Gear Hobbing Machine - Vertical

GLEASON PFAUTER GP 130

Condition: excellent (used), Year of construction: 2002, max. wheel diameter 130 / 80 mm Hfedpfjxlug Hsx Abroc gear width 180 mm max. module 4 min. module 0,5 spindle turning speed - stepless 300 - 3000 U/min control Siemens 840 D x-travel 200 mm y-travel 170 mm z-travel 250 mm milling head -swivable +/- 45 ° table diameter 168 mm table hole 65 mm clamping length max. 245 mm table turning speeds 0 - 1000 U/min total power requirement 51 kW weight of the machine ca. 9,2 t dimensions of the machine ca. 4,5 x 4,0 x 3,2 m

Condition: refurbished (used), Year of construction: 2025, operating hours: 50 h, machine/vehicle number: 3018-04, Country of manufacture: Switzerland Voltage: 380/50/3 Net weight: 3100 kg Overall dimensions: 230x155x170 cm Installed power: 13 kVA Customs tariff position: 8460.2920 TECHNICAL SPECIFICATIONS Hfjdpfsw T Sd Tjx Abrjc MAIN DIMENSIONS Distance between centers: 650 mm Grinding capacity SpW+bs: -80 Stroke: 700 LONGITUDINAL SLIDE Max stroke: SpW+50 mm Minimum automatic feed: 1.5 mm Speed: 50-5500 mm/min Reversal delay: 0-6 sec Maximum table swivel: 12°/10°/8.5°/6° Pneumatic relief for table and workhead CROSS SLIDE Max stroke: 300 mm Rapid traverse: 60 mm Plunge grinding depth in diameter: 3.4 mm Feed 1: 0.012-6 mm/min Feed 2: 0.012-1.2 mm/min Feed per pulse: 0.001-0.05 mm GRINDING WHEEL HEADSTOCK Left-side wheel, external grinding: 400x80x127 mm Drive power: 5.5 kW Peripheral speed: 35 m/s RPM: 1670/2110 min-1 Internal grinding device for belt-driven spindles, including drive unit: 1.5 kW WORKHEAD Swivel range: 0-90° Continuously variable RPM: 30-1000 min-1 Internal taper: Morse 5 Collets: W-25 Drive power: 0.55 kW Maximum workpiece weight between centers: 130 kg Grinding load between centers: 100 Nm TAILSTOCK Internal taper: Morse 3 Quill stroke: 35 mm Fine adjustment for cylindricity correction: ± 40 μm TECHNICAL CHARACTERISTICS: GUARANTEED WORKING ACCURACY Straightness of the generator over 630 mm: 0.003 mm Roundness during chuck grinding: 0.0003 mm CONNECTION VALUES Maximum absorbed power: 13 kVA Maximum permitted voltage fluctuation: -15%/+10% Maximum permitted frequency variation: ± 3% Required compressed air pressure: 5 bar Unless otherwise stated or in case of error or omission, these technical details are provided without engagement.

Condition: used, Year of construction: 2001, Control SIEMENS Hedpfoudc S Tsx Abrefc table surface area 160 mm weight of the machine ca. 10 t

Condition: used, Year of construction: 2004, Technical details: Hodpfx Abevi Ninersfc max. wheel diameter: 130 mm gear width: 25 mm module max. : 3 module min. : 0,5 control: Siemens 840D work-spindle diameter: 85 mm strokes - infinitely variable: 500 - 2500 Hub/min stroke: 30 mm total power requirement: 48 kVA weight of the machine ca.: 11,5 t space requirements approx. LxWxH: 4,7 x 3,0 x 3,3 m Equipment: -Counterholder with tip -chip conveyor -hydraulically operated counterholder arm and linear guides i.D. *

Condition: good (used), Year of construction: 2001, Manufacturer: KASTO Type: KASTOtec A4 Year of construction: 2001 Specifications: Metric Metric US Standard Sawing capacity round 90 430 Sawing capacity flat 90 430 x 430 mm Feed range 0 - 600 mm Multi-feed range 0 - 9999 mm Min, saw length 35 mm Max. Sawing speed 12 - 120 Saw blade dimensions Hfodpfxou R R Avo Abrjc 6830 x 41 x 1.3 mm Saw power 7.5 kW Dimensions (estimate) length 4800 mm width 2200 mm Height 2200 mm weight 5200 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: used, Year of construction: 2002, functionality: fully functional, wheel diameter: 130 mm, workpiece height (max.): 170 mm, TECHNICAL DETAILS Control: Sinumerik 840D Tip diameter: 80 mm Toothed length: 170 mm Overall length of hob cutter: 245 mm Collet diameter: 32 mm Tool speed: 300 - 3000 rpm Hjdpfx Abev I Tmusrsfc Gear diameter: max. 130 mm Gear width: 170 mm Module: 0.5 - 3 Slide travel radial / tangential / axial: 200 / 170 / 250 mm Milling head swivel angle: ± 45° Workpiece table: Ø 168.14 mm Bore: 65.532 mm Table speed: 0 - 1000 rpm Table bore: 65.532 mm Feed X/Z: 1 - 6000 mm/min Rapid traverse X, Z / Y: 6 / 5 m/min MACHINE DETAILS Total power requirement: 48 kVA Operating voltage: 3 x 400 V, 50 Hz Machine weight: approx. 9 t Space requirement: approx. 7.64 x 3.14 x 3.25 m

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, feed length X-axis: 230 mm, feed length Y-axis: 25 mm, feed length Z-axis: 150 mm, workpiece diameter (max.): 300 mm, TECHNICAL DETAILS Control: Siemens 840 D Nominal module in steel with approx. 600 N/mm² tensile strength: 4 Largest tooth width: 25 mm Largest nominal diameter: 130 mm Largest helix angle when using 125 mm diameter cutting wheels: ± 45° Workpiece with internal gearing Nominal module in steel with approx. 600 N/mm² tensile strength: 4 mm Largest tooth width: 25 mm Largest swing diameter: 300 mm Largest inner diameter: 130 mm Tool Largest permissible cutting wheel diameter: 175 mm Cutting wheel holder – diameter: 1.5 inches Cutting wheel holder – taper in the shaping spindle: PKP 45 hollow steep taper – Bauer Travel paths Radial (X-axis): 230 mm Manual transverse column adjustment (Y-axis): ± 25 mm Adjustment range of the axial slide (Z-axis): 150 mm Workpiece table Outer diameter: 168.14 mm Bore: 65.532 mm Spindle spindle Largest stroke length (V-axis): 30 mm Spindle axis adjustment range: ± 0.25° MACHINE DETAILS Length: 6,435 mm Hfsdpfowc Tg Njx Abroc Width: 4,560 mm Height: 4,400 mm Weight: approx. 11,000 kg

Condition: good (used), Year of construction: 1963, Vertical lathe JUNGENTHAL Type: DK 1400 built in 1963 with 1 axis digital readout. turning diameter max : 1400 mm face plate : 1250 mm Automatic turret head spindle speed : 3,5-180 rpm feeds : 0,063 - 3,15 mm/rev Hfodpfxsvi Hrye Abroc rapid traverse : 1800 mm/min Further data see data sheet Machine documentation available . Dimensions : Length 4 m Width 2,4 m Height 3 m Weight 16t Good general condition .

Condition: used, TECHNICAL DETAILS - Number of axes : 7 - Number of spindles : 2 MAIN SPINDLE - Spindle power : 15 [kW] - Spindle speeds : 5500 [rpm] - Max. bar diameter : 42 [mm] - C axis indexing precision : 0.001 [°] COUNTER-SPINDLE Hjdpfx Absuhamporjfc - Spindle power : 15 [kW] - Spindle speeds : 5500 [rpm] - Max. bar diameter : 42 [mm] - C axis indexing precision : 0.001 [°] - Travel : 330 [mm] TURNING-MILLING SPINDLE - X/Z stroke : 410/400 [mm] - Y stroke : 200 [mm] - B Axis stroke : -25/+115 [°] - B axis indexing precision : 0.001 [°] - Tool type : HSK40 - Spindle speeds : 30000 [rpm] - Spindle power : 8 [kW] TOOL CHANGER - Auto. Tool Changer type : Parapluie - Tool magazine capacity : 60 - Tool exchange time : 1.2 [sec] - Number of positions : 60 POWER SUPPLY - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine floor space : 3300 x 2900 [mm] - Machine height : 2100 [mm] - Machine weight : 5000 [kg] MACHINE HOURS - Number of working hours : 11659 [h] EQUIPMENT - CNC : Fanuc 31i model A5 - Linear scales - Coolant tank * with high-pressure pump : 70 [bars] * Coolant through spindle - Oil mist extractor : ELBARON RON/A 100 DV - Spindle cooling unit - Workpiece probe : Renishaw OMP40-2 - Parts catcher - 1 NAKANISHI HTS1501S spindle : 150.000 [rpm] - Fire extinguisher * * NB : working order not guaranteed. To have it checked by a qualified organization of the buyer. - Bar puller

Condition: reconditioned (used), Year of construction: 1992, functionality: fully functional, center height: 150 mm, grinding length: 620 mm, center width: 680 mm, grinding wheel diameter: 350 mm, total width: 500 mm, Condition of the machine: The machine is currently in a used, non-overhauled condition. The following work carried out on the machine: - Complete disassembly of the entire machine except for the guides - Replacement of all sealing and wear parts of the entire machine - Replacement of the infeed spindle of the X-axis - Replacement of the main bearing of the workpiece spindle - Replacement of grinding spindle - All machine assemblies are restored to as-new condition Geometry: - Scraping of the X-axis guide - Scraping the Z-axis guide - Grinding the X-axis table - Grinding the Z-axis table Hjdpjrz Nflsfx Abrjfc - Grinding the upper tables - Grinding of the assembly housing (workpiece headstock, grinding headstock and tailstock) - Creation of measurement report for TSCHUDIN cylindrical grinding machine Painting: The main assemblies are repainted, the rest of the machine retains the original paintwork Electronics: The complete electronics of the machine are checked, tested and defective switches and cables are replaced