Used parallel lathe

Sibimex CU500MT

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Dcjdpjzbqqusfx Acpsn Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 3roll 3500x140 mm prepinch, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: MG, controller model: MG, number of rollers: 3, roller (bottom) diameter: 880 mm, roller (top) diameter: 950 mm, side roll diameter: 880 mm, roller length: 3,550 mm, working width: 3,500 mm, working height: 3,950 mm, sheet thickness (max.): 140 mm, sheet thickness steel (max.): 175 mm, overall weight: 200,000 kg, total length: 8,800 mm, total width: 5,100 mm, total height: 5,775 mm, power: 200 kW (271.92 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, Hydraulic Plate Bending machine planetary pinch pyramid with prebend. model MG35140V 3 roll capacity 3500x140 mm The machine was overhauled in 2024, Capacity : Plate width mm. 3500 Plate thickness mm. 140 Capacity chart in enclosed Tech data: -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Conical plate bending with hardened contrast pad -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty -Overload safety hydraulic operation protection of the 3 rolls -High pressure hydraulic power pack with multi-pumps oil feed Djdpfx Acsyzim Ajpecn -Centralized control panel electric on wheels with joysticks and digital readouts -Emergency stop with safety system around the machine working area Rolls surface length mm. 3550 Top roll mm. 950 Side rolls mm. 880 Electric power on hydraulic unit Hp 100 + Hp 100 Voltage 380 Vac / 50 Hz Configuration & accessories installed with the machine -Hardened surface of the 3 rolls -Conical plate bending attachment , rolls tilt with contrast roller type. -Centralized operator panel with directional joysticks electric. -Digital position readout of the bending rolls. -Emergency and safety installations, certified CE -User manuals and instruction books in English -Dimension see layout drw in enclosed

Condition: good (used), Year of construction: 2001, CNC turning machine Manufacturer: OKUMA Type: LB-250T Model: OSP-U10L YEAR OF MANUFACTURE: 2001 2-axis CNC turning machine with robotic loading Description: Two-axis X-Z turning machine for short workpieces, equipped with a robotic workpiece magazine Dcjdpfx Ask Hz Iwjcpen X-AXIS: 180 mm Z-AXIS: 325 mm Spindle speed: 4500 rpm Coolant system and chip conveyor

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, turning diameter over cross slide: 270 mm, spindle bore: 77 mm, turning diameter: 505 mm, turning diameter over bed slide: 505 mm, center height: 250 mm, center width: 1,500 mm, turning length: 1,500 mm, quill stroke: 180 mm, quill diameter: 80 mm, quill travel distance: 180 mm, total length: 3,095 mm, total width: 1,100 mm, total height: 1,525 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 13 rpm, swing diameter over cross slide: 270 mm, metric thread diameter (min.): 1 mm, metric thread diameter (max.): 40 mm, metric thread steps: 29, bed width: 340 mm, Turning diameter in gap: 700 mm, rotational speed (max.): 2,000 rpm, rotational speed (min.): 13 rpm, swing diameter over bed slide: 505 mm, overall weight: 2,400 kg, rapid traverse X-axis: 1 m/min, rapid traverse Z-axis: 3 m/min, quill mount: MK 5, three-jaw chuck diameter: 250 mm, Trens SN500 Classic — Reconditioned Center Lathe, 2001 We offer this fully reconditioned Trens SN500 Classic center lathe, year of construction 2001, completely overhauled by original factory technicians to near-new condition. Machine details Djdszndb Ejpfx Acpscn Manufacturer: Trens Model: SN500 Classic Year of construction: 2001 Machine type: manual universal center lathe Control type: manual Max. swing over bed: 505 mm Max. swing over cross slide: 270 mm Max. swing in bed gap: 700 mm Distance between centers: 1500 mm Height of centers: 250 mm Spindle nose: BAJONET DIN (ISO702-III) B8 Spindle bore: 77 mm Spindle speed range: 12.5–2000 min⁻¹ (18 gears) Main motor output: 7.5 kW Max. torque: 1450 Nm Standard toolpost: 4-way toolpost, max. tool size 32×25 mm Tailstock sleeve: MORSE 5, diameter 80 mm, travel 180 mm Metric threads: 29 pitches, 0.5–40 mm Whitworth threads: 38 pitches, 1–80 TPI Machine dimensions (H×WxL): 1525mm ×1100 mm x 3095mm Weight: approx. 2400 kg (without accessories) Included accessories: 3-jaw chuck TOS Svitavy IUS 250/3-2-M1, ø 250 mm, B8 mount 4-jaw chuck Bison 4335-315-8, ø 315 mm, B8 mount Steady rest, ø 10–115 mm, with 3 friction contacts (rolling contacts available as paid option) Follow rest, ø 10–115 mm, with 2 friction contacts (rolling contacts available as paid option) Large steady rest I., ø 110–250 mm, with 3 friction contacts (rolling contacts available as paid option) Reconditioning scope All guideways ground and hand-scraped Spindle ground and reconditioned Tailstock quill ground All new bearings, including spindle bearings New gears New paint finish New plates (speed, feed, and thread charts) Machine is in excellent mechanical condition and ready for immediate use. Available for inspection. Geometric protocol available. Electronic machine manual on USB. For questions or further details, feel free to contact us by message or phone.

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, turning diameter over cross slide: 630 mm, spindle bore: 320 mm, turning diameter: 1,200 mm, turning diameter over bed slide: 930 mm, turning length: 3,000 mm, Lathe in very good technical condition, has seen very little use and was not used for machining pipes. The Poręba TPL 90/3m lathe (also listed in market nomenclature as a variant of the TPK 90 series) is a textbook example of an Oil Country Lathe / Hollow Spindle Lathe. This model fulfills all the specific criteria for machines intended for the Oil & Gas sector: • Massive spindle bore (Big Bore): This version features a spindle bore with a diameter of 320 mm (approx. 12.5 inches), allowing for easy insertion of thick-walled drill and casing pipes. • Dual chucking system: The headstock is designed for mounting two independent lathe chucks (front and rear, typically 28 inches in diameter), ensuring the pipe is clamped and stabilized at both ends of the spindle. • Optimal working dimensions: The 3m designation defines a turning length between centers of 3000 mm, which, combined with a swing over bed of 930 mm (hence the "90" in the name), allows for machining heavy-duty pipeline components. • Exceptional rigidity: FUM POREBA factory machines are renowned for their monolithic, very wide and heavy cast iron beds, which effectively dampen the immense vibrations generated during taper thread cutting. In international used machinery catalogues, this specific Poręba model is directly classified under the Oil Field Lathes category. TECHNICAL SPECIFICATIONS: Geometric parameters and machining ranges • Swing over bed: 930 mm / 36.6 in • Swing over cross slide: 630 mm / 24.8 in • Swing in gap: 1200 mm / 47.2 in • Maximum turning length between centers: 3000 mm / 120 in • Bed width: 585 mm / 23.0 in Headstock • Spindle bore diameter (Hollow Spindle): 320 mm / 12.6 in (in US nomenclature classified as a 12.5" version) • Spindle speed range: 5 – 250 rpm, or modified versions up to 710 rpm • Number of spindle speed steps: 18 Feed and thread cutting system • Longitudinal feed range: 0.1 – 12.8 mm/rev / 0.004 – 0.504 in/rev • Cross feed range: 0.05 – 6.4 mm/rev / 0.002 – 0.252 in/rev • Types of threads cut: Metric, Inch (Whitworth), Module, Diametral Pitch (DP) Tailstock • Tailstock quill diameter: 130 mm / 5.1 in • Tailstock quill travel: 300 mm / 11.8 in • Internal taper of quill: Morse No. 6 (MT6) Drive and dimensions • Main motor power: 22 kW / 29.5 HP • Overall length: approx. 5500 mm / 216.5 in • Overall width: approx. 1750 mm / 68.9 in Dedpfxjy Sf Azj Acpocn • Overall height: approx. 1500 mm / 59.0 in • Total weight: approx. 8000 kg / 17,630 lbs

Condition: used, Year of construction: 2009, faceplate diameter 3000 mm swing diameter 3500 mm turning height 3200 mm Control Fanuc Dodpjyqu Rwsfx Acpjcn type Series 320i Model A slide adjustment 1750 mm ram head dimension 300x300 mm x-axis 2700 mm Table load 30000 kg main drive motor 100 kW Tool changer 16 weight of the machine ca. 89 t dimensions of the machine ca. 8,5x6x8 m No. 1104 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm over bed: 1250 mm Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Djdsyr N N Ropfx Acpscn Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) 4-way bed machine (flat bed) LED lighting

Condition: used, Modular milling cutter Module 8 Dsdpfx Ajdklt Nocpecn 20 degrees Length 1800 mm Diameter 120 mm Inner diameter 40 mm

Year of construction: 1993, condition: ready for operation (used), Center height: 280mm, distance between centers: 2000mm, turning diameter over bed/cross slide: 570mm/365mm, spindle bore: 62mm, speed: 2500rpm, max. workpiece weight: 1000kg, bed width: 360mm. Machine dimensions X/Y/Z: approx. 4000mm/2250mm/2000mm, weight: approx. 5500kg, control: Siemens. An on-site inspection is possible. Dsdpfxoxq Eyus Acpocn

Condition: used, Year of construction: 1982, Center height: 220 mm Center width: 1250/1300 mm Dcedpovzn Itefx Acpon Swing diameter: over bed 440 mm Spindle bore: Spindle mount: Tailstock taper: 5 MK Spindle speeds: 11.2 - 2240 rpm Feeds: longitudinal/transverse 0.1-2.8/0.05-1.4 mm/rev Thread pitches: Electrical connection: 380 V, 11 kW Space required: 3400 x 1400 x 1300/1700 mm Weight: approx. 2700 kg