Used Cross Cut Optimization for sale (20,100)

Condition: excellent (used), Year of construction: 2005, Weinig Dimter OptiCut S 90 optimizer with 2 ejectors – after technical review – German production – year of manufacture 2005 TECHNICAL PARAMETERS: max. length of cut material 4500 mm max. width 360mm max. height 160mm automatic length measurement optimization in 4 quality classes total power 13 kW blade motor power 7. 5 kW pneumatic side and top pressure disc diameter max. 500mm OptiCom Assist control receiving conveyor 5600 mm two ejectors total length 13 m component marking printer cutting accuracy +/- 0.5 mm transport dimensions (length / width / height) 600 / 240 / 190 cm weight ~ 1800 kg Dcedpji Apgmefx Adtok

Condition: good (used), Year of construction: 1998, Optimizer GreCon Dimter OPTICUT 204 R - year of production 1998 - full optimization - cutting to a dash - width measurement - possibility of cutting aluminum TECHNICAL PARAMETERS: Dcjdpfx Ajh Hfknodtjk - max. cutting length 4,000 mm - min. element 200 mm - max. cutting height 100 mm - max. cutting width 260 mm - disc diameter 500 mm - engine power 9 kW - feed speed max. 160 m / min - acceleration 2 m / s2 - optimization in terms of length and value - pneumatic pressure of the material - three ejectors - dump tables - Rotary table - total length of 2000 cm Transport dimensions: - length 1300 cm - width 245 cm - height 220 cm - weight 3500 kg

Condition: new, Number of milling spindles 2 St. fence 1 ja workpiece ja Stegherr Cross rung milling machine TYPE KSF-mini including standard stop with 2 sliding stops, without tools With the KSF-mini, all of those that occur in practice can be used Crossbar connections can be made quickly and precisely. The Precise execution is achieved by having the workpiece in one Clamping is machined on three sides. The tool is driven by two three-phase motors; the tension of the Workpieces pneumatically. The profile cutter is designed for the web width. The saw blades that... If you carry out flattening, spacer rings are used to match the dimensions of the Profile milling cutter adjustable. The swivel device is free of play. The machine is designed for a maximum workpiece cross section of 56 x 46mm. Voltage Europe: 400V(+/-10%)/3Ph/50Hz, USA: 440V(+/-10%)/3Ph/60Hz Other voltages on request. Operating instructions in German or English. Table base EUR 1.070.00 Foot switch EUR 900.00 Adjustment optics EUR 130.00 Profile milling cutter in HM-Wepla version, available for selection: Ø 5,7,9,11,13 mm. Price per piece EUR 650.00 1 set of replacement insert knives for profile milling cutters (=10 pieces) EUR 190.00 HM saw blade, price EUR 170.00 per piece (For a web of e.g. 10 mm, 3 saw blades are required) Dsdpfxoyrtzqe Adtjck Setting the machine to the tools provided by the customer, price EUR 700.00 per individual tool Packaging in a crate (suitable for land transport) EUR 650.00 Packaging shrink-wrapped on a pallet (only within Europe, not for air freight) EUR 340.00 Pricing ex works, unpacked, uninsured, for delivery within Germany plus the VAT valid at the time of delivery. (all technical information according to the manufacturer, without guarantee!)

Condition: good (used), Year of construction: 2006, I sell the automatic pneumatic optimising end cutting saw PAUL 11 MKL MAXI 5 Premium Year 2006 Dedpozraaxefx Adtsck Input table automatic (throughfeed system) Outut table automatic 6 pcs. kickers on left outfeed table Optimising with mistakes deffect reading and automatic cutting sequence modes. Available immediately. CE version. Documentation included.

Condition: like new (used), High volume production of small components including stair wedges, stair glue blocks, corner blocks for chairs, filler pieces, and more. Key Features: Dedezd Uxmepfx Adtsck Self centring grippers and centreline cutting with angles of +/-60 degrees. Hopper fed with a standard length capacity of 1350mm - components are collected in box underneath. Produce up to 800 pieces per hour. Small footprint to maximise floor space. Condition - As New [only been used for showroom demonstrations.] 1350mm x 200mm x 80mm Capacity Cutting thickness from 10mm to 80mm Cutting width from 10mm to 200mm 3 seconds per operation - feeding, cutting & drilling = 9 seconds Up to 60m/min advancement speed 4kW saw motor +/- 60 degree rotation - mechanical adjustment Completely enclosed interlock saw cabin Outfeed conveyor belt

Condition: good (used), Thickness gauge, coating thickness gauge, Cross Hatch Cutter -Manufacturer: Elcometer, cross-cut device with case -Type: Elcometer 107 -Material: stainless steel / aluminum -Accessories: see photos -Dimensions: 300/270/H75mm Dcjdjr H Nlhopfx Adtjk -Weight: 1.1 kg

Condition: reconditioned (used), Number of milling spindles 2 St. fence ja ja /nein workpiece ja STEGHERR Cross-bar Milling Machine, Type KSF-mini ----- Specialized milling machine for the efficient production of intersecting muntin bar joints. The KSF-mini muntin bar milling machine embodies STEGHERR's extensive experience in manufacturing specialized milling equipment for intersecting muntin joints. The KSF-mini enables the rapid and precise production of all standard intersecting muntin joints encountered in practice. Muntin bars that have already been profiled can also be processed on the KSF-mini. Precise milling is achieved because the workpiece is machined on three sides in a single clamping operation. The tools are driven by two three-phase motors; workpiece clamping is pneumatic. The profile cutter is designed to match the web width. The saw blades that perform the lap-joint cut can be adjusted to the profile cutter's dimensions using spacer rings. Dcedjzip Nwepfx Adtjk The machine is designed for a maximum workpiece cross-section of 56 x 46 mm. - Motor: 2.2 kW, 380 V, 50 Hz - Pneumatic pressure: 6 bar Includes: ----- - Machine stand - Foot pedal control - NEW ORIGINAL stop rail with scale and sliding stop featuring an optical setting aid, as shown in the photos. Tools as shown in the photos: 1 Profile cutter 3 Saw blades (corresponding to a web width of 10 mm) Footprint approx. L x W x H: 1,330 x 570 x 1,430 mm Weight: approx. 150 kg ----- (All technical specifications provided by the manufacturer; no liability assumed!)

Condition: used, Year of construction: 2003, The machine is in perfect working condition. Dsdpfjgrn Emjx Adtsck

Condition: good (used), Year of construction: 2006, I sell the automatic pneumatic end cutting saw Weinig Grecon Dimter Opticut 200 Elite Year 2006 Motor power 7,5kW Input table automatic feeding 4,10m (throughfeed system) Outut table automatic 6 pcs. kickers on right outfeed table Dodpfx Ajxtxi Ijdtsck Optimising with mistakes deffect reading and automatic cutting sequence modes. Available immediately. CE version. Documentation included.

Condition: used, Year of construction: 2006, operating hours: 100 h, functionality: fully functional, Profi Industrial Cutting System (Longitudinal/Cross) – Grossmann – ONLY 100 operating hours! Description: For sale is a high-precision, automated longitudinal and cross-cutting machine from quality manufacturer Grossmann Maschinenbau. The system has a total runtime of no more than 100 operating hours. It is therefore in an almost mint technical condition and shows hardly any signs of wear on the mechanical components. Originally designed for cutting chip mats, this machine’s robust construction and versatile PLC control make it suitable for a wide range of materials (e.g. rubber, cork, fleece, composites, films, textiles, etc.). Technical highlights & features: Condition: Nearly new (max. 100 operating hours). Format: Maximum cut length 2,500 mm x maximum working width 1,200 mm. Complete line: Includes professional unwinder and winder for fully automatic material flow from roll to roll or roll to format. PLC control: Professionally programmed, with a choice between manual and automatic operation. Material handling: Automatic gripper feed positions material precisely in the end position, with integrated edge removal system for perfectly clean edges. Operation: Intuitive control via display, foot switch, and optical/acoustic production completion indicators (traffic light/horn). Precision: Integrated laser for exact material alignment. Dsdpeylxmfsfx Adtsck Safety: Fully enclosed design and modern safety monitoring. Versatility: This machine is a true all-rounder for any rolled material that needs to be cut to precise sheet sizes or strips. Its stable construction with a high-quality aluminum profile system ensures maximum rigidity. Complete documentation available, including process protocol, wiring diagrams, and technical drawings. The machine can be inspected and tested under power by appointment. For exact technical details and questions about fields of application, please feel free to contact me personally. Contact: Phone: 05427 9423 20

Condition: good (used), Year of construction: 2012, I sell the automatic optimising end cutting saw Salvador Superpush 200, year 2012. Input table automatic feeding 5,10m (pusher system) Outut table 3,00m Total length: 9,00m Optimising with automatic cutting sequence modes. Dodpfxsyi Suwo Adtjck Available immediately. CE version. Documentation included.

Condition: good (used), Year of construction: 2005, I sell the automatic pneumatic end cutting saw Weinig Grecon Dimter Opticut 200 Elite Year 2005 Motor power 7,5kW Input table automatic feeding 5,10m (throughfeed system) Outut table automatic 6 pcs. kickers on left outfeed table Dodoxtxg Hspfx Adteck Optimising with mistakes deffect reading and automatic cutting sequence modes. Available immediately. CE version. Documentation included.

Condition: used, Year of construction: 2021, UK's Best Selling Automatic Crosscut Saw Built to meet the precise standards of fine joinery while embodying the robust quality of a sawmill, the globally acclaimed TR500 saw unit boasts a distinguished history of over 400 installations in the UK and over 50 years of industry use. A key component within the TR platform, the TR500 stands out with its ever-present 7.5kW saw motor - a consistent feature across the entire Stromab range. Its variable speed cutting cycle allows the precise cutting of softwoods or hardwoods, accommodating dimensions of up to 135mm in height or 360mm in width, all managed by a single top clamping unit. Infeed: The industry standard rack and pinion system featured through the Stromab range allows timber lengths of up to 14m and up to 90kg to be push fed without additional rollers. Featuring a table incline of 8 degrees, automatic lifting pusher system and a positioning accuracy of 0.4mm, the Stromab Matrix powers through your repetitive and bulk cutting requirements. Controller: Harnessing the power of an ELCO Top 12 colour touch screen, cutting lists are simple to programme using the innovative optimisation methods: BASE with board sequence, max length, or sequence. OPTI with base features and volume, minimum waste or priority. Alternatively, use our 'Design2Saw' software to pre-optimise files for the highest yield savings, loaded quickly via USB to reduce operator programming time. Specification Dcsdpfx Aezd Uqcjdtsk Saw Unit: 7.5kw saw motor 500mm diameter saw blade 135mm x 120mm cutting height 360mm x 55mm cutting width Infeed & Outfeed: 90m/min positioning speed 0.4mm positioning accuracy 8 degree incline on table Servo driven rack & pinion 1m outfeed table as standard Automatic lifting of pusher arm Controller Elco TOP12 12" industrial touch screen PC 3 optimisation criteria - longest length, sequence & board sequence Fitted with the following options - 6000 mm in feed capacity Pneumatic lifting of pusher 10 hp saw motor Ø500 mm saw blade Opti version with full optimisation and board length reading Defect reading camera ( chalk mark reading )

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Dedpezp H R Esfx Adteck Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: used, Year of construction: 2015, Swift Cut 3000 W/T Plasma Cutting Machine, 3000mm x 1500mm Cuttting Bed, Hypertherm Powermax 125 Power Source. S/No. 4500318 (2015). Country of Origin: United Kingdom Please Note: Collection from 6th – 20th October 2026, Site will be closed from 10th September – 5th October 2026 Location: These lots are located in Cardiff, Wales, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. Dcjdpfx Aezn Uuisdtok

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, Equipment: CE marking, cooling unit, documentation/manual, Fiber Laser Cutting System CUT LITE PENTA, Model LME 3015 Year of manufacture: 2021, CE certified Dedpfxsznk Dtj Adtjck Excellent condition. Cutting dimensions: 3000 x 1500 mm Laser source: IPG YLS 6000 W

Condition: good (used), Eurotecnica 425 CUT Perfect Binder This machine is in perfect technical and visual condition and was used as a backup for the BQ-470 binder. Machine features: – automatic jaw clamping – disc milling with additional scoring units – infeed jogging device – side gluing – control panel – fume extraction from the gluing unit – trim extraction + external vacuum – automatic cover clamping 230V power supply Dcsdpfx Adozlaa Sotok The kit includes glue to start with.

Condition: as good as new (ex-display), Swift-Cut CNC plasma cutting machine, type 1250Pro WT with water table and marking unit Cutting area 1250 x 1250 mm Dodey Sxvhspfx Adteck with ESAB power source Technical data: - Cutting area for sheet metal formats up to 1250 x 1250 mm - Table dimensions 1980 mm x 1840 mm - Table weight 800 kg - Table capacity 160 l - Height 1500 mm - Z-axis travel 130 mm - Max. load capacity 200 kg/m² - Traverse speed 20 m/min - Guides: Hybrid servo motors and double-sealed linear bearings on all axes. - Closed ball screw-driven Z-axis. Double-driven Y-axis. - Bridge clearance 150 mm - Max. material thickness 25 mm - Max. cutting capability for square tubes 100 mm - Required compressed air pressure 7-7.5 bar - Flow rate 300 LPM - Linear positioning accuracy 0.5 mm/m - Repeatability 0.4 mm/m - Measurement of roundness tolerance 0.3 mm/m FURTHER DETAILS AVAILABLE UPON REQUEST.

Condition: good (used), functionality: fully functional, control type: manual, degree of automation: semi-automatic, actuation type: hydraulic, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, back gauge adjustment: motor-driven, back gauge: 1,000 mm, Equipment: angle stop, documentation/manual, emergency stop, foot remote control, The cutting tool can be used with 4 different attachments, with 2 currently in use. Manufactured in Germany. Djdpfszmyyzsx Adtsck

Condition: good (used), Uchida Aero Cut One Creaser, Slitter, and Cutter The machine is fully operational and ready for production. Description: The AeroCut One cuts, perforates, and creases sheets in a single pass. Only one person is needed to operate the device, significantly improving work efficiency and, consequently, reducing costs. The device is programmed using an intuitive touchscreen control panel. Cutting, creasing, perforating Maximum paper size – 370 x 520 mm Min. paper capacity – 55 x 45 mm Maximum grammage – 400 g/m² Speed ​​– 11,130 business cards/h Paper types – offset, coated paper, varnished Feed – belt with adjustable vacuum Creasing – strip-type Memory – 263 programs + 150 user-defined Touchscreen programming PC connectivity Double-feed detection Weight: 240 kg Dcjdpfx Ajziyrpsdtek Power supply: 230 V Made in Japan.

Condition: good (used), Year of construction: 2007, functionality: fully functional, cutting length (max.): 6,000 mm, saw blade diameter: 500 mm, saw blade speed: 2,800 rpm, input voltage: 400 V, rotational speed (max.): 2,800 rpm, saw band length: 500 mm, main saw diameter: 500 mm, saw blade length: 6,000 mm, Double automatic aluminum saw with 500 mm blades. Cuts materials up to 6000 mm in length. Can automatically cut an entire profile into smaller pieces. Dcedpfx Aex U Df Hsdtjk Length, cutting angle, and material thickness are electronically adjusted on the machine. The saw system is in perfect working order. For sale due to production shutdown. We are happy to assist with loading the machine onto the buyer's truck.

Year of construction: 1970, condition: used, Cut Tape BRENTA torso 1200 Dcodpfscudizjx Adtek Location Gorzow Wielkopolski. Conditions of delivery Cost of delivery Client cover startup type negotiated Description Comments Vertical band saw blade stylitowane carbide wheel diameter 1200 mm, adjustable mechanical feed, feed regulation smoothly on the tape and the wheels flat, cast iron, no need to anchor. Important machine has the ability to cut diameters up to 330 mm, new electrics, a complete ready to go, belt width 200 mm stylit, after pouring rubber on the wheels do not need to regenerate.

Condition: good (used), Year of construction: 2017, functionality: fully functional, working range: 3,050 mm, travel distance X-axis: 3,050 mm, travel distance Y-axis: 1,525 mm, travel distance Z-axis: 220 mm, positioning accuracy: 0.015 mm, input voltage: 400 V, table length: 3,050 mm, operating speed: 250 mm/s, table width: 1,525 mm, pressure: 4,137 bar, positioning speed: 15 m/min, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, table height: 840 mm, operating pressure: 4,137 bar, input current: 77 A, total height: 1,300 mm, total length: 4,210 mm, total width: 2,130 mm, water pressure: 2.8 bar, pump pressure: 4,137 bar, overall weight: 3,850 kg, working length: 3,050 mm, power: 37 kW (50.31 HP), Equipment: safety light barrier, 2017 Swiftcut Swift-Jet CNC Waterjet Cutting Machine – Under 900 Hours Use High-Precision CNC Waterjet Profile Cutter – Low Hours, Good Condition – Now Available at Used Machine Tools Ireland Ltd 🔍 Overview: We are offering this 2017 Swiftcut Swift-Jet Waterjet Cutting Machine, a top-tier solution for high-precision, cold-cutting of a wide range of materials including metal, stone, plastic, glass, and composites. With less than 900 operational hours, this machine is in very good condition and ideal for any business seeking reliable, accurate, and versatile cutting performance. 🛠️ Machine Specifications: Brand: Swiftcut Model: Swift-Jet Year of Manufacture: 2017 Technology: CNC Waterjet Profile Cutting Cutting Area: 3000 x 1500mm Hours Used: Less than 900 hours Pump Type: High-pressure waterjet pump Cutting Method: Abrasive and pure water capability Software: Swiftcut Control Software (user-friendly, intuitive interface) Table Dimensions: 3000 x 1500mm Max Sheet Size: 3050 x 1525mm (10' x 5') Max Traverse Speed: 15m.min Max Z Axis Clearance: 220mm Positional Accuracy: 0.015mm Tank Depth: 840mm Max Pressure: 60,000psi(4137bar) Continuous Pressure: 60,000psi Min. Piercing Pressure: 20,000psi Max Output Flow: 3.8l/min Max Orifice Size: 0.36mm Min Orifice Size: 0.13mm Cutting Water Infeed: 7.6l/min Water Pressure Infeed: 2.8bar Pump Voltage: 400V/77A Pump Power: 37kW/50HP Machine Voltage: 1ph/16A Water Treatment Voltage: 1ph/10A Garnet Hopper Voltage: 1ph/10A Machine Dimensions: 4210 x 2130 x 1740mm Pump Dimensions: 1850 x 920 x 1300mm Machine Weight: 2400kg(empty) Pump Weight: 1450kg 🌟 Key Features: Cold-cutting process – no heat-affected zones, preserving material integrity Precise and clean cuts on a variety of materials and thicknesses Ideal for metal fabrication, signage, engineering, prototyping, and more Compact footprint, easy installation, and low maintenance Exceptional build quality from a trusted UK manufacturer 🔧 Applications: Perfect for cutting: Mild Steel, Stainless Steel, Aluminium Brass, Copper Stone, Granite, Marble Plastic, Acrylic Glass, Rubber, Composite Materials ✅ Why Choose This Swift-Jet? Very low hours – lightly used and well maintained Excellent condition – ready to work immediately Cost-effective alternative to brand new equipment Dcjdpfswb D S Hjx Adtjk Supported by Swiftcut's strong reputation for service and performance Take advantage of this rare opportunity to own a high-spec waterjet cutting system with low hours – ideal for precision fabrication. Act quickly – this unit won’t last long! Used waterjet cutting machine Ireland, Swiftcut Swift-Jet for sale, CNC waterjet profile cutter, low hours waterjet machine, 2017 Swift-Jet waterjet, metal and stone cutting machine, abrasive waterjet cutter, used CNC cutting machines Ireland, high-precision waterjet cutter, used fabrication equipment for sale Notes: *Specifications are given in good faith but not guaranteed*

Condition: new, Year of construction: 2026, functionality: fully functional, power: 7.5 kW (10.20 HP), cutting height (max.): 200 mm, saw blade diameter: 600 mm, working height: 900 mm, We are selling 1 x CrossCut600. Cutting dimensions: 50x765 - 140x605 - 180x340 - 200x200 mm Maximum cutting height: 200 mm Dcedjfl Imaspfx Adtok Saw blade: Ø 600 mm Working height: 850 mm Dust extraction port: bottom Ø 120 mm, top Ø 100 mm - Infinitely adjustable, pneumatic feed system - Hydraulic brake cylinder for consistent feed speed - Pneumatically controlled workpiece clamping device - Cutting initiation via 2-hand control, with safety guard - Roller conveyors and stop systems available upon request.

Condition: new, Year of construction: 2026, functionality: fully functional, power: 11 kW (14.96 HP), cutting height (max.): 260 mm, saw blade diameter: 800 mm, working height: 880 mm, We are selling 1 x CrossCut 1.000 Dcedpfxsrfudrj Adtek Cutting dimensions: 60x940 - 140x820mm - 180x720 - 220x520 - 240x340 Maximum cutting height: 260mm Saw blade: Ø 700mm Working height: 880mm Dust extraction port at the bottom and top: Ø 120mm - Infinitely adjustable, pneumatic cutting feed - Hydraulic brake cylinder for consistent stroke speed - Pneumatically controlled workpiece clamping device - Cutting activation via 2-hand control, with protective shield - Roller conveyors and stop systems available upon request