Condition: new, Number of sanding units 2 St. sanding width 190 mm Sanding height max. 2-180 mm LÖWER double-sided grinding machine DSM 2000 ----- Double-sided single wood sander for sanding Solid wood such as window wood etc. Stable top quality Guide with long casting tables, brushing and finishing equipment and conveyor belt feed. Suitable for high continuous loads even with higher chip removals. - Staggered sanding and finishing units at the top and bottom - Directly driven rubberized grinding rollers for slip-free power transmission - Combined grinding via roller and shoe for high chip removal at the same time flat intervention zone - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and higher grinding Grinding belt service life - Forced pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the sanding rollers Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom using a precision threaded Crsdpfovu Hdtex Ah Usi spindle Dimension display via scale ring (resolution 0.1mm) - Sanding belt tension via pneumatic cylinders with constant clamping pressure - Sanding belt change with pneumatic belt relaxation in seconds - Adjustment of the sanding belt run when changing the belt - electro-pneumatic compressed air monitoring - Run-in protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and non-stick conveyor belts over heavy, 1000mm long cast tables with a finely planed surface and Spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and even workpiece transport - Feed gear motor with three different feed speeds for quick adaptation to different types of wood - all motors electrically protected - Ergonomically arranged controls on the workpiece inlet side - automatic workpiece thickness scanning (no previous measurement necessary) - Digital thickness display (resolution 0.1mm) with modern magnetic tape system Technical data: - Sanding belt speed: 22 m/s - Sanding belt length: 1800mm - Sanding belt width: 200mm - Working width: 190mm - Grinding thickness: 2-180mm - two brake motors for drive: 5.5 kW - Feed motor: 1.0 kW - Feed speed: 6, 11 and 16 m/min. - automatic height adjustment: 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle: 2 x 120mm and 2 x 150mm - Pneumatic connection 6 bar - Working height: 850mm - Length: 2105mm - Length with control panel 2490mm - Width: 880mm - Height: 1910mm - Weight: approx. 1500 kg - Operating voltage: 400 volts, 50 Hz, 3P - CE version ----- ----- Basic price of the machine on request! ----- ----- Special accessories with surcharge: continuous feed 4-20 m/min. for speed adjustment to the previous machine Price on request Workpiece blow-off - using nozzles from above and below at the machine ...

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, WEINIG Unicontrol UC 10-5 Window Production Machine 1. Electronically controlled crosscut saw with laser switching between saw cutting and zero-point wheel, 3 kW motor 2. Grooving spindle 50 x 630 mm for tools 6 x 80 mm, 15 kW motor 3. Longitudinal/synchronous profiling spindle 50 x 320 mm for tools 4 x 80 mm, 11 kW motor 4. Grooving spindle (between 1st and 2nd lifting spindle), D = 40 x 40 mm, axially indexed, 3 kW motor 5. Longitudinal profiling spindle 50 x 320 mm for tools 4 x 80 mm, 11 kW motor 6. Longitudinal profiling spindle 50 x 320 mm for tools 4 x 80 mm, 11 kW motor 7. Clamping spindle 40 x 150 mm, 3-position axial cycle, 2-position radial cycle, 3 kW motor Saw and grooving spindle on the right side, 3 kW motor Hardware spindle 40 x 150 mm, 3 kW motor Adjustable feed speed 6-12 m/min, 1.1 kW motor 4-position counter changer Electronic length stop, 3600 mm Workpiece return system with automatic rotating mechanism Automation package Interval-controlled sash support Double parts package Laminated fabric tables (for sanded surfaces) Crsdpfx Ahoxmr N Is Uei Pressure guide on the left, max. wood width difference 100 mm Machine in very good technical and visual condition

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 92552, working width: 230 mm, planing height: 120 mm, working height: 120 mm, spindle diameter: 40 mm, power of feed motor: 1,500 W, 🪚 2001 Weinig Quattromat 23P Planer Moulder – Industrial Performance in Very Good Condition Now available for sale: a 2001 Weinig Quattromat 23P, one of the industry’s most reliable and compact 4-sided planing and moulding machines, ideal for workshops producing mouldings, profiles, cladding, architraves, and more. This unit is in very good condition, fully operational, and perfect for businesses looking to increase productivity with a trusted European-built planer moulder. ✅ Key Features – Weinig Quattromat 23P Year of Manufacture: 2001 Condition: Very Good – well-maintained, and ready to run Working Width: 13 to 230 mm Working Height: 6 to 120 mm Number of Spindles: 4 Spindle Diameter: 40 mm Spindle Speed: 6,000 rpm Feed Speed: Variable up to 20 m/min Power: Approx. 21 kW combined spindle power Infeed Table: 1,800 mm Pneumatic Pressure System: For consistent timber hold-down Digital Readouts: For quick and accurate spindle positioning Straightening spindle motor: 4 - 7.5 KW (5.5 - 10 HP) Vertical spindles motor: 5.5 - 11 KW (7.5 - 15 HP) Top spindle motor: 4 - 11 KW (5.5 - 15 HP) Feed motor: 1.5 KW (2 HP) Spindle speed: 6,000 rpm Spindle diameter: 40 mm Tool cutting circles of moulding spindles: 125 - 200 mm Adjustment range of spindles (axial): 30 mm Adjustment range of straightening spindle: 5 mm Feed speed: 8 m/min. Feed roller diameter: 140 mm Feed roller width: 2 x 50 mm Width of roller in the outfeed table: 50 mm Adjustment range of straightening table and edge-jointing fence: 10 mm Height of right fences: 60 mm Length of straightening table: 2 m Reference engraver with cutter: Yes Pneumatic pressure for feed rollers: Yes Pneumatic adjustment of infeed roller in front of 1st bottom spindle: Yes Pressure roller from above and left in front of machine infeed: Yes 🛠️ Machine Capabilities 4-sided planing for smooth and dimensionally accurate timber Profile moulding (e.g. tongue & groove, chamfering, rebating, etc.) Batch production of window, door, or cladding components Compact footprint – ideal for smaller workshops or mobile production lines Easy spindle access and minimal setup time 📦 Included with Machine Weinig Quattromat 23P base unit Dust extraction ports Original manuals and operator instructions Fully tested, serviced, and ready for production 🪵 Perfect For: Joinery workshops Timber frame manufacturers Furniture makers Shed and fencing producers Custom millwork and architectural moulding shops 📍 Availability & Delivery The machine is in stock now and available for immediate inspection and dispatch. We offer delivery across Ireland, UK and Europe. Crsdjwnr Enspfx Ah Uji 📞 Contact Us Today Boost your timber processing capabilities with this robust and accurate Weinig Quattromat 23P. Weinig Quattromat 23P for sale Used Weinig planer moulder in very good condition 4-side planer moulder woodworking machine Industrial wood planer for moulding production Compact planer moulder for small workshops Weinig planing and profiling machine UK / Ireland / Europe Second-hand Weinig machinery for woodworking

Condition: used, Length 2700 mm Width 1100 mm Height 850 +- 150 mm engine output 0,37 kW Electric capacity 0,5 kw compressed air 6 bar Horizontal impregnation system 'Pro flow' for individual parts with rinsing circuit. ----- Features: Machine for horizontal flooding of individual parts. The product will go through flooded a row of nozzles. The excess product is then removed through air jets blown off. The pump and the air nozzles are controlled automatically and only then operated when the workpiece passes through. In this way the Compressed air consumption reduced. The circulation operation ensures minimal product consumption. ----- Construction features: structure Sturdy steel frame, painted with high-strength, water-soluble products. Machine body made of heat-sealed, thick polypropylene plates. 4 independent chambers for inlet, flooding, blow-off and outlet. Horizontal feed of the workpieces By motor-driven rollers made of plastic with grooves. Electrical converter for controlling and changing the conveying speed. transmission The machine is equipped with an exclusive system so that all Gear located outside the flood chamber and easily accessible to the Operators are to guarantee a longer service life and the to facilitate maintenance operations. The moving components are protected by cover plates and appropriate Crsdpfx Asnl Nqqoh Uei seals protected. circulation pump Pneumatic double diaphragm pump made with valves, seals and diaphragms Nitrile rubber and housing made of plastic material (PVDF). air jets A blow-off system is present in the first chamber to prevent product leakage avoid. A second blow-off system after the flood chamber blows off the excess product from the workpiece. Electrical panel According to CE, degree of protection IP 55. Including inverter to the set feed rate. technical features Length mm 2700 Width mm 1100 Conveyor speed (min./max.) m/min 3-6 Motor power train group kW 0.37 Installed electrical power kW 0.5 Distance between infeed and outfeed rollers mm 2520 Working height (adjustable) mm 850 +- 150 Min. length of the workpieces to be flooded mm 250 Max. width of the workpieces to be flooded mm 300 Max. height of the workpieces to be flooded mm 250 Compressed air consumption lt/min 2000 Pressure of the required compressed air bar 6 Equipment and available accessories Flushing circuit for Pro Flow ----- Price of the above machine: on request! plus packaging and transport ----- (Technical information according to the manufacturer - without guarantee! Illustrations may be dated Deviate from the original, prices net, plus VAT (domestic))

Condition: new, Bore diameter variabel mm Number of heads horizontal 3 St. Number of heads vertical 4 St. weight 1500 kg Dimensions (L/W/H) 4800x1600x2400 mm Width mit Auflage 2300 mm Götzinger Power Drill Type BF 297 With the Götzinger PowerDrill you can, depending on the type and design: Griffoliven drill on the loose frame part or for finished wings, with multi-spindle drilling head, quick-change, also for milling of the lock case for WK 2 or intermediate gear Ecklager drill on loose frame part, with Mehrspindelbohrkopf, quick-change, corner-oriented over stop or custom made (tilt window) Drill vertically from above for fitting, pre-drill for clip on loose frame part Milling vertically from above for pushers, profile cylinders, 3-D hinges Horizontal drilling with 2 drilling units, different drilling diameters, Dowel drill front and long side, plywood / fighter, sprouts, Corner connection, front door etc. Milling horizontally for lock case / fitting etc. Csdpfx Ajd Ih Hqjh Ueri machine description Base frame in stable welded construction, linear guide for the X-axis Table top 3,000 x 200 mm 6 clamping cylinder pneumatic with auto. Ausweichhub 2 side stops for machining on the front side, manually swiveling in and out 2 longitudinal stops can be manually swiveled in and out Travel: X-axis - 3,000 mm working length Y-axis - 120 mm Z-axis - 105 mm Aggregate: 1 drilling unit (unit 1) vertically from above, drill motor 1,1 KW Speed ??1,500 - 12,000 rpm, 1 spindle, collet holder ER 20 1 Bohraggreagt (unit 2) vertically from above, drill motor 1,1 KW Speed ??3,000 rpm, with drill head quick change device 1 boring head BKF 3, olives, quick-change 1 boring head BKF 3/2 corner bearing, quick-change 1 milling unit (Agg.3) vertically from above, milling motor 2 KW, 1,500 - 16,000 rpm, collet holder ER 25 2 horizontal drilling units (Agg.4 and 5) 1.0 KW, 1.500 - 12.000 U / min, Collet holder ER 20 1 milling unit horizontal (Agg.3) 2.0 KW, 1.500 - 16.000U / min, Collet holder ER 20 Electro-pneumatic control with 3-axis control X, Y, Z NC positioning controller make B + R input via TFT display 10 " Machine complete with 1 set of drilling tools dm 6, 8, 10 and 12, 2 roughing carbide cutters HM dm 16, CE compliant, ready for connection Suction connection: 1 x dm 120 Power connection: 1 x 400 V, 16 amps Air connection: 1 x LW 9 mm OPTION: Longitudinal stops right / left with NC axis high / low programmatically, thus dimension input by folding / light measure possible, Dimension: LxWxH = 4.80 x 1.60 x 2.40 m - weight machine 1,500 kg (technical data according to manufacturer - without guarantee!)

Condition: new, Assembly line consisting of: Item 1.0 / RU-CBM 4000 work table with running rail extended by 500mm for additional assembly an aluminum holder screwing machine for RU-CSA-SMB or RU-CSA-SMZD with RU-SH special screwdriver, support table Length 4000 mm, width 1400 mm, inclination of the working platform manually adjustable. Holder for fitting scissors or fitting punch. 16 pieces of swiveling counter-holders for hanging the wings, completely pneumatic Foldable for unhindered movement of the wings on the table surface. Device for scanning the sash fitting length for constant and variable/central gear seat for already drilled wings, colored Dimension recognition of the fittings. RU-SH, special screwdriver with pneumatic depth switch on carriage mounted, safety control, pneumatic height adjustment, Screw feeder with automatic shutdown of the filling container (Manual insertion for a second screw length on the special screwdriver upon request). RA-8, turret stop for 8 screw levels mounted on the carriage. RA-4, turret stop for 4 different wing widths Swivel table mounted. Pneumatic wing measurement sensing. operated, scanning range up to 2500mm simultaneous clamping of the scanning. PSF - Pneumatic tensioning device for sashes. Working height adjustable from 900 - 1000 mm. Support table covered with felt. Running rail extended to the left by 800 mm. Item 1.1 / 5035-1 Pneumatic swivel device of the work surface with foot valve Item 1.2 / 0500000 Holder matched to customer punch/scissors. For mounting a hardware punch provided by the customer or Fitting shears (third-party manufacturer) on the sash assembly table. Please specify make when ordering!!! Item 1.3 / 5597-7 Driving device for RU-CBM on semicircular rails. The castors are on the left and right of the base frame of the table mounted. Item 1.4 / 6354-6 3 double meters of semicircular rails 30 x 10 mm. Item 1.5 / 0730000 RU-SBL3000/40 free-standing fitting bearing, Length 3100 mm, depth 1250 mm, height 2200 mm, Stand frame on the front without supports, 40 compartments, divided into 10 compartments in a row by dividers Crsdod Ih Hujpfx Ah Uoi and a continuous shelf at the top, Compartment size: width 280 mm, height 150 mm. Item 2 RU-CSA-SMB aluminum holder screwing machine with automatic Screw feeding and manual feeding of the aluminum holders from one traveling box with pneumatic positioning device, Screwdriver with depth cut-off with 4-fold turret stop. Pneumatic adjustment device in the y direction against 2 pieces 6-fold Revolver attacks. Feed container for manual feeding of rotary holders or clip holder in square shape 18.5 x 18.5. The holder is manually pushed into a channel in the box and with positioned in front of the screwdriver mouthpiece using a pneumatically operated slide. Profile depth max. 150 mm, screw spacing in the y direction max. 120 mm. Item 3 RU-S48-A6-350 column slewing crane for chain hoist, with 6 m aluminum boom Version with column, smooth-running boom and sliding chassis for swivel and trolley travel manually by pulling and pushing the load. Projection 6 m Construction height 4,461 m Lower edge of boom 3.722 m (top edge of boom 3.9 m) Swivel range max. 270° Painting of the steel construction in RAL 7035 The base plate is attached to the on-site hall floor At least 250 mm thick. Designed, of course, according to the valid STANDARD EN 13155 Warra...

Condition: new, Bore diameter variabel mm Number of heads horizontal 3 St. Number of heads vertical 4 St. Götzinger Power Drill in special version with dübelleim and press-in station With the Götzinger PowerDrill, you can choose: - Drill the front and long sides - Doweling of doors, seatings, fighters - The drilling patterns are freely programmable - You can: Grip handle and corner bearing, with quick-change Multi-spindle drilling heads - You can: lock casings, pusher and PZ as well as 3D tapes and drill - The machine has a horizontal and a vertical milling unit - A simple control lets you create drilling and milling programs, Save and recall POWER DRILL - drilling and milling machine Universal drilling machine for drilling olives, corner bearings, dowel work On the front and the front, milling, lock boxes, tapes, etc. Base in stable design, covered with sheet metal Table top 1800 x 200 mm Processing unit: X-axis - 500 mm working travel Y-axis - 100 mm Z axis - 105 mm 1 drilling unit horizontal (dowel drilling unit left) Drilling motor 380 V, 1,100 W Clamping chuck d = 8/10 4,000 - 11,000 rpm can be adjusted 1 drilling unit vertically from above - fixed Drilling motor 1.1 KW, 3,000 rpm Quick change of the drill head 1 drill head BKF 2/3, quick-changeable, (corner bearing) On the loose part, hardware according to customer requirements including drill replacement Control: electro-pneumatic with three axes NC positioning controller and integrated machine function Input via TFT display, 10 "color Machine complete, CE compliant, with 1 set of drilling tools Dübo je 1xd = 6,8,10,14 + 2 Roughing cutter d = 16, 1 milling cutter d = 20, ready for connection 1 drill head BKF 3, fast exchangeable for olives including drill bit Fitting according to customer requirements 2 drilling units 1 x horizontal for drilling from above (for tapes) 1 x vertical for dowel work, right Drilling motor 1.100 Watt, infinitely variable 4,000 - 11,000 rpm with collet chuck ER 20 2 Milling units for lock boxes 1 x horizontal for tapes, lock boxes 1 x vertically from above for PZ, pushers, tapes Milling motor 2.2 KW Speed ??adjustable 3,000 - 16,000 rpm Clamping tool holder ER 25 1 length stop right and left, working length 2.8 m NC-controlled When the length stop is used, the fixed stops are removed. Dimension: LxBxH = 2.50 x 1.50 x 2.20 m - Weight machine 850 kg PowerDrill LxBxH = 0,30 x 0,30 x 6,00 m - Weight length stop 100 kg 1 Dübelleim- and press-in station consisting of: - Swing conveyor for dowels with feed -Dübeleinpressstation Csdpfx Aod Ih Hysh Ueri -High pressure glue pump made of stainless steel with glue container - Full jet valve for precise glue application Exhaust nozzle Price for 1 dowel diameter The basic machine will be about 300 mm longer (Technical data according to manufacturer - without guarantee!)

Condition: new, Number of sanding units 8 st. sanding width 180 (260) mm Sanding height max. 160 mm Dimensions (L/W/H) 3065x1600x1900 mm weight of the machine ca. 1500 kg LÖWER Leistomat SD ----- Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm 1 softisc unit Ø=200mm above 0.75kW, 1 slat roller unit L=200mm top 0.75kW, 1 soft disc unit Ø=200mm bottom 0.75kW, 1 slat roller unit L=200mm bottom 0.75kW, 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm - Linear guidance of all grinding units Linear ball bearing sets on hardened shafts - time-controlled immersion of all lamella roller units directly above the incoming workpiece edges. By the It is possible to immerse the aggregates deeper into the profiles to be able to deliver. - Motorized workpiece thickness adjustment of the machine - variable grinding flap speed via frequency converter Cedpevnv Uhofx Ah Usri for adjusting the grinding intensity using frequency converters (separate for discs, surface rollers and side rollers) - Disc aggregates as soft discs with Velcro fastener for Grinding wheels (wood pulp) - Feed via three lower and one upper conveyor belts and Spring-loaded pressure rollers with infinitely variable speed 4-15m/min - Parameters that can be set using the touch panel are workpiece thickness, Workpiece width (left side units individually), immersion depth Side units, spindle speed, feed speed - Saving the parameters as machine programs in program mode - Working in automatic mode with non-contact Workpiece width detection and profile detection as well as automatic Adjustment of the sanding units to the workpiece width and the Profile shape (workpiece height is set in advance) - pneumatically clocked driven feed roller, automatic Clamping of the workpiece and feeding in after unit adjustment - Red/green indicator lights to indicate operational readiness - shortest workpiece length 380mm - Transport belt width 200mm - max. workpiece width 180mm (260mm in the envelope process) - Workpiece height 12-160mm - Suction connection 4 x 100mm and 2x80mm diameter - Sensor-controlled tool blow-off directly on the discs - Length (case) x width x height (mm): 3065x 1600 x 1900 Complete length: 4365mm (including roller conveyor with integrated workpiece width detection) - Weight: 1500kg - Operating voltage 400V, 50Hz, 3P, air connection 6 bar - CE version ----- Price of the above machine on request! ----- Special accessories with additional costs: Set of replacement slats for Leistomat SD-200 consisting of Area aggregates: 30 strips EH45 / 200 - 7 (rolls) 30 strips EH45 / 200 - 20 (rolls) Folding units: 96 strips M55 / 120 - 4 SmartFlex slat disc Ø200 solid with 30 grooves 50mm long Set of replacement slats for SmartFlex slat disc consisting of 60 strip M35 / 50 K 180-7 p Sandpaper disc VB for soft disc D=200mm grit 220 with velor backing (Velcro), pack of 100. Sandpaper disc VB for soft disc D=200mm grit 280 with velor backing (Velcro), pack of 100. ----- Price of the above-mentioned special accessories on request! -----...

Condition: used, Working width 3450 mm Working height 2000 mm Number of cylinders 5 St. loading dimensions L x W x H 3600 x 1200 x 2720 mm Hess "Multipress" Perforated Plate Press For all sloped, segmental, and round-arch windows and doors. Also for interior work or frame construction. For gluing staircase block joints and much more. Largest working area approx. 3450 x 2000 mm External dimensions approx. 3600 x 1200 x 2720 mm The vertical perforated plate press is constructed of heavy-duty, torsion-free steel. Thanks to its simple, robust, and economical design, it has a long service life. The perforated plate is made of 10 mm sheet steel with a 50 mm hole pattern. Crjdpfx Ahswqr R Aj Uei The pressure cylinders and abutments are self-locking. 5 plug-in hand hydraulic cylinders on a perforated plate with a built-in pump, 2000 kp pressure relief valve, 140 mm pressure plate width, 80 mm pressure plate depth, 60 mm cylinder stroke 4 fixed individual abutments (Technical specifications according to the manufacturer - no guarantee!)

Condition: new, Number of spindles 6 St. Working width 250 mm Working height 150 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-24 m/min. weight 4770 kg Dimensions (L/W/H) 4722x1860x1776 mm Vierseitenhobelmaschine Kuper SWT XL-6 in Fenster-Version mit elektronischer Axial- und Radialverstellung der Spindeln. Schwerer Maschinenständer, verwindungsfrei und schwingungsarm. Anzahl der Spindeln: 6 Arbeitsbreite: 250 mm Arbeitshöhe: 150 mm Abrichttischlänge: 2500 mm Spindeldrehzahl: frequenzgeregelt 4.000 - 8.000 U/min Vorschubgeschwindigkeit: 6-24 m/min Crjdpfx Ahsvnv Ubs Usi Ausführliche Beschreibung finden Sie in nebenstehender PDF-Datei! (Technische Angaben laut Hersteller - ohne Gewähr!)

Condition: new, Year of construction: 2025, Number of motors 2 Stück 0 3000 mm Control ja/CNC loading dimensions L x W x H 4000 x 1500 x 1500 mm Weight 800 kg HECHT double miter saw Exenso DS350E - 3000 mm ----- For wooden glass strips, rungs, profile strips, aluminum strips, etc. Pos. 1.1 Article number 942.5103 1 piece HECHT Exenso DS350E - Working length 3000 mm - Swivel range 22.5° (inside) to 135° (outside) - Right head movable - Saw blade holder Ø 350 mm - Incl. 1 piece center support. - Units clamped pneumatically. - Positioning control Exenso DS3 with touch panel 15" display in dust-proof monitor housing. - 3-axis control, 1 longitudinal axis and 2 swivel axes. - Entering the cutting data by hand - Processing data from a cutting list (data set according to specification) - Processing measuring rod data (GMF wireless caliper) - Ethernet connection 10/100 (TCP/IP) - USB interface - Incl. control cabinet, motor and software licenses. Item 1.2 Item number 723.0121 2nd DS saw blade wood Bevel/bevel/flat tooth - positive Item 1.3 Item number 942.5236 2 sets of DS workpiece clamping combined Combined workpiece clamping consisting of: Pneumatic swivel clamp - for clamping the material from above. (Free access to the work table) Pneumatic horizontal clamp - anti-twist clamping cylinder with pressure piece. The clamps can be selected individually via the saw control. The clamping sequence can also be set via the control. Including safety pre-tensioning pressure Scope of delivery for 2 sets: - 2 pieces (left/right) vertical swivel clamps. - 2 pieces (left/right) horizontal clamps. Item 1.4 Article number 942.5997 DS pneumatic feed device Item 1.5 Article number 945.2007 Packaging DS350 (transport frame) ----- Total price in this version - on request! ----- ALTERNATIVE options, prices on request! ----- For horizontal clamping of the remaining pieces with blunt glass strips instead of the 2nd set Item 1.3 943.5236 DS workpiece clamping combined! Pos. 2.1 Article number 942.5201 ES / DS workpiece clamping from the front - 2 clamping cylinders with anti-twist protection - 2 cylinder holders with clamping lever ----- For rebated glass strips, instead of standard panels without a groove: Crodpfevzt D Tex Ah Uji Pos. 2.2 Article number 942.5241 DS350 table supports grooved according to customer sample The assembled table supports are milled according to the customer's drawing. Please send us all profile drawings that are to be sawn (pdf, dxf and hand samples) ----- If, for example, aluminum is also to be sawn: Item 2.3 Article number 942.5203 DS hydropneumatic feed device (instead of pneumatic feed cylinder) ----- OPTIONAL accessories, with additional charge on request: ----- Item 2.4 Article number 942.5237 DS "Excess length" software (subsequent steps must be confirmed) Sequence control including hardware. After entering a cutting dimension > max. cutting length of the system, the cutting is carried out in a cyclical manner. (Left unit cuts, right unit moves the material and cuts to size.) ----- Item 2.5 Article number 944.1023 GMF caliper 3000mm complete set (1500mm plus extension 1500mm) incl. charger and receiver. A robust aluminum measuring rail with a measuring ran...

Condition: used, Working width 3600 mm Working height 2600 mm Number of cylinders 5 St. loading dimensions L x W x H 4400 x 1150 x 2970 mm weight 3000 kg Schafberger + Sproedhuber Bavaria Frame Press ----- Machine is overhauled by us before delivery. With automatic pressing cycle + manual control for tenon + slot corner joints. CE-certified version Basic machine in the strongest welded frame construction, with thick-walled special hollow profiles. Credpfx Aew T Un Uoh Usi Guideways for the pressure beams for the press corners in a low-wear machined design. Fast, smooth, manual width adjustment via ball-bearing carriages, fixed in a hole pattern. Height adjustment and pressing via long-stroke cylinders in a single work cycle. Right-side press corners with integrated horizontal cylinders, therefore no vertical positioning of the horizontal pressure cylinders necessary, thus avoiding cylinder collisions. Lower abutment adjustable in several positions for the most favorable insertion height. 3 vertical press cylinders, double-acting, stroke adjusted to working height 2 horizontal press cylinders, double-acting Abutment and pressure plate depth 80 mm Working size: Length x Height = approx. 3,600 mm x 2,600 mm Space requirement/loading dimensions: approx. 4,400 mm x 1,150 mm x 2,970 mm (Length x Width x Height) Option: ALWA pressing supports for sloped windows (Technical specifications according to the manufacturer – no guarantee! Images may differ from the original. Prices are net, plus VAT (domestic))

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Cedpfst Tqy Esx Ah Ueri Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Number of spindles 4 St. Number of tools 11 St. Spindle diameter 50,40 mm Spindle length 285,125 mm length 4000 mm width 2000 mm height 2200 mm Weinig Univar 10/3 folding machine ----- For milling around windows, doors and the like with uneven circumferential profiles. Machine suitable for wood thickness 68 to 92 mm Time required per frame milling, medium size 1.20 x 1.20 m - approx. 2 minutes. The available tool positions are selected using a selector switch on the control panel retrieved. Machine with 3 hydraulically controlled right precision Lifting spindles for holding 3 tool sets, 2 x 95 mm spindle stroke per spindle The spindle stroke takes place in a U-movement, so that the opening is possible for short parts The milling stop remains as small as possible. Spindle stroke horizontally fine Adjustable for both tool positions from the operator side. Central lubrication for the spindle units. The 1. Spindle can be selected in right-left rotation. This spindle dips the last 100 mm of each frame end appropriate synchronization tool into the passing wood. Through this This prevents the tool of the subsequent milling spindle from running in the opposite direction working, causing tearouts. Excavation of the first 7 transport rollers using Footswitch. This shortens the lead time. An additional The support rail also allows large-format frames to be milled around. Continuous, chainless rubber roller feed with extreme short roller spacing. Height adjustment of the feed bar electrically readable. Electrical version according to VDE. Machine including operating tools, but without processing tools tools. Technical data: Working width min. 40 mm Working height min. 30 mm, max. 100 mm 1. Profiling spindle (synchronous and counter-rotation) ----- -- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm with synchronous automatic immersion 2. Profiling spindle ----- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 3. Profiling spindle ----- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Credpfxjvnv Uue Ah Usi Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 4. Profile spindle - fitting unit on the right ----- For milling the fitting groove in the milling cycle or for grooving in the longitudinal profile. Pneumatic horizontal movement with Selector switch in the control panel. Motor 2.2 KW Speed 6,000 rpm Spindle diameter 40 mm Clamping height 125 mm, 2 tools Tool flight circle min. 140 mm, max. 180 mm Motor power feed 1.1 kW Feed speed 6 - 12 m/min. ...

Condition: used, Working width 3550 mm Working height 2250 mm Number of cylinders 5 St. loading dimensions L x W x H 4500 x 900 x 2600 mm Hess Speedy frame press ----- Machine is functionally tested Insertion dimension / press length max. 3,550 mm Insertion dimension / press height max. 2,250 mm Sliding carriage for width adjustment, locking in 50 mm Double hole grid system Electrical height adjustment of the long-stroke cylinders (hydraulic) Insertion height of the abutment plates can be preselected in 4 positions 3 vertical pressure cylinders stroke 1000 mm Pressure force per cylinder 2000 kN / 20000 N 2 horizontal pressure cylinders stroke 80 mm Pressure force per cylinder 1250 kN / 12500 N Pressure plate depth 100 mm width 140 mm Cylinder fixation / abutment grid 50 mm Csdpfxovn U Ruo Ah Uori Medium pressure beam with shut-off valve Final pressure shut-off and post-pressure control Control and press sequence in touch button operation Adjustable pressing pressure min. 25 – max. 160 bar Electrical connection 2.2 kW / 400V Control for gluing sloped windows 2 pendulum pressure plates 45 degrees Machine dimensions W=4500 mm, D=900 mm, H=2600 mm Weight approx. 1800 kg Pictures original. Video not original, shows identical model (technical data according to manufacturer - no guarantee!)

Condition: used, Year of construction: 2018, Number of motors 1 Stück 0 2500 mm Crsdpjvpr N Refx Ah Usi Control nein Hecht ES 350 single-sided glazing bead saw ----- Pneumatic pivoting against fixed stops. 45º/ 90º/ 135º with pneumatic sawblade feed pneumatic tilting via manual tilt stop with machine base, pneumatic clamping HM sawblade 350 x 3.0/2.2/30 Z 100 Saw stand dimensions: length 700 mm, depth 1,600 mm, height 1,500 mm 1.5 m touch stop 1.5 m support with support 3 m touch stop Support extension from 1.5 m to 3 m with support Table inserts grooved for rebated glazing beads HECHT ASB manual length stop with digital display, 2,500 mm With dust extraction unit (Technical specifications according to the manufacturer - no guarantee!)

Condition: used, Tenoning spindle 1 St. Number of milling agregates 5 St. Spindle diameter 50 mm Control Weinig, PC-Nexus # 2774 Weinig Unicontrol 6 with NC spindles Machine will be cleaned and completely checked before delivery ----- Technical data summary (please enquire about any additional accessories included) Item 1: Cross-cut saw ----- > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3 kW > Radial adjustment path pneumatically controlled to 8 positions, e.g. for edge rounding from above > Laser aiming light for detecting the saw section Item 2: Rounding unit horizontal below ----- > Position: horizontal below > Motor power: 1.5 kW > Spindle diameter: 20 mm > Clamping length 25 mm > Spindle speed: 9,000 rpm > Max. tool flight circle: 130 mm > Axial adjustment path mechanically coupled with Crosscut saw > Adjustment path radial pneumatically controlled on/off Length stop NC controlled ----- > Length 3500 mm > Electronic length stop Item 3: Tenon and slot spindle ----- > Number of tools: variable, stepless adjustment, NC Crsdpfxsvu Hghs Ah Uei > Tool clamping length: 320 mm > Vertical spindle stroke: variable 254 mm, stepless adjustment, NC-controlled > Spindle speed: 3500 rpm > Tool flight circle max. 320 mm > Spindle diameter: 50 mm > Tool diameter max.: 320 mm > Motor power: 11 kW Item 4: 1. Profiling spindle (same and opposite rotation) ----- > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 7.5 kW Item 5: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, stepless adjustment, NC > Tool clamping length: 320 mm > Vertical spindle stroke: variable 254 mm, stepless adjustment, NC-controlled > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 11 kW 2 feed rollers axially pneumatic opposite the spindle controlled, 2 positions Rung guide consisting of: Guide ruler in the stop (area of ??the synchronous spindle), Rung support bar from above in the area of ??the profile milling unit vertically on the right and profiling spindle. Pos. 6: Profile milling unit horizontal top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed ??9,000 rpm > Tool flight circle max. 130 mm > Axial adjustment range 30 mm, 8 positions > Radial adjustment range 125 mm, 8 positions Pos. 7: 3rd profiling spindle (fitting spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment range 115 mm, 8 positions > Radial adjustment range 110 mm, 8-way turret > Spindle speed: 5850 rpm > Spindle diameter: 40 mm > Tool flight circle max.: 210 mm > Motor power: 3.0 kW Item 8: Profile milling unit/grooving unit from below ----- > Motor power: 3.0 kW > Tool clamping length: 125 mm > Axial adjustment range 100 mm, 8 positions > Radial adjustment range 1...

Condition: used, Number of boring motors 1 St. boring of corner bearing 1=yes, 0=no 1 ja_yes boring of olive 1=yes, 0=no 1 ja_yes 1 HESS fitting drilling station for corner bearings and olives This Hess drilling station for tradesmen offers a lot of drilling technology for little money. A complete station for drilling corner bearings and olives with all the important features, such as 2 clamping cylinders, drilling depth sensing, effective suction, stop systems for corner bearing and olive drilling, drilling head with interchangeable chuck, adjustable drilling feed speed, automatic program sequence. This means technology for perfect work: just one machine with just one drilling unit and just one drilling head for 2 work steps. The system: - Base frame as a support wall for frames and sashes up to 100 mm - Drilling unit positioned in the middle, height manually adjustable via threaded spindle - Drill hole position and depth set to the specified fitting type, can be adjusted via a stop system when changing types - Drilling feed speed can be variably regulated via throttle valve - Direct extraction - Electro-pneumatic control system with automatic Program sequence for - Fixing workpieces - Drill motor on - Drilling unit forwards - Drilling - Drilling unit backwards - Drill motor off - Releasing workpiece fixation - Fixed stop systems Basic equipment / Technical data: Sturdy base frame as a support wall, precise support made of abrasion-resistant and dimensionally stable plastic, for frames and sashes up to 100 mm thick, Corner bearing and olive drilling in one machine and in one drilling unit, simple and convenient, vertical work, easy handling, no templates, minimal time required for the safe workpiece positioning, guarantee for exact and precise drilling, 2 clamping cylinders for immovable fixation of sash or frame, adjustable to different wood thicknesses, side stop in the rebate for the corner bearings, ergonomically arranged stop system for olive drilling with 14 swiveling stops and additional color markings, fixed stop system for drill hole height determination when changing from corner bearing to olive, automatic drilling depth sensing for corner bearing and olive, drill unit with quick-change chuck for the various tools for corner bearing and olive, tool change in "no time", automatic program sequence, clean work thanks to effective suction, small space requirement and mobile thanks to steering/brake rollers. Electrical equipment in accordance with VDE. Electrical connection: 0.55 KW, 400 V, 50 Hz. Pneumatic connection: R 3/8", 4 - 8 bar Extraction connection nozzle: 1 x 100 mm diameter Extraction speed: 25 m/sec. Space required: Csdpfxovu Hgzo Ah Usri Width: 2600 mm Height: 1250 mm Depth: 800 mm Support height: 300 mm Paint finish: RAL 7030 stone grey with RAL 1018 zinc yellow 1 drill set with 1 drill 25 mm and 2 drills 10 mm plus 1 drill 34 mm diameter (technical data according to manufacturer - no guarantee!)

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly Csdpfx Ahsv D Rg Ds Ujri on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction nozzle: 1930 mm Working...

Condition: used, cut-off saw 3 KW Spindle diameter 50 mm Spindle length 300 mm Number of tools variabel St. Control CNC Dimensions (L/W/H) 2500x1700x2100 mm weight 1700 kg HABERKORN - FZS-2 Electronic Slotting Machine with Stepless Slotting Spindles and Automatic Roller Table ----- Crosscut Saw ----- Spindle Positioned at the Top Three-Phase Motor 3 KW Spindle Diameter 30 mm Speed ??2800 rpm Saw Blade Diameter 400 mm * Automatic Brake with Speed ??Monitoring * Stepless Saw Positioning with Siko Display * Guard and Extractor Hood with 100 mm Diameter Extractor Nozzle 2 Slotting Spindles 50 mm Diameter ----- Power 2 x 7.5 KW Speed ??4200 rpm Spindle Diameter 50 mm Max. Tool Diameter Approx. 360 mm Usable Length 300 mm * Both slotting spindles can be positioned via ball screw * Freely programmable 19 programs, display with function keys * Protective and extraction hood with 180 mm diameter extraction nozzle Csdpfowgwlkjx Ah Ueri * Automatic brake with speed monitoring Studio table ----- * Swivel range +/- 65° * Automatically changing counter wood (programmable) * Pneumatic clamp * High-precision electrical degree indicator * Automatic length compensation * Counter wood at any angle setting in the cutting plane Special features ----- Continuously adjustable roller table feed Laser for workpiece positioning Manual length stop LA 2000 Length 2500 mm Extraction nozzle diameter: 2 x 180 mm for slotting spindles 1 x 100 mm for crosscut saw ----- Price of the above-mentioned machine upon request! ----- Images show the same model. Original images not yet available. (Technical specifications according to the manufacturer - no guarantee!) All prices quoted are net, plus statutory VAT.

Condition: used, Year of construction: 2013, Bore diameter , mm Number of heads horizontal , St. Number of heads vertical , St. 2 pcs. Götzinger drilling and milling centers ----- For sale on behalf of a customer! 2 identical machines: One machine for "left" parts and one for "right" parts. Crsdpfx Ajv N N Spoh Uji The machines can also be used individually. The machines were controlled via window manufacturing software, but can also be operated via the machine software. Both machines are equipped identically: - Left and right drilling units for front-end drilling. - 3 units for drilling and milling for longitudinal machining. - Parts are loaded once, and the unit carrier then moves for the various machining operations. Installation length per machine approx. 6 m. Individual sale possible: Price per machine 10,000 Euro See the enclosed PDFs for more information.

Condition: used, Working width 3550 mm Working height 2250 mm Number of cylinders 5 St. loading dimensions L x W x H 4500 x 900 x 2600 mm Hess Speedy frame press ----- Press will be Checked Insertion dimension / pressing length max. 3,550 mm Insertion dimension / pressing height max. 2,250 mm Sliding carriage for width adjustment locking in 50 mm Double hole grid system Electric height adjustment of the long-stroke cylinders (hydraulic) Crsdpfxjvn U Rne Ah Usi Insertion height of the abutment plates can be preselected in 4 positions 3 vertical printing cylinders stroke 1000 mm Pressure force per cylinder 2000 kN / 20000 N 2 horizontal printing cylinders stroke 80 mm Pressure force per cylinder 1250 kN / 12500 N Printing plate depth 100 mm width 140 mm Grid for cylinder fixation/rear bearing 50 mm Medium pressure beam with shut-off valve Final pressure switch-off and pressure control Control and pressing process in touch button operation Adjustable pressing pressure min. 25 – max. 160 bar Electrical connection 2.2 kW / 400V Control for studio window gluing 2 pendulum pressure plates 45 degrees Machine dimensions W=4500 mm, D=900 mm, H=2600 mm Weight approx. 1800 kg Photo and video not original, shows press of same type. (technical data according to the manufacturer - no guarantee!)

Condition: used, Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm control Weinig, PC-Nexus # 2764 Weinig Unicontrol 6 with NC spindles ----- Machine will be cleaned and completely checked before delivery Technical data summary (please enquire about any additional accessories included) Item 1: Cross-cut saw ----- > Electronic cross-cut saw, infinitely adjustable horizontally > Number of tools: 1 piece > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3.0 kW > Laser aiming light for detecting the saw section > NC length stop, mounted on slot table included Positioning of the cross-cut saw integrated in the control system. > Length 3500 mm Item 2: tenoning spindle ----- > Number of tools: variable, infinitely variable adjustment NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely variable adjustment 254 mm NC axis > Spindle speed: 3500 rpm > Spindle diameter: 50 mm > Max. tool diameter: 320 mm Cjdpfsvu Hfqex Ah Usri > Motor power: 11 kW Item 3: 1st profiling spindle (synchronous spindle and counter-rotation) > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Max. tool flight circle: 232 mm > Motor power: 7.5 kW Item 4: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, infinitely variable adjustment NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely variable adjustment 254 mm NC axis > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 11 kW 2 feed rollers opposite the spindle, axially pneumatically controlled, 2 positions Rung guide consisting of: Guide ruler in the stop (area of ??synchronous spindle), Rung support bar from above in the area of ??profile milling unit vertical right and profiling spindle. Pos. 5: Profile milling unit horizontal top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed ??5,850 rpm > Tool flight circle max. 130 mm > Axial adjustment range 30 mm, 8 positions using pneumatic turret > Radial adjustment range 125 mm, 8 positions using pneumatic turret Pos. 6: 3rd profiling spindle (fitting spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment range 115 mm, 8 positions using pneumatic turret > Radial adjustment range 100 mm, 8 positions using pneumatic turret > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Max. tool flight circle: 210 mm > Motor power: 3.0 kW Other features ----- > online-capable > rebating device for tear-free rebating > double parts package > return conveyor for 1-man operation: tilting belt > screen control > inclined window device > electronic angle display for inclined windows > industrial PC, PC control/NEXUS > Weinig type production program > without processing tools No original images available yet. Images show identical machines from our archive. ----- Price of the above-mentioned machine upon request! ----- Optional with additional charge: EUR 6.500,00 Note on used tools: We currently ha...

Condition: new, Working width 4500 mm Working height 3000 mm Number of cylinders 6 St. Dimensions (L/W/H) 5500x1400x3550 mm Weight 3000 kg S&S frame press Bavaria 2000 L ----- With automatic pressing cycle + manual control for corner connections tenon+slots and dowel connection/mortised tenon, can be switched using a selector switch on the control cabinet. With basic equipment for optional use of counter profiles if the sash is rebated on the loose part. CE version Basic machine in the strongest frame welded construction, with thick-walled special hollow profiles. Guideways of the pressure beams for the press corners in a low-abrasion machined version. Fast, smooth, manual width adjustment using ball-bearing carriage, fixing in 50 mm hole grid, optional motorized width adjustment with hydraulic clamping (at an additional cost). Height adjustment and pressing using long-stroke cylinders in one work cycle. Right-hand press corners with integrated horizontal cylinders, therefore no vertical positioning of the horizontal pressure cylinders is necessary, which avoids cylinder collisions. Lower support can be adjusted in several positions to the most suitable insertion height. 3 KW compact hydraulic system with integrated control block, variable pressure control from 20 - 120 bar, pressure gauge Control via touch button with separate control circuits for the vertical and horizontal press cylinders, mounted on a freely movable control panel. 2 vertical press cylinders, double-acting, stroke adapted to working height, piston diameter 60 mm Pressure force per cylinder max. 2100 kg Cedpewg Hr Tjfx Ah Ujri 2 horizontal press cylinders, double-acting, 80 mm stroke, piston diameter 40 mm Pressure force per cylinder max. 1250 kg Abutment and pressure plate depth 100 mm Control cabinet on the machine base on the left, 400 volts, 50 Hz Machine with ready-to-connect plug 16 A Paint: RAL 7035 light gray with RAL 7016 anthracite gray Working size: length x height = 4,500 mm x 2,750 mm Note: Actual working size: 4,500 x 3,000 mm (length x height) Space required: 5,500 mm x 1,400 mm x 3,550 mm (LengthxWidthxHeight) Article medium pressure bar complete with pressure cylinder, pressure hose and shut-off valve up to 2,750 mm high Note: actual working height: 3,000 mm Article Individual pressure control for medium pressure bar, pressure control range up to max. 100 bar (For pressing cross-bar windows) Article infinitely height-adjustable cross pressure device, complete with pressure cylinder and abutment, throttle and shut-off valve Article Individual pressure control for cross pressure device pressure control range up to max. 100 bar (For pressing cross-bar window) Article Shut-off valve on the 3rd vertical cylinder Article Shut-off valve on the upper horizontal cylinder Article x slanted window control for vertical cylinder Article x pendulum pressure plates attachable for pressing up to 60 degrees Article Double pendulum pressure plate for pointed window (triangle) Article x extension for p...

Condition: used, Tenoning spindle 1 St. Number of milling agregates 0 St. Crsdpsxa Hi Nefx Ah Usi Spindle diameter 40 mm Small window production consisting of: W. ----- 1) Haberkorn FZS1 slotting machine 2) Okoma SF3F table milling machine 3) Oertli tool for the Haberkorn and Okoma machines Wooden windows 1 set IV 68/78/88 and 1 set wooden aluminium windows IV 68/78 built in 2011 4) Götzinger OBM Plus corner bearing and olive drilling machine, Maco MultiMatic fittings ----- Technical manufacturer's description: - Haberkorn FZS1 slotting machine with automatic feed, -stepless height adjustment D 40 mm Cutting-to-length saw: -Spindle arrangement: top -Three-phase motor: 3 kW -Spindle diameter: 30 mm -Speed: 2800 rpm -Saw blade diameter: 400 mm -Automatic brake with speed monitoring -Horizontal pneumatic positioning, manually adjustable -Protective and extraction hood with extraction nozzle diameter: 100 mm Slotting spindle D 40 mm: -Power: 7.5 kW -Speed: 4200 rpm -Working length: 252 mm -Max. tool diameter: 340 mm -220 mm stroke, infinitely variable height adjustment via precision ball screws -Protective cover and extraction hood with extraction nozzle diameter: 180 mm -Automatic brake with speed monitoring Studio table: -Swivel range +/- 65 degrees -Automatically changing counter blade (programmable) -Pneumatic clamp -High-precision electric degree display -Automatic length compensation -Counter blade for every angle setting in the cutting plane Special equipment: -Laser for workpiece positioning -Pneumatic saw position -Length stop LA 2500 mm + 1850 extension ----- 2) Okoma SF3F table milling machine with lifting spindle, 3 tools -Suction connection nozzles 2 x 120 mm -Spindle length 270 mm -Counter stop ruler with fine adjustment and turret head -Triple stroke, cycle height max. 90 mm -Glass bead cutting saw with protective and extraction hood 80 mm diameter -8 roller feed device with stand and hold-down arm, required for glass bead cutting saw setup -Pneumatically controlled pouring device for edge gear, speed 6000 rpm -2x 3kW motor -Mounting diameter 30 mm ----- 3) Oertli tool for Haberkorn and Okoma machines -1 set of wooden windows IV 68/78/88 -1 set of wood-aluminium windows IV 68/78 Sale of tools in the condition, scope and with accessories as available in our warehouse. Note on window cuts, tool drawings, tool system listings: Engelfried does not guarantee that the tools actually available correspond to the systems mentioned and drawn. ----- 4) Götzinger OBM Plus corner bearing and olive drilling machine -Corner and shear bearings + handle olive drilling -Vertical drilling unit with: -Quick-change drill head device -Pneumatic feed via foot valve -1x olive drill head 24 mm -1x corner bearing double head -Maco MultiMatic fitting -1x adjustable folding stop on the left with 6 stops -1x adjustable folding stop on the right with 6 stops -1x machine stand complete with shelf -220/400 V, 60 Hz, 1.3 kW -1x roller conveyor approx. 1 m long with 2 rollers -1x roller conveyor approx. 1.5 m long with 3 rollers ----- Price of the above machines on request! Plus packaging and shipping ----- (Technical data according to manufacturer - no gua...