Universal Milling Machine

MAHO MH 400 P

Condition: used, Travel ranges: x 400 mm y 375 mm z 250 mm Table size 200 x 800 mm Spindle speeds 50 - 3150 rpm Tool holder SK 40 Spindle quill travel 50.0 mm Gkjdpjzzxfrjfx Acmob Rapid traverse rate 2.4 / 1.6 m/min Control system: Philips Dimensions L-W-H 1860 x 1790 x 1750 mm

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Gkedsx Tgr Tspfx Acmeb Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1994, 2-sided planing machine, top and bottom Constant table (always the same feed height) Max. planing width: 600 mm Max. planing height: 280 mm Godpfxohuthye Acmskb Planer shafts with strip knives Ready for immediate use.

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm Gsdpfx Aju Rni Hscmskb down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet *

Condition: used, Wig welding machine L-TEC, Inverter TIG 200 DC type WIG welding machine for direct current DC Serial no. 184548, year of manufacture approx. 1994 Power: 200 Amps = 60% duty cycle 155 Amps = 100% duty cycle Adjustment range: stepless Current type: DC (direct current) Mains connection: 400 Volts, 50 Hz, 32 Amps plug - 4 meter hose set with central connection and hand torch - with remote potentiometer (foot switch) - gas pressure regulator - DC only - HF ignition Space requirement L x W x H: 850 x 480 x 740 mm Weight: approx. 150 kg The welding test yields very good results when welding stainless steel with direct current. Gkedpfx Acsdzqb Eemsb Otherwise in good condition.

Condition: new, Year of construction: 2025, x-travel 580 mm Gksdpfx Aotv Riajcmsb y-travel 200 mm z-travel 340 mm speeds 115 - 1750 U/min table surface area 1000 x 240 mm tool taper ISO 40 total power requirement 4,5 kW weight of the machine ca. 820 kg dimensions of the machine ca. 1290 x 1090 x 2170 mm Universal precision drilling and milling machine for horizontal and vertical milling work with digital 3-axis position display DPA 31 Plus Description: - Heavy, solid design made of high-quality, vibration-absorbing gray cast iron - Oil bath gear with ground, hardened gear wheels - Coolant system - Halogen machine lamp with bundled beam - Solid and large cross table, precisely surface-machined with T-slots and adjustable wedge strips - Milling head can be tilted ± 45° - Right/left rotation - X-axis moves either with the handwheel or via the table feed device - Automatic limit switch on the X-axis - Height-adjustable protective screen with microswitch, against flying chips and parts, for the greatest possible protection of the user Scope of delivery: - Gear rim drill chuck 1 - 16 mm / B 18 - Arbor drill chuck ISO40 / B18 - Horizontal milling spindle with counter bearing, disc milling cutter holder Ø22 mm, Ø27 mm - Adapter ISO 40/MK3 - Adapter ISO 40/MK2 - Vertical and horizontal drawbar - T-slot nuts - Drifter - Operating tool

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, Universal Milling Machine Deckel FP4M with 3-Axis Active Digital Readout Heidenhain, Excellent Condition, CE Compliant!!! Technical Data: - Year of manufacture: 1992, Machine no. 2203-8449 - Fixed angle table - Spindle speed: 50 - 2500 rpm - Feed rate: 8 – 630 mm/min - Drive power: 3.7 / 4.4 kW - Spindle brake - Rapid traverse: 1300 mm/min - Travel (X/Y/Z): 500/400/400 mm - Vertical milling head traverseable on column - Vertical and horizontal quill - SK40 taper - Vertical quill extendable by 90 mm - Hydraulic drawbar system - Approx. weight: 1600 kg Equipment and Accessories: - 3-axis active Heidenhain digital readout - Coolant system - Chip tray - Central electric lubrication - Operating manual, spare parts drawings About the Machine: Gkedpfx Aeu Tuk Hocmob For sale is a Deckel FP4M Universal Milling Machine (Active) in very good condition. The machine has minimal backlash, and all slides move smoothly. Even at maximum spindle speeds, the milling machine runs quietly. The machine features hydraulic tool clamping. The FP4M was only occasionally used in a state-run facility for training purposes. On this newer FP4 model, the feed rates are steplessly adjustable in all three axes, and each axis also features a rapid traverse. A major advantage is the active 3-axis digital readout. With the Heidenhain control, you can input measurements that the machine will approach automatically. Oil change has been performed; mechanically and electrically tested. The Heidenhain digital readout makes work easier and even more precise. Take advantage of the opportunity to inspect and test this machine under power on site.

Condition: good (used), Year of construction: 1989, turning diameter over cross slide: 820 mm, spindle bore: 128 mm, turning diameter over bed slide: 515 mm, turning length: 2,000 mm, total length: 6,000 mm, total width: 1,900 mm, total height: 1,800 mm, spindle speed (max.): 1,400 rpm, Centre lathe VDF BOEHRINGER - DUE 800 MACH-ID 9760 Make: VDF BOEHRINGER Type: DUE 800 Year: 1989 3 Axis HeidenHain ND780 dro 3 chuck 400 mm 4 chuck 800 mm Steady rest closed ca 400 mm Steady rest C-Type ca 400 mm Gjdpfx Aozpwwpocmjkb DBC Turning Length: 2000mm Swing over bed Ø: 820mm Swing over cross slide Ø:515mm Spindle bore: 128mm Spindle power: 30kW Bed width: 560mm Speeds / ranges: 1400Rpm Quill Ø: 125mm Workpiece load: 5000 Length: 6000mm Width: 1900mm Height: 1800mm Weight: 6700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), turning length 450 mm turning diameter over bed 245 mm turning diameter over slide rest 135 mm spindle bore 23.0 mm tool adaptor DIN 55021-4 quill: 2 MK quill travel 80.0 mm turning speeds 60 - 3000 U/min bed width 155 mm total power requirement 1.2 / 1.5 kW voltage 380 V weight of the machine ca. 340 kg. range L-W-H 1200 x 650 x 1330 mm from a vocational school (!) particularly suitable for precision turned parts The Primus series is the most compact precision sliding headstock and sliding headstock lathe (LZ) from WEILER. It is used in toolmaking, laboratories and training workshops as an absolute machine for precise work in the tightest of spaces. The machine is built for extremely tight tolerances. The hardened and ground machine bed ensures maximum for maximum vibration damping and durability. Features: - Robust lead/traction spindle lathe - 2-axis digital readout "D60-2V" Gjdjzbc Dtepfx Acmokb - three-jaw chuck - Folding lathe chuck guard - chuck key - MULTIFIX steel holder with 3x inserts - Sliding tailstock - Control panel, front left - infinitely adjustable feeds for flat and top support - Pole-changing drive motor - machine base frame - Chip guard rear panel - Additional accessories such as collet holder Collets etc. - EMERGENCY OFF button at the front

Condition: new, turning length 850 mm turning diameter 400 mm swing diameter over bed slide 245 mm spindle bore 52.0 mm turning speeds 45 - 1800 U/min bed width 260 mm spindle taper DIN 55029 D 1-5 taper in tailstock 3 MK quill travel 120 mm total power requirement 3.0 / 4.5 kW weight of the machine ca. 1255 kg range L-W-H 1900 x 1000 x 1610 mm Equipment: - 3-axis digital display ES-12 V with LCD display Gkodpfxjxaaxwo Acmeb - 3-jaw chuck PS3-200 mm / D5 - Clamping disk 320 mm - Fixed steady rest - passage diameter max. 130 mm - Follow-on steady rest - passage diameter max. 100 mm - Coolant system - Quick-change tool holder with 4 inserts - Protective device for quick-change tool holder - Micrometer longitudinal stop - Slip clutch - Motor with magnetic brake in accordance with CE standard - Initial filling with Shell Tellus 46 - Extendable chip tray - LED machine light - Change gears - Reduction sleeve - 2 centering points - Chip rear wall - Operating tool