Used Base for sale (7,451)

Condition: used, Year of construction: 2013, operating hours: 97,817 h, machine/vehicle number: S0631C0211, controller model: Simatic IPC627, laser power: 3,000 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 600 mm, Note: The machine indicates an error, which suggests a defect in the beam source. The replacement parts recommended by Trumpf cost approximately €30,000. TECHNICAL DETAILS Working Area Travel range X-axis: 3,000 mm Travel range Y-axis: 1,300 mm Travel range Z-axis: 600 mm Travel range B-axis: ±135° Travel range C-axis: n × 360° Working height: 605 mm Laser Model: TruDisk 3001 Laser power: 3,000 W Scanning frequency: 10 Hz–100 kHz Axis Speeds Simultaneous axis speed: max. 173 m/min X-axis: max. 100 m/min Y-axis: max. 100 m/min Z-axis: max. 100 m/min B-axis: max. 90 rpm C-axis: max. 90 rpm Accuracy Smallest programmable path increment: 0.001 mm Positioning deviation, linear axes X/Y/Z: max. 0.03 mm Positioning deviation, rotary axes B/C: max. 0.005° Positioning error, linear axes X/Y/Z: max. 0.08 mm Positioning error, rotary axes B/C: max. 0.015° MACHINE DETAILS Control and Data Processing Control model: Simatic IPC627 Hard disk storage: 60 GB Color monitor: 12" TFT Network speed: 100 Mbit/s Modem: 56 kBaud/s Pneumatics and Cutting Gas Connection pressure: min. 6 bar Connection pressure: max. 14 bar Compressed air consumption, machine: approx. 30 Nm³/h Compressed air consumption, short-term: max. 40 Nm³/h Cutting gas working pressure: max. 20 bar Dcjdpfxoz Dvfxs Acpsn Electrical Connection Base machine: 47.0 kVA Laser unit TruDisk 3001: 19.5 kVA Laser unit TruDisk 4001: 27 kVA Cooling unit TruDisk 3001: 9 kVA Cooling unit TruDisk 4001: 12 kVA Operating hours: 97,817 h EQUIPMENT Hard disk with RAID controller USB interface Ethernet network connection RJ-45 connector Support for ET BEUI, TCP/IP, Novell Server, and NTFS file system Solid-state laser from the TruDisk series Fast rotary changer with tooling and control system Scrap conveyor for continuous removal of cut-outs and scrap grids

Year of construction: 2008, condition: used, load capacity: 50 kg, plate length: 2,500 mm, plate width: 1,200 mm, stack height: 1,600 mm, TECHNICAL DETAILS Maximum panel width: 1,200 mm Maximum panel length: 2,500 mm Minimum panel width: 195 mm Minimum panel length: 250 mm Lifting capacity: 50 kg Operating performance: 18 cycles/min Maximum stack height from the ground: 1,600 mm MACHINE DETAILS Total installed power: 15 kW CE safety compliance: Yes EQUIPMENT Removal of the panel stack via powered roller conveyor Vacuum pump WINDOWS control Dedpfx Aoz Ekcnscpjcn The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photo documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8347

Condition: used, Year of construction: 2008, workpiece height (max.): 40 mm, controller model: PowerControl P85, working width: 1,550 mm, working length: 4,175 mm, TECHNICAL DETAILS Dcedpfx Aez Ekfvocpon Working area, X-axis: 4,175 mm Working area, Y-axis: 1,550 mm Maximum workpiece thickness: 40 mm Number of working areas: 2 Traverse speed, X-axis: 80 m/min Traverse speed, Y-axis: 80 m/min Traverse speed, Z-axis: 30 m/min Table system: Beam table with vacuum cups Number of vacuum cup beams: 8 Positioning: CNC-controlled Drilling unit Position: Top Vertical drilling spindles: 20 Horizontal drilling spindles in X-direction: 10 Milling unit Position: Top Controlled axes: 4 + Flex5 Motor power: 15 kW Cooling: Liquid cooling Tool changer: Automatic Sawing unit Position: Top Tool magazine: 2 slots Tool magazine 1: 18 slots Position of tool magazine 1: Rear of the machine Tool magazine 2: 10 slots Position of tool magazine 2: On the machining head MACHINE DETAILS Control system: PowerControl P85 Machine programming software: WoodWOP 5.0 EQUIPMENT Beam table with vacuum cups 8 vacuum cup beams Vacuum pump Automatic tool changer Liquid cooling PowerControl P85 control system WoodWOP 5.0 machine programming software Note: Tools not included The machine will be sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7350

Condition: used, Year of construction: 2008, cutting width (max.): 2,200 mm, controller model: POWERCONTROL, cutting length (max.): 4,300 mm, Equipment: scorer, TECHNICAL DETAILS Maximum panel width: 2,200 mm Maximum panel length: 4,300 mm Maximum main saw blade overhang: 125 mm Maximum feed rate: 80 m/min Saw unit Maximum tool diameter, main saw: 450 mm Motor power, main saw: 13.5 kW Maximum tool diameter, scoring saw: 180 mm Motor power, scoring saw: 2.2 kW Dcedpoz Eklvsfx Acpsn MACHINE DETAILS Control system: POWERCONTROL Lift table, number of levels: 4 Clamping system, clamping jaws: 10 EQUIPMENT Lift table Saw unit Scoring unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 5552

Condition: used, Year of construction: 2010, working width: 230 mm, spindle diameter: 40 mm, working height: 120 mm, controller model: Siemens Simatic Touch-Panel, working length: 8,483 mm, TECHNICAL DETAILS Minimum working height: 6 mm Maximum working height: 120 mm Minimum working length: 370 mm Maximum working length: 8,483 mm Minimum working width: 25 mm Maximum working width: 230 mm Maximum feed rate: 12 m/min Rubber feed rollers: 1 Toothed feed rollers: 4 Total number of feed rollers: 5 Number of machining units: 4 Dedpjz Ekkxefx Acpocn Lower milling spindle Spindle diameter: 40 mm Spindle length: 240 mm Motor power: 4 kW Right milling spindle Spindle diameter: 40 mm Spindle length: 240 mm Maximum tool diameter: 4 mm Motor power: 4 kW Left milling spindle Spindle diameter: 40 mm Spindle length: 240 mm Motor power: 4 kW Upper milling spindle Spindle diameter: 40 mm Spindle length: 240 mm Motor power: 5.5 kW MACHINE DETAILS Control system: Siemens Simatic Touch Panel Total connected power: 24 kW EQUIPMENT CE-compliant safety design The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7243

Condition: used, Year of construction: 2017, VWS Nederland – Top/Base Labeling Machine (R → L) Manufacturer: VWS Nederland Type: Top / Base Labeling Machine (Right → Left) Year of manufacture: 2017 Description The VWS Nederland Top/Base Labeling Machine is designed for automatic labeling of products on both the top and bottom sides. The system operates from right to left (R → L) and is suitable for integration into automated packaging and production lines. This labeling system is commonly used in the food, pharmaceutical, and consumer goods industries where accurate and consistent label placement is required. Technical Specifications - Manufacturer: VWS Nederland - Machine type: Top and bottom labeling machine - Labeling direction: Right → Left (R → L) - Label positions: Top and base (bottom) - Year of manufacture: 2017 - Application: Automatic labeling of trays, containers, and packaged products - Integration: Suitable for inline production and packaging lines Key Features - Automatic top and bottom labeling - Right-to-left product flow - Designed for high labeling accuracy - Suitable for various product sizes and packaging formats - Robust industrial construction Applications - Food packaging lines Djdpsyt Hmvofx Acpscn - Pharmaceutical products - Cosmetics and consumer goods - Industrial packaging operations Condition Used More photos and full specifications: / Manufacturer: VWS Nederland

Year of construction: 2008, condition: used, controller model: Windows XP SP3, power: 9 kW (12.24 HP), working width: 2,500 mm, TECHNICAL DETAILS Maximum working width: 2,500 mm Minimum working width: 510 mm Number of saw blades: 6 + 1 MACHINE DETAILS Control system: Windows XP SP3 Machine programming software: Packsize control console 3.9.3 Total connected power: 9 kW Dcjdpfx Aez Ekd Eocpjn EQUIPMENT Saw carriage CE conformity The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents with a descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8534

Condition: used, Year of construction: 2004, workpiece height (max.): 60 mm, workpiece width (max.): 2,800 mm, workpiece length (max.): 1,300 mm, edge thickness (max.): 20 mm, feed rate X-axis: 40 m/min, The machine has the following configuration: Gluing Gluing system: EVA Adhesive application: single-sided and double-sided Scoring saw Motor power: 2.2 kW Speed: 6,000 min⁻¹ Profiling unit Motor power: 6.6 kW Speed: 6,000 min⁻¹ Cross-cutting saw unit Number of motors: 2 Edge trimming unit, top and bottom Number of motors: 2 Motor power: 1.85 kW Speed: 12,000 min⁻¹ Edge rounding unit Number of motors: 2 Motor power: 1 kW Speed: 12,000 min⁻¹ Profiling unit with automatic, time-controlled engagement Motor power: 6.6 kW Speed: 6,000 min⁻¹ Profiling unit with automatic, time-controlled engagement Motor power: 6.6 kW Speed: 6,000 min⁻¹ Belt sanding unit Motor power: 2.2 kW Belt sanding unit Motor power: 0.75 kW Brushing unit Motor power: 0.75 kW Brushing unit TECHNICAL DETAILS Workpiece length: 280–1,300 mm Workpiece width: 320–2,800 mm Workpiece thickness: 8–60 mm Edge thickness: max. 20 mm Feed speed: max. 40 m/min MACHINE DETAILS Control system: ICOS OPEN EQUIPMENT Chain conveyor with drive shoes Pressure bar with rubber belt Edge heating lamps Dcodpfx Aez Ekczscpsn Roller magazine Hot-melt adhesive tank Hot-melt adhesive pre-melter Edge pressing unit with 9 pressing rollers CE-compliant The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents with a descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 6561

Condition: used, Material: 1095 High Carbon Steel Tensile Strength: 120,000 PSI Shear Strength: 96,000 PSI Thickness Range: .0045" - .025" Line Direction: Left to Right Cut Width & Thickness .0045" = 1/4" , 3/8" , 1/2" , 3/4" , 1" .0051" = 3/8" , 1/2" , 5/8" , 7/8" .0062" = 3/8" Line Speed: 1500 FPM Entry Strip Width: 18' Traverse Wider Coil Width: 8" Entry Coil ID: 15" - 22" Traverse Winder Coil ID: 11" Exit Coil ID: 16" Entry Coil OD: 54" Ribbon Wound Coil OD: 39" Exit Coil OD: 54" Entry & Exit Coil Weight: 10,000# Traverse Winder Coil Weight: 2250#` Complete Line With: Mandrel Uncoiler Hold Down Roll 3 Leaf Hydraulic Expansion 15 HP Drive Disc Drake Edge Control Unit Peeler Table / Deflector Roll Newcor Strip Welder with Planishing 2 Roll Material: 1095 High Carbon Steel Tensile Strength: 120,000 PSI Shear Strength: 96,000 PSI Thickness Range: .0045" - .025" Line Direction: Left to Right Cut Width & Thickness .0045" = 1/4" , 3/8" , 1/2" , 3/4" , 1" .0051" = 3/8" , 1/2" , 5/8" , 7/8" .0062" = 3/8" Line Speed: 1500 FPM Entry Strip Width: 18' Traverse Wider Coil Width: 8" Entry Coil ID: 15" - 22" Traverse Winder Coil ID: 11" Exit Coil ID: 16" Entry Coil OD: 54" Ribbon Wound Coil OD: 39" Exit Coil OD: 54" Entry & Exit Coil Weight: 10,000# Traverse Winder Coil Weight: 2250#` Complete Line With: Mandrel Uncoiler Hold Down Roll 3 Leaf Hydraulic Expansion Sliding Base 15 HP Motor 15 HP Motor Disc Brake Edge Control Peeler Table / Deflector Roll Newcor Strip Welder with Planishing 2 Roll Bridal Unit for Tension Control Double Roll Tracking Roll for Strip Alignment 2 Sets of Rubber Coated Deflector Rolls Edge Guides Andritz Slitter Head New in 2016 5" Diameter Arbors 12 Sets of Quick Change Tooling Arbors Pre-Packed Arbors Shimless Tooling Anti Friction Bearings 25 HP DC Drive, 1750/2000 RPM Scrap Baller Dcjdpfx Acoztc Tdepen Recoiler 16" Diameter Drum 10,000# Coil Capacity 30 HP DC Drive Hydraulic Push-Off Hold Down Roll 21" Drum Face 1 Arm Exit Turnstile Vertical Strand Separator Aligns Strips after Exiting the Slitter Deflector Rolls 12 Oscillating Recoilers 11" Diameter Drums Hydraulic Push-Off Vertical Edge Conditioners S Bridal Strip Tension Rolls (2) Hydraulic Traversing Oscillating Wheel 7.5 HP Drive 1 Arm Exit Turnstiles Powerflex Digital Drives 755 Allen Bradley PLC Digital Drives Digital Readouts Central Hydraulic Units Operator Push Button Stations Slitter Tooling Hydraulics & Electrics

Condition: used, Year of construction: 2014, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, working width: 3,200 mm, The machine has the following configuration: Number of machining units: 8 Pressure bar: With rubber belt Panel support stop: Present Overpressure: Present CNC positioning: Present Panel infeed trimming system: Present Number of units in the trimming area: 1 Number of units in the edge processing area: 6 Trimming unit Unit: Flush trimming unit Manufacturer/Model: RT30 Automatic time intervention: Present Motor power: 3.5 kW Speed: 9,000 RPM Edge banding Glue application system: EVA Heating lamps for edges: Present Edge magazine: Roller magazine Number of magazine positions: 6 Hot melt glue tank: Present Hot melt glue pre-melter: HM20 Pressure roller unit: Present Number of pressure rollers: 4 CNC positioning: Present End capping unit Manufacturer/Model: IT90-S Number of motors: 2 Maximum processing speed: 28 m/min Motor power: 0.65 kW Speed: 12,000 RPM Corner milling unit Manufacturer/Model: RF10 Number of motors: 2 Motor power: 1 kW Speed: 12,000 RPM Dcjdpfx Acsz Ekh Depsn Corner rounding unit Manufacturer/Model: AR30 Number of motors: 2 Automatic tool changer: Present Maximum processing speed: 18 m/min Motor power: 0.65 kW Speed: 12,000 RPM Edge scraping unit Manufacturer/Model: RB40 CNC positioning: Present Glue scraping unit Manufacturer/Model: RC20 Brushing unit Manufacturer/Model: SZ30 Number of motors: 2 Motor power: 0.37 kW Speed: 1,400 RPM TECHNICAL DETAILS Minimum panel height: 10 mm Maximum panel height: 60 mm Minimum panel length: 150 mm Minimum panel width: 100 mm Maximum panel width: 3,200 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed rate: 25 m/min MACHINE DETAILS Electrical connection power: 25 kW EQUIPMENT CE conformity The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 5062

Year of construction: 2019, condition: good (used), Pallet wrapper, – used –: Price ex works: €1,950 (net), including loading! Manufacturer: Robopac Model: Ecoplat Plus Base Type: Rotary Table Serial number: 30188020 Year of manufacture: 2019 Turntable diameter: approx. Weight: approx. 345 kg 230 V, 50 Hz, 8.5 A, 1.2 kW Manufacturer data: Length (mm) 2490 mm Width (mm) 1640 mm Height (mm) 2610 mm Film width max. (mm) 500 mm Film thickness min. (µm) 17 µm Film thickness max. (µm) 35 µm Film core diameter max. Ø (mm) 76 Ø mm Film roll diameter Ø (mm) 300 Ø mm Film stretching: Manual Film pre-stretch min. (%) 0 % Film pre-stretch max. (%) 0 % Film roll weight (kg) 20 kg Film carriage type FRD Film carriage speed max. (m/min) 4 m/min Processable product length max. (mm) 1200 mm Processable product width max. (mm) 800 mm Processable product height min. (mm) 400 mm Processable product height max. (mm) 2200 mm Pallet processing capacity (pallets/h) 30 pallets/hr Dsdpfx Ajzpf Rdscpjcn Rotation speed min. (rpm) 4 rpm Rotation speed max. (rpm) 10 rpm Condition: good Available: immediately Location: Erfurt area, later in Frankenberg warehouse

Condition: like new (used), Year of construction: 2016, functionality: fully functional, machine/vehicle number: 25582, Equipped with: Fanuc 30ia Control Hydraulic System Coolant System Chip Conveyor Pneumatics Lube System Jib Crane Change Gears Mist Collector Transformer Work Light Stack Light Specifications: Dodpfxozn Ayme Acpocn Extreme Ratio: 10:1 Root Angle Range (B-Axis): -5 deg. TO 90 deg. Equivalent Root Angle Range: -8 deg. to 90 deg. (Equivalent refers to cradle type machine.) Face Hobbing: Examples of Maximum Gear Pitch Diameter -35 Degree Spiral -152 mm TRI-AC Cutter w/13 Blade Groups Max. Full Depth: 0.550" Max. Face Width: 1.6" Face Milling: Examples of Maximum Gear Pitch Diameter -35 Degree Spiral -7.5" Diameter Cutter Max. Full Depth: 0.625" Max. Face Width: 1.6" Max. Swinging Base Travel (B-Axis): -5 deg. to 90 deg. Max. Vertical Travel (Y-Axis): -4" to 7" Max. Horizontal Travel (X-Axis): -6" to 4" Sliding Base Travel (Z-Axis): 2" to 12" Machine Center to Work Spindle Face (Fixed): 4.5" Tooth Number: 5 to 200 Inclusive Cutting Diameters: Conventional Face Milling: 1.1" to 7.5" Helixact: 100mm to 200mm Fine Pitch: 102mm to 152mm Coarse Pitch: 152mm only Speeds: B-Axis--Swinging Base (Degrees per Second): 30deg./sec. A-Axis--Work Spindle (Face Milling)(RPM): 0-75 A-Axis--Work Spindle (Face Hobbing)(RPM): 0-375 C-Axis--Cutter Spindle (RPM): 30-500 X-Axis--Horizontal (Inches per Second): 4.92"/sec. Y-Axis--Vertical (Inches per Second): 4.92" Z-Axis--Sliding Base (Inches per Second): 4.92"/sec. Work Spindle: Diameter of Taper at Large End (#39 Taper): 3-29/32" Taper per Foot: 39/64" Depth of Taper: 3" Floor Space: 95.75" x 63.5" Height (less mist collector): 90.75" Approx. Weight: 22,000 lbs

Condition: like new (used), Year of construction: 2022, functionality: fully functional, mount diameter: 38 mm, clamping range: 38 mm, Reishauer clamping device, base unit, basic chuck FK 38 suitable for Reishauer gear grinding machine, fits on the spindle for grinding machines RZ 150 / RZ160 / RZ 260 clamping diameter 38 mm for n max. = 3,000 rpm balanced with clamping stroke control / 3-point support control and media feed for additional functions: clamping / air system control / clamping stroke monitoring incl. assembly and operating instructions, as well as Reishauer wooden transport container as new – hardly used, from our stock 2 units available Price negotiable Our asking price is € 3,990.00 net ex works, plus packaging costs Dcedowzkcxepfx Acpen All technical specifications are subject to printing errors and changes. We only sell to countries within the European Community.

Condition: used, Year of construction: 2010, controller model: PC85, working width: 1,750 mm, milling spindle speed (max.): 24,000 rpm, working length: 6,000 mm, TECHNICAL DETAILS Machining method: Drilling and milling Number of work areas: 2 Work area X-axis: 6,000 mm Work area Y-axis: 1,750 mm Number of controlled axes: 5 Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Table system: Console work table with vacuum cups Number of vacuum consoles: 10 CNC positioning: Yes Vacuum cups for workpiece clamping: Yes Number of vacuum cups: 40 Drilling unit Number of drilling units: 1 Position of drilling unit: Top Vertical drilling spindles: 20 Horizontal drilling spindles, X-direction: 5 Horizontal drilling spindles, Y-direction: 5 Total drilling spindles: 30 Milling unit Number of milling units: 1 Position of milling unit: Top Controlled axes: 5 Motor power: 12 kW Speed: 24,000 rpm Liquid cooling: Yes Automatic tool changer: Yes Number of tool magazines: 1 Tool positions: 72 MACHINE DETAILS Control: PC85 Programming software: WoodWOP 5.0 Vacuum pumps: 2 Individual output per vacuum pump: 250 m³/h Total connected power: 49 kW EQUIPMENT Console work table with vacuum cups 10 vacuum consoles with CNC positioning 40 vacuum cups for workpiece clamping 2 vacuum pumps Top drilling unit with 30 drilling spindles Top 5-axis milling unit with 12 kW electric motor spindle Liquid cooling Automatic tool changer Tool magazine with 72 tool positions PC85 control WoodWOP 5.0 programming software Automatic chip extraction Dedpfxsz Ekb Do Acpjcn Safety mats on the front of the machine Safety sensors Fixed safety guards CE conformity The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8167

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Dodpfoihf Ufsx Acpecn Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Condition: used, Year of construction: 2011, working width: 1,300 mm, workpiece height (max.): 50 mm, working length: 3,000 mm, TECHNICAL DETAILS Working area, X-axis: 3,000 mm Working area, Y-axis: 1,300 mm Maximum workpiece thickness: 50 mm Number of working areas: 2 Number of controlled axes: 3 Drilling units Number of drilling units: 4 Drilling unit 1: Top Vertical drilling spindles: 51 Horizontal drilling spindles in X-direction: 4 Drilling unit 2: Top Vertical drilling spindles: 51 Horizontal drilling spindles in X-direction: 4 Drilling unit 3: Bottom Horizontal drilling spindles in Y-direction: 42 Drilling unit 4: Bottom Horizontal drilling spindles in Y-direction: 42 Dcedpfx Acsz Ekggjpsn Milling units Number of milling units: 2 Milling unit 1: Top Controlled axes: 3 Motor power: 6.6 kW Milling unit 2: Top Controlled axes: 3 Motor power: 6.6 kW Sawing units Number of sawing units: 2 Sawing unit 1: Top Design: Fixed unit for grooving in X-direction Maximum tool diameter: 125 mm Sawing unit 2: Top Design: Fixed unit for grooving in X-direction Maximum tool diameter: 125 mm EQUIPMENT Albatros machine programming software Collets for workpiece clamping The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 5446

Condition: excellent (used), Year of construction: 2015, operating hours: 1 h, functionality: fully functional, machine/vehicle number: Z000071400101, total width: 1,400 mm, total length: 2,050 mm, total height: 2,150 mm, type of input current: three-phase, overall weight: 1,100 kg, Powerful industrial blower suitable for a variety of applications. The stationary fan with a 600 mm diameter can be used for cooling, ventilation, heat dissipation, or for displacing water mist and dust. The unit has four rollers and forklift pockets for loading. Electric motor power (blower): 15 kW Air flow rate: 33,000 m³/h Speed: 13.8 kW / 1470 rpm Electrical connection: 400 volts / 50 Hz / 32 amps Cable length: 5.0 m Dsdswbfm Sjpfx Acpocn Pickup and inspection available in D-89188 Merklingen.

Condition: used, Slitting line SECO 60″ x 0.375″ x 50,000Lb (A3791) is perfect solution for longitudinal coil metal cutting into strips with maximum metal thickness 0.375” and maximum coil width 60” Cold Rolled and Hot Rolled Steel 18-60” Strip Width 2 Speed Gear Box 200-500 FPM Thickness: .032″-.375” Complete Line with the Following Components: L-Type Entry Coil Car 40,000# Max Coil Weight Uncoiler: Coil ID: 23-30.50” Coil OD: 72” Maximum Coil Weight: 40,000# Maximum Sliding Base Hydraulic Expansion Peeler and Hold Down Roll Dodpfxetiy Nte Acpjcn 5 Roll Coil Breaker Entry Adjustable Edge Guides Entry Crop Shear Slitting Head: 10” Arbors 40 HP Motor Drive 2 Scrap Winders Recoiler: Coil OD: 72” Max Coil ID: 24” 150HP DC Motor 3 Arm Exit Turnstile 40,000# per Arm Motorized Turn Complete Line with Knives, Rubbers, and Spacers Controls, Hydraulics, and Electrics

Condition: good (used), functionality: fully functional, Raimondi BI-Bulldog Edge Processing Machine For sale: a Raimondi BI-Bulldog in excellent condition. The machine has been used very little and is accordingly well-maintained. 2 processing units / motors For tiles and natural stone Dcsdpfozzru Tjx Acpen Edge, bevel, and bullnose/45° processing Very good, well-maintained condition Inspection and test run possible by arrangement.

Condition: used, Year of construction: 2005, feed rate X-axis: 60 m/min, plate length: 2,500 mm, plate width: 1,200 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum plate width: 1,200 mm Maximum plate length: 2,500 mm Minimum plate width: 220 mm Dcedpjz Ekfcsfx Acpen Minimum plate length: 250 mm Maximum feed rate: 60 m/min EQUIPMENT 90° transfer conveyor CE safety compliance The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and is responsible for the installation, securing, and use of the machine at the destination. External reference: 5981

Condition: used, Year of construction: 2015, functionality: fully functional, Hard Metal Carbide Grinding Lapping Machine Magnetic base Fully PLC controlled Dcodpfxoziw Eaj Acpjn Grinding Length Capacity 600 mm Grinding Motor 2.20 kW / 3 hp External Diameter of Grinding Wheel 150 mm / 6” Grinding Wheel Speed 3450 rpm Feed/Pump Gear Motor 0.25 kW / .3 hp Grinding Wheel Feed per Stroke Manual 0.05 mm Coolant Pump Capacity 20 L/min Magnetic Chuck Width 90 mm / 3.5” Carriage Feed Speed 1.0 mpm Electrics 400/3/50

Condition: used, Year of construction: 2018, power: 4 kW (5.44 HP), workpiece height (max.): 45 mm, TECHNICAL DETAILS Maximum workpiece thickness: 45 mm Minimum panel height: 10 mm Maximum panel height: 45 mm Edge banding unit: 1 MACHINE DETAILS Total installed power: 4 kW EQUIPMENT CE conformity Glue reservoir: For hot melt adhesive Dcedpfxoz Ekbwe Acpon The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents for descriptive purposes. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 7247

Year of construction: 2019, condition: used, functionality: fully functional, machine/vehicle number: 460923-80034645-001, This is an under-counter refrigeration unit from the manufacturer NordCap, which is perfectly suited for installation under existing cooking ranges or grill stations. The unit was manufactured by the premium manufacturer Ideal. The under-counter refrigeration unit features a built-in stainless steel evaporator and is equipped with 4 full-extension drawers. The usable height is 90 mm per drawer. Two identical units are available for sale. The unit has been inspected in our in-house workshop and is fully functional. The unit was only used for 6 months and was stored due to the business closure. Condition: very good (used). The list price is €5,500 net. You will receive an invoice with VAT shown. Our used equipment service for you: Dodpfxozu Saps Acpocn * 6 months warranty on all electrical parts, limited to the replacement of defective parts, excluding installation and removal costs * High-quality brand-name equipment at fair prices * Professional overhaul/inspection & expert cleaning * Inspected & fully functional - or money back * Shipping or self-collection can be flexibly selected * Competent advice - before and after purchase * Provision of operating instructions, connection diagrams & spare parts * Inspection according to DGUV V3 Technical data: * W x D x H: approx. 1380 x 660 x 410 mm * Power connection: V: 230 / kW: 0.265 * Serial number: 460923-80034645-001 * Year of manufacture: 2019 Condition: used, inspected, fully functional Shipping: * Delivery or self-collection by arrangement * Worldwide shipping on request * Shipping to islands or mountain stations only by arrangement Do you have any questions, would you like to receive advice or would you like to see something on site? You can reach us by telephone during our opening hours: Monday to Friday from 9:00 a.m. to 1:00 p.m. and from 2:00 p.m. to 5:00 p.m. Subject to changes and errors. The sale is exclusively subject to our general terms and conditions (GTC), which can be found under the link "Legal Information".

Condition: good (used), Year of construction: 2019, Schulte Storage Technology Pallet Rack Basic Unit Manufacturer: Schulte Storage Technology Rack Type: Basic Rack Upright Type: S610-M18 Overall Length: 2700 mm Rack Height: 4500 mm Rack Depth: 1100 mm Clear Bay Width: 2700 mm Upright Type: LNS-Duo 110 x 50 x 2700 mm Number of Storage Levels: 4 (including ground-level space) Number of Bays: 3 Max. Shelf Load: 2580 kg Max. Bay Load: 8200 kg Pallet Spaces: 12 Scope of Supply: 02 x Schulte Pallet Rack Upright 4500 x 1100 mm blue 06 x Schulte Pallet Rack Beam 2700 x 110 x 50 mm 2580 kg orange incl. safety pins Your partner for safe warehouse logistics: Assembly, disassembly & rack inspection An efficient warehouse is the backbone of your success. We ensure that your racking systems are installed correctly and meet all safety standards. As experts in storage technology, we offer you everything from a single source: Assembly & Disassembly Whether it’s a new installation, conversion, or warehouse relocation – we handle the professional assembly and disassembly of your systems: - Pallet racks (heavy-duty & standard) - Shelving racks for small parts and archives Dcjdpfxszrlkvj Acpen - Warehouse mezzanines for optimal space utilization Rack Inspection & Testing according to DIN EN 15635 Safety is a legal requirement. We perform the annual expert inspection (according to DGUV Rule 108-007): - Inspection for deformations and damage. - Check of safety pins and load plates. - Creation of a legally sound test report including a test label. “Everything from a single source: We would be happy to offer you a suitable bank financing option for your project.” More items – new and used – can be found in our shop! International shipping costs on request!

Condition: good (used), Com J240/30 Banding Machine on a Base One of the most recognizable banding machine manufacturers on the market, manufactured in Japan. The machine operates in manual or automatic mode. Production version, for heavy loads. The machine is mounted on a standalone structure with wheels for transport. Operates on jumbo rolls. After inserting the material, the machine wraps it with tape, compresses, and seals it, creating an elegant package. Ideal for packaging business cards, leaflets, and other materials. Technical specifications: Tape width: 30 mm Performance: 26 cycles/min Dimensions of the banded product: 240 x 150 mm Dcjdozyz Duspfx Acpen Made in Japan. Weight: 70 kg.