Used Double Column Presse for sale (25,380)

Condition: used, Technical details: pressure: 20 t slide stroke: 6 - 60 mm throat: 176 mm ram adjustment: 55 mm no. of strokes: 155 Hub/min distance table/ram: 270 mm passage width: 470 mm Table dimensions: 300 x 450 mm passage opening in table: 90 mm Dkedpju Nfliefx Ak Aew surface area of ram: 130 x 248 mm inclination: 28 ° mortise hole in ram: 25 x 65 mm table height over floor: 775 mm air pressure - required: 5,5 - 6 bar total power requirement: 3,5 kW weight of the machine ca.: 1,0 t dimension machine approx.LxWxH: 1,3 x 1,1 x 1,95 m High performance press Central lubrication with light barrier (monitored) Linuflex stroke counter (counter) additional steel plate 315 x 400 x 50mm with center hole Ø 63mm *

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW Dodpfsk S Dt Tox Ak Aokw ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: used, Technical details: pressure: 80 t distance between columns: 880 mm dayligth: 200 mm Table dimensions: 880x300 mm height over floor: 1000 mm distance between columns: 800 mm total power requirement: ca. 12 kW machine weight ab.: 2855 kg space requirements of the machine approx.: T:1,4xB:1,65xH:1,9 m Embossing - Hot Embossing application area: - for example: for foils, plastics, paper, hardboard materials etc. - stamp plate size: 600x310mm equipment: - counter - hydr. tank Accessories: - Mounting plate (600x300x90mm) not heatable. Dkodpfxou Icwts Ak Ajw Sale as is. *

Condition: excellent (used), Year of construction: 2001, Manufacturer: ROVETTA Model: S4-1500 Link Drive Year: 2001 Condition: Used Stock number: 0391 Manufacturer: Rovetta Number of strokes: 4 Ram force: 1500 tons Ram stroke: 763 mm Ram adjustment: 400 mm Daylight (bottom dead center, ram up): 1,200 mm Dkodpoyq Tdiefx Ak Asw Distance between front uprights: 5,700 mm Die bed dimensions: 5,500 x 2,500 mm Ram dimensions: 5,500 x 2,500 mm Moving table height: 600 mm Side window size: 3,400 x 1,900 mm Main motor power: 319 kW Blankholder (total force): 150 tons Blankholder stroke: 250 mm Blankholder working area: 2,000 x 1,200 mm Strokes per minute: 8-24

Condition: used, Year of construction: 1972, pressure 800 t Dkodoyn R Efepfx Ak Ajw distance between columns 3160 mm stroke 1100 mm distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm Dkodpfx Ajynmmrok Asw die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t Dsdsynbc Ispfx Ak Ajkw dimensions of the machine ca. 4,95 x 3,3 x 10,2 m

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm Dksdpoynbdfsfx Ak Asw die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m Dkjdpeynmmxofx Ak Ajw

Condition: good (used), Year of construction: 1989, Power: 1.000 kN Dedpfx Aksd E U Nne Aekw Size of bolster: 800 x 750 mm Distance betw. columns: 900mm Size of ram: 800 x 600mm Daylight: max. 800 mm Stroke: 480 mm Speed: Fast down: 300 mm/s Working: 30 mm/s Fast up: 300 mm/s Electric power total: app. 31 kW Weight: app. 13.000 kg Size of footprint: app. 1,6 x 2,90 x 3,8m (T x B x H) • die cushion, activ, 400kN, stroke 200mm • allowed for 2-hand working • equipped by oil - air chiller • ram guiding by 4 pc. hard chromed Guiding columns

Condition: used, Year of construction: 1989, Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Dksdpfxjuqdi Ue Ak Aew Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton Standard configuration with hydraulic tool clamps on the ram

Condition: used, Double-column hydraulic press SCHÖN Type UTE/B 50 Machine No. 5509 Year of manufacture: 1971 Pressing force: 50 tons Column span: 550 mm Column clearance (side): 150 mm Table size: 480 x 380 mm T-slot width in machine table: 18 mm Table opening: Ø 70 mm Ram area: 490 x 280 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 150 mm Max. installation height: 390 mm Table height above floor: 890 mm Rapid approach speed: approx. 130 mm/sec Working speed: approx. 20 mm/sec Return speed: approx. 130 mm/sec Motor power: 4 kW Power supply: 380 Volt, 50 Hz - Stepless pressing force adjustment - Rapid and working stroke - Pressure or stroke-dependent stroke limitation Dsdpfxov Srfwe Ak Aekw - Adjustable pressure holding time, press time extension 0.5–6 s - Mechanically adjustable hard stop via handwheel on ram - SICK light barrier, Type LVU - Stroke counter - Double column guide on ram Space requirement (L x W x H): 1100 mm x 1050 mm x 2320 mm Weight: approx. 1.5 tons Good condition

Condition: used, Year of construction: 1985, pressure 40 t distance between columns 495 mm stroke 150 mm distance table/ram, max. stroke up, adjustment up 300 mm table surface area 490 x 400 mm hole in the table 50 mm table height over floor 950 mm side window 155 mm Dodpszrptbsfx Ak Ajkw ram surface 150 mm speed down 200 mm/s speed up 200 mm/s working speed 20 mm/s oil volume 115 l power requirement 5,5 kW weight 2,2 t dimensions (WxDxH) 1,35 x 1,1 x 2,2 m with oil-hydraulic drive, upper and lower stroke limitation, mechanical depth stop, two-hand and foot operation

Condition: new, Year of construction: 2019, pressing force: 275 t, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec :2-50 mm/sec. Cylinder hub:900 mm Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø Djdpfxjfxyige Ak Askw :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar

Condition: used, pressure 200 t throat - mm stroke 250 mm Table dimensions 2420 x 840 mm ram surface 1850 x 650 mm dayligth 500 mm ram adjustment 110 mm distance between columns 1900 mm table height 170 mm no. of strokes 25 - 45 Hub/min total power requirement 22 kW dimensions of the machine ca. 2550 x 2370 x 3820 mm weight 30 t - pneumatic clutch - press safety valve, Herion - cam switch, Balluff - chain break monitoring - hydr. overload, Hydac Dedpfx Asgk Rfzsk Ajkw - motor. alide adjustment with digital display - separate control cabinet with safety control ABB - separate two-hand control panel with foot switch - slidable side protective doors - front protection by light barriers vertical + horizontal The machine shown and described above is safe for hand inlays. The machine is also in anorther variant or also can be used as an automatic feeder. Equipment possible according to customer agreement.

Condition: used, pressure 160 t Dkjdpj Agciiofx Ak Asw stroke 8 ... 160 mm no. of strokes (im Leerlauf) 42 Hub/min mould space 560 mm ram adjustment 125 mm weight of the machine ca. 13,9 t

Condition: used, Year of construction: 1996, machine/vehicle number: 14.194, Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Dksdju Saaaspfx Ak Aew Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.

Condition: used, Year of construction: 1987, pressure 800 t stroke 100 mm no. of strokes 45 /min distance between columns 600 mm table surface area 560 x 650 mm capacity of ejector 5 t Dkodpfx Akozl E Sas Ajw ejector stroke 15 mm ram surface 590 x 450 mm power requirement 22,0 kW Weight 17,0 t dimensions (WxDxH) 1,7 x 2,55 x 3,1 m Nominal force travel 1,46 mm With knuckle-joint drive, flywheel brake, hydraulic clutch with 2nd brake, press frame balancing, single ejector in table, self-monitoring control

Condition: used, Year of construction: 2008, Pressure total: 100 ton Daylight: 1.400 mm Table surface area : 1.300 x 1.000 mm Slide area: 1.300 x 1.000 mm Ejector Force: 35 kN max. capacity of swivelling ram plate: 40 kN Die Weight on table max.: 80 kN max. capacity of tilting table: 50 kN Djdpfx Asznn Upek Ajkw Oil volume: 200 l Required power: 10 kW Dimensions L x W x H: 3.95 x 2.3 x 4.5 m Distance between the columns F - B: 1.050 mm Weight of machine approx.: 10 ton

Year of construction: 1984, condition: used, pressure 100 t distance between columns 1000 mm stroke 150 mm table surface area 1000 x 700 mm distance table/ram 500 mm die cushion stroke 180 mm ram surface 1000 x 700 mm ram drills x depth 50 mm no. of strokes 85 Hub/min tool shank hole (depth x diameter) 85 x 50 mm clamping slots 22 DIN 650 form diagonal Dsdpfx Ajfn Apzok Askw number of clamping slots 2 sheet width 400 mm plate length 1000 mm dimensions of the machine ca. 3,0 x 3,0 x 3,0 m weight of the machine ca. 8 t total power requirement 30,2 kW - fine adjustment of stroke - cutting impact damping - oil extraction - 2 cylinders - roller feed, make Dreher, type WAV, control PMS3000 - soundproof cabin - machine was overhauled in 2001 and with new control SIEMENS SIMA-TIC OP17 equipped

Year of construction: 1986, condition: used, pressure 015 t dayligth - mm strokes per minute 200 - 2000 table surface area - mm ram surface 490 x 200 mm sheet width 5 - 50 mm adjustment of stroke 10-30 mm weight 3 t dimensions 1370 x 1200 x 2200 mm Drive 10 kW hole in the table 350 x 100 mm Dkedpsfn Apxofx Ak Aew table width 530 / 210 mm table length 530 / 350 mm

Condition: used, Year of construction: 1979, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS General Information Machine type: electro-hydraulic press Machine weight: approx. 5 t Performance Data Pressure: 63 t Stroke: 315 mm Ram stroke: 200 mm Piston stroke: 200 mm Installation height: max. 450 mm Retraction force: 1.3 t Speeds Dkjdpe Aa Ndyjfx Ak Aow Closing speed: 210 mm/min Return speed: 210 mm/s Table and Ram Table size: 710 × 630 mm Ram clamping surface: 710 × 630 mm Drive Drive power: 15 kW Motor speed: 1,500 rpm Electrical Data Operating voltage: 380 V Control voltage: 220 V Dimensions Overall height above floor: 2,500 mm Overall width: 1,000 mm Depth: 1,600 mm EQUIPMENT Electro-hydraulic press control Fixed safety valve with overload protection Safety interlock Two-hand push button Emergency stop mushroom push button Infinitely adjustable stroke adjustment Infinitely adjustable pressure regulation Fully automatic continuous operation Mechanical, infinitely adjustable fixed stop in the cylinder Handwheel for stop adjustment with display scale Automatic star-delta starter

Condition: used, Year of construction: 1964, Technical details: pressure: 125 t stroke: 28 mm number of strokes: 56-225 Hub / Min distance between columns: 1000 mm ram adjustment: 60 mm distance table/ram: 376 mm Table dimensions: B.950xT:720 mm passage opening in table: 400x130 mm height over floor: 1120 mm ram surface area: 920x540 mm mortise hole in ram: Dm 65 x 120 mm column travel -side: 250 mm total power requirement: 30 kW weight of the machine ca.: 15,5 t dimensions of machine: 3,1x1,34x3,6 m dimensions electric cabinet LxWxH: 0,64x0,22x1,2 m This press is a high-performance press for mass production /series production. - Contains left side a material feed via automatic feed (mechanic) and right side a waste cutter. Feed = 0-200mm, roll width =250mm Partial documentation as a copy available. Dodpfx Aou Nfibsk Ajkw Machine is not functional and is on sale as is! *

Condition: excellent (used), Year of construction: 2002, Schuler Press Type: GMO 2-400-3200-66/203 Year of manufacture: 2002 Djdo Agcaaepfx Ak Aekw Stroke adjustment: 66 - 203 mm Stroke rate per minute: 20 - 100 1/min Ram adjustment: 150 mm Installation height: 700 mm Table area: 3,200 x 1,200 mm Total weight: 72,500 kg Coil handling system, Schuler Automation Coil width: 100 - 1,000 mm Coil thickness: 0.7 - 5.0 mm

Condition: excellent (used), Year of construction: 2001, HELMERDING Press KDH 400/2600/2 Pressing force 4,000 kN Stroke rate 15-60 strokes/min Stroke adjustment 80-250 mm Slide adjustment 175 mm Installation height 550-800 mm Table area 2,500x1,600 mm Slide area 2,500x1,400 mm Pass-through hole in the press table 1,300x800 mm Weight 106,000 kg Lorenz Strip Line EWH 600/150 Strip width 80-600 mm Strip thickness 0.6-6.0 mm Dsdpfxj Agcdae Ak Askw Max. coil weight 7,500 kg