Condition: excellent (used), Year of construction: 2011, functionality: fully functional, Unicontrol 12 Consisting of: Cut-off unit (item A), Tenon and slotted spindle (item C), Transfer belt (Pos. I), profiling spindle (Pos L), profiling spindle (Pos. N), Profile shaving unit vertical right (Pos. P) For the production of individual parts and elements in frame-by-frame or serial production. Consisting of a cross processing unit and a longitudinal processing unit connected to a transfer belt. Working width 40-140mm (See pressure ruler left 40 - 140 mm) Working height 40-120mm Workpiece length min. approx. 275 mm + 1 x end profile length Long machining: approx. 220 mm + 2 x end profile length Workpiece length max. 3500 mm The part dimensions depend on the machine equipment, production type and tool assignment. A final definition of the part dimensions is only possible after receipt, inspection and approval of the complete and final layout drawings. Cross machining: Table feed Motor power 0.3 kW (0.4 HP) Pre-set feed speed for cutting, profiling and return 3-25 m/min Vario table with (studio window production possible) The clamping length of all tenoning and slotting spindles can be used without a tool blank. Workpiece clamping by means of a clamping bridge. Operated by a clamping cylinder installed under the table. NC-controlled long fence mounted on the slotting table. Studio window device Swivel angle max. +/- 75° The minimum workpiece length for slanted windows depends on the angle and the width of the wood. Possible part dimensions for slanted window production Angle Max. Min. Working width Workpiece length +/-75° 80 mm 800 mm +/-70° 120 mm 490 mm +/-60° 240 mm 360 mm +/-90° 350 mm 185 mm For angles greater than 60° only counter processing Commission not documented Iisdpfx Asumci Ssgzek 1)NC automatic angle adjustment for machining angled parts Splinter protection by means of overtravel counter Over the entire spindle length of the tenoning and slotting spindle for 90° machining Manually trackable counter-rail for angled part machining 2) Additional counter-rails

Condition: used, Year of construction: 1992, Used machine Year of manufacture: 1992 Technical specifications: Length of jointer table: 2100 mm Diameter of tool spindle: 30 mm Diameter of planer heads: 100 mm Planer spindle speed: 6000 rpm Working width: 30 - 180 mm Iedpexgkf Usfx Agzjik Working height: 6 - 120 mm With an optionally available smaller planer head for the left spindle plus narrower feed rollers, a minimum width of 15 mm can be achieved Motor power bottom, left, right: each 3.7 kW Motor power top (thickness spindle): 5.5 kW Feed speed: 6 and 12 m/min Electric height adjustment With 1/10 increment control Including step-controlled feed roller Including planer heads Extraction ports: 160/120/120/140 mm Availability: short-term Storage location: Flörsheim

Condition: used, Dimensions (L,W) , mm Weight ca. 90 kg adjustable height (yes/no) ja stroke 300 - 800 mm surface of working table 1.700 x 1.500 mm table width max. 3.800 mm 0 ca. 130 kg Ruchser RU-4-SSP rotary-tilt table ----- Support surface 1700 x 1500 mm, maximum Table width swung out 3800 mm, pneumatically tiltable, weatherproof recess, with 6 storage boxes, each with 2 compartments, pull-outs below for widening, with 2 support feet and 2 flat clamping cylinders, Lifting device from 300 - 800 mm, Roller conveyor as a surface, foldable. Payload capacity 130kg. Driving device with 4 swivel castors Stop device (RU-4SSP) 2 stops for final inspection and To seal Wing assembly device with tool tray and adjustable stop for Inclination for RU-4-SSP Holder for drill, screwdriver gun etc. with screwdriver quiver Driving device with flanged rollers RU-DKFA and RU-4SSP Iedpfx Agjvu Hfdszeik 3 double meter rail for Driving device 25 x 10 mm ----- Price of the above machine on request! plus packaging and shipping ----- (technical data according to manufacturer - no guarantee!)

Condition: used, Working width 4000 mm Working height 2600 mm Number of cylinders 6 St. Dimensions (L/W/H) 5300 x 1250 x 3330 mm S&S frame press type RP 2000, ----- C E - version Stable frame welded construction made of thick-walled special hollow profiles, Sliding carriage and pressure bar with 50 mm hole pattern. Continuous abutment on the left for width compression, lower abutment in two levels. Vertical press cylinder on special pressure bar with one-hand quick adjustment with weight compensation in the 50 mm hole pattern, height-adjustable, long Sliding carriages ensure the permanent absorption of high pressing forces. Fast, smooth width adjustment with ball-bearing carriage Central locking, fixation in 50 mm hole pattern. Upper horizontal press cylinder infinitely adjustable in height and with Equipped with counterbalance. Lower horizontal press cylinder with center holes for the two Abutment levels, with weight compensation. Abutment and pressure plate depth 100 mm Printing plate and support width 130 mm Machine electro-hydraulically controlled, with 2 vertical pressure cylinders d = 50 mm, stroke 120 mm double-acting, with counterweight and One-hand quick adjustment, 2 pieces Horizontal pressure cylinders d = 40 mm, stroke 120 mm double-acting, with weight balancing; 2 manual control valves, Pressure gauge, 1 pressure control valve from 20 to 125 bar corresponds to 400 to 2400 kg pressure vertical, with 3 kW three-phase motor for 400 volts, 50 Hz operating voltage. Complete with electrical connection. Paint finish: RAL 7035 light gray with RAL 7016 anthracite grey Working size: 4000mm x 2600mm (length x height) Required space: 5300 x 1250 x 3330 mm (L x W x H) Machine including the following options: ----- Article .00 pc Medium pressure bar with pressure cylinder double-acting, weight compensation, pressure hose and shut-off valve up to 2600 mm high Article .00 pc Individual pressure control for medium pressure bar, Pressure control range up to max. 100 bar (for pressing crossbar windows) Article .00 pc Cross printing device complete with pressure cylinder double-acting, weight compensation, pressure hose and shut-off valve There is no weight compensation on the lower horizontal cylinder Article .00 pc Individual pressure control for transverse pressure device, Pressure control range up to max. 100 bar (for pressing crossbar windows) Article .00 pc Shut-off valve on the 3rd vertical cylinder Article .00 pc Shut-off valve on the upper horizontal cylinder Article .00 pc Width allowance for compression of small frames to bridge the 1st pressure beam, including shut-off valve on the 1st vertical cylinder Article .00 pc Basic equipment for counter profiles The space required in height increases by 100 mm Item All pressure plates and abutments covered with plastic Article .00 pc Triangle studio window pressing device consisting of: locking device of Vertical pressure bar and 3 attachable, side-guided pendulum pressure plates Article .00 pc double pendulum pressure plate for pointed windows (triangle) ----- Iiodpfju Uvalsx Agzek Total price in the above version ex works: On request! ----- Options: Article ....

Condition: new, Bore diameter variabel mm Number of heads horizontal 1 St. Number of heads vertical 0 St. 1 Götzinger dowel gluing and insertion machine BLE With the BLE, the workpieces are glued and dowelled on the front. Optional the BLE can be upgraded with a drilling unit, counter milling unit and longitudinal stop will. A 10" touch panel allows easy operation for manual or online operation. Base frame: in a compact design, covered with sheet metal Table support approx. 800 x 200 mm position 1 ----- 1 glue station full jet valve Glue quantity precisely adjustable Glue gun for counter hole gluing position 2 ----- 1 stainless steel glue pump, high-pressure pump and glue hose item 3 Iodeu Uu Uzopfx Agzjik ----- 1 press-in station with dowel separation and press-in cylinder item 4 ----- 1 oscillating conveyor for dowels d 8 x 50 mm with feed hose into the injection unit item 5 ----- 1 processing unit with cross table, linear guide and 3NC axis motors X = 200 mm processing width Y = 120 mm processing height Z = 50 mm offset item 6 ----- 1 positioning controller Touch panel 10" color 500 drilling patterns can be created and saved, which can be easily accessed when needed (1 drilling pattern can have up to 16 dowel positions) Software prepared for ONLINE connection With online control, the data for the control must be provided by the software be prepared. Our machine can then read and process this data. ----- Total price in this version Pos. 1 to Pos. 6: on request! Options with additional prices: ----- item 7 ----- 1 horizontal drilling unit, 1,000 W drilling motor Speed ??4,000 - 8,000 rpm, collet holder Pneumatic drill feed Surcharge: EUR 4,305.00 Additional accessories such as a larger touch screen, additional dowel station for additional dowel sizes or scanner for Program selection on request! Prices net plus statutory VAT, without packaging/shipping and without Installation. (technical data according to the manufacturer - without guarantee!)

Condition: new, Working width 3500 mm Iiodpfxsd Ih H Ss Agzok Working height 2300 mm Number of cylinders 4 St.

Condition: used, max. tool diameter , mm 0 , mm operating pressure , bar filling amount 52 l Quicksonic QS 520 Ultrasonic cleaning device with lid and work basket ----- Technical manufacturer's description: External dimensions (length x width x height): 560 x 460 x 510 mm Useful dimensions (length x width x height): 500 x 400 x 260 Useful basket dimensions (length x width x height): 444 x 364 x 224 Capacity: approx. 52 l Ultrasonic power Iisdpfoumng Aex Agzjk Rated power: 800 watts Peak power: 1600 watts Operating frequency: 40 or 25 kHz Mains voltage: L+N+PE, 230 V/50-60 Hz Heating power: 2000 watts Heating control: 30 - 85°C Timer: 0-15 min & Duration ----- All prices ex works plus packaging, transport, insurance, and statutory VAT. (Technical specifications according to the manufacturer - without guarantee!)

Condition: new, Working width 3500 mm Working height 2300 mm Number of cylinders 4 St. Stable frame welded construction of thick-walled Special hollow profiles , sliding table and pressure beam with 50 mm hole pattern . Iiodpfx Aed Ih H Njgzjk On the left side continuous abutment for grouting the wide , lower abutment in 2 levels. Vertical pressing cylinder on specialty bar with one- quick adjustment with weight compensation in the 50 mm hole pattern adjustable in height. Long sliding table ensure the continuous recording of high jacking forces . Fast, smooth width adjustment with ball bearing Carriage with central fixation in 50 mm hole pattern. Upper horizontal press cylinder infinitely adjustable in height and equipped with counterbalance . Lower horizontal pressing cylinders with bore for two abutments levels without weight compensation . Abutment and pressure plate depth 100 mm Machine controlled electro -hydraulic with 2 pieces vertical pressure cylinders d = 60 mm, stroke 120 mm, single-acting, with counterbalance and One-hand height adjustment, 2 piece horizontal pressure cylinders d = 40 mm stroke, 120 mm single-acting ( 1 x with weight compensation ), 2 hand control valves , Pressure gauge, pressure regulator valve 1 of 20 to 150 bar corresponds to 550 4200 kg compression force vertically. With 3 kW three-phase motor for 400 volts , 50 Hz Operating voltage. Complete with electrical connection . Painting RAL 7035 anthracite gray with light gray RAL 7016 . (technical details according to manufacturer - without guarantee ! ) The detailed technical description can be found in the attached pdf file

Condition: new, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 2004 ----- Double-sided four-belt single wood sander for Sanding solid wood such as window frames etc. Highly stable top design with innovative details. Suitable for high continuous loads even with higher chip removals. - sanding units arranged one after the other for pre-grinding, Fine sanding and finishing sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberized roller and shoe 3. Finishing unit with fiber brush - Directly driven grinding rollers for slip-free Power transmission - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction Iisdpfx Agsvnv Tqozjk - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, cast tables Finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor with stepless speed 4-20 m/min - all motors electrically protected - ergonomically arranged controls - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Grinding thickness 2-180mm - four brake motors for 5.5 kW drive - Feed motor 1.5 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m/s - Pneumatic connection 6 bar - Working height 870mm - Length (with soft disc 2740mm) 2600mm - Length with control panel (with soft disc 3035mm) 2985mm - Width 880mm - Height 1910mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional charge: Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled 4-belt sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Di...

Condition: new, Number of sanding units 2 St. sanding width 190 mm Sanding height max. 2-180 mm LÖWER double-sided grinding machine DSM 2000 ----- Double-sided single wood sander for sanding Solid wood such as window wood etc. Stable top quality Guide with long casting tables, brushing and finishing equipment and conveyor belt feed. Suitable for high continuous loads even with higher chip removals. - Staggered sanding and finishing units at the top and bottom - Directly driven rubberized grinding rollers for slip-free power transmission - Combined grinding via roller and shoe for high chip removal at the same time flat intervention zone - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and higher grinding Grinding belt service life - Forced pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the sanding rollers Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom using a precision threaded spindle Dimension display via scale ring (resolution 0.1mm) - Sanding belt tension via pneumatic cylinders with constant clamping pressure - Sanding belt change with pneumatic belt relaxation in seconds - Adjustment of the sanding belt run when changing the belt - electro-pneumatic compressed air monitoring - Run-in protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and non-stick conveyor belts over heavy, 1000mm long cast tables with a finely planed surface and Spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and even workpiece transport - Feed gear motor with three different feed speeds for quick adaptation to different types of wood - all motors electrically protected - Ergonomically arranged controls on the workpiece inlet side - automatic workpiece thickness scanning (no previous measurement necessary) - Digital thickness display (resolution 0.1mm) with modern magnetic tape system Technical data: - Sanding belt speed: 22 m/s Iiodpfx Agovu Hdtezok - Sanding belt length: 1800mm - Sanding belt width: 200mm - Working width: 190mm - Grinding thickness: 2-180mm - two brake motors for drive: 5.5 kW - Feed motor: 1.0 kW - Feed speed: 6, 11 and 16 m/min. - automatic height adjustment: 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle: 2 x 120mm and 2 x 150mm - Pneumatic connection 6 bar - Working height: 850mm - Length: 2105mm - Length with control panel 2490mm - Width: 880mm - Height: 1910mm - Weight: approx. 1500 kg - Operating voltage: 400 volts, 50 Hz, 3P - CE version ----- ----- Basic price of the machine on request! ----- ----- Special accessories with surcharge: continuous feed 4-20 m/min. for speed adjustment to the previous machine Price on request Workpiece blow-off - using nozzles from above and below at the machine ...

Condition: new, Working width 3500 mm Iijdped Rzc Rsfx Agzjk Working height 2300 mm Number of cylinders 4 St.

Condition: used, Length 2700 mm Width 1100 mm Height 850 +- 150 mm engine output 0,37 kW Ijdpfx Agjnl Nqqjzjik Electric capacity 0,5 kw compressed air 6 bar Horizontal impregnation system 'Pro flow' for individual parts with rinsing circuit. ----- Features: Machine for horizontal flooding of individual parts. The product will go through flooded a row of nozzles. The excess product is then removed through air jets blown off. The pump and the air nozzles are controlled automatically and only then operated when the workpiece passes through. In this way the Compressed air consumption reduced. The circulation operation ensures minimal product consumption. ----- Construction features: structure Sturdy steel frame, painted with high-strength, water-soluble products. Machine body made of heat-sealed, thick polypropylene plates. 4 independent chambers for inlet, flooding, blow-off and outlet. Horizontal feed of the workpieces By motor-driven rollers made of plastic with grooves. Electrical converter for controlling and changing the conveying speed. transmission The machine is equipped with an exclusive system so that all Gear located outside the flood chamber and easily accessible to the Operators are to guarantee a longer service life and the to facilitate maintenance operations. The moving components are protected by cover plates and appropriate seals protected. circulation pump Pneumatic double diaphragm pump made with valves, seals and diaphragms Nitrile rubber and housing made of plastic material (PVDF). air jets A blow-off system is present in the first chamber to prevent product leakage avoid. A second blow-off system after the flood chamber blows off the excess product from the workpiece. Electrical panel According to CE, degree of protection IP 55. Including inverter to the set feed rate. technical features Length mm 2700 Width mm 1100 Conveyor speed (min./max.) m/min 3-6 Motor power train group kW 0.37 Installed electrical power kW 0.5 Distance between infeed and outfeed rollers mm 2520 Working height (adjustable) mm 850 +- 150 Min. length of the workpieces to be flooded mm 250 Max. width of the workpieces to be flooded mm 300 Max. height of the workpieces to be flooded mm 250 Compressed air consumption lt/min 2000 Pressure of the required compressed air bar 6 Equipment and available accessories Flushing circuit for Pro Flow ----- Price of the above machine: on request! plus packaging and transport ----- (Technical information according to the manufacturer - without guarantee! Illustrations may be dated Deviate from the original, prices net, plus VAT (domestic))

Condition: new, Number of sanding units 8 st. sanding width 180 (260) mm Sanding height max. 160 mm Dimensions (L/W/H) 3065x1600x1900 mm weight of the machine ca. 1500 kg LÖWER Leistomat SD ----- Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm 1 softisc unit Ø=200mm above 0.75kW, 1 slat roller unit L=200mm top 0.75kW, 1 soft disc unit Ø=200mm bottom 0.75kW, 1 slat roller unit L=200mm bottom 0.75kW, 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm - Linear guidance of all grinding units Linear ball bearing sets on hardened shafts - time-controlled immersion of all lamella roller units directly above the incoming workpiece edges. By the It is possible to immerse the aggregates deeper into the profiles to be able to deliver. - Motorized workpiece thickness adjustment of the machine - variable grinding flap speed via frequency converter for adjusting the grinding intensity using frequency converters (separate for discs, surface rollers and side rollers) - Disc aggregates as soft discs with Velcro fastener for Grinding wheels (wood pulp) - Feed via three lower and one upper conveyor belts and Spring-loaded pressure rollers with infinitely variable speed 4-15m/min - Parameters that can be set using the touch panel are workpiece thickness, Workpiece width (left side units individually), immersion depth Side units, spindle speed, feed speed - Saving the parameters as machine programs in program mode - Working in automatic mode with non-contact Workpiece width detection and profile detection as well as automatic Adjustment of the sanding units to the workpiece width and the Profile shape (workpiece height is set in advance) - pneumatically clocked driven feed roller, automatic Clamping of the workpiece and feeding in after unit adjustment - Red/green indicator lights to indicate operational readiness - shortest workpiece length 380mm - Transport belt width 200mm - max. workpiece width 180mm (260mm in the envelope process) - Workpiece height 12-160mm - Suction connection 4 x 100mm and 2x80mm diameter - Sensor-controlled tool blow-off directly on the discs - Length (case) x width x height (mm): 3065x 1600 x 1900 Complete length: 4365mm (including roller conveyor with integrated workpiece width detection) - Weight: 1500kg - Operating voltage 400V, 50Hz, 3P, air connection 6 bar - CE version ----- Price of the above machine on request! ----- Special accessories with additional costs: Set of replacement slats for Leistomat SD-200 consisting of Area aggregates: 30 strips EH45 / 200 - 7 (rolls) 30 strips EH45 / 200 - 20 (rolls) Folding units: 96 strips M55 / 120 - 4 Isdpfxjvnv Uhe Agzoik SmartFlex slat disc Ø200 solid with 30 grooves 50mm long Set of replacement slats for SmartFlex slat disc consisting of 60 strip M35 / 50 K 180-7 p Sandpaper disc VB for soft disc D=200mm grit 220 with velor backing (Velcro), pack of 100. Sandpaper disc VB for soft disc D=200mm grit 280 with velor backing (Velcro), pack of 100. ----- Price of the above-mentioned special accessories on request! -----...

Condition: new, Bore diameter variabel mm Number of heads horizontal 3 St. Number of heads vertical 4 St. weight 1500 kg Dimensions (L/W/H) 4800x1600x2400 mm Width mit Auflage 2300 mm Götzinger Power Drill Type BF 297 With the Götzinger PowerDrill you can, depending on the type and design: Griffoliven drill on the loose frame part or for finished wings, with multi-spindle drilling head, quick-change, also for milling of the lock case for WK 2 or intermediate gear Ecklager drill on loose frame part, with Mehrspindelbohrkopf, quick-change, corner-oriented over stop or custom made (tilt window) Drill vertically from above for fitting, pre-drill for clip on loose frame part Milling vertically from above for pushers, profile cylinders, 3-D hinges Horizontal drilling with 2 drilling units, different drilling diameters, Dowel drill front and long side, plywood / fighter, sprouts, Corner connection, front door etc. Milling horizontally for lock case / fitting etc. Iiodpfx Agjd Ih Hqozjk machine description Base frame in stable welded construction, linear guide for the X-axis Table top 3,000 x 200 mm 6 clamping cylinder pneumatic with auto. Ausweichhub 2 side stops for machining on the front side, manually swiveling in and out 2 longitudinal stops can be manually swiveled in and out Travel: X-axis - 3,000 mm working length Y-axis - 120 mm Z-axis - 105 mm Aggregate: 1 drilling unit (unit 1) vertically from above, drill motor 1,1 KW Speed ??1,500 - 12,000 rpm, 1 spindle, collet holder ER 20 1 Bohraggreagt (unit 2) vertically from above, drill motor 1,1 KW Speed ??3,000 rpm, with drill head quick change device 1 boring head BKF 3, olives, quick-change 1 boring head BKF 3/2 corner bearing, quick-change 1 milling unit (Agg.3) vertically from above, milling motor 2 KW, 1,500 - 16,000 rpm, collet holder ER 25 2 horizontal drilling units (Agg.4 and 5) 1.0 KW, 1.500 - 12.000 U / min, Collet holder ER 20 1 milling unit horizontal (Agg.3) 2.0 KW, 1.500 - 16.000U / min, Collet holder ER 20 Electro-pneumatic control with 3-axis control X, Y, Z NC positioning controller make B + R input via TFT display 10 " Machine complete with 1 set of drilling tools dm 6, 8, 10 and 12, 2 roughing carbide cutters HM dm 16, CE compliant, ready for connection Suction connection: 1 x dm 120 Power connection: 1 x 400 V, 16 amps Air connection: 1 x LW 9 mm OPTION: Longitudinal stops right / left with NC axis high / low programmatically, thus dimension input by folding / light measure possible, Dimension: LxWxH = 4.80 x 1.60 x 2.40 m - weight machine 1,500 kg (technical data according to manufacturer - without guarantee!)

Condition: new, Assembly line consisting of: Item 1.0 / RU-CBM 4000 work table with running rail extended by 500mm for additional assembly an aluminum holder screwing machine for RU-CSA-SMB or RU-CSA-SMZD with RU-SH special screwdriver, support table Length 4000 mm, width 1400 mm, inclination of the working platform manually adjustable. Holder for fitting scissors or fitting punch. 16 pieces of swiveling counter-holders for hanging the wings, completely pneumatic Foldable for unhindered movement of the wings on the table surface. Device for scanning the sash fitting length for constant and variable/central gear seat for already drilled wings, colored Dimension recognition of the fittings. RU-SH, special screwdriver with pneumatic depth switch on carriage mounted, safety control, pneumatic height adjustment, Screw feeder with automatic shutdown of the filling container (Manual insertion for a second screw length on the special screwdriver upon request). RA-8, turret stop for 8 screw levels mounted on the carriage. Ijdjd Ih Huopfx Agzeik RA-4, turret stop for 4 different wing widths Swivel table mounted. Pneumatic wing measurement sensing. operated, scanning range up to 2500mm simultaneous clamping of the scanning. PSF - Pneumatic tensioning device for sashes. Working height adjustable from 900 - 1000 mm. Support table covered with felt. Running rail extended to the left by 800 mm. Item 1.1 / 5035-1 Pneumatic swivel device of the work surface with foot valve Item 1.2 / 0500000 Holder matched to customer punch/scissors. For mounting a hardware punch provided by the customer or Fitting shears (third-party manufacturer) on the sash assembly table. Please specify make when ordering!!! Item 1.3 / 5597-7 Driving device for RU-CBM on semicircular rails. The castors are on the left and right of the base frame of the table mounted. Item 1.4 / 6354-6 3 double meters of semicircular rails 30 x 10 mm. Item 1.5 / 0730000 RU-SBL3000/40 free-standing fitting bearing, Length 3100 mm, depth 1250 mm, height 2200 mm, Stand frame on the front without supports, 40 compartments, divided into 10 compartments in a row by dividers and a continuous shelf at the top, Compartment size: width 280 mm, height 150 mm. Item 2 RU-CSA-SMB aluminum holder screwing machine with automatic Screw feeding and manual feeding of the aluminum holders from one traveling box with pneumatic positioning device, Screwdriver with depth cut-off with 4-fold turret stop. Pneumatic adjustment device in the y direction against 2 pieces 6-fold Revolver attacks. Feed container for manual feeding of rotary holders or clip holder in square shape 18.5 x 18.5. The holder is manually pushed into a channel in the box and with positioned in front of the screwdriver mouthpiece using a pneumatically operated slide. Profile depth max. 150 mm, screw spacing in the y direction max. 120 mm. Item 3 RU-S48-A6-350 column slewing crane for chain hoist, with 6 m aluminum boom Version with column, smooth-running boom and sliding chassis for swivel and trolley travel manually by pulling and pushing the load. Projection 6 m Construction height 4,461 m Lower edge of boom 3.722 m (top edge of boom 3.9 m) Swivel range max. 270° Painting of the steel construction in RAL 7035 The base plate is attached to the on-site hall floor At least 250 mm thick. Designed, of course, according to the valid STANDARD EN 13155 Warra...

Condition: used, Working width 3600 mm Working height 2600 mm Number of cylinders 5 St. loading dimensions L x W x H 4400 x 1150 x 2970 mm weight 3000 kg Schafberger + Sproedhuber Bavaria Frame Press ----- Machine is overhauled by us before delivery. With automatic pressing cycle + manual control for tenon + slot corner joints. CE-certified version Basic machine in the strongest welded frame construction, with thick-walled special hollow profiles. Guideways for the pressure beams for the press corners in a low-wear machined design. Iiedpfjw T Un Uex Agzek Fast, smooth, manual width adjustment via ball-bearing carriages, fixed in a hole pattern. Height adjustment and pressing via long-stroke cylinders in a single work cycle. Right-side press corners with integrated horizontal cylinders, therefore no vertical positioning of the horizontal pressure cylinders necessary, thus avoiding cylinder collisions. Lower abutment adjustable in several positions for the most favorable insertion height. 3 vertical press cylinders, double-acting, stroke adjusted to working height 2 horizontal press cylinders, double-acting Abutment and pressure plate depth 80 mm Working size: Length x Height = approx. 3,600 mm x 2,600 mm Space requirement/loading dimensions: approx. 4,400 mm x 1,150 mm x 2,970 mm (Length x Width x Height) Option: ALWA pressing supports for sloped windows (Technical specifications according to the manufacturer – no guarantee! Images may differ from the original. Prices are net, plus VAT (domestic))

Condition: new, Year of construction: 2025, Number of motors 2 Stück 0 3000 mm Control ja/CNC loading dimensions L x W x H 4000 x 1500 x 1500 mm Weight 800 kg HECHT double miter saw Exenso DS350E - 3000 mm ----- For wooden glass strips, rungs, profile strips, aluminum strips, etc. Pos. 1.1 Article number 942.5103 1 piece HECHT Exenso DS350E - Working length 3000 mm - Swivel range 22.5° (inside) to 135° (outside) - Right head movable - Saw blade holder Ø 350 mm - Incl. 1 piece center support. - Units clamped pneumatically. - Positioning control Exenso DS3 with touch panel 15" display in dust-proof monitor housing. - 3-axis control, 1 longitudinal axis and 2 swivel axes. - Entering the cutting data by hand - Processing data from a cutting list (data set according to specification) - Processing measuring rod data (GMF wireless caliper) - Ethernet connection 10/100 (TCP/IP) - USB interface - Incl. control cabinet, motor and software licenses. Item 1.2 Item number 723.0121 2nd DS saw blade wood Bevel/bevel/flat tooth - positive Item 1.3 Item number 942.5236 2 sets of DS workpiece clamping combined Combined workpiece clamping consisting of: Pneumatic swivel clamp - for clamping the material from above. (Free access to the work table) Pneumatic horizontal clamp - anti-twist clamping cylinder with pressure piece. The clamps can be selected individually via the saw control. The clamping sequence can also be set via the control. Including safety pre-tensioning pressure Scope of delivery for 2 sets: - 2 pieces (left/right) vertical swivel clamps. - 2 pieces (left/right) horizontal clamps. Item 1.4 Article number 942.5997 DS pneumatic feed device Item 1.5 Article number 945.2007 Packaging DS350 (transport frame) ----- Total price in this version - on request! ----- ALTERNATIVE options, prices on request! ----- For horizontal clamping of the remaining pieces with blunt glass strips instead of the 2nd set Item 1.3 943.5236 DS workpiece clamping combined! Pos. 2.1 Article number 942.5201 ES / DS workpiece clamping from the front - 2 clamping cylinders with anti-twist protection - 2 cylinder holders with clamping lever ----- For rebated glass strips, instead of standard panels without a groove: Pos. 2.2 Article number 942.5241 DS350 table supports grooved according to customer sample The assembled table supports are milled according to the customer's drawing. Please send us all profile drawings that are to be sawn (pdf, dxf and hand samples) ----- If, for example, aluminum is also to be sawn: Item 2.3 Article number 942.5203 DS hydropneumatic feed device (instead of pneumatic feed cylinder) ----- OPTIONAL accessories, with additional charge on request: ----- Item 2.4 Article number 942.5237 DS "Excess length" software (subsequent steps must be confirmed) Sequence control including hardware. After entering a cutting dimension > max. cutting length of the system, the cutting is carried out in a cyclical manner. (Left unit cuts, right unit moves the material and cuts to size.) ----- Item 2.5 Article number 944.1023 GMF caliper 3000mm complete set (1500mm plus extension 1500mm) Iodpsvzt D Tjfx Agzeik incl. charger and receiver. A robust aluminum measuring rail with a measuring ran...

Condition: new, Number of spindles 6 St. Working width 250 mm Working height 150 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-24 m/min. weight 4770 kg Dimensions (L/W/H) 4722x1860x1776 mm Vierseitenhobelmaschine Kuper SWT XL-6 in Fenster-Version mit elektronischer Axial- und Radialverstellung der Spindeln. Schwerer Maschinenständer, verwindungsfrei und schwingungsarm. Anzahl der Spindeln: 6 Arbeitsbreite: 250 mm Arbeitshöhe: 150 mm Abrichttischlänge: 2500 mm Spindeldrehzahl: frequenzgeregelt 4.000 - 8.000 U/min Vorschubgeschwindigkeit: 6-24 m/min Iijdpfxjvnv Ubs Agzjk Ausführliche Beschreibung finden Sie in nebenstehender PDF-Datei! (Technische Angaben laut Hersteller - ohne Gewähr!)

Condition: used, cut-off saw 3 KW Spindle diameter 50 mm Spindle length 300 mm Number of tools variabel St. Control CNC Dimensions (L/W/H) 2500x1700x2100 mm weight 1700 kg HABERKORN - FZS-2 Electronic Slotting Machine with Stepless Slotting Spindles and Automatic Roller Table Iiodewgwlkopfx Agzjk ----- Crosscut Saw ----- Spindle Positioned at the Top Three-Phase Motor 3 KW Spindle Diameter 30 mm Speed ??2800 rpm Saw Blade Diameter 400 mm * Automatic Brake with Speed ??Monitoring * Stepless Saw Positioning with Siko Display * Guard and Extractor Hood with 100 mm Diameter Extractor Nozzle 2 Slotting Spindles 50 mm Diameter ----- Power 2 x 7.5 KW Speed ??4200 rpm Spindle Diameter 50 mm Max. Tool Diameter Approx. 360 mm Usable Length 300 mm * Both slotting spindles can be positioned via ball screw * Freely programmable 19 programs, display with function keys * Protective and extraction hood with 180 mm diameter extraction nozzle * Automatic brake with speed monitoring Studio table ----- * Swivel range +/- 65° * Automatically changing counter wood (programmable) * Pneumatic clamp * High-precision electrical degree indicator * Automatic length compensation * Counter wood at any angle setting in the cutting plane Special features ----- Continuously adjustable roller table feed Laser for workpiece positioning Manual length stop LA 2000 Length 2500 mm Extraction nozzle diameter: 2 x 180 mm for slotting spindles 1 x 100 mm for crosscut saw ----- Price of the above-mentioned machine upon request! ----- Images show the same model. Original images not yet available. (Technical specifications according to the manufacturer - no guarantee!) All prices quoted are net, plus statutory VAT.

Condition: used, Number of spindles 4 St. Number of tools 11 St. Spindle diameter 50,40 mm Spindle length 285,125 mm length 4000 mm width 2000 mm height 2200 mm Weinig Univar 10/3 folding machine ----- Iijdpjvnv Uujfx Agzsk For milling around windows, doors and the like with uneven circumferential profiles. Machine suitable for wood thickness 68 to 92 mm Time required per frame milling, medium size 1.20 x 1.20 m - approx. 2 minutes. The available tool positions are selected using a selector switch on the control panel retrieved. Machine with 3 hydraulically controlled right precision Lifting spindles for holding 3 tool sets, 2 x 95 mm spindle stroke per spindle The spindle stroke takes place in a U-movement, so that the opening is possible for short parts The milling stop remains as small as possible. Spindle stroke horizontally fine Adjustable for both tool positions from the operator side. Central lubrication for the spindle units. The 1. Spindle can be selected in right-left rotation. This spindle dips the last 100 mm of each frame end appropriate synchronization tool into the passing wood. Through this This prevents the tool of the subsequent milling spindle from running in the opposite direction working, causing tearouts. Excavation of the first 7 transport rollers using Footswitch. This shortens the lead time. An additional The support rail also allows large-format frames to be milled around. Continuous, chainless rubber roller feed with extreme short roller spacing. Height adjustment of the feed bar electrically readable. Electrical version according to VDE. Machine including operating tools, but without processing tools tools. Technical data: Working width min. 40 mm Working height min. 30 mm, max. 100 mm 1. Profiling spindle (synchronous and counter-rotation) ----- -- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm with synchronous automatic immersion 2. Profiling spindle ----- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 3. Profiling spindle ----- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 4. Profile spindle - fitting unit on the right ----- For milling the fitting groove in the milling cycle or for grooving in the longitudinal profile. Pneumatic horizontal movement with Selector switch in the control panel. Motor 2.2 KW Speed 6,000 rpm Spindle diameter 40 mm Clamping height 125 mm, 2 tools Tool flight circle min. 140 mm, max. 180 mm Motor power feed 1.1 kW Feed speed 6 - 12 m/min. ...

Condition: used, Year of construction: 2018, Number of motors 1 Stück 0 2500 mm Control nein Hecht ES 350 single-sided glazing bead saw ----- Pneumatic pivoting against fixed stops. 45º/ 90º/ 135º with pneumatic sawblade feed pneumatic tilting via manual tilt stop with machine base, pneumatic clamping HM sawblade 350 x 3.0/2.2/30 Z 100 Iisdsvpr N Rspfx Agzok Saw stand dimensions: length 700 mm, depth 1,600 mm, height 1,500 mm 1.5 m touch stop 1.5 m support with support 3 m touch stop Support extension from 1.5 m to 3 m with support Table inserts grooved for rebated glazing beads HECHT ASB manual length stop with digital display, 2,500 mm With dust extraction unit (Technical specifications according to the manufacturer - no guarantee!)

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) Iiedpfx Agev D Rg Djzek with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction nozzle: 1930 mm Working...

Condition: used, Tenoning spindle 1 St. Number of milling agregates 5 St. Spindle diameter 50 mm Control Weinig, PC-Nexus # 2774 Weinig Unicontrol 6 with NC spindles Machine will be cleaned and completely checked before delivery ----- Technical data summary (please enquire about any additional accessories included) Item 1: Cross-cut saw ----- > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3 kW > Radial adjustment path pneumatically controlled to 8 positions, e.g. for edge rounding from above > Laser aiming light for detecting the saw section Item 2: Rounding unit horizontal below ----- > Position: horizontal below > Motor power: 1.5 kW > Spindle diameter: 20 mm > Clamping length 25 mm > Spindle speed: 9,000 rpm > Max. tool flight circle: 130 mm > Axial adjustment path mechanically coupled with Crosscut saw > Adjustment path radial pneumatically controlled on/off Length stop NC controlled ----- > Length 3500 mm > Electronic length stop Item 3: Tenon and slot spindle ----- > Number of tools: variable, stepless adjustment, NC > Tool clamping length: 320 mm > Vertical spindle stroke: variable 254 mm, stepless adjustment, NC-controlled > Spindle speed: 3500 rpm > Tool flight circle max. 320 mm > Spindle diameter: 50 mm > Tool diameter max.: 320 mm > Motor power: 11 kW Item 4: 1. Profiling spindle (same and opposite rotation) ----- > Position: vertical right > Number of tools: 1 pc. Iedevu Hghepfx Agzsik > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 7.5 kW Item 5: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, stepless adjustment, NC > Tool clamping length: 320 mm > Vertical spindle stroke: variable 254 mm, stepless adjustment, NC-controlled > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 11 kW 2 feed rollers axially pneumatic opposite the spindle controlled, 2 positions Rung guide consisting of: Guide ruler in the stop (area of ??the synchronous spindle), Rung support bar from above in the area of ??the profile milling unit vertically on the right and profiling spindle. Pos. 6: Profile milling unit horizontal top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed ??9,000 rpm > Tool flight circle max. 130 mm > Axial adjustment range 30 mm, 8 positions > Radial adjustment range 125 mm, 8 positions Pos. 7: 3rd profiling spindle (fitting spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment range 115 mm, 8 positions > Radial adjustment range 110 mm, 8-way turret > Spindle speed: 5850 rpm > Spindle diameter: 40 mm > Tool flight circle max.: 210 mm > Motor power: 3.0 kW Item 8: Profile milling unit/grooving unit from below ----- > Motor power: 3.0 kW > Tool clamping length: 125 mm > Axial adjustment range 100 mm, 8 positions > Radial adjustment range 1...

Condition: used, Number of boring motors 1 St. boring of corner bearing 1=yes, 0=no 1 ja_yes boring of olive 1=yes, 0=no 1 ja_yes 1 HESS fitting drilling station for corner bearings and olives This Hess drilling station for tradesmen offers a lot of drilling technology for little money. A complete station for drilling corner bearings and olives with all the important features, such as 2 clamping cylinders, drilling depth sensing, effective suction, stop systems for corner bearing and olive drilling, drilling head with interchangeable chuck, adjustable drilling feed speed, automatic program sequence. This means technology for perfect work: just one machine with just one drilling unit and just one drilling head for 2 work steps. The system: - Base frame as a support wall for frames and sashes up to 100 mm - Drilling unit positioned in the middle, height manually adjustable via threaded spindle - Drill hole position and depth set to the specified fitting type, can be adjusted via a stop system when changing types - Drilling feed speed can be variably regulated via throttle valve - Direct extraction - Electro-pneumatic control system with automatic Program sequence for - Fixing workpieces - Drill motor on - Drilling unit forwards - Drilling - Drilling unit backwards - Drill motor off - Releasing workpiece fixation - Fixed stop systems Basic equipment / Technical data: Sturdy base frame as a support wall, precise support made of abrasion-resistant and dimensionally stable plastic, for frames and sashes up to 100 mm thick, Corner bearing and olive drilling in one machine and in one drilling unit, simple and convenient, vertical work, easy handling, no templates, minimal time required for the safe workpiece positioning, guarantee for exact and precise drilling, 2 clamping cylinders for immovable fixation of sash or frame, adjustable to different wood thicknesses, side stop in the rebate for the corner bearings, ergonomically arranged stop system for olive drilling with 14 swiveling stops and additional color markings, fixed stop system for drill hole height determination when changing from corner bearing to olive, Iedpfx Agevu Hgzezjik automatic drilling depth sensing for corner bearing and olive, drill unit with quick-change chuck for the various tools for corner bearing and olive, tool change in "no time", automatic program sequence, clean work thanks to effective suction, small space requirement and mobile thanks to steering/brake rollers. Electrical equipment in accordance with VDE. Electrical connection: 0.55 KW, 400 V, 50 Hz. Pneumatic connection: R 3/8", 4 - 8 bar Extraction connection nozzle: 1 x 100 mm diameter Extraction speed: 25 m/sec. Space required: Width: 2600 mm Height: 1250 mm Depth: 800 mm Support height: 300 mm Paint finish: RAL 7030 stone grey with RAL 1018 zinc yellow 1 drill set with 1 drill 25 mm and 2 drills 10 mm plus 1 drill 34 mm diameter (technical data according to manufacturer - no guarantee!)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Iiedpfx Aet Tqy Eegzok Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...