Used Carpet Paternoster for sale (448)

Condition: new, Year of construction: 2026, Equipment: safety light barrier, 1A Gmatick Storage Paternoster (roll rack) The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² Ledpsff Huwjfx Akqohn • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden

Condition: used, Year of construction: 1989, Gewinner Euromat Type: Gewinner Euromat Machine No.: 120-50508-18 Year: 1989 Machine height: approx. 5600 mm Machine width: approx. 3300 mm Machine depth: approx. 1450 mm + 330 mm table top Ledoya Dkljpfx Akqshn Number of trays: 18 Tray width: approx. 2450 mm Tray depth: approx. 520 mm Tray height: approx. 500 mm Compartment load capacity: 510 kg Total load capacity: 9100 kg Colour: Beige front / corners blue

Year of construction: 2003, condition: used, functionality: fully functional, empty load weight: 3,500 kg, total length: 1,600 mm, load capacity: 42,000 kg, Tragedorn Load center: 1200 ISO class: Terminal West Lodpfx Aksz Evnvjqjhn Condition: Ready for use and fully functional Technical condition: very good Description: Length: 1600 mm, Diameter: 400 mm

Condition: good (used), Kardex Type: SYS - 250-4010-5-13 Device No.: 26596 Year of Manufacture: Lhedpfx Akezk Ew Hjqsn Device height: approx. 6000 mm Device width: approx. 3000 mm Device depth: approx. 1100 mm + 350 mm tabletop Number of trays: 40 Tray width: approx. 2500 mm Tray depth: approx. 410 mm Tray height: approx. 230 mm Tray load capacity: 150 kg Total load capacity: 6000 kg Color: Gray Device C in the photo.

Condition: good (used), Kardex Type: IND 400 Equipment No.: 25377 Year of manufacture: Equipment height: approx. 6000 mm Equipment width: approx. 2920 mm Equipment depth: approx. 1100 mm + 350 mm tabletop Number of trays: 34 Tray width: approx. 2250 mm Tray depth: approx. 350 mm Tray height: approx. 260 mm Load per tray: 257 kg Total load: 8738 kg Color: Gray Lhedpfx Aozk Ewgjkqen Equipment A in the photo.

Condition: good (used), Kardex Type: IND 250-4010-5-13 Equipment No.: 122/25922 Year of Manufacture: Equipment height: approx. 6000 mm Equipment width: approx. 3000 mm Equipment depth: approx. 1100 mm + 350 mm tabletop Ledpjzk Ewysfx Akqjhn Number of trays: 40 Tray width: approx. 2500 mm Tray depth: approx. 410 mm Tray height: approx. 230 mm Tray load capacity: 195 kg Total load capacity: 7500 kg Color: Gray Equipment B in the photo.

Year of construction: 1991, condition: used, functionality: fully functional, empty load weight: 1,015 kg, total length: 1,690 mm, load capacity: 10,000 kg, Tragedorn Lhedpfx Aez Ewiuokqjn Load center: 850 Condition: Ready for use and fully functional Technical condition: good Description: Length: 1690 mm, Diameter: 400 mm

Year of construction: 2012, condition: good (used), Type: IND-PA Device No.: 0/1220744/1 Year of manufacture: 2012 Device height: approx. 5600 mm Device width: approx. 2870 mm Device depth: approx. 4000 mm Number of rollers: 45 Lhsdpfx Akohyhlgeqsn Roller width: approx. 2370 mm Shelf load capacity: 200 kg Total load capacity: 9000 kg Color: beige

Condition: ready for operation (used), Year of construction: 1991, A roll paternoster ESKA storage and loading system is available. Roll width: 1600mm, max. load capacity: 2800kg, total height: 4300mm. Documentation available. An on-site inspection is possible. Lhjdpfxjw I E Dcj Akqjn

Condition: like new (used), Year of construction: 2019, We now have two Kardex Megamat RS 650 units available. Both machines were manufactured in 2019 and put into operation in 2020. They have been serviced annually by the manufacturer and are in very good condition. The Kardex Megamat RS 650 is a powerful vertical carousel designed for storing and handling heavy goods. Each carrier (base shelf) can hold up to 650 kg, making the machines suitable for storing large and heavy items. The two machines have a total of 34 carriers (base shelves) and 43 trays: 28 carriers without intermediate shelves, with a height of 348 mm 3 carriers with two intermediate shelves, providing a total of 9 trays with a clear height of 115 mm 3 carriers with one intermediate shelf, providing a total of 6 trays with a clear height of 170 mm The machines are also equipped with a Matrix display in the access opening. This LED display shows information such as the picking location, quantity, and other useful details. The Matrix display helps reduce search time and the risk of picking errors, making the picking process faster and easier. To utilize the full functionality of the Matrix display, the machines need to be connected to an ERP or Warehouse Management System (WMS). Technical Information: Model year: 2019 Model: MEG RS 650.1.3250.6.406.34 Machine height: 7,835 mm Machine width: 3,975 mm Machine depth: 1,711 mm Number of carriers: 34 Number of shelves: 9 Maximum carrier height: 348 Carrier width: 3250 Carrier depth: 628 Electronics: 3/N/PE 400V, 20A Lodpfx Akoz Aiwbsqshn

Condition: excellent (used), Year of construction: 1994, functionality: fully functional, Very well-maintained and robust Heesemann MFA 8 wide belt sanding machine for professional use. The machine is particularly suitable for surface, fine, and finish sanding and features electronic control as well as cross and longitudinal sanding units. The machine is in very good used condition. Technical data: Ledpfxjzxyfhj Akqehn Manufacturer: Heesemann Type: MFA 8 Year of manufacture: 1994 Machine number: 9411252 Working width: approx. 1,300 mm Cross belt: 4,800 × 150 mm Pressure pad belt: 4,450 × 140 mm Longitudinal sanding belt: 2,100 × 1,350 mm Voltage: 400 V Frequency: 50 Hz Total connected power: approx. 50 kW Rated current: 100 A Sanding belt dimensions: 4,800 × 150 mm Pressure pad belt: 4,450 × 140 mm Constant working height Electronic control Cross belt unit Longitudinal sanding unit Brush units Suitable for finish, fine and surface sanding Weight: approx. 4,000 kg Equipment: Electronic control panel Pneumatic unit adjustment Feed carpet Dust extraction connections CE marking Transport possible for an extra charge! The machine is currently still at the customer's site but would be immediately available! The machine will be inspected before sale. For used machines manufactured in 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale, and changes are subject to change. All information without guarantee.

Condition: like new (used), Year of construction: 2019, operating hours: 137 h, T45 thicknesser by Martin with Tersa cutterhead Planing width approx. 630mm Planing height adjustable electrically from 2.8 to 300mm, with digital display providing readings in 1/10mm increments and positioning control The control system also offers the option of incremental adjustment, i.e., you can set a value such as 1mm and then, by repeatedly pressing the start button, change the planing height by 1mm each time without having to set a new absolute height each time. Furthermore, 99 fixed values can also be stored as a program. Drive motor 5.5kW with automatic motor brake 4-knife Tersa cutterhead with new knives Feed rate 6 + 12m/min Rubber-coated infeed roller Rubber-coated outfeed roller Planed machine table guided on four threaded spindles and guides for optimum stability Low-noise design with soundproof hood Dust extraction port 160mm Emergency stop at the front and rear New Tersa knives Operating manual CE marking Lhsdpfxoz Icvle Akqen Original paint, not repainted Carpet in original condition No scratches on the table! Only 137 operating hours, i.e. only 25 minutes per week!!! Dimensions approx. 1200 x 1300 x 1250mm (LxWxH). Weight approx. 1200kg. The machine can be demonstrated on site by appointment. We only offer machines that are readily available in our warehouse for demonstration, see "other offers from this provider".

Condition: excellent (used), Year of construction: 2023, operating hours: 60 h, functionality: fully functional, machine/vehicle number: AE00003516, grinding width: 1,370 mm, overall weight: 1,800 kg, grinding height: 170 mm, workpiece height (max.): 170 mm, workpiece width (max.): 1,350 mm, - Wide-belt sanding machine DMC SD 70 RCS 135 - DMC SD 70 model, RCS 135 version First "R" unit with roller and second "CS" combination unit with roller/sanding pad Lsdjzydafopfx Akqehn - Working width mm 1,350 Min./Max. working height mm 4-170 Sanding belt dimensions mm 1,370x2,620 Main motor power kW (HP) 11 (15) Feed rate m/min 4.5/9 - 160/85 rubber-coated calibrating roller, diameter 160 mm, 85 Sh - 1st position - R160/45 rubber-coated sanding roller, diameter 160 mm, 45 Sh - 2nd position - Hard sanding pad with manual adjustment of the working height - Motor power, 1 unit: 11 kW (15 HP) - Electronic ammeter for the main motor to display current draw - Electronic display of the working height - Electronically controlled sanding belt oscillation - Rubber pressure rollers - Kickback protection at the infeed before the first unit - Rubber feed carpet, 60 SH - Roller table with two rollers at the infeed and outfeed of the work table - Carpet feed with two speeds 4.5 / 9 m/min with gear motor - Automatic carpet centering

Condition: good (used), Year of construction: 2011, We now have two Kardex Shuttle XP 500 units, 3050 x 813 mm, from 2011 available for sale. The machines are in good condition and have been regularly serviced since installation. The Kardex Shuttle XP 500 is a reliable and proven storage system used by thousands of companies worldwide. Each tray is 3,050 mm wide and 813 mm deep, providing 2.5 m² of storage space. The system offers a total of 112.5 m² of storage space while using only 9.87 m² of floor space. Technical Information: Model year: 2011 Model: SHUTTLE-XP-500-3050x813 Machine height: 7,500 mm Lhodpjzybfxefx Akqen Machine width: 3,380 mm Machine depth: 2,921 mm Tray width: 3,050 mm Tray depth: 813 mm Number of trays: Approx. 45 / machine Maximum weight per tray: 210 kg Electronics: 3/N/PE 230/400V 17A

Condition: new, We supply and install our own, new, digital PLC controllers suitable for warehouse lifts and paternosters from all major manufacturers on the market. Our LTG StoreControl LL (warehouse lifts) and LTG StoreControl P-Touch (paternoster) controllers thus offer replacements for controllers for which spare parts are no longer available. Our controllers easily connect your dynamic storage systems to higher-level warehouse management systems and implement access restrictions. Ljdpfx Akoqlb Smsqjhn

Year of construction: 2007, condition: ready for operation (used), A vertical carousel storage system (office lift) Hänel with front access is available. Trays: 18, tray arrangement: 4-lane, max. stack load per tray: 132kg, machine dimensions X/Y/Z: approx. 3300mm/1000mm/2850mm, weight: approx. 3000kg, control: MP0A. Documentation available. An on-site inspection is possible. Ledpfx Aksyiflgoqjhn

Year of construction: 2003, condition: good (used), Type: TLI 4500/2044 Device No.: 03502 Year of Manufacture: 2003 Device Height: approx. 4500 mm Device Width: approx. 2000 mm Device Depth: approx. 7010 mm Number of Rollers: 44 Lsdpshyhlksfx Akqshn Roller Width: approx. 1680 mm Shelf Load: 150 kg Total Load: 7000 kg Superstructure: see photo, 3000 mm Color: beige

Condition: reconditioned (used), modernized machine with new LTG StoreControl P control system External dimensions: Overall height: 5000 mm Overall width: 2650 mm Overall depth: 1250 mm plus 300 mm discharge table 34 carriers, each with a payload of 140 kg in the clear internal dimensions: H = 220 mm W = 2220 mm D = 410 mm Chain pitch: 254 mm Discharge table at 1000 mm above the top edge of the machine frame, with a wooden worktop Color: GRAY, surfaces cleaned, signs of use possible Lhsdpfxednfdlj Akqsn Motor power, drive: 1 x 1.8 kW / 400 Volt Subject to errors and technical changes Delivery and installation currently mainly in Germany, Austria, and several neighboring countries.

Condition: like new (used), Year of construction: 2021, We now have a Vertical Carousel from 2021 available for sale. The machine is in very good condition and has been serviced annually by the manufacturer since installation. The Vertical Carousel has a total height of 6,435 mm, making it suitable for many different types of storage and operations. It has a carrier width of 3,050 mm and a depth of only 428 mm. With 30 carriers, the machine provides a total of 39.2 m² of effective storage space. Lhedpfx Asz Aphaekqon One of the main advantages of this machine is its space-saving design. It only requires approximately 4.7 m² of floor space, making it an excellent solution for companies that want to increase their storage capacity without needing more floor space. The machine also has very low operating hours, indicating that it has been used very little. It has always been kept in a clean and well-maintained environment. Technical information: Model year: 2021 Model: MEG.RS.350.1.3050.4.381.30 Machine height: 6,435 mm Machine width: 3,675 mm Machine depth: 1,271 mm Number of carriers: 30 Maximum carrier height: 320 Carrier width: 3050 Carrier depth: 428 Electronics: 3/N/PE 400V, 16A

Year of construction: 2018, condition: used, - Heating plate format (mm): 2850 x 1550 - Total pressing force (kN): 2400 - Maximum operating temperature: 180 degrees Celsius Vacuum press with 3 paternoster magazines Manufacturer: Wemhöner Type: Variopress - Basic 1000S Year of manufacture: 2018 Technical data Heating plate format (mm) 2850 x 1550 Design of the electric heating plate: Aluminum heating plate on top Total pressing force (kN) 2400 Maximum chamber pressure (bar) 6 Maximum operating temperature 180 degrees Celsius Maximum batch or workpiece size (mm) approx. 2460 x 1180 Thermoplastic film as roll stock, film width: approx. 1430 mm Film thickness (mm) approx. 0.25 - 1 Chamber height (mm) max. up to 180 Connection values: Installed power (kW) approx. 46 Lhedpfxozuz Eue Akqen Required air pressure (bar) approx. 8 Including 3 x paternoster magazines for film rolls Note: The technical data and descriptions are a copy of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, SSI Schäfer Logimat SLL Vertical Storage Lift The SSI Schäfer Logimat SLL is an automated vertical storage lift designed for efficient storage and retrieval of small parts using the goods-to-person principle. It is characterized by high storage density and ergonomic ease of operation. Functions and Advantages Goods-to-person principle: The system automatically brings the requested tray to the access point, minimizing travel distances for personnel. Space optimization: The Logimat measures the height of the stored items and dynamically optimizes the storage height, resulting in very high storage density in a minimal footprint. Ergonomics: The access point (LOGI Gate) can be positioned at different height levels to ensure ergonomic removal. Optionally, the reach depth into the tray can be further reduced, reducing the strain on the operator. Software integration: The storage lift is equipped with a standard PLC control and can be integrated into customer-specific WMS or ERP systems (such as SAP) via interfaces. The in-house software solution WAMAS® Logimat is also available. Robustness: The system features two helical racks that ensure robust, precise, and reliable vertical transport of the tray, even with eccentric loads. The SSI Logimat storage lift is used in many industries for the storage and retrieval of various goods: E-commerce Healthcare & Cosmetics Retail & Wholesale Industry Automotive The application areas of storage lift systems are diverse: Small parts storage Item management Buffer storage for production Order picking Storage and retrieval of maintenance and spare parts Storage of semi-finished products Technical Data Manufacturer: SSI Schäfer Type: SSI Logimat Type SLL Storage Lift Serial No. 916.0498-A2 Serial No. 916.0498-A3 Control, Type PLC-EasyConnect Touch Display Height of storage lift: 6835 mm Width of storage lift / tray: 4570 mm / 4025 mm Depth of storage lift / tray: 3092 mm / 815 mm Load capacity of machine: 2x 25 t Number of levels/trays: 43 Load capacity per level/tray: 590 kg Size of storage locations adjustable Power supply: 400 V 50 Hz Nominal operating current: 24 A Max. power consumption: 17 kVA Total weight of machine: 36 t Year of manufacture: 2016 Side walls missing The storage lifts are arranged in a block configuration, which is why the inner side walls are missing. The professional dismantling, worth €5,000 (net), is already included in the price. Item location: 37308 Geisleden Expand your SSI Schäfer storage lift! A storage lift is only as efficient as its internal layout. Our specially designed storage bins utilize the tray area of your SSI Schäfer system (e.g., LogiMat) to the very last millimeter. Lodpfx Aoyllxzekqehn The containers are available in three different sizes (S, M, L) and enable optimal use of the storage space in the lift system. Find the right dimensions for your system in our other auctions. "One-stop shop: We would be happy to offer you a suitable bank financing option for your project." You can find more storage lifts – new and used – in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, power: 7.5 kW (10.20 HP), planing width: 625 mm, tool diameter: 125 mm, number of blades: 4, rotational speed (min.): 5,000 rpm, overall weight: 1,000 kg, 4-knife TERSA cutter head for planer Ljdpfx Aoz Dkftokqjhn Motor power 7.5 kW Positioning control for the thickness table Segmented infeed roller Segmented pressure bar Feed speeds of 7 + 14 m/min Table extension Planing width 625 mm, chip removal up to 8 mm, planing height 3.5-305 mm Thickness table mounted on four support spindles and with 4-point guidance. Heavily ribbed cast iron table, finely planed Modern control panel ergonomically positioned. Electric thickness table adjustment with LED display. Buttons for adjusting in rapid or slow mode, Adjustment accurate to 1/10 mm; integrated operating hour counter. Electronic starting and braking system. Electronic, wear-free brake for safe stopping of the cutter head. Infeed roller in rubber and two rubber outfeed rollers (high quality, low wear) Segmented pressure bar, rotary knob with scale, for adjusting the pressure (preload) of the outfeed pressure bar Two feed speeds 7 + 14 m/min; electrically switchable, also during planing Thickness hood with carpet support, can be used as a storage area for wood. Dust extraction port Ø 160 mm, to the left (can also be on the right – can be easily converted on site) Air velocity 22 m/s Integrated tool storage compartment for operating tools and planing knives Electrical equipment according to VDE/EN 60204 with main switch, emergency stop button and 2nd emergency stop button on the discharge side, winding protection, undervoltage protection, contact for controlling the dust extraction, accessories: 1 set of knives installed, operating tools, grease gun, operating manual Weight: approx. 1000 kg CE-compliant, BG-Holzstaubgeprüft No. HM 23001 Workplace-related emission values dB(A) according to DIN 45635 Part 1650 Idle noise approx. 69 dB(A), operating noise approx. 79 dB(A) Workplace-related dust emission value: 0.44 mg/m³

Condition: excellent (used), WEINIG UNISTACKER PATERNOSTER STACKER WITH ADDITIONAL HANDLING EQUIPMENT OFFER INCLUDES Lhodjy D Akajpfx Akqon 1. WEINIG 820 RIGHT ANGLE TRANSFER CONVEYOR. 2. WEINIG (5 BELT) 8M LONG SORTING STATION FEEDING TO PATERNOSTER STACKER. 3. WEINIG 811 UNISTACK PATERNOSTER STACKER. 4. 3X STICK MAGAZINES 1200MM. MINIMUM LENGTH APPROXIMATELY 500MM. MAXIMUM LENGTH 3100MM. PACK WIDTH 1200MM PACK HEIGHT 1200MM MAX. CAPACITY 5 LAYERS PER MINUTE 4. WEINIG 802 SCISSORS LIFT ROLLER CONVEYOR FEEDING TO PACK OUTFEED. 5. WEINIG 812 POWERED ROLLER CONVEYOR OUTFEED. 6. WEINIG CHAIN PACK OUTFEED CONVEYOR

Condition: used, mileage: 766,000 km, power: 315 kW (428.28 HP), first registration: 11/2017, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, color: white, gearing type: automatic, emission class: euro6, total length: 9,590 mm, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2017, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, * Mercedes-Benz Actros 1843 with BDF interchangeable body – air suspension front and rear – wheelbase: 5,500 mm * Diesel – engine displacement: 10,677 ccm³ – 315 kW / 430 hp – Euro 6 – Green emissions sticker * Please schedule an appointment for viewing – sale on behalf of a customer * Contact: Mr. Andreas Vogel * The information provided on the internet is a non-binding description. * It does not constitute guaranteed characteristics. * The seller is not liable for typing or data transmission errors. * Subject to changes, errors and prior sale. Special equipment: Front axle load 8.0 t, Airbag driver side, Trailer brake 2-line, Connections on the left, Work lights, Work lights on the rear wall of the cab above, Audio system: CD radio (Bluetooth), Brake connection standard and DuoMatic, Additional compressed air tank, Air horns (2) on the cab roof, Cab: Width 2.50 m, Cab floor flat, Cab: Height 765 mm, Cab: Tilting device electro-hydraulic, Carpet on the engine tunnel, Sun visor side window, Driver's door, Additional 12V socket, Compressed air connection in the cab, Windshield tinted, Holder for Fleetboard Dispopilot, Urea tank (AdBlue): 75 L, Info display 12.7 cm with additional display, Fuel tank: 500 L aluminum, Fuel tank: Additional tank 500 L aluminum, right, Light and rain sensor, Air intake integrated, Air deflector roof (lockable, without base cover), Engine brake reinforced, Retarder, Drawers under the dashboard, Circuit breaker, Seats in the cab: Armrest passenger seat, Seats in the cab: Passenger seat comfort suspension seat, Seats in the cab: Passenger seat backrest foldable, Seats in the cab: Driver's seat comfort suspension seat, Sun visor exterior, Storage compartment left under the cab, 12V socket in the passenger footwell, 24V / 25 A socket in the passenger footwell, Additional thermal insulation Additional equipment: Lsdpfs Adw Uuox Akqehn Emission standard EURO 6, Axle configuration: 4x2, Actros 4, Trailer socket 24V / 15-pin, Exhaust to the right outside, Exterior mirrors electrically adjustable and heated, Differential lock rear axle, Compressed air tank steel, Compressed air unit medium, Cab: L StreamSpace, Cab version: StreamSpace, Lifting roof electrically, Preparation comfort upper bunk, wide, Cab: steel sprung, Comfort, Suspension: Air / Air (full air), Power windows, Generator 100 A, Gearbox 12-speed - Type: G 211-12, Rear axle crown wheel 440, Body/structure: Chassis, Comfort lower bunk, Comfort locking system, Communication interface, Radiator grille, Steering pump regulated, Air compressor 2-stage, Engine 10.7 L - 315 kW R6 Diesel (OM 470), Engine compartment encapsulation, Ramp mirrors, Waste heat recovery, Disc brakes front and rear axle, Seat cover / upholstery: Fabric, Seats in the cab: Driver's seat backrest foldable, Voltage converter 24V / 12V 10 A, Splash guard front, Stabilizer front axle, Storage flap outside left, Socket cab 24V, Tachograph / EG control device, Door extension for cab, Underride guard front, Preparation CB radio, Preparation toll collection, Front axle angled, Water pump regulated, Permissible gross weight 18.00 t, Auxiliary heater (water), Battery 220 Ah

Condition: like new (used), Year of construction: 2016, functionality: fully functional, total height: 11,000 mm, total width: 2,350 mm, total length: 11,395 mm, load capacity per storage section: 35 kg, load capacity: 49,560 kg, For SALE 6 pieces!!! KARDEX Vertical Buffer Module LR35® Machine Type: LR-35-19x400x600x11000 Machine height: 11,000 mm Required installation height: 11,050 mm Machine length: 11,395 mm Machine width: 2350 mm Storage segments: 19 pieces Lhedpfx Ajwqp Npekqjn Bin width: 400 mm Bin depth: 600 mm Max. load (calculated per Bin): 35 kg Machine surface (without "turntable"): 23.49 m² Machine surface (incl. "turntable"): 26.77 m² Permitted total weight: 59,492 kg Permitted total load: 49,560 kg Empty weight (without Bins): 11,415 kg Speed x-axis: max. 3 m/s Speed y-axis: max. 3 m/s Safety intermediate distance: 60 mm Storage grid 25 mm Permitted ambient temperature in operation: +5° - +40° Permitted relative humidity: 85% Year of Build: 2016 Machinehandel De Leeuw BV is one of the few companies in Europe that trades and has in stock mainly used Kardex Remstar VLM automatic Lift (Shuttle systems) & rotating warehouse systems (paternoster systems). See our website for the current stock. We assemble and/or disassemble these systems in a safe manner with VCA certified technicians and we have been doing this for more than 33 years. We also disassemble other brands such as: Hänel, Electrolux, Bertello, Megamat, Lista, Denocard Machinehandel De Leeuw BV Oordeelsestraat 7–b 5111 PA Baarle-Nassau TheNetherlands Email: info at deleeuw-machinehandel.nl