Used Cling for sale (2,353)

Condition: excellent (used), Year of construction: 2017, operating hours: 19,187 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, overall weight: 52,000 kg, Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 140 Year of construction 2017 Working hours 19,187 hours, stand October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm Capacity per cycle time 4,34 m³ Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm Driving motor 2 x 75 kW Connected load 226 kW Full load current 428 A Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 800 up to 1300 kg, depends on material and bale lenght SPS controller (manuf., type) Telemecanique TSX Micro Operating panel (manuf., type) Schneider MAGELIS Touch Baler dimensions built up with hopper 13,200 x 27,000 x 7,344 mm (l x w x h) Transport dimensions only baler 13.200 x 2.750 x 3.450 mm (l x w x h) Machine weight baler approx. 52 tons Technical data chain belt conveyor: Manufacturer Bollegraaf Typ HBT 1216 Year of construction 2009 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Pedpfxsxrta Eo Adyorc Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Weight 16 t Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Comments: The press is currently in operation and is to be replaced by a new machine in the 2nd quarter of 2026. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, make Ambra output 75% mehr Zuzug des Mittel alle Medien Ölbinder Recyling-Pack +++++ Prjdeiqpzgopfx Adysc Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: new, Year of construction: 2025, functionality: fully functional, Young used sink float tank for separating hard plastics, can wash/sort. Predovy Dumopfx Adyec Made of stainless steel 304, also suitable for salt solutions.

Condition: refurbished (used), Year of construction: 2005, functionality: fully functional, overall weight: 30,000 kg, rotor diameter: 800 mm, rotor length: 1,200 mm, power: 250 kW (339.91 HP), Universal granulator, impact granulator, Drive power: 250 kW, control cabinet with star-delta switching Rotor length: 1200 mm, Rotor diameter: 800 mm, Number of blades/rotor: 36 pcs, Number of blades/stator: 4 x 6 pcs, 2 hydraulically rotatable stators each with 2 rows of counter blades, Pedpfx Aexiw Hwedyjrc Hydraulic pusher, Bearing temperature monitoring, Central lubrication for the rotor bearings, Net weight: 29,800 kg, Year of manufacture: 2005, overhauled in 2025, all wear parts replaced. Available from approx. December 2025.

Year of construction: 2013, condition: ready for operation (used), A metal press RMH MB (Mini Baler) by RMH Diebels Recyclingmaschinen is offered. Filling box dimensions: approx. 815mm/350mm/510mm, bale size: approx. 350mm/200mm, pressing cycle: approx. 1min, cutting blades on three sides of the filling box, lid shear force: 20t, bottom ram force: 40t, operating pressure: approx. 220bar, machine dimensions X/Y/Z: approx. 2450mm/1200mm/1400mm, weight: approx. 1800kg. An on-site inspection is possible by appointment. Podpjxn Aayofx Adysrc

Year of construction: 2010, condition: new, functionality: fully functional, Technical specifications: • Manufacturer: JMC Recycling Systems Ltd. (England) • Model: Dolphin 5005-Lite • Year of manufacture: 2010 • Connection: 380–415 V, 3-phase • Recommended hydraulic oil: ISO 46 • Robust construction, mobile on wheels • Includes control unit and hydraulic drive Condition: • NEW, unused Psdoxm Uf Sepfx Adyjrc • Only storage marks present (see pictures) • No operating hours

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a Prjdpfju Thcvox Adyjc bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2024, condition: new, ZIGZAG air separators Application description: ZIGZAG type air separator is a device designed to purify materials in the waste recycling process. The separator separates light fractions from heavy fractions by pneumatic method. It works well with a wide range of waste materials of 0-150mm size. Air separators of this type are used for pre-ground, jagged or very fine materials. Thanks to our unique design, the separator has the ability to adjust at many points that are important for the purity of the received fractions. Pjdpfx Adjua D Alsyerc ZIGZAG type separators are used in many areas: weight classification of metal granules purification of shredded scrap from the light fraction (films, plastics, paper) removal of volatile fraction during recycling of WEEE purification of plastics, rubber purification of municipal waste, glass removal of dust Construction description: The ZIGZAG separator consists of individual components mounted on a common support structure. In the first part, the ZIGZAG module is installed. The module has an inspection hole and regulation of the material stream passage gap. In the second part there is a cyclone discharging the light fraction. Underneath the cyclone there is a variable speed sluice for ejection of separated materials. A fan with electronic speed control is located on top of the structure. The structure is designed in part for loading and unloading by conveyor belts. The separator has a control cabinet equipped with a safety system.

Year of construction: 2023, condition: new, Stock machine Prodpfx Ajhwdvcsdyjc Completely redeveloped high efficiency centrifuge based on our many years of production experience with the predecessor of this centrifuge, we have made various improvements with regard to maintenance costs, downtime and wear and tear parts.

Condition: refurbished (used), Year of construction: 2004, functionality: fully functional, overall weight: 30,000 kg, rotor diameter: 800 mm, rotor length: 1,200 mm, power: 250 kW (339.91 HP), Universal granulator, impact granulator Drive power: 250 kW, control cabinet with frequency inverter (year of manufacture 2019) In 05/2023, the rotor shaft was replaced by an exchange shaft, including new bearings and seals. Rotor length: 1200 mm Rotor diameter: 800 mm Number of knives per rotor: 36 pcs Number of knives per stator: 4 x 6 pcs 2 hydraulically rotatable stators, each with 2 rows of counter knives Hydraulic pusher Bearing temperature monitoring Centralized lubrication system for rotor bearings Net weight: 29,800 kg Year of manufacture: 2004, overhauled in 2025, all wear parts renewed. The granulator is overhauled and workshop tested, delivered ready for connection. Test run/demonstration available by appointment. Prsdow Am Nqopfx Adyec

Year of construction: 2025, condition: new, Zig Zag Air Sifter Sizes/ wides from 200mm - 1800mm Prsdpfochb Ruox Adyoc Precondition for the separation are differences in the material like: - Different sizes of particles - Differences of the density - Differences in the surface condition of the particle - Differences in the form of the particle - Grain size 0.1mm - 40mm, (bigger particles are possible with a special design) We are the manufacturers of these plants and we build Zig Zag Sifter Plants in different sizes see attachment. In order to make you a definite offer we need to know some points: 1. What material you want to separate? 2. Grain-size of the material? 3. Bulk weight kg/liter of your material. 4. We have technical center at our house, where we can test your material.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Prsdpfevf E Avox Adyec Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2024, condition: new, WPS Eddy Current Separator, Magnetic Series. Eddy Current separators from the Magnetic Series are mainly used in the waste recycling industry. The use of eddy currents allows for the recovery of non-ferrous (non-magnetic) metals from loose waste such as aluminium, copper, brass etc. The WPS separators are characterized by high separation accuracy due to the original solutions by ZŁOMIARZE, which guarantees high profitability of waste recycling. WPS Separators are used in the recovery of: • non-ferrous metals from the recycling of electronic waste • non-ferrous metals from car recycling • metals from foundry waste • aluminium in glass recycling processes • non-ferrous metals from steel waste • non-ferrous metals from municipal waste To ensure the longevity of the equipment, the ZŁOMIARZE, as one of few companies, has introduced an improvement in the form of the central cooling of the bearings of the magnetic rotor, thanks to which the service life of the machine has been extended even several times. Technical Specification: • Magnetic field source – NdFeB magnets • Smooth adjustment of magnetic rotor speed – 0-3000 rpm • Belt speed adjustment • Belt position control system • Magnetic rotor cleaning cleats • Belt cleaning scraper • Material divider adjustable in two levels • Bearing cooling system (greatly extends bearing life) • Control panel with safety check For our non-ferrous metal separator we offer additional devices to make you separation process easier: • vibratory feeder Predpfx Adsiqxtboyec • belt conveyors • magnetic drum/belt separators For more information please download our catalog. If you're interested in our products, please contact us!

Condition: good (used), Young used vibrating sieve to filter process water. Pedpfxovy Dy Nj Adysrc Made of 304 stainless steel, also suitable for salt solutions.

Year of construction: 2025, condition: new, To sieve dry material: like flour-, grainy-, and granule-shaped material. Podpfochb Ryex Adyorc Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 layers, granulation 0,1-18mm freely selectable.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Pedpfx Adsu Thkaoysrc Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, rotational speed (max.): 3,000 rpm, nominal power: 22 kW (29.91 HP), Young used centrifuge for drying hard plastics with high efficiency. Pjdpfx Asvy Db Hodyerc Made of 304 stainless steel, also suitable for salt solutions.

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 ply, granlulation < 18mm freely selectable. Predpfx Aebcngisdyec

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour Prodpfxjxbgnhe Adyoc bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, Built on order Vibrating sieve to filter the process water. Process water is preferably used in a closed circuit. The authorities also see this as the ideal solution. Obtaining the permits for a recycling plant is greatly simplified by the use of a closed circuit and the costs of using the plant are significantly lower. Prodpfskzg Sdsx Adysc

Condition: new, Year of construction: 2025, Stock machine Psdpfxskzg Sao Adyjrc Completely redeveloped high efficiency centrifuge based on our many years of production experience with the predecessor of this centrifuge, we have made various improvements with regard to maintenance costs, downtime and wear and tear parts.

Condition: new, Year of construction: 2025, Newly available on order Big-bag filling units are suitable for filling commercial sizes of big bags. The big bags are filled with the product, for example, via screws, rotary valves or a hopper feeder. The big bag stations can be linked and optionally extended with an automatic exchange system. This exchange system ensures that when a full report is received, the filling process is continued to the next big bag station, so the filling process does not stop and there is time to exchange the full big bag. The filling station has a shaking system to compact the product in the big bag during the filling process, so the big bags are filled 10-15% more and therefore also stand up firmly. + Perfectly filled big bags + High filling weight, 10-15% more on average + Stable standing big bags + Quick big bag changeover + Adjustable hooks for different big bag sizes Base station: - Frame size: L150cm x W150cm x H 295cm Predsxnyftspfx Adysc - With pneumatic shaking system - 10-15% more filling - Adjustable height to adapt to different big bag sizes (manually) - Easy operation - Modular construction - Perfectly filled bags - High fill weight - Sturdy upright bags - Quick big bag change - Made in the Netherlands Options: - Executed in stainless steel - Suction transport by hopper feeder with vacuum blower. - Automatic bag-full notification - Switching signal for stop function / sound signal - Automatic switching system between big bag stations upon full notification Safety option: All stations can be supplied with a platform with a handrail on the side you want.

Condition: new, Year of construction: 2025, Newly available on order Big-bag filling units are suitable for filling commercial sizes of big bags. The big bags are filled with the product, for example, via screws, rotary valves or a hopper feeder. The big bag stations can be linked and optionally extended with an automatic exchange system. This exchange system ensures that when a full report is received, the filling process is continued to the next big bag station, so the filling process does not stop and there is time to exchange the full big bag. The filling station has a shaking system to compact the product in the big bag during the filling process, so the big bags are filled 10-15% more and therefore also stand up firmly. + Perfectly filled big bags + High filling weight, 10-15% more on average + Stable standing big bags + Quick big bag changeover + Adjustable hooks for different big bag sizes Base station: - Frame size: L150cm x W150cm x H 295cm - With pneumatic shaking system - 10-15% more filling - Adjustable height to adapt to different big bag sizes (manually) - Easy operation - Modular construction - Perfectly filled bags - High fill weight - Sturdy upright bags - Quick big bag change - Made in the Netherlands Options: - Executed in stainless steel - Suction transport by hopper feeder with vacuum blower. - Automatic bag-full notification - Switching signal for stop function / sound signal - Automatic switching system between big bag stations upon full notification Pjdpfjhbvfqex Adyjrc Safety option: All stations can be supplied with a platform with a handrail on the side you want.

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. The machines are in stock and can therefore be delivered within a week. Predpfoxhf Nwex Adysc Ask us for further information.

Condition: new, Year of construction: 2025, In stock: Prodpfx Ajxhf H Nsdyoc The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. The machines are in stock and can therefore be delivered within a week. Ask us for further information.