Channel baling press

Paal Konti 325 G

Condition: used, SINGLE SHAFT SHREDDER WEIMA MODEL WLK15 MAIN MOTOR 90KW ROTOR KNIVES SIZE 50X50 (NEW KNIVES) ROTOR LENGTH 1500MM ROTOR DIAMETER 370MM Psdjtqd Ndopfx Amijpr THE MACHINE IS 100% FUNCTIONAL READY TO WORK

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Psdpfxevf E Avj Amiepr Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, power: 140 kW (190.35 HP), fuel type: diesel, overall weight: 7,490 kg, color: white, gearing type: automatic, emission class: euro6, number of seats: 3, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, The ISUZU ? Commercial Vehicle Center in Germany, with expertise, service and advice, offers you: New ISUZU NPR vehicle with ZOELLER Micro XL 7 m³ refuse collection body 3-year warranty on the chassis, valid from first registration or up to 100,000 km Standard equipment: - 5.2 litre turbo diesel engine with common rail direct injection, 140 kW / 190 hp, EURO VI OBD-D (maximum torque 510 Nm at 1,500 rpm) - Particulate filter system with DPD system and AdBlue (the self-cleaning system allows the filter to be cleaned without a workshop visit, thanks to the new DPD regeneration technology which indicates when regeneration is needed. Just press the DPD button and the system will clean itself in 20 minutes) - Automated manual transmission (NEES II) with 6 gears, torque converter, and cruise control. The integrated fluid coupling allows for wear-free and precisely metered starts! Gears can also be shifted manually in a sequential mode via the selector lever. Depending on the load, the driver can pre-select via a button whether the vehicle should start in 1st or 2nd gear.) - Power steering - Leaf spring suspension front axle (max. axle load 3,100 kg), leaf spring suspension rear axle (max. axle load 6,000 kg) - Engine brake, cruise control - ABS with EBD and electronic traction control on the rear axle (ASR) - Electronic vehicle stability control system (EVSC) - Lane departure warning system - Emergency braking assistant (AEBS) - Wheelbase 3,365 mm, traction tires 215 / 75 R17.5 - Spare wheel - Suspended driver’s seat - Dual front passenger bench, 3-seater - Electric windows, electrically adjustable and heated exterior mirrors - Electronic immobilizer, daytime running lights - CD radio with Bluetooth hands-free system - Digital EC ? control unit 4.0 (GNNS) - Fog lights - Driver and passenger airbags, headrests - Height and tilt-adjustable steering wheel, internal mirror - Central locking with remote control - Cigarette lighter, cup holders, headrests - Storage compartments in door panels and roof liner Body: PTO/Single-circuit hydraulic system complete with hydraulic pump, oil tank, piping Refuse collection body type ZOELLER Micro XL 7 m³ * Usable volume from 7 to 8 m³ * Body width 2,000 mm * Tailored for chassis with a gross vehicle weight of 7.49 or 8.5 t * Consistent lightweight construction using high-strength materials * 2 externally mounted reinforcement profiles * Front wall of container closed up to 220 mm height * Floor assembly welded to be liquid-tight * Collection container fitted directly, without intermediate frame * Low-wear guidance of the ejector blade on polymer slide blocks * Double-acting hydraulic telescopic cylinder to move the ejector blade * Material selection valve with steplessly adjustable counterpressure for the ejector blade, adaptable to various waste fractions * Ergonomically arranged operator terminal in the driver’s working area * Proven and reliable technology * Excellent maneuverability * Significantly reduced maintenance due to standard electric central lubrication (available as an option for the lifter system) * Maintenance-friendly central electrical system for high availability * Long service life of the loading trough due to construction from 4 mm thick high-wear resistant steel and 3 mm steel side walls Ppjdpfx Ash Il Haomijr * Compaction mechanism mounted on slide blocks * Safety features in line with Machinery Directive 2006/42/EC and DIN EN 1501

Year of construction: 2015, condition: excellent (used), Direct gravure type A process of coating film or Aluminium with a coating agent or laminating it with another substrate. Line water.solvent based coater plus inline solvent based laminator Pjdpfx Aewp Saujmiepr Product width: Max 1,700mm Materials: 9~50um (PET), 10-60um(CPP), 10~70m (OPP), 20~ 100um (Aluminium) Speed: 300mpm (commercial 50-250 mpm) Volume:
 max 900mm Unwinding tension: 100-1,000N 
 Unwinding diametr: max 1,000mm (3in, 6in) Winding tension: 100-1000N Drying
temperature: Max 230°C (4m x 6 Zones)

Condition: excellent (used), Year of construction: 2026, functionality: fully functional, overall weight: 2,000 kg, rotor length: 870 mm, power: 30 kW (40.79 HP), We are offering you a test machine for various waste materials. The machine us good condition Pedpfxjwy Nino Amiopr

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, power: 9.7 kW (13.19 HP), Technical data cardboard shredder: Manufacturer Presto GmbH & Co. KG Type PZA Year of construction 2007 Throughput volume 130 m³/hour Speed 37/9 rpm Motor power 7,5 / 2,2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder outside without cover 2,308 x 1,320 x 685 mm (l x w x h) Machine weight 0,45 tons Use of the systems: The PZA cardboard shredder was in use in a Dutch logistics centre to pre-shred loose, erected cardboard boxes from the returns department and then press them into bales. The cartons were fed manually onto the infeed conveyor and transported directly to the cardboard shredder by a sliding belt conveyor and shredded. The pre-shredded cardboard boxes were then transported over hundreds of metres to the baler where they were pressed. Scope of delivery: 1 piece Presto cardboard shredder (2-shaft shredder) type PZA Comments: The cardboard shredder was an elementary part of the disposal line and therefore good maintained to ensure high availability of the returns department. The machine is in good condition and ready for immediate use. The price is per piece exw. our warehouse in Siddeburen, the Netherlands. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Psdpsu Tha Isfx Amispr

Condition: excellent (used), Year of construction: 2015, operating hours: 20,331 h, functionality: fully functional, pressing force: 100 t, filling opening width: 970 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 33,000 kg, Good day, We hereby offer you, without obligation, a used, complete baling press line consisting of a baler manufactured by HSM, type VK 8818 R-FU, including conveyor technology and wire tying stations. The following technical data was taken from the manufacturer's operating manual and brochures, for which we cannot guarantee accuracy or completeness. Technical Data – Baler: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours (as of September 2025) Ppedsyz Af Eepfx Amijr Number of bales pressed: 29,020 bales (as of September 2025) Press force (main press): 1000 kN Specific pressing force: 120 N/cm² Shear edge ejector force: 121 kN Feed opening dimensions: 970 x 1,800 mm Theoretical cycle time (idle): 8.3 seconds Theoretical output capacity: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Connected load: 110 kW Total current consumption: 213 A Fusing: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Output at bulk density: 20 kg/m³: 12.86 t/hour 50 kg/m³: 32.15 t/hour Bale weights (approx. 1.2 m bale length): 650 up to 750 kg per bale, material-dependent Hydraulic oil tank volume: 2000 L HVI 46 PLC control system: Siemens S7-300 Control panel: Siemens TP 700 Baler dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Space requirement (with conveyor): 35,000 x 8,480 x 7,745 mm (L x W x H) Baler weight: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t) Additional Optional Equipment Ordered: – Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to the standard 2 x 45 kW drive, with same performance – Manual activation/deactivation of the number of wire bindings to save tying wire on non-expansive material – Shear edge ejector with 121 kN pressing force – Sensor-based wire monitoring, with baler shut-off in case of wire breakage or wire end – Bale chute – Optical warning signal, mounted on the control cabinet Condition of the Baler: The complete baling system (baler and conveyor technology) is in good, ready-to-use condition. The unit has been cleaned weekly, lubricated, and maintained according to manufacturer specifications by the operator. Technical Data – Chain Belt Conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain Belt Conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Feeder belt length: 7,000 mm Inclined belt length: 14,500 mm Gooseneck length: 1,550 mm Incline: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of Delivery: – HSM VK 8818 R-FU baler – Maintenance platform – Bale chute – Wire diverting stations – Wire spool trolleys (without wire spools) – Stadler KF 1800 chain belt conveyor – Transverse sliding belt conveyor – Pit cover from feed conveyor to pit – Second control cabinet to operate the baler from the conveyor – Machine documentation in English Delivery Time: The complete system has already been dismantled, placed into storage, and can be loaded at short notice following receipt of payment. We would be pleased if this or one of our other balers might be of interest to you. Your Service Team Mertens & Frowein GmbH

Condition: used, Year of construction: 2024, operating hours: 30 h, total height: 5,380 mm, total width: 4,170 mm, total length: 5,250 mm, RECU UZ 2000 Universal Shredder in open design. Manufacturer: Recuperma Model: RECU UZ 20000 Particularly suitable for gentle and rapid composite material breakdown. Disintegration, separation of composite materials, and volume reduction. Operating principle: - Use of flexible impact elements - Size reduction through impact effect of the input material - Crushing to various particle sizes Throughput: Hourly capacity depends on the particle size and bulk density of the material to be processed. Technical data (+/- 5%): Drive power: 250 kW approx. 1490 rpm Drive type: belt drive Auxiliary drive: hydraulic unit approx. 1.5 kW Ppedsv U Ttbepfx Amior Control: SIEMENS Frequency converter: SEW brand Drum diameter: 1900 mm Weight: 25 tons Wear plate lining HB450 Material loading via hopper Chain curtain as protection against ejection of parts Material discharge via sliding door Currently, the machine is defective. The price refers to the repaired machine. Unrepaired price: €370,000. Transport not included.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Baler Dixi 60 SLD, year of manufacture 2012 Manufacturer: Maschinenfabrik Bermatingen Ppodpfx Asybazismijr Model: Dixi 60 SLD Year of manufacture: 2012 Drive power: 7.5 kW, 400 V / 32 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Press cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film Please note: All technical data are based on the manufacturer's specifications. We assume no liability for the information provided or for possible errors. This offer is subject to change without notice, prior sale reserved, and may be withdrawn at any time. Viewings are possible by appointment. Sale is ex works, prepayment required, without warranty or guarantee.

Year of construction: 2013, operating hours: 3,707 h, condition: used, empty load weight: 7,331 kg, lifting height: 6,600 mm, free lift: 2,060 mm, mast type: triplex, construction height: 2,980 mm, fork length: 2,400 mm, fork carriage width: 1,400 mm, drive type: Diesel, load capacity: 5,000 kg, construction width: 1,510 mm, Diesel forklift Load center: 500 Fork width: 130 mm Fork thickness: 60 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Transmission: Diesel-electric Condition: Ready for use and fully functional Technical condition: Good Front tires Type: Superelastic Front tires Size: 355/50-15 Front tires Condition: 40 - 60% Rear tires Type: Superelastic Rear tires Size: 250-15 Rear tires Condition: 60 - 80% Description: Full cab with heating, lighting similar to STVO, 3rd + 4th valve up to fork carriage, working lights front + rear, rotating beacon, 2x cross lever, single pedal Sideshift, 3rd valve, 4th valve, rear working lights, front working lights, heating, full cab, full free lift, interior mirror, exterior mirror, joystick, rotating beacon, windshield wiper, single pedal, LED, seat, Pedpfx Aet Ilq Ismispr