Radial drilling machine

Valmer TR 80/2500 SP

Condition: excellent (used), Year of construction: 2005, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, rapid traverse X-axis: 35,000 m/min, rapid traverse Y-axis: 35,000 m/min, rapid traverse Z-axis: 35,000 m/min, workpiece weight (max.): 200 kg, total length: 500 mm, total width: 400 mm, table load: 200 kg, rotary table diameter: 280 mm, Coolant system Filtration tank HR 410 Handwheel iTNC530 controller 1e owner machine X - Travel: 600mm Y - Travel: 450mm Z - Travel: 400mm A - Axis: 110° B - Axis: 360° Table Length: 500mm Table Width: 400mm Table load: 200 Table Ø: 280mm Feed rate X-Axis: 35000mm/min. Feed rate Y-Axis: 35000mm/min. Feed rate Z-Axis: 35000mm/min. Feed rate A-Axis: 10Degrees/min Feed rate B-Axis: 15Degrees/min Spindle Taper: 40ISO/Bt/Mk Power on spindle: 15kW Speeds / ranges: 18000Rpm ATC / revolver: 30 Coolant through spindle / Bar:20 Number of controlled axis: 5 Chip conveyor: Yes Coolantsystem: Yes Length: 3500mm Width: 3500mm Height: 2800mm Weight: 6600kg Lrodpsx R S Smsfx Afzeg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1997, functionality: fully functional, Model: BAS 100. Flash Butt welding Machine for Band Saw Blades. Hydraulic clamping. Annealing timer. Blade positioning device. Year of manufacture: 1997. Automatic annealing temperature control. Welding wood strip up to 100 mm. Lrsdpfxew Snpie Afzog Bimetal strip up to 80 mm. Connection: 3 x 220 V. (3 x 400V available on request) Weight: 500 kg. Dimensions (W*D*H): 1400*900*1500 mm. Instructions and packing included.

Condition: used, Year of construction: 2007, cutting width (max.): 1,060 mm, cutting height (max.): 1,060 mm, Bandsaw Kasto HBA 10×12 Year 2007 Cutting ranges: Cutting area round 1,060 mm Cutting area square 1,060 x 1,060 mm Cutting area flat 1,060 x 1,260 mm Clamping range 300 - 1,260 mm Smallest dimension to be sawn approx. Ø 300 mm Smallest cut-off length 10 mm Minimum offcut length single cut 20 mm Minimum offcut length in automatic mode 100 mm Maximum table load 50 tons Table travel 6100 mm Total drive power 20 kW Saw motor 11 kW Infinitely variable cutting speed at 50 and 60 Hz 12 - 90 m/min Automatic feed length single 2,100 mm Lsdpfx Afowk D Efszerg Clamping force of machine vice 50,000 N Saw blade dimensions 11,430 x 80 x 1.6 mm Cutting feed: infinitely variable Material feed: hydraulic Material clamping: hydraulic Saw blade guide: carbide, replaceable Saw blade tensioning: hydraulic Saw blade cleaning: with easily replaceable brush, motor-driven The offer is aimed exclusively at traders within the meaning of §14 BGB (German Civil Code) No sale to private individuals

Condition: good (used), grinding diameter: 1,600 mm, grinding length: 6,000 mm, Manufacturer: CINCINNATI Type: 60 x 216 Year of manufacture: 1970 Covex and Concave grinding 6 steady rest included 2 steady rest hydrostatic Coolant system with magnetic filter Measuring system with 5 arms caliber: Arm 1: Working area 1300 to 1600 mm Arm 2: Working area 1000 to 1300 mm Arm 3: Working area 700 to 1000 mm Arm 4: Working area 400 to 700 mm Specifications Metric US Standard Center height 787 mm Grinding diameter Ø 1574 mm Grinding length 5800 mm Grinding stone dimensions Lrsdpfx Afsvvvw Ejzsg 914 x 101.6 x 304.50 mm Grinding stone speed 1800 rpm Dimensions (estimate) Length 15100 mm Width 5500 mm Height 3550 mm Weight 120000 kg Please note: The information on this page is correct to the best of our knowledge and belief and, where possible, has been obtained from the manufacturer. The information is given in good faith but accuracy cannot be guaranteed. Accordingly, it will not constitute a representation and terms of contract. We recommend that you check all important details.

Condition: like new (used), turning diameter: 1,500 mm, MAXIMUM WORK DIAMETER : 1600 mm. MAXIMUM WORKING LENGTH : 3000 mm. Lredpsr Ui R Nsfx Afzeg DIAMETER OF LANTERN SHAFT : 83 mm. OUR MACHINE IS ACTIVE WITHOUT ANY PROBLEMS ALL REVOLUTIONS AND AUTOMATICS ARE IN VERY GOOD CONDITION

Condition: used, Year of construction: 1982, grinding length:500 mm grinding width:225 mm workpiece height:400 mm total power requirement:5,5 kW weight of the machine ca.:3,4 t Lrjdocxxtmepfx Afzog NC81 NC-control, table belt drive 100-25000 mm/min., automatic feed, electronic dressing unit 020 NC-K with RPM-compensation, coolant pump, emergency cut-off

Condition: excellent (used), Year of construction: 2014, operating hours: 66,600 h, functionality: fully functional, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, We offer you the following: Technical Data: Control: Heidenhain iTNC 530 HSCI Travel distances: - X-axis: 600 mm - Y-axis: 500 mm - Z-axis: 500 mm Main spindle: - Speed range: 20 - 18,000 rpm NC Rotary Table: - Clamping surface: 600 x 500 mm - Load capacity: 400 kg - B-axis: -5° to +110° - C-axis: 360° Tool changer: - Tool holder: HSK-A63 - Number of tool pockets: 210 positions Equipment and Accessories: - Heat exchanger for spindle and table - Active cooler for control cabinet - Direct measuring system - Full enclosure - 3D control - DMG ERGOline Control - Direct measuring systems in the NC rotary/swivel table incl. table cooling - BLUM NT laser tool measurement - Calibration arbor with tool holder - Infrared probe, Heidenhain TS 649 - Preparation for 3D quickSET - Hinged belt chip conveyor - ICS, 40 bar, 600 l tank, incl. rotating viewing window, sealing air, linear measurement systems, bed flushing Lrjdpfexgnz Tox Afzog - Rinsing pistol - Mechanical oil and emulsion mist separator - Air blast through spindle center - Mode of operation 4 - Machine preparation for handling systems, consisting of: - Automatic, lateral loading door - Electrical interface for articulated arm robot - Pneumatic control and monitoring of the zero-point clamping system - Activation/deactivation of handling system via switch on machine operator panel - Additional rinsing in the machining area included - Preparation for job management included - Operator panel arrangement on the left included - Power supply to machine table incl. 2-channel rotary union - Additional machine-side clamping hydraulics, 1 clamping circuit: - Clamping hydraulics, 1 circuit, 30 - 240 bar, pressure adjustment via proportional valve technology - Extension of rotary union to 4 channels included On-time hours: approx. 66,600 h Spindle hours: approx. 44,800 h The robot shown in the pictures is not included in the scope of delivery. The machine is expected to be available from October/November 2025. The ball screw drives and linear guides in the X and Z axes have been replaced. Accessories, depicted tools, and clamping equipment are only included if specifically mentioned in the additional information. Subject to changes and errors in the technical specifications and information. Prior sale reserved!

Condition: excellent (used), Grinding length 1000 mm Lredpfx Afok Abxxszjg grinding diameter fi 350 mm In very good condition.

Condition: good (used), Year of construction: 2000, machine/vehicle number: 13639, Control Heidenhain X-Way 1,200 mm Y-way 800 mm Z-way 500 mm Main spindle: Speed 16,000 rpm Drive power - main spindle 17 kW Spindle Tool holder Type HSK63 Spindle diameter in front. Bearing 70 mm Upgraded Tool changer Size: 100 Swing round table: Round table diameter 800 mm Swivel range A: -15 / + 97° rotatable C: 360° max. table load approx. 1,000 kg max. tool diameter 80 mm max. tool byway. with free neighbor box. 125 mm max. tool length 300 mm max. tool weight 8 kg Feeds: Rapid response ( X / Y / Z ) 30 m/min Total power requirement 31 kVA Machine weight 15 tons Space requirements approx. 6.0 x 5.0 x 3.6 m Lsdpfx Aeinh Rqofzerg other equipment - Documentation - Chip conveyors - electronic heat compensation Y- + Z-axis

Condition: good (used), Used radial drill SASS Mod.TRM 2200 Excellent condition, fully functional. Cube supplied Maximum diameter drilling from solid cast iron 20-22 100 mm Maximum diameter drilling from solid steel R=60 80 mm Sliding quill spindle diameter 102 mm Spindle morse taper 6 Spindle vertical travel 500 mm Lrjdpfx Aoikqz Ssfzjg Rotational speed 32 Spindle speed values with 50 Hz motor - rpm/1' 18 ÷ 1600 Automatic feeds Maximum reach from column edge to spindle axis 2230 mm Minimum and maximum drilling radius 660 ÷2505 mm Head displacement on arm 1845 mm Vertical arm displacement 1040 mm Column diameter 550 mm Column height with motor 3720 mm Base plate height 260 mm Base plate height 2490 x 1230 mm Spindle motor 11 HP Weight 9000 kg