Leadscrew/feed shaft lathe / DROOP & REIN

Droop+Rein SZ 100

Condition: used, Year of construction: 2000, turning diameter over bed 440 mm turning diameter over slide rest 270 mm turning length 1.500 mm center height over bed 220 mm digital readout FAGOR 3 Achsen turning diameter in the gap 620 mm centre distance 1.500 mm bed width 280 mm spindle bore Ø 52 mm turning speed range 30 - 2.360 U/min 3-jaw-chuck diameter 250 mm quick change toolholder KLOPFER Typ GX2B drive capacity - spindle motor 6,3 kW taper in tailstock-quill MK 4 dia. of quill 60 mm quill stroke 200 mm voltage 380 V Lhodpfx Aoykb Hfjl Teh total power requirement 6,5 kW weight of the machine ca. 1,5 t dimensions of the machine ca. 2,90 x 1,10 x 1,75 m - Serial-No.: D8KK0633 - 3-axis digital readout FAGOR - Quick-change steel holder - rapid clamping boring chuck RÖHM 1-13 mm - Coolant device

Condition: good (used), NHH lathe Turning diameter bed: 260 mm Turning diameter support: 160 mm Spindle bore: 26 mm Turning lenght: 600 mm Heidenhain digital measurement Diameter faceplate: 155 mm Lsdjmw Ukcopfx Al Tohh Speed: 2000 RPM Dimensions: 150x85x155 cm LxWxH

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min Ljdpfxexacirs Al Tjhh motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - KLOPFER three-jaw chuck Ø 140 mm - collet holder with lots of collets - foldable lathe chuck guard - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall - emergency stop button, bottom right - machine swing feet - original operating instructions

Condition: good (used), Year of construction: 1991, functionality: fully functional, Weiler Praktikant 160 B, year of manufacture 1991, 3-axis digital readout, center height 160 mm, center distance 650 mm, spindle speed up to 2,500 rpm, tailstock, collet set, chuck, holder, 1 set of bed guides. Ledpfx Ajyn Auxel Tjhh

Condition: used, Year of construction: 1957, turning diameter over bed 800 mm Lhjdpoxwp Ehofx Al Teh turning diameter over slide rest 540 mm turning length 4000 mm centre height 400 mm centre distance 4000 mm spindle turning speed range 9 - 1140 U/min spindle passage 96 mm weight of the machine ca. 8,5 t dimensions of machine L x W x H 7,0 x 1,70 x 1,70 m - with gap with insert - Accessories: 3-jaw chuck FORKARDT 400 mmø, 4-jaw chuck 500 mmø, faceplate 800 mmø, DRO on X-and Z-axis ACU-RITE, MULTIFIX-head with various inserts, 2 solid steadies, 1 running steady, running center, coolant

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 Ljdpfsxmakyex Al Tjhh quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - HEIDENHAIN 3-axis digital display “VRZ 773” - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - Emergency stop button - Operating instructions

Condition: used, Year of construction: 1973, turning diameter over bed 490 mm turning diameter over slide rest 280 mm turning length 2000 mm Lhedetqqvvopfx Al Teh centre height 245 mm centre distance 2000 mm spindle bore 62 mm total power requirement 7,5 kW weight of the machine ca. 3,5 t dimensions of machine L x W x H 3,78 x 1,17 x 1,42 m Accessories: 3-jaw chuck 240 mmø, face plate 400 mmø, MULTIFIX-tool post, solid steady, coolant

Condition: like new (used), functionality: fully functional, Weiler Commodor Lead and Feed Screw Lathe with 3-axis K&C Digital Readout, newly overhauled, with acceptance protocol for tolerances equivalent to new machines. Technical Data: >> Machine Serial No.: 2268-87 >> Centre Height: 180 mm >> Distance Between Centres: 1000 mm >> Spindle Speeds: from 13 to 2000 rpm >> Spindle Bore: 56 mm >> Short Taper Spindle Nose DIN 55029 Camlock >> Tailstock Morse Taper 4 >> Feed Rates: 0.026 to 0.888 mm/rev >> Thread Cutting Capability: Metric, Inch, Module, and Diametral Pitch >> Metric Thread Pitches: 0.35 to 12 mm >> Weight: approx. 1500 kg >> Spindle Brake can be engaged >> Drive Power: 2.0/4.0 kW >> Dimensions (LxHxD): 2.2 m x 1.5 m x 1 m Ljdpfx Aljymznhs Tjhh Equipment and Accessories: >> 3-axis K&C Digital Readout, new, with 12-month manufacturer’s warranty and manual >> NEW 3-jaw chuck, 200 mm, with 2 sets of jaws >> Multifix size B with 3 new tool holders >> Bed stop >> Machine feet >> Coolant system >> LED machine light Safety Features: >> Electronic spindle guard >> Spindle brake >> 2 emergency stops Optional: Lead and feed screw covers available on request About the machine: For sale is a Weiler Commodor lead and feed screw lathe in geometrically overhauled condition. The ways have been reground or hand-scraped. Acceptance is according to inspection protocol. Finished in 2K gloss white paint. Multifix toolpost and chuck are new. For safety: The machine is equipped with a brake motor, electronic spindle guard, and two emergency stops, making it an as-new lathe. Even at high spindle speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is extremely user-friendly and is capable of producing ground-like surface finishes. Take advantage of the opportunity to inspect the machine under power on-site and see its condition for yourself.

Condition: used, Year of construction: 2000, used CONDOR AC, partially overhauled Centre height: 165 mm Between centres: 750 mm Spindle bore: 40 mm Spindle speeds: 22–2,800 rpm, infinitely variable - Quick-change tool post size B - WEILER DZ-V digital readout Lhedpfxsx E Um Ns Al Tjh - Hollow spindle stop - Fixed steady rest - 7 Multifix tool holders - Flat splash guard - Electrically interlocked chuck guard - Change gears and various soft jaws The machine is partially overhauled: - Bed slide: guideways re-coated and hand-scraped, gibs and lower guide strips adjusted - Cross slide measured and aligned on bed slide; cross slide dovetail guide newly scraped, gibs adjusted and scraped - Top slide newly scraped and gib matched - All measuring scales overhauled and cables replaced The machine is located in our showroom at 71334 Waiblingen-Beinstein and is immediately available. For details on equipment, please contact us.

Condition: used, functionality: fully functional, Manufacturer: Haaf (formerly Gema) Type: LZ 185 Swing diameter over bed: 365 mm, over cross slide: 225 mm Turning length: 750 mm Centre height: 185 mm Spindle bore: 40 mm Spindle flange: KK5 (DIN 55022) Spindle taper: MK5 Speed range: 20 – 1,600 rpm Heidenhain VRZ 773 B digital readout on 2 axes (scales on the cross and longitudinal slides) Dimensions: 1,900 x 900 x 1,700 mm Additional equipment: - Spindle brake with foot pedal - Adjustable stop on the cross slide (disengagement of feed) - Splash guard Accessories: - Operating manual - Multifix B holder with 2 inserts - Coolant pump integrated in machine base (no coolant hose connected) - Röhm 3-jaw chuck 200 mm with hard and soft jaws Weight: approx. 950 kg Condition: Used Lodpfxjw Svtce Al Tehh The machine runs smoothly and can be inspected under power. All information is provided without guarantee; errors excepted; all dimensions are approximate. Offer is subject to change without notice. The machine can be inspected by appointment. Changes and errors in technical data, information, and prices as well as prior sale are reserved! All prices are net plus VAT. Payment in advance, including any shipping costs, to be made within 14 days of contract conclusion. If the full purchase price is not paid within this period, the seller reserves the right to cancel the sales contract. Sale is only to commercial buyers within the meaning of § 14 BGB. The machine is sold with exclusion of warranty for material defects. This exclusion does not apply to claims for damages arising from liability for material defects which are based on gross negligence or wilful misconduct by the seller or his agents, or in the event of injury to life, limb or health. Any existing third-party warranty claims are assigned to the buyer. Please understand that I cannot assume any liability for compliance with any safety regulations that may be applicable to you or generally required concerning the machine and its components. Ensuring such compliance is the responsibility of the end user. All contracts concluded are subject exclusively to the law of the Federal Republic of Germany to the exclusion of the UN Sales Convention. Place of jurisdiction agreed as Mannheim.