Johnford VMC-1600S

Johnford VMC-1600S

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Godpeyx Uy Asfx Al Uebu Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Condition: excellent (used), machine/vehicle number: 3.278-870805-1, Part No.: 42.35.53 Technical data and description: see pictures Gedpfx Aeh Eii Tsl Ujbu

Condition: excellent (used), DOOSAN VC 630/5AX YEAR 2015 CNC HEIDENHAIN 530 AXIS TRAVEL: -X: 650 mm -Y: 765 mm -Z: 520 mm -A: 150 (+30 -120º) – (0.001º) -C: 360º (0.001º) TABLE: -5 Continuous axes -⌀ 630 mm -Distance from spindle to table: 210-730 mm -Max. permissible weight: 500 kg RAPID TRAVERSE: Gbsdezc Hm Uspfx Al Uou -X: 40 m/min -Y: 40 m/min -Z: 36 m/min -A: 20º/min -C: 30º/min BALL SCREWS: ⌀ 45 X 16 (X, Y), ⌀ 45 X 12 (Z) mm ELECTRIC SPINDLE HEAD ISO 40 DIN69871 (*Brand new) -Motor power (continuous - 30 min): 24/32 Kw -RPM: 20,000 INCLUDED OPTIONS: -Optical scales on all axes -120-tool changer -Automatic pallet changer with 5 pallets -Renishaw measuring probe -Laser pre-measuring device -Chip extractor CONDITION: Machine in excellent condition. Headstock is completely new. Available for inspection in operation.

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: 626963, Heidelberg - SM 74-2 H Number of copies produced 74.077.397 Year of Production -2003 Max-Sheet Size 530 × 740 mm (20.87 × 29.13 in) -- 2/0—1/1 Gjdpjz Nz S Aefx Al Usbu Max.printing Speed 13000 /h CP 2000 Center, AutoPlate system, Dampening rollers Alcolor Automatic Wash rollers and Cylinder Ink Fountain-Ink zone motor Electric equipment- 50Hz 380 V Pull Lay control-Electronic Powder spray-Alphathronic 200 Circulation and cooling ---Dampening Baldwin Device Available immediately

Condition: used, Three Dimension Coordinate Measuring Machine MITUTOYO CRYSTA-Apex S574 Gbjdey Ufkkjpfx Al Uju

Condition: excellent (used), Year of construction: 2020, travel distance X-axis: 8,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 2,500 mm, rapid traverse X-axis: 35,000 m/min, rapid traverse Y-axis: 40,000 m/min, rapid traverse Z-axis: 40,000 m/min, total width: 5,800 mm, total height: 4,500 mm, total length: 13,500 mm, table length: 10,000 mm, table width: 1,250 mm, Travelling Column High performance, precision and machining power Linear guiding of RAM combined with Hydrostatic Guiding HDS ACD2 Milling head with 5000 Rpm and 1400 Nm torq Aitek ATC chain 60 position with L=400 and 250 diameter x 35 Kg Filtration with IKZ 15 Bar Chip conveyor BLUM 3D Measuring probe Wide bed linear guided in X-Travel W=930 mm Rotary table driver prepared in E-Cabinet X-Axis: 8000mm Y-Axis: 1300mm Z-Axis: 2500mm Table Length: 10000mm Table Width: 1250mm Power on spindle: 40kW Godpfeyr Dmdox Al Uebu Spindle speeds: 5000Rpm Spindle Taper: 40ISO/Bt/Mk Feed rate X-Axis: 35000mm/min. Feed rate Y-Axis: 40000mm/min. Feed rate Z-Axis: 40000mm/min. Millinghead auto-index:0.001 x 0.001 Gr° Working hours: 3800H Length: 13500mm Width: 5800mm Height: 4500mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2003, table length 900 mm table width 900 mm Gjdpfex Szp Dsx Al Usbu x-travel 457 mm y-travel 508 mm z-travel 406 mm control Brown & Sharpe weight of the machine ca. 600 kg dimensions of the machine ca. 1300 x 1000 x 2400 mm

Condition: good (used), Year of construction: 2011, Ref. -No.: 10598 Manufacturer: HELLER Type: MC 2000 Year of construction: 2011 Type of control: CNC-Steuerung Control: Siemens 840 D sl Storage location: Halberstadt Country of origin: Hermany Machine-No.: 50XXXX X-Travel: 800 mm Y-Travel: 800 mm Z-Travel: 1000 mm Work spindle torque (25% ED): 242 Nm Tool Taper: SK 40 Numbers Of Tools In Magazin: 54 Tool Piece Magazine With: 80 Pcs./pcs. Turning Speeds: 10000 RPM Drive Capacity - Spindle Motor: 17 kW High-Pressure Pump: 50 bar Speed range - main spindle: 10000 RPM Numbers Of Pallets: 2 Size Of Pallet: 630 x 500 mm Weight Of The Machine Ca.: 13000 t spindle running time: 7000 H Gsdpfx Aex Hn D Rsl Uebu Operating hours: 14000 H Preparation area: 4 x 90° hydraulic pressure: 200 bar Further information: - The machine has been measured - The geometry is in excellent condition - The spindle runs a little rough - Clamping towers and cutting tool holders are also included - 2 additional clamping towers - 2 replacement pallets - 2-axis servo tool changer - Scraper conveyor for dry machining - Cold light in the work area - Central cooling unit for motor spindle and control cabinet - Control unit at the workpiece setup station - NC-controlled rotary table - Clamping hydraulics The machine can be viewed under power by appointment.

Year of construction: 2015, condition: ready for operation (used), A CNC milling machine Spinner is available. Travel X/Y/Z: 760mm/460mm/460mm, table dimensions X/Y: 900mm/410mm, max workpiece weight: 350kg, tool stations: 24, max tool weight: 8kg, max tool length: 200mm, speed: 12000rpm, max tool diameter: 80mm, tool holder: SK40. Machine dimensions X/Y/Z: approx. 2600mm/1600mm/2850mm, weight: approx. 4000kg. Including automation and robot M10. Documentation available. An on site inspection is possible. Gjdpfxoxwn I Uo Al Uobu

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, travel distance X-axis: 730 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 560 mm, spindle speed (max.): 12,000 rpm, For sale is a very well-maintained 5-axis simultaneous machining center, DECKEL MAHO (DMG MORI) type DMU 60 monoBLOCK, manufactured in 2009. The machine is characterized by very low spindle hours and extensive equipment. Highlights & General Information: Manufacturer / Model: DECKEL MAHO (DMG MORI) DMU 60 monoBLOCK Year of manufacture: 2009 Control system: HEIDENHAIN iTNC 530 Operating hours: approx. 30,000 h Spindle hours / program runtime: approx. 8,000 h Technical Data: Travel ranges: X = 730 mm Y = 560 mm Z = 560 mm 4th axis (B-axis / swivel head): +30° to -120° (NC swivel milling head with hydraulic clamping) 5th axis (C-axis / rotary table): 360° (endlessly rotating NC rotary table, resolution 0.001°) Main spindle: Max. 12,000 rpm Tool holder: SK 40 Tool changer: 60-position chain magazine Equipment & Accessories: Internal coolant supply (IKZ) including paper band filter system Chip conveyor Gedpfx Aszz Snyjl Uobu Workpiece measuring probe: DMG TS 649 Complete documentation and machine keys available Upon request, for an additional charge, loading and transport (throughout Europe) can be arranged. All prices plus VAT. Inspection possible by appointment. Contact us, our team will be happy to assist you further. Trade-in or exchange possible! Machine purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Do you need a high-quality but affordable metalworking machine for your production? Or do you want to sell yours?