CNC SCRIBING and MARKING LINE

VOORTMAN V704

Condition: like new (used), functionality: fully functional, Year of construction: 2014, operating hours: 24 h, I am selling full complete onion peeling processing line with M&P onion peelers, items are listed below: -6x M & P onion peeler machine -all conveyers, elevators for transport peeled, unpeeled and waste product -inspection table Nedpfx Agjtzmifo Iswc -all working platforms -all hoppers for row (unpeeled materials) Excluded air screw compressors but for serious enquire i could help out with additional equipment. Capacity 2700- 4500 kg /h of peeled onion

Condition: repair required (used), Year of construction: 2013, operating hours: 33,439 h, - Volvo L180G - Year of production 2013 - Mileage 33,439 Mtg Nwjdeu Ef Hropfx Ag Iec - Transmission after major overhaul - 340 mtg. - Engine compartment burnt out - condition shown in photos

Condition: good (used), Year of construction: 2000, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Machine design - Work table 1800 x 600 mm with 4T-slots - Boom travel 1050 mm - SK 40 drilling spindle with tool clamping device - Infinitely variable speed programming - Infinitely variable quill feed via three-phase servo motor - 2 T-slots 18 mm on the machine base at the rear - 2 T-slots 18 mm on the left machine base frame - Thread cutting device - Central lubrication - Coolant device - Machine light - CE marking - Safety device - USB interface Dimensions and travels Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column stroke (W-axis) mm 410 Distance spindle bottom edge - min mm 70 Table top edge max. mm 680 Distance spindle bottom edge - min mm 970 Floor max. mm 1580 Drilling radius mm 540 - 1590 Worktable height mm 900 Nsdpfxou Aa I So Ag Ijwc Cutting values Drilling capacity into solid St 60  40 GG 22  50 Thread cutting St 60 M 36 GG 22 M 42 Main spindle drive AC motor, frequency-controlled kW 5.5 at 100 % duty cycle. Speed range: min -1 15 - 2800 Torque Nm max. 250 constant from min -1 15 - 2000 Feed drives X-axis - AC - servo motor kW 0.25 Y-axis - AC - servo motor kW 0.25 Z-axis - AC - servo motor kW 4.50 W-axis - AC - servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min. 7.5 / 7.5 / 5 Rapid traverse speeds (W): m/min. 3 Feed rates stepless mm/min 5 - 2000 Accuracy Positioning accuracy X-, Y-axis to 1200 mm mm ± 0.075 Electrical data Operating voltage / frequency V / Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, easy to read from all sides legible from all sides, 215 x 160 mm Position information: Cartesian or polar, absolute or incremental measurements, Unit of measurement: mm or inch or in degrees Interpolation: 2 axes (X, Y) Technology database: tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool management: max. 500 tools Subroutine technology: yes Machining cycles Standard software options: Programming in dialog, 38 zero offsets, rotation and mirroring, teach-in for X, Y, Z, restart in program with selection functions for targeted entry Zero point determination: Cycles for determining zero points by manually probing the workpiece for by manually probing the workpiece for: - any clamped rectangular parts - any clamped round parts - Mediation of cast and flame-cut parts - Angular position detection for round parts by touching reference edges or surfaces Test graphics Graphic display of drilling patterns Data interfaces USB

Condition: new, Extraction capacity of filter unit at spigot*: 350 m³/h Total power consumption*: 0.09 kW Operating voltage: 230 V, 50/60 Hz, 1PH + N + PE Noise level*: 52 db(A) Dimensions L/W/H in mm: L 329 / W 374 /H 510 Colour: RAL 7035 Weight: 25 kg Manufacturer: ISI Industrieprodukte GmbH *Depending on the filter equipment Special voltage or special colour on request Application: Extraction of oil mist and smoke, for small to very large machine workrooms. Your advantages of the ELBARON series: - 18 unit variants available - Direct from the manufacturer - ISI-TRONIC as standard (digitalised filter control) Nwedpfx Aoh Rdwxjg Ijc - Electronically controlled EC fan as standard - Speed and air flow rate adjustable - Simplex (single-stage) or duplex (two-stage) available - Wide range of air flow rates available - Adaptable to pollutant load and air performance requirements - Large range of mounting and connection accessories - Quality Made in Germany We have developed the ELBARON® filter series for use in machining operations with pure oil or for separating oil mist and smoke. For many years now, the digital electrostatic air filters of the ELBARON® series have been among the most efficient filter units on the market and are in use worldwide. Our filter units are already digitalised as standard and can be controlled, for example, using a laptop. The ELBARON® unit series comprises 18 unit variants and can be optimally designed for your application in terms of size and performance. ELBARON® units impress with their long service life and absolute functional reliability. Our electrostatic filter cells are dimensioned in such a way that the best possible filter efficiencies, service lives and trouble-free operation are achieved under economic aspects.

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm Nwjdpfx Aohzbipsg Isc - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: used, TECHNICAL DETAILS - Number of axes : 5 - Number of spindles : 2 MAIN SPINDLE - Max. bar diameter : 20 [mm] - Max. machining length : 210 [mm] - Spindle speeds : 200 - 10000 [rpm] - Spindle power : 2.2 / 3.7 [kW] - C axis indexing precision : 0.001 [°] COUNTER-SPINDLE - Max. bar diameter : 20 [mm] - Spindle speeds : 200 - 12000 [rpm] - Spindle power : 2.2 / 3.7 [kW] - C axis indexing precision : 0.001 [°] GUIDE BUSH HOLDER 1 - Number of positions : 5 - Number of motorized positions : 3 - Live tools speed : 8000 [rpm] GUIDE BUSH HOLDER 2 - Number of positions : 3 END ATTACHMENT - Number of positions : 8 SECONDARY OPERATION - Number of positions : 4 - Number of motorized positions : 2 - Live tools speed : 8000 [rpm] POWER SUPPLY - Total installed power : 11 [kVA] WEIGHT & DIMENSIONS - Machine floor space : 1655 x 1125 [mm] - Machine height : 1700 [mm] - Machine weight : 2000 [kg] MACHINE HOURS - Number of working hours : 13.837 [h] Nsdpfx Agjuhbbzs Iewc EQUIPMENT - CNC : Fanuc Oi-TD - 3 colors status lamp - Rotating guide bush - Parts catcher - Parts conveying strip - Ejection of workpiece - Chips conveyor - Coolant tank * with high-pressure pump : 70 [bars] - Bar loader : IEMCA ELITE 220 E / 32 LL - Fire extinguisher * NB : working order not guaranteed. To have it checked by a qualified organization of the buyer. - Electric transformer

Condition: refurbished (used), functionality: limited functionality, Year of construction: 2003, operating hours: 24,000 h, pipe diameter (max.): 100 mm, pipe length (max.): 4,100 mm, bending angle (max.): 183 °, bending radius (max.): 300 mm, wall thickness: 8 mm, Transfluid DB 2090 DB CNC Mandrel Tube Bending Machine. Excellent High Quality Germany Machine, with fully refurbished main hydraulic pumps and main head fully reconditioned. Only requires new encoder to be fitted and this machine is ready to go. Features include. 100mm x 1.6mm Tube Maximum Capacity at 1.5D Anticipated Mandrel Withdrawal Fully automatic setup of clamps and follower Boosted Follower for tight radius thin wall tube bending. Long bed with 4000mm over mandrel. Comes with huge amount of tooling worth over AU$150k. Tooling Included: 101.6mm 152mm CLR 101.6mm 200mm CLR 76.2mm 114mm CLR 76.2mm 200mm CLR Nwsdpfxjtrd T Ts Ag Ioc 76.2mm 238mm CLR 63.5mm 96mm CLR 57.2mm 86mm CLR 50.8mm 76mm CLR 44.5mm 67mm CLR 40 x 40 120mm CLR 50 x 50 150mm CLR 60.3mm 150mm CLR 48.3mm 120mm CLR

Condition: good (used), Year of construction: 2011, LANDIS LT-2 TWIN WHEEL CNC ORBITAL CRANK GRINDER Equipped with: Landis 6400 CNC Control Siemens TOUCH HMI Arobetech Steady Rest Marposs P7 Gage System Lateral Locator Twin CBN Grinding Wheels Rotary Dresser Headstock Tailstock Rittal AC Units Nwedpfx Aertrxxog Ioc Specifications: Maximum Center Distance: 680 mm

Year of construction: 2012, condition: good (used), Muratec MW120 GT for sale Used, in excellent condition. The machine can be viewed by appointment. Delivery is the customer's responsibility, but we can help with packing and loading of need. Delivery: EXW Székesfehérvár Nwedpsifi D Tefx Ag Ioc

Condition: new, functionality: fully functional, Fervi T047/400VDA Gear-Driven Milling and Drilling Machine with Tapping 400V 1.5kW BRAND NEW “CE” CERTIFIED Promo price – single unit available while stocks last. The machine can be used for: Milling Drilling Tapping Drilling capacity in cast iron (with pilot hole): ø 40 mm Max drilling capacity in steel (with pilot hole): ø 32 mm Milling capacity with indexable cutter: ø 80 mm Milling capacity: ø 25 mm Tapping capacity: Ø 22 mm Taper: MT 4 Quill stroke: 130 mm Quill diameter: ø 76 mm Column diameter: ø 115 mm Nedpfx Aeg Npiweg Iewc Head tilt: ± 60° Spindle speed: (12) 75 ÷ 3200 rpm Three-phase motor: 400 V 50 Hz 1.1 – 1.5 kW Table dimensions: 585 x 190 mm T-slot: 12 mm Base dimensions: 648 x 412 mm Overall dimensions: 740 x 790 x 1960h mm Weight: 390 kg.