Gear Shaping Machine

LORENZ S7 / 1000

Condition: excellent (used), max. wheel diameter 1000 mm gear width 160 mm Fedpjydfn Hefx Akvogb max. module 7 min. module 0,5 distance table - lower edge of ram 230 mm no. of strokes 31 - 175 Hub/min tool taper MK 4 total power requirement 6 kW weight of the machine ca. 5,2 t change gears, tool-holders, clamping plates, manuals,...

Condition: ready for operation (used), The machine is in very good condition and can be tested on site. Technical Data – Grinding Machine Machining area (mm) Height x Length x Depth: 80 x 110 x 55 Fjdpswvgidofx Akvegb Motor power (kW): 0.5 Speed (min-1): 5000 Feed rate (hod/min): 150 Table load (kg): 20 Control: BOSCH Accuracy: 0.005 mm, reading via CNC, template grinding 1:10, 1:20, or 1:50, suitable for rough grinding. If you have further questions, I am at your disposal.

Condition: good (used), Year of construction: 1994, functionality: fully functional, feed length X-axis: 1,050 mm, feed length Y-axis: 360 mm, feed length Z-axis: 500 mm, travel distance X-axis: 1,050 mm, travel distance Y-axis: 360 mm, travel distance Z-axis: 500 mm, overall weight: 3,000 kg, Equipment: documentation/manual, Tiger FO 135 universal milling machine Description of the machine The machine was purchased new in 1994 and has only been in operation for a few hours. The milling machine is fully functional. The axis movements are smooth and the guides are in good condition. good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a digital readout for the 3 axes, which makes it possible to work with cutter compensation and recurring measurement machining. Operating instructions are included with both the machine and the digital indicator. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic traverse path: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds ➢ Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed power: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ Direct current motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast feed ➢ Lengthwise and crosswise 3,000 mm/min Vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low-voltage electrical controls on the pushbutton panel of the side arm - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Machine dimensions (for transportation) ➢ Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accessories - Counter supports for cutting shaft - Cutting shaft ø32 mm Tiger FO 135 universal milling machine Description The machine was purchased new in 1994 and has only had a few hours of operation. Fedpfxorqwbij Akvogb The milling machine is fully functional. Axis movements are smooth and the guides are in good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a DRO for the 3 axes, which offers the possibility of working with milling compensation and recurring measurement processing. Both the machine and the DRO come with operating instructions. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic travel: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed services: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ DC motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast forward ➢ Longitudinal and transverse 3,000 mm/min ➢ vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low voltage electrical controls on side arm push button panel - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Dimensions of the machine (for transport) Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accesories - Counter supports for cutting shaft - Cutting shaft ø32 mm

Condition: like new (used), Year of construction: 2018, operating hours: 23,501 h, functionality: fully functional, turning length: 705 mm, turning diameter: 366 mm, spindle motor power: 18 W, spindle speed (min.): 4,000 rpm, spindle speed (max.): 10,000 rpm, travel distance X-axis: 260 mm, travel distance Y-axis: 50 mm, travel distance Z-axis: 795 mm, rotational speed (max.): 10,000 rpm, total height: 2,395 mm, total length: 5,330 mm, total width: 4,100 mm, overall weight: 8,360 kg, CNC controller: Mitsubishi M730UM (CELOS - ERGOline Touch) Capacity X-axis travel mm: 260 Y-axis travel mm: ±50 Z-axis travel mm: 795 Turning length mm: 705 Max. turning diameter mm: ø: 366 Swing over bed mm: ø: 920 Swing over cross-slide mm: 740 Bar work capacity mm: 80 Tool magazine Magazine places: 20 Tool holder: BMT40 Fjdpfoywtwwox Akvogb Upper turret Number of tool slots St .: 20 Speed driven tools RPM: 10.000 Drive power driven tools kW: 5.5/4.9/4.2 (3 min/5 min/cont) Rapid Feed Rate: 30 Main spindle Speed spindle rpm: 4.000 Drive power spindle kW: 18.5/18.5/15 (25%ED/50%ED/cont) Maximun torque Nm: 49 Counter spindle Speed spindle rpm: 5.000 Drive power spindle kW: 11/7.5 (25%ED/cont) Maximun torque Nm: 22 Counter spindle travel mm: 734 Coolant system Tank capacity liter: 366 Equipment Electronic Handwheel Chip conveyor Signal lamp High pressure pump Measuring probe Paper band filter Working time hours Under power: 23.501 Cutting Time: 7.494 Potencial nominal kVA: 48 Basic machine dimensions / weight Length mm: 5.330 Width mm: 4.100 Height mm: 2.395 Weight kg: 8.360

Condition: used, Year of construction: 2007, machine/vehicle number: 134418, measuring range X-axis: 1,200 mm, measuring range Y-axis: 1,800 mm, measuring range Z-axis: 1,000 mm, Equipment: type plate available, Technical Data Fsdpfx Aoxnruaokvjgb Manufacturer: Zeiss Type: Accura 12/18/10 S/N: 13418 Year of manufacture: 2007 Measuring Plate Hard stone measuring plate Width: 2,400 mm Depth: 1,700 mm Height: 400 mm Measuring Range X-axis: 1,200 mm Y-axis: 1,800 mm Z-axis: 1,000 mm Accessories Control panel PC unit 2 x 27" monitors, brand BenQ Keyboard Mouse Accessories Stored in a two-door metal cabinet Price: on request! Note: Our offer is aimed exclusively at professional customers. (Subject to change and error in technical data, details and prices as well as prior sale!)

Condition: used, Year of construction: 1996, functionality: fully functional, travel distance X-axis: 10,000 mm, travel distance Y-axis: 2,600 mm, travel distance Z-axis: 700 mm, Manufacturer: PAMA Model:SPEEDRAM 1 CNC Year1996 Spindle:140mm. Fodpfswzh Apjx Akvegb Tranversal travel:10.000 mm. Vertical travel:2.600 mm. RAM travel:600 mm. Ram Size: 360x320 Spindle travel:700 mm. Spindle taper:ISO 50 Spindle motor power:50 Kw. Spindle speeds: 6 ÷ 2000 Rpm. Cnc:CNC Selca 3045 ATC: 60nos. Total weight:65 Tons. Features and Accessories Complete with: - n. 1 automatic universal milling head - n. 1 Floor plate 6000x2500x300mm -n. 1 Floor plate 4500x2000x300mm - Rotry Table 2000x1600 with long travel 2000mm -Loading capacity on table:15ton - levelling shoes

Condition: good (used), Year of construction: 2007, Parts shown by hand not come. Fedpfx Asrpn Dvskvsgb Technical details shown on picture.

Condition: ready for operation (used), functionality: fully functional, Used gear grinding machine Niles ZSTZ 630i. The machine is fully functional; a video can be provided upon request. Fgodpfx Akjxzfugjvjb

Condition: used, Technical details: spindle diameter: 130 mm drill depth: 1380 mm x-travel: 2500 mm y-travel: 1600 mm z-travel: 380 mm w-axis: 900 Bohrspindelvorschub mm Fgsdpfx Aovr S Ulokvob U-axis: 320 Planschiebervorschub mm control: auf Wunsch tool taper: ISO SK50 revolution per minute: Planschieber:4,5-180 U/min rpm - drive spindle: 4,5-900 U/min feed:: x/y: 5-2000 total power requirement: ca. 40 kW weight of the machine ca.: ca.< 35 + AZusatzeinrichtungen t The machine can be offered in 4 different sales options. Please choose! 1. the machine is in mint mechanical condition. As is/is. 2. the machine as is/is incl. plate field 4000x2000x300mm = stock no. 1101081 3. the machine is newly wired, with new electrical cabinet, digital display, with 4-axis, AC drives from Siemens, axis motors from Siemens (50A/31Nm) with 12 months warranty on all new parts. 4. further additional equipment can be offered as an option. Such as coolant system, chip conveyor, enclosure etc. We should discuss this on the table with your technical staff. i.D. *

Condition: used, Thread rolling machine ORT RP30U 2-roll Fgedpfxst H Ty Us Akvob 30 ton swiveling heads variable speed drive #1331 Under power in our warehouse in Gussago BS. Test run possible M i m u Machine Tools Italy Rolling is a mechanical process without chip removal that can be performed cold or hot, having as a purpose the improvement of the surface finish (therefore the fatigue behavior Power (Ton): 30 Number of rollers: 2