Used Cross Breaking for sale (7,098)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Gsdpfx Agju Tg I Do Tsil Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Godjd Ecncspfx Ag Tsil Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment Gjdofv Hphepfx Ag Tjil cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: used, Roller conveyor with chain cross conveyor Can be used after resaw. - Electric motor: 1,1 kW - Electric motor: 0,75 kW - Electric motor: 1,1 kW Giodpsi Sdk Sjfx Ag Tsl

Condition: used, Year of construction: 2003, The Mueller Martini CB 16 stacker, manufactured in 2003, is a robust and efficient solution for stacking and organizing printed materials. With a format of 500 x 340 mm, this stacker is currently in production and located in the United States. The delivery terms are FCA (Free Carrier), meaning the seller delivers the goods, cleared for export, to the carrier appointed by the buyer. The machine is in good condition, ensuring reliable performance for various stacking tasks in printing and finishing applications. Format: 500 x 340 mm Gsdpfx Aevmnfpog Tsil Equipment: Good condition without any damage

Condition: used, overall weight: 221 kg, total length: 400 mm, total width: 400 mm, total height: 540 mm, Cross tooling column with Gressel Mounting holes 4 Pitch fixing holes 320 mm Length 400 mm Width 400 mm Height 540 mm Weight 221 kg Giedex Ttzzepfx Ag Tsl If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: good (used), Year of construction: 1996, functionality: fully functional, Diameter x width: 750 x 1,500 mm max. operating pressure 300 bar Cutting force 60 kN Weight: approx. 2,800 kg 76 chisel Godsqnvtzspfx Ag Teil

Condition: used, Cross table with stepper motor drive Precision positioning systems UHL Cross table UHL type KT5-NSOC Series no. 0008002 Table size: 145 x 145 mm Table opening: 75 x 75 mm Height: 51 mm Travel: 50 mm per axis Gsdpfxeflrtps Ag Tjil Straightness / flatness: 5 μm - Drive per axis via 2-phase hybrid stepper motor, type ZSS 33.200.1,2 - Manual adjustment Dimensions (cross table) L x W x H: 265 x 220 x 51 mm Weight: 3.5 kg Very good condition

Condition: used, Year of construction: 2009, Price: On request Undercutting crosscut saw Weinig Dimter Opticut S 90 Serial no. 4421.24 Built in 2009 Automatic feed system Up to 60 m/min Three-phase current 400V / 50Hz Control voltage 24VAC / 230VDC Power 20kW Rated current 40A Fuse 50A Dimensions machine 2000x1400x1650 mm (LxWxH) Dimensions input table 7450x2100x1100 mm (LxWxH) Dimensions output table 4900x2400x1400 mm (LxWxH) Dimensions total setup 16300x2700x1950 mm (LxWxH) Including fencing and waste discharge belt  Available immediately - Year: 2009 - Documentation available: No - CE certificate present: No - Serial number: 4421.24 Financial information Giedpfowhlvgex Ag Tsl VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Year of construction: 1979, Model making milling machine, universal model milling machine, milling machine, universal milling machine, tool milling machine, drilling and milling machine, model making milling machine Gijdpfx Asnzpx Reg Tel -Manufacturer: Zimmermann, universal milling machine type FZ 1 with extensive accessories -rotating cross table: 490 x 400 mm -Travel: X/Y/Z 320/385/430 mm -Spindle holder: SK30 -Drive: 1.1 kW -Speed: 560 to 14000 rpm, 8-stage -Accessories: incl. see photos -Dimensions: 1000/680/H1970 mm -Weight: 477 kg

Condition: good (used), Year of construction: 2011, input frequency: 50 Hz, control voltage: 24 V, Automatic cross strapping machine Gjdpfx Ajwk Nynog Tjil Manufacturer: Mosca Model: SONIXS-TRP Year of manufacture: 2011 Condition: good, see pictures

Condition: excellent (used), SCM internships in excellent condition Gedpfot Hkq Rex Ag Tsil

Condition: new, Year of construction: 2026, Crosscut and Mitre Circular Saws Type ZS 200NF Crosscut and mitre circular saw with a maximum cutting height of 200 mm Robust grey cast iron construction Precise ball bushing guidance of the tool carriage on hardened and ground steel shafts Manual saw feed Quick mitre adjustment up to 65° horizontally and 60° vertically Adjustable fixed stops Lower saw blade guard connectable to extraction system Machine mounted on mobile machine base with 1.5 m long roller conveyors on both sides (left and right) Left side equipped with scale and stop slider Technical Data Motor 400 V / 5.0 kW Speed 2800 rpm Gsdjw Hl Aqspfx Ag Tsil Cutting length 420 mm (at 90°) Cutting height 200 mm (at 90°) Mitre range horizontal 45°- 90°- 25° Mitre range vertical 60°- 90°- 30° Saw blade Ø 520 mm (not included as standard) Extraction port 100 mm Weight 490 kg Location: In stock at 54634 Bitburg - Immediately available - On request, we are happy to offer the saw blade as well.

Year of construction: 2016, condition: used, Transnorm roller conveyor ejector GF 4510-1120-1000 RA1854 Make: Transnorm Roller width (RB): 1030 mm, Steel rolls Nominal/outer width (NB): 1050 mm Rolls diameter: 50 mm length: 3715mm Overall height frame: 250 ejector angle: 30° in both sides 7 rows ejector individually controllable Motor MOVI-Mot 300-500V 1,75kW Conveyor speed: freely adjustable with frequency converter Scope of delivery: with supports (please enquire if required) Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Gijdpfx Aek Abhheg Tsl Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, Year of construction: 2001, Wood dimensions to be processed: Input lengths min/max 500 - 6500 mm Full optimization up to max. 1500 mm Input widths min/max 40 - 300 mm Input thicknesses min/max 15 - 120 mm Wood cross-sections max. 300 x 40 mm max. 200 x 120 mm Fixed lengths after sawing min. 510 - 2800 mm Special application: Cutting blocks, length min/max. 100 - 200 mm (Caution: Multiple block lengths at the sorting line; blocks are transported to the end of the sorting line and fall into the customer's grid box). Cutting/cutting tolerance +/- 0.8 - 1.5 mm (for wood types with minimal resin content and an even surface. Tolerance up to 1 m fixed length, max. tolerance for longer pieces up to 2.5 m). Thickness tolerance +/- 3 mm. Curvature of the wood in all directions: max. 10 mm per meter in length. Wood types: soft or hardwood. System performance: Feed speed, continuously adjustable up to max. 230 m/cutting cycle 0.6 - 1. To obtain the practical output per day, an effectiveness factor dependent on the customer's production conditions must be calculated. Infeed and saw height: 900 mm (placed on customer's platform, saw requires concrete base). Sorting working height. 2000 mm Connection values: Total electrical connection value approx. 18 kW Operating voltage 380 Volt / 50 Hz Voltage fluctuations max. 5% Air consumption approx. 1200 NL/operating pressure approx. 8 bar Extraction speed approx. 30 m/nd Color pebble gray RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Item 1 Infeed and marking station with 1 side support table, adjustable 1 table as stop edge Item 2 Support roller without drive, front side in front of sheet metal table for easier feeding Item 3 Length measuring station with built-in fluorescence camera for detecting error markings Item 4 Automatic width measurement, contactless Item 5 OptiCut 304 optimizing cross-cut saw - right-hand version with built-in waste chute including equipment package for large wood cross-sections Graphic input terminal (16 x 40 characters, Numeric keypad) with software package for optimization and system control. Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Item 6: Outfeed conveyor as sorting station with drive unit, length 7500 m Item 7: 2 ejectors mounted on the outfeed conveyor Gsdpfx Ajw Sy T Hog Tjil Storage location: Nattheim

Condition: good (used), Cross support, cross support, cross table, cross-sliding table -Manufacturer: Kunzmann, top head from milling machine type UFV 600 -Dimensions: 530/420/H730 mm -Weight: 80 kg Gsdsg Dg Rpepfx Ag Tjil

Condition: used, Year of construction: 1999, ❗Honing Machine / Cross-Honing Machine Sunnen Eclipse EC-3500-CGM-27 ❗ Year of manufacture: 1999 Machine No.: 3X1-1926 Condition: Used, untested Delivery terms: Free loaded on truck – unpacked Location: 82216 Maisach Availability: Immediate – upon agreement Payment terms: Advance payment – by bank transfer Internal no.: PHY1 Technical specifications: Manual stroke diameter range: 1.5 – 165 mm Automatic stroke diameter range: 1.5 – 102 mm Stroke length range: 6.0 – 170 mm Spindle speeds: 200 – 3000 rpm Stroke rates: 60 – 500 strokes/min Spindle motor power: 4.1 kW Stroke motor power: 1.1 kW Compressed air requirement: 5.5 bar 400 V / 50 Hz Spindle bearings renewed in 2015 Frequency converter replaced in 2024 Spindle motor fan replaced in 2025 Further technical data – see PDF attachment Notes: Stop fingers missing (see photo) Operating hour counter defective Tool type selector switch defective Light curtain defective (bypassed in the control cabinet) Despite the above-mentioned defects, the machine was in regular operation at a specialist company. Scope of delivery: Available documentation No additional accessories Dimensions & weight: Giedpfxjxv Dmqj Ag Tjl Installation dimensions (L x W x H) approx.: 1600 x 1200 x 1900 mm Weight approx.: 900 kg If you have any questions or wish to arrange a viewing, please do not hesitate to contact us. ⚠️Also take a look at our other listings.⚠️ Additional notes: We expressly recommend collection by direct shipment (haulage company). The item is sold without any warranty of any kind. Technical specifications provided without obligation. Subject to prior sale. ❗Sale exclusively to business customers❗

Condition: excellent (used), Your contact persons in our company: Mr.: Andre Evering Mr.: Mario Klöver Mr.: Falk Deutsch Technical data of the pallet rack traverse: Racking system: META (Thyssen) Included in delivery are: 01x pallet rack traverse, used Material color: orange type of truss: HN 100|20 box profile: 100 x 50 mm agraffe: 3 HK (hooks) clear width: 2.700 mm max. load per truss pair Gsdjiimtqjpfx Ag Teil 2.100 kg, with evenly distributed load 02x safety pins, used execution: compl. galvanized To secure the longitudinal beams against unintentional lifting out General information about the article: This article is offered for pickup only. Any additional transport or shipment of this or a shipment of this article is associated with additional costs, which can be requested separately depending on the delivery location or scope of delivery can be requested from us. Our services at a glance: (prices on request) Assembly, erection our general assembly conditions are to be observed Rack inspection Rack inspection according to DIN EN 15635 executed according to the requirements of BGR 234 visual inspection for all racking systems Delivery with our own fleet (without unloading)

Year of construction: 2014, condition: used, Transnorm roller conveyor ejector GF 2500-700-685 RA2212 Gijdpfjrg Nzuox Ag Tel Make: Transnorm Roller width (RB): 685 mm, Steel rolls Nominal/outer width (NB): 700 mm Rolls diameter: 50 mm length: 1800 mm, 2500 mm or 3180 mm (double) Overall height frame: 250 ejector angle: 45°, left 3 rows ejector pneumatic controllable Motor MOVI-Mot 300-500V 1,75kW Conveyor speed: freely adjustable with frequency converter Scope of delivery: without supports (please enquire if required) Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, Year of construction: 2001, Abrasive belt length 1st unit: 2,150 mm Max. working width: 1,300 mm Number of belts: 3 Belt 1st unit: cross belt Design 1st unit: cross belt Sanding pad 1st unit: electronic segmented pad Abrasive belt width 1st unit: 150 x 4,800 mm Drive 1st unit: kW 2nd unit: longitudinal roller Design 2nd unit: steel calibration roller Abrasive belt length 2nd unit: 2,150 mm Gsdpfsxzi S Nex Ag Tsil Abrasive belt width 2nd unit: 1,350 mm Abrasive belt speed 2nd unit: 18 m/sec 3rd unit: pad unit Design 3rd roller: electronic segmented pressure beam SDS system Sanding pad 3rd unit: electronic segmented, 32 mm width Abrasive belt length 3rd unit: 2,150 mm Abrasive belt width 3rd unit: 1,350 mm Suitable for lacquer sanding: yes Belt air blast: yes Vacuum conveyor: yes Feed speed, fixed: stepless 5 – 15 m/min Control: screen control Electrical/pneumatic belt oscillation: electrical Infeed height: variable (lower table moves) Table height adjustment: electric motor Table height display: digital Working height / feed table height: 880 mm Location: Supplier

Condition: good (used), Cross table controlled, cross table NC, coordinate table, LM Guide Actuator, linear drive, coordinate table, precision table linear guide, CNC cross table Gjdpfjqgi Ihex Ag Tjil -Cross table: with linear drives THK LM Guide Actuator KR -Travel: x= 310 mm / y= 500 mm / z= 125 mm -Spindle pitch: 10 mm -Individual components: see photos -Dimensions: 750/550/H445 mm -Weight: 35 kg

Condition: good (used), Technical data for the pallet rack traverse: Rack system: Stow Type: Pal Rack NS In the trusses are from the top, bottom & front view each 2 holes with a Ø of approx. 16 mm! These are used for diagonal bracing! Included in delivery are: 01x pallet rack traverse, used Material color: orange U-profile : 150 x 50 x 3,00 mm execution: head traverse agraffe: 4 HK (hooks) clear width: approx. 1.400 mm Gsdpelgzqcefx Ag Tjil 02x safety pins, used execution: compl. galvanized To secure the longitudinal beams against unintentional lifting out General information about the article: This article is offered for pickup only. Any additional transport or shipment of this or a shipment of this article is associated with additional costs, which can be requested separately depending on the delivery location or scope of delivery can be requested from us.

Year of construction: 2014, condition: used, Transnorm roller conveyor ejector GF 2500-700-685 RA2212 Make: Transnorm Roller width (RB): 685 mm, Steel rolls Gijdsrg Nzxepfx Ag Tjl Nominal/outer width (NB): 700 mm Rolls diameter: 50 mm length: 1800 mm, 2500 mm or 3180 mm (double) Overall height frame: 250 ejector angle: 45°, left 3 rows ejector pneumatic controllable Motor MOVI-Mot 300-500V 1,75kW Conveyor speed: freely adjustable with frequency converter Scope of delivery: without supports (please enquire if required) Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: good (used), Your contact persons in our company: Mr: Andre Evering Mr: Mario Klöver Mr: Simon Blank Here we offer you a used pallet rack cross beam of manufacturer Vogelsang for purchase. Technical data of the pallet rack cross beam: Manufacturer: Vogelsang Type: NS Included in the scope of delivery: 01x pallet rack cross beam, second-hand Material colour: orange box profile: 110 x 50 mm clear width: 2.700 mm max. load per pair of cross beams Gisdpfsfq Du Dox Ag Tjl 2,700 kg, with equally distributed load 02x locking pins, used Finish: completely galvanized For securing the longitudinal beams against inadvertent lifting out Our services at a glance: (Prices on request) Mounting, construction our general assembly conditions are to be observed Shelf inspection Shelf inspection according to DIN EN 15635 carried out in accordance with the Requirements of BGR 234 visual inspection for all shelf systems Delivery with our own vehicle fleet (without unloading)

Year of construction: 2014, condition: used, Transnorm roller conveyor ejector GF 2500-700-685 RA2212 Make: Transnorm Roller width (RB): 685 mm, Steel rolls Nominal/outer width (NB): 700 mm Rolls diameter: 50 mm length: 1800 mm, 2500 mm or 3180 mm (double) Overall height frame: 250 ejector angle: 45°, left 3 rows ejector pneumatic controllable Motor MOVI-Mot 300-500V 1,75kW Conveyor speed: freely adjustable with frequency converter Giodporg Nzqjfx Ag Tol Scope of delivery: without supports (please enquire if required) Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics