Condition: new, Year of construction: 2025, Functionality: fully functional, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece width (max.): 500 mm, workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, Scope of delivery: 1. chemical pre-treatment by spraying (in cycle process) 2. dryer 3. powder coating system 4. single powder oven Celrar Ejulwg Nedjgt 5. conveyor technology, semi-automatic 6. electrical control system Hall/ floor space Floor area of the system max. 12,000 x 6,500 mm Hall floor Industrial floor Workpiece sizes Max. Part dimensions L= 500mm, H= 1,500mm, W= 500mm Range of steel parts Conveyor technology P&F chain conveyor in cycle mode, semi-automatic Pre-treatment Chemical Power supply Electricity On-site power (max. 88 kW) Gas On-site power Compressed air On-site power Water On-site power Calculation Type of system Cycle system Conveying speed 3.2 meters / min Length per cycle L = 1,600 mm Time for cycle movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minute Time for cycle standstill: Ts = 8.5-12 minutes Total time for cycle Tt = Tm + Ts = 9-12.5 min Electrical energy: Total power 88 kW min. Average consumption 60 kWh max. average consumption 70 kWh

Condition: ready for operation (used), Dust Cyclone, Dust Separator, Dust Extractor, Abrasive Celrevr U Etear Edegt Overall dimensions: 1900 x 1500 x 2200 mm Inlet diameter ø: 200 mm Outlet diameter ø: 250 mm Cyclone diameter ø: 1230 mm Cyclone body height: 630 mm

Condition: new, Year of construction: 2024, Povder sieve Model SV-200 Screen type stand Mesh 149 µ External dimensions 700 x700 x1200mm 220-240V voltage Celrarjbwh S So Edogt Power Consumption 40W Performance ~ 20kg/5min Frequency of 50Hz Tank with fluidisation

Condition: refurbished (used), Year of construction: 2000, Functionality: fully functional, WE REPAIR ALL TYPES OF BLASTING WHEELS!!! Unbeatable prices!!! We offer right and left blasting - blasting unit, blasting wheel after general repair. Blasting unit with a blasting wheel from the manufacturer Škoda type - MZ320 Cslrarjivg I Ts Edjgt for blasting machines of the following types: Škoda -TTP1 Škoda -TTP1-A Škoda -TTP1 Škoda -TMSO2,4 Škoda -TS2000 Škoda -TTP63 The price is for 1 piece. Blaster, blasting, blasting, sandblasting, blasting, sandblasting. Blast machine.

Condition: as good as new (ex-display), Year of construction: 2024, operating hours: 30 h, Functionality: fully functional, input voltage: 230 V, laser power: 100 W, type of cooling: air, overall weight: 16 kg, laser wavelength: 1,064 nm, For sale is a barely used laser cleaning machine from P-Laser, produced in Belgium. Using state-of-the-art laser technology, YOU are able to remove coatings and dirt from all precious and base metals, as well as (natural) stone, wood, concrete and many other surfaces, without causing any damage. Laser cleaning is revolutionizing various industries with advanced laser cleaning technology - from the precise removal of coatings in production to the restoration of vehicle parts. The versatile applications not only offer outstanding results, but also open up the opportunity to increase efficiency and sustainability. Cjlevn Sw Eorar Edegt Laser cleaning is defined as the innovative process of removing unwanted material from solid surfaces using a laser beam. The powerful energy absorption of the laser beam heats the target material quickly, causing it to either evaporate or sublimate. What is fascinating is that the surface underneath remains untouched by this energy. By specifically adjusting the laser characteristics and the pulse length, this advanced technology enables precise control of material removal with previously unattainable accuracy. Laser cleaning is therefore not only perfect for quickly and thoroughly removing rust, but also for removing a very thin layer of paint without affecting the primer. Discover the future of surface treatment with our innovative laser cleaning technology - for a flawless surface without compromise. The laser offers an innovative, ecological, efficient and highly mobile cleaning solution for almost all surfaces, both in industry and in trade and commerce. The machine can be inspected and tested, with a purchase inspection by the manufacturer on request. Net invoice possible. The scope of delivery includes not only the laser with 4 different lenses in an extremely robust transport case, but also 4 laser safety glasses and a folding screen for shielding.

Condition: excellent (used), Year of construction: 2001, Functionality: fully functional, total height: 2,450 mm, total length: 2,100 mm, total width: 1,580 mm, overall weight: 130 kg, working width: 1,500 mm, filter area: 2.1 m², total depth: 2,100 mm, Equipment: cabin, For sale is a very well-preserved paint booth from the manufacturer Lung. The machine is only being sold because it is no longer in operation. The machine is ready for immediate use and assembled ready to plug in, see pictures. The extraction area is 1.50 x 1.40m. The external dimensions are 2.45m high, 1.58m wide and 2.10m deep. The front part of the paint booth consists of two tubs that are filled with water. The rear part has a filter mat that needs to be replaced occasionally. Cslrsvzlm Tsar Edjgt

Condition: new, Year of construction: 2025, 1. powder coating oven 1,500 x 1,200 x 1,750 mm 2. powder coating booth -KG DUO-01 3. powder coating system Wagner, - Prima Sprint - Cgsljfhxd Uorar Edot 1. powder coating oven 1,500 x 1,200 x 1,750 mm 1 Internal dimension length 1,500 mm 2 Internal dimension width 1,200 mm 3 Internal height 1,750 mm 4 External dimension incl. thermoblock length 2,250 mm 5 External dimension incl. thermoblock width 1,815 mm 6 External dimension incl. thermoblock height 2,006 mm, 2,296 mm incl. exhaust air pipe 7 Substructure 1 set of steel profiles 8 Walls 1 set of 1 mm galvanized sheet metal on both sides, RAL outside 9 Insulation walls, ceiling 1 set rock wool 150 mm, floor is insulated with 50 mm 10 Oven floor with 2 run-in rails for rack trolleys 11 Temperature 220°C 12 Fans 1 unit 2,600 m³/hour 13 Electric motors 1 pc. 1.1 kW, 1450 rpm, 3 F, 50 Hz 14 Thermal output 14 kW 15 Hinged doors on one side 2 insulated with 100 mm rock wool Indirect heating via thermoblock Thermoblock 1 set stainless steel INOX AISI 316 Heating electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 16 burners 1 oven is electrically heated 1 exhaust air 1 piece device for exhaust air pipe, manual flap guide 2. powder coating booth -KG DUO-01 The overspray during powder coating is collected by the extraction unit. The workpieces are hung on a hook in the booth. - The extraction unit is equipped with a 30 l powder container (rollbar). - There are 2 filters in the extraction unit as the 1st stage. - The 2nd stage in the extraction unit is the high-pressure fan. 1 Dimensions of the powder stand Width 1,200 mm Depth 1,100 mm Height 2,380 mm 2 fans 1 pc. 2,500 m³/hour, 1,500 Pa Electric motor 1.1 kW, B5, P2, 380 V 3 Filter Φ 325x600 2 pcs. type filter cartridges 4 Electromagnetic valves 1 pc. 1" "Turbo" Italy 5 Illumination 1 pc. 2x18 Watt= 36 Watt 3. powder coating unit Wagner, - Prima Sprint - 1 Dimensions of the Prima Sprint Depth 725 mm Width 480 mm Height 1.100 mm Weight Approx. 39 kg Mains standard 230 VAC Frequency 50 - 60 Hz Inlet compressed air 6-8 bar Outlet compressed air 0.05 - 5.5 Nm³/hour - Corona hand gun PEM-C4 Ergo - EPG-Sprint control unit - Delivery device with fluid crown ST 550/10 - Powder injector PI-F1 - Equipment cart with vibrating table

Condition: new, Year of construction: 2025, Functionality: fully functional, INDUSTRIAL POWDER COATING FURNACE (WITH PALLET TYPE CONVEYOR) - Length:600cm Width:200cm Height:300cm (Net Usage Area is 260/270cm) - Fuel Gas - Burner: Ureth Brand / URG Series - Thermoblock All 2mm 304 Quality Stainless Steel - Body All 1/1.2mm Galvanized (DKP - Black Sheet Not Used) - Circulation Fan Motor (2 pcs) - Conveyor (Pallet Type) - Electric Panel: Control Unit (Programmable.) - Insulation: Brand Knauf German Made Rock Wool (15cm) INDUSTRIAL POWDER COATING BOOTH (6 FILTERS) - Length:400cm Width:120cm Height:250cm (Net Usage Area) - 6 Filters Included. - Works with Solenoid Valve System. - LED Illuminated. - Top Manual Rail System. - Electric Panel: Control Unit ELECTROSTATIC POWDER COATING MACHINE (2X) Cgjlrajlwqvdjr Edet - Manual System - Powder Coating Tank Included.

Year of construction: 2019, Condition: new, Gravitation - Rim - Oven ( without circulating air ) Cgolsc Nbkcjrar Edst Model SLS - 18/27 1 - 27 kW (stepless power regulation) * Available immediately - June/July 2017 Inside BHL: 1200 x 1700 x 2000 , Outside : 1400 W x 2060 H x 2200 D Insulation thickness: 80 mm, Heating time 15-40 minutes up to 180°C Max. Max. temperature 230°C Type of air distribution gravitation Volume 5400 L Transport: trolley Gravitation heating system - low operating costs, trouble-free Explosion-proof locks comply with PN-EN Automatic control system Changes and Errors in technical data, information and prices and subject to prior sale.

Condition: new, Functionality: fully functional, Year of construction: 2025, Powder Coating Booth + Manual Powder Coating Spray Gun Height:250cm The number of filters is increased according to the project Advantages of the Paint Booth The use of paint booths offers many advantages to businesses High Paint Quality: Working in an environment protected from dust, dirt and other external factors results in a smoother and more aesthetic surface. Cslrarsv Nvkfo Edjgt Energy Efficiency: Modern paint booths have energy-saving features. This reduces costs and provides an environmentally friendly solution. Work Safety: Employee health is protected by expelling harmful gases and particles that may occur during paint applications. Compliance: Paint booths make it easy to meet industry quality standards.

Condition: new, Year of construction: 2024, Functionality: fully functional, machine/vehicle number: 20250109, total height: 1,470 mm, overall weight: 500 kg, total length: 1,740 mm, total width: 900 mm, type of input current: three-phase, workpiece weight (max.): 60 kg, tank capacity: 120 l, input voltage: 400 V, usable tank capacity: 50 l, rotational speed (min.): 50 rpm, rotational speed (max.): 180 rpm, power: 4 kW (5.44 HP), drum inner diameter: 640 mm, input frequency: 50 Hz, input current: 16 A, warranty duration: 12 months, Equipment: rotational speed infinitely variable, With a round work container, vertical slatted wall segments and a rotating plate-shaped base (see Fig. "Container details") with adjustable speed. The compact machine is removable and mounted on a base frame. To achieve a long service life, the work container and base are each lined with a PU coating that is at least 26 mm thick. The 120 L. container can be filled with 50 L. (approx. 60 kg.) of product/compound per batch, depending on the shape of the workpieces. The Turbo-Line 120 is suitable for deburring and polishing a wide variety of metal, composite or plastic parts. Process description The deburring/polishing process is controlled via a manual touchscreen*, where times and speeds can be individually set. Water/compound are fed and adjusted via a manually adjustable ball valve that is included in the delivery. Grinding and workpiece abrasions are fed together with the liquid through a slot into the collection container below. The unloading of the finished products (tilting and emptying the working container) is carried out manually. The speed of the three-phase motor, which can be changed as required, is controlled by a frequency converter. * The functions of the device are controlled via the 5-inch color touchscreen. The most important parameters controlled here are speed and process time. Cslrar Eovvvchjdjgt

Condition: used, Year of construction: 1979, Functionality: fully functional, Automatic galvanic system - zinc nickel drum for sale - Year of construction 1979 - Manufacturer: Sessler Galvanotechnik - Length 25 meters - Width 2.5 meters - Height: 4 meters - Clear internal dimensions of the tanks: (L*W*H) = 1300mm-600 mm-900 mm) - Siemens S7 - Ditec control system - Laser positioning of the trolleys - 2 trolleys - tank edge runners - 5 stations zinc nickel including release component - Automatic dosing stations for zinc nickel - Oil-cooled rectifiers from Munk - Filter system from Mefiag - 7 drum units Tscherwitschke - Wrench size drum 360 mm - Automatic filling system with lifting and tilting device - Automatic WMV drying system with 2 centrifuges The system is in good used condition and will be sold for a price of Offered for sale for €76,000 net. Cgoljvw Nqusrar Edet A preliminary viewing is possible by contacting us in advance (the system is still being built).

Condition: new, Year of construction: 2025, 1,000 x 1,900 x 2,000 mm powder stove, manufacturer Kigo O.E.! 1 Internal dimension length 2.000 mm 2 Internal width 1.900 mm 3 Internal height 2,000 mm 4 Outer dimension incl. thermoblock length 2,300 mm 5 Outer dimension incl. thermoblock width 2,300 mm 6 Outer dimension incl. thermoblock height 2,700 mm 7 Substructure 1 set of steel profile 50 x 50 mm 8 Walls 1 set of 1 mm galvanized sheet metal on both sides, outside RAL 5005 9 Insulation walls, ceiling 1 set rock wool 150mm 75Kg/m² 10 Oven floor 2 run-in rails for oven trolleys 11 Temperature 220°C 12 Fans 1 unit 6,000 m³/hour 13 Electric motors 1 pc. 1.1 kW, 1450 rpm, 3 F, 50 Hz 14 Thermal output 36 kW = 30,960 kcal/hour 15 Hinged doors on one side 2 insulated with rock wool 150mm 70Kg/m² Indirect heating via thermoblock Thermoblock 1 set stainless steel INOX AISI 316 Heating electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 16 burners 1 oven is electrically heated 1 exhaust air 1 piece device for exhaust air pipe, manual flap guide Celobqk Nborar Edjgt 2. powder coating booth (open spray booth) The overspray during powder coating is collected by the suction unit. The powder spraying booth is supplied on castors and is therefore mobile. - The suction unit is equipped with a 60 l powder container (rollbar). - There are 4 filters in the extraction unit as the 1st stage. - The absolute filter is located above the cabin. 1 Powder booth dimensions Width 2,454 mm Depth 2,400 mm Height 2,500 mm 2 Fan 1 pc. 6,000 m³/hElectric motor 3.0 kW 3 Filter Φ 325x600 4 pcs. type filter cartridges 4 Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5 Absolute filter 1 pc. type pocket filter 3. powder coating system Wagner, - Prima Sprint - 1 Dimensions of the Prima Sprint Depth 725 mm Width 480 mm Height 1.100 mm Weight Approx. 39 kg. Mains standard 230 VAC Frequency 50 - 60 Hz Inlet compressed air 6-8 bar Outlet compressed air 0.05 - 5.5 Nm³/hour - Corona hand gun PEM-C4 Ergo - EPG-Sprint control unit - Conveying unit with fluid crown ST 550/10 - Powder injector PI-F1 - Device trolley with agitator table

Year of construction: 2018, operating hours: 1,000 h, Condition: as good as new (ex-display), Material to be cleaned: sheet steel strips. Dimensions of the material bandwidth max. 1,250 mm The machine can process sheets from 0.5mm to 5mm. Cjlsh Rvz Ssrar Edogt Cleaning speed: max. 10 m/min Degree of oiling: slightly oiled (6bar dry and deoiled, approx. 11 m³/min Current 400V/50Hz; ~20kW Floor concrete for 10 N/mm² Flatness on target circle 5.0m +/-5mm Noise development ≤ 80 dB(A) Operating time max. 3 shift operation Environmentally friendly process without the use of chemicals

Condition: new, Year of construction: 2020, Model KPZ-2 Type Closed Working dimensions 900 w. x 1300 h. x 900 d. External dimensions 980 w. x 2100 h. x 1600 d. Operation Electric Power 0,69 kW x 2 Voltage 380 V Frequency 50-60 Hz Filter Polyester Number of filters 3 Filter surface 22,5 m² Fan aluminium Fan 74 dBa Air consumption 10,200m ³/h Warranty 12 months Other models KPZ-4 / 6 / 8 / ... on request Cgelrarob Al Sbo Edot

Year of construction: 2016, Condition: as good as new (ex-display), Manual PVC powder coating line for 3D fence panels ( NEVER USED ) Type of coating – electrostatic Cjloiryd Ujrar Edjgt PVC coating line is semi-automatic. Need 2-3 workers. Capacity of furnace – 10 pieces of 3D fence panels...baking time approx. 15 minutes ( with color of manufacturer IGP ). Of course baking time depends of color quality and chemical composition of color. The line is made on a modular system, which means that it can be installed in several ways, according to the possibilities of free space in the factory. Dimensions of line components - 1. Polymerization furnace – 2.500 x 3.500 ; Height – 3.200 mm 2. Painting booth ( 2 pieces ) - 3.000 x 2.000 ; Height – 3.200 mm 3. Washing chamber - 2.200 x 3.500 ; Height – 3.200 mm 4. Bath - 2.500 x 2.500 - Height – 900 mm plus two new Gamma pistols.

Condition: new, Year of construction: 2024, Functionality: fully functional, machine/vehicle number: 20250108, total height: 2,200 mm, overall weight: 700 kg, total length: 1,700 mm, total width: 1,300 mm, type of input current: three-phase, workpiece weight (max.): 75 kg, tank capacity: 120 l, input voltage: 400 V, usable tank capacity: 60 l, rotational speed (min.): 50 rpm, rotational speed (max.): 180 rpm, power: 4 kW (5.44 HP), input current: 16 A, warranty duration: 12 months, Equipment: rotational speed infinitely variable, The Turbo-Line 120 “S” model has a stainless steel ejection box mounted directly on the deburring machine. When the bowl lowers, the chips fall through a grid while the parts to be deburred remain on top. This Turbo-Line machine includes a 120-litre drum with vertical, straight sides and a separate base that rotates at an adjustable speed, normally between 115 and 135 rpm, but adjustable from 50 to 180 rpm. During operation, the grinding bodies inside the bowl create a uniform, spiral movement reminiscent of a twisted sausage. All areas of the machine that come into contact with the product, including the drum and the base, are coated with at least 26 mm of yellow polyurethane (PU) to ensure a long service life. The 120 liter work bowl can process up to 50-60 liters of product per batch, depending on the shape and size of the parts. The deburring parameters such as time and speed are individually controlled via a manual touch screen. The addition of water and compound is done via a manually adjustable ball valve, which is included in the delivery. Cgjlrarevvu Sns Edjt The finished products are discharged by tilting the bowl, a process controlled via the touch screen. The emptying speed is also adjustable via the frequency converter on the touch screen.

Condition: repair required (used), Year of construction: 2008, operating hours: 4,000 h, Functionality: limited functionality, Shotblasting machine for plates and europrofiles. 2.6 m width, 0,5 m height, 12 m infeed and 12 m outfeed motorised rollers. Machine is in working condition but needs a specialist that can do some refurbishments. Cgelrarjvgbcue Edot Some refurbishments made already: - new suction ventilator motor, new turbine blades, interior protection plates like new, new elevator belt, new coupling between 1 turbine and motor. Needs refurbishments: - electrical cabinet (machine runs with a new controlling system, old control panel is not setup and not functional) - brush repair (present but defective - we are not using it) - electrical connections and sensors (some of them present but not used)

Condition: good (used), Year of construction: 2011, machine/vehicle number: MS 1153, Offer 23158 Technical data ca : - passage to blasting chamber B 370 x 170 mm - blasting nozzle - Door opening to blasting chamber - Blasting material pressure vessel - blasting material recovery - separate control panel - space requirement blast machine 1600 x 2000 x H 1750 mm Cgslrar Ejllvr Dedjt - space requirement blasting material container 1200 x 1200 x H 2250 mm - Cartridge filter with suction fan MUNK - SCHMITZ - Air volume 700 - 1500 m³/h - Suction fan 3 kW - space requirement filter unit 1600 x 1600 x H 3250 mm - mot. driven inlet roller table 4 m - roller table without drive 3 m - roller width approx. 800 mm - roller table height approx. 700 mm

Condition: new, Year of construction: 2024, through-put width 870 mm working heigth 850 mm air consumption 400 - 800 l/min working pressure 3,4 - 8,0 bar suction capacity 17,4 m³/h total power requirement 1,2 kW weight of the machine ca. 160 kg dimensions of the machine ca. 1320 x 1200 x 1760 mm - Suitable for various blasting materials, e.g. quartz, glass ball, Plastic ball, etc. - Ideal for cleaning, derusting or removing paint from all metal parts Type, e.g. engine parts, fittings, signs, housings, rims, hinges - High-quality latex work gloves are firmly attached to the housing - Optimal visibility and occupational safety when machining workpieces because of the Window with glued protective film - Dust-free work due to all-round seals on the cover and door frames - Stable storage grid enables workpieces to be placed in the cabin interior - With drain opening for changing the blasting material - Suction pipe for the blasting material attached to the bottom of the collecting container Cgslrarsuhh Ars Edjt - With compressed air connection on the outside - Glass bead abrasives, corundum abrasives, silicon carbide, plastic Blasting media, etc. can be used Equipment details: - Very large, upward-opening front flap with gas pressure springs for quick access and easy loading and unloading - Integrated suction system with exchangeable air filter - Jet gun without finger trigger - Air flow is controlled via Foot pedal - Four fluorescent tubes (230 volts), in a separate housing with protective screen and exchangeable protective film, including five replacement films - 2 separate switches for suction and cabin lighting - Regulation of the working pressure via pressure regulator with manometer - Cross struts on the feet allow easy transport with the pallet truck

Year of construction: 2019, operating hours: 1 h, Condition: as good as new (ex-display), Air circulation oil / gas chamber furnace model SOS 80 O Exhibition machine Technical data: Usable space dimensions: Width approx. 1200 mm Height approx.: 1800 mm Depth approx.: 3000 mm trolley on request material Housing inside: Sheet steel 0,8 mm FAL welded or riveted tightly Outside housing: sheet steel 0.8 mm Base plate sheet steel 1.5 mm Painting: RAL 1013, as standard, powder coated Insulation material: Mineral wool Insulation thickness: walls - 160 mm ceiling: up to 240 mm, 100 kg/m3 dense Celrar Ejc Nbitjdsgt Performance data: Heating mode: oil Heating capacity: approx. 80 KW 1 oil burner a' 80 kW Total connected load: approx. 5,4 KW Temperature range: up to 250°C, infinitely variable Changes and errors in the technical data, and prices as well as subject to prior sale.

Condition: used, letter stencils negative stencils -Letter stencils: negative stencils, extensive range Cslju Intgorar Edogt -Type: German medium mirror, large letters numbers symbols -Dimensions box: 465/330/H65 mm -Weight: 8.1 kg

Condition: new, Year of construction: 2024, Functionality: fully functional, machine/vehicle number: 20250106, warranty duration: 12 months, total width: 685 mm, total height: 1,665 mm, total length: 1,000 mm, type of input current: AC, overall weight: 350 kg, inner dimension width: 520 mm, inner dimension length: 750 mm, inner dimension height: 660 mm, input voltage: 230 V, Equipment: cabin, documentation/manual, lighting, Compact, front-operated, semi-automatic 2-in-1 blasting cabinet made in Denmark with removable drum for blasting small to medium-sized workpieces / 3D printed components. Colrarsvvmaqs Edegt - You save time, air and energy. - Flexible adaptation to the shape of the workpiece. - Eliminates tedious manual work. - Eliminates bottlenecks in production. - Easy and simple operation due to semi-automatic operation. The integrated rotating drum can continuously and automatically remove plastic or metal particles from small parts after printing. The nozzle can be started automatically when the drum is rotating. After cleaning the parts, clean compressed air can be blown in to remove the residual dust from the parts. The drum itself can be easily and quickly removed for filling or emptying. For manual blasting, the drum is removed and the entire blasting chamber can be freely operated using a foot pedal. - Professional compact blasting cabin - 1 large swing door with safety door switch - Safety glass, replaceable glass pane - Rubber coating on the inner side walls - Integrated cabin interior lighting - Stable nozzle holder - Nozzle(s) made of tungsten carbide - Foot switch for manual blasting - Pressure gauge and pressure regulator

Condition: good (used), Year of construction: 1993, Offer 24299 Technical data: Cslret Hurxsar Edsgt - Volume flow approx. 2170 m³/h. - Dust bag / chip bag up to 170 L - Connection spigot 160 mm - Connection spigot adapter 2 x 100 mm - Drive power 400 V / 2.2 kW - Space requirement W 1200 x H 1900 x D 550 mm - Weight approx. 85 kg

Year of construction: 1986, Condition: good (used), machine/vehicle number: 4670, Offer 24460 Technical data: - Nominal / continuous temperature preselectable up to approx. 1150 ° - Digital temperature setting Cjlrasu Abg Asr Edjgt - timer - Interior dimensions approx. W 200 x H 190 x D 350 mm - Loading through front door - Opening width of front door W 200 x H 190 mm - Drive 400 V / 7.5 kW - Base frame H 800 mm - Space requirement approx. W 900 x H 1450 x D 900 mm - Weight approx. 120 kg