication, operator's console with two-hand operation Width between the tie rods in front 940 mm Side passage 900 mm

Condition: good (used), Year of construction: 2015, travel distance X-axis: 650 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 650 mm, 1 Horizontal machining center Hfodpfouav H Nsx Ad Rsg Make: STARRAG HECKERT, type: HEC 400D, year 2015, Control system, Siemens, type Sinumerik 840D, travel X/Y/Z = 650 x 650 x 650 mm, 2-fold pallet changer, pallet size 400 x 400 mm, NC rotary table 360x 0.001°, 80-fold tool changer, HSK 63 tool holder, spindle speed 15,000 rpm, IKZ 50 bar, belt filter, coolant temperature control, spindle cooling, chip conveyor, sound and control cabinets, operating hours 43,698, spindle hours 5,401

Condition: good (used), Year of construction: 2012, Parts shown by hand not come. Hfsdpoyw Nauefx Ad Rjg Technical details are shown on picture.

Condition: good (used), Year of construction: 2008, - Max. turning diameter over bed: 700 mm - Turning length: 1,500 mm Hodpfxjxmirgo Ad Rsfg Main spindle: - Speed range: 2,800 rpm - Enlarged main spindle: Ø 150 mm, bore: 110 mm - Drive power: 30 kW, 900 Nm - Spindle nose: Size 11 Total power requirement: 59.5 kVA Approx. machine weight: 14.5 t Space requirement approx.: 6.4 x 3.0 x 2.6 m EQUIPMENT: - 3-jaw chuck, SMW KNCS-N 400 K11 - Tailstock - Programmable CNC steady rest slide (cross slide NOT retractable) - SMW-AUTOBLOK SLU-3, self-centering steady rest, clamping range Ø 12 - 152 mm - Full clamping cylinder for partial hollow clamping, draw tube bore max. Ø 100 mm - In-process measuring system Renishaw for X-/Z-/C-axis - Programmable CNC tailstock on W-axis - Drilling/milling spindle and C-axis 0.001° - Tool changer: 80 positions Tool system: HSK-A63 - Y-axis travel +115/-115 = 230 mm - B-axis 225°, positioning in 0.001° increments - ICS / internal coolant supply for driven tools - Synchronized thread cutting with driven tools - Software for use of multifunctional tools, e.g. special tool with radially arranged indexable inserts, which can be positioned in the drilling/milling spindle at 60°, 90°, 120° and 180° positions - Software for gear hobbing for straight and helical gearing with speed synchronization of main and milling spindles - Electrostatic extraction unit - Chip conveyor - Documentation - CE marking

Condition: good (used), Year of construction: 2007, Used OKUMA lathe - Model: LT200-M TwinStar - Year: 2007 - including chip conveyor - coolant tank Hodpfx Adov S Svvj Refg - immediately available