Used Drill Press for sale (16,865)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Hfjdpjy R Nnfefx Ad Rjg Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: like new (used), Year of construction: 2008, functionality: fully functional, travel distance X-axis: 500 mm, travel distance Y-axis: 260 mm, travel distance Z-axis: 160 mm, spindle speed (max.): 7,100 rpm, spindle speed (min.): 50 rpm, total length: 2,000 mm, total height: 2,300 mm, table width: 880 mm, total width: 1,600 mm, table length: 320 mm, spindle nose: SF32 snelwissel, workpiece weight (max.): 300 kg, Equipment: documentation/manual, rotational speed infinitely variable, The machine comes from a university and is therefore in exceptionally good condition (as good as new). If required, it can also be demonstrated in operation at our premises! Hfsdpfx Ajy R Sq Asd Rsg Additional options & accessories: Approx. 15 tool holders Heidenhain TS220 3D probe Original documentation Weight & dimensions: 2,150 kg approx. 2000 x 1600 x 2300 mm (LxWxH)

Condition: excellent (used), Year of construction: 1998, Frame dowel and slot mortising machine from Hofmann HT 200 U with angle adjustment Specialized drilling machine for stair construction, window manufacturing, and universal applications thanks to pneumatic height adjustment. Angled doweling and baluster/rail drilling are easily possible due to the swiveling drilling unit. Motor with pole-change switch, two speeds Motor output 1.5 / 1.8 kW, 1400 / 2800 rpm Motor can be started via a practical handle switch Precision drill chuck with two inserts: 16 mm and M10 thread Table size approx. 1100 x 240 mm Linear laser for precise workpiece positioning Drilling unit can be rotated 65 degrees to the left and right Pneumatic adjustment of working height, allows doweling on two levels without repositioning Desired drilling heights for each drilling level can be set with a handwheel and digital counter; switching between levels is pneumatic and is operated from the front Cross adjustment approx. 320 mm, stepless or in a 12 mm grid Drilling stroke approx. 200 mm 2 pneumatic workpiece clamps, positionable at the front and back of the table 2 swiveling workpiece supports 2 side stops, can also be used as front support Mobile base Extraction port 80 mm 4 used but good drills: 9, 12, 16, 19 mm Few touch-ups on the paint, excellent condition, see original photos A used swiveling slot mortising machine in this condition is very rarely available. CE mark Operating manual Dimensions: approx. 1200 x 1200 x 1200 mm (LxWxH), weight 310 kg. Hjdpeyfta Tefx Ad Rjfg The machine can be demonstrated at our premises by appointment. We only offer machines that are ready for demonstration and available in our warehouse – see “more offers from this supplier.”

Condition: excellent (used), Year of construction: 2006, Dimension: 2650 x 2100 x 2100 mm Clamping Force: 635 KN Working pressure: 206 bar Piston diameter: Ø200 mm Stroke: 140 mm Daylight: 150/180 mm Heating plant dimension: 250 x 300 mm Max. mass of heating plant: 70 kg Oil reservoir: 100 l Rated power: 19.66 kW Heater capacity: 9.6 kW Vacuum motor power: 2,6 kW Between light curtain and mould area: 270 mm Stroke of vacuum cover: 140 mm The vulcanizing press from manufacturer PAN STONE, model S-V-65-2RT-PCD, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. The machine was part of a production line responsible for manufacturing high-performance seals used in various industries. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany. Hfedpjy Snlxjfx Ad Rjg

Condition: good (used), Year of construction: 1987, functionality: fully functional, Clamping unit heating capacity, 1 heating rod / 8 heating rod: 0,48 / 0,9 kW clamping force: 2 x 500 kN heating plate dimensions: 550 x 600 mm piston stroke: 250 mm diameter of piston, main cylinder: 240 mm diameter of piston, locking cylinder. 39 mm locking cylinder: 260 mm Return capacity: 2 x 600 kN Hsdpfx Asy Snkbjd Rofg dimensions: 2600 x 2100 x 2100 mm weight approx.: 5 t

Condition: good (used), Year of construction: 1994, Clamping Unit: Clamping force: 7,000 kN Operating pressure: 250 bar Specific pressing pressure: 610 N/cm² Number of levels: 2 Installation height with 75 mm heating plate & 20 mm insulating plate: approx. 2x 190 mm Piston stroke: approx. 400 mm Piston 1 diameter: 543 mm Clamping force, rapid traverse: approx. 2 x 85 kN Retraction force: approx. 2 x 47 kN Operating pressure: 300 bar Piston 2 diameter: 60/40 mm Stroke: 400 mm Estimated weight: approx. 16 tonnes Hydraulic System: Hfedpfxsy Sni Re Ad Rsg Pressure adjustment: 40 - 300 bar Flow rate regulation: 0 - 99 % Flow rate l/min (HD): 45 against 300 bar Drive power: 22 kW Tank dimensions (LxWxH): 1000 x 770 x 535 mm Closing Speed: Rapid traverse: approx. 40 - 50 mm/s Slow closing: approx. 0 - 20 mm/s Pressing speed: approx. 0 - 3 mm/s Slow opening: approx. 0 - 20 mm/s Opening, rapid traverse: approx. 0 - 60 mm/s

Condition: used, Year of construction: 2005, functionality: fully functional, Clamping force: 4900 kN Working pressure: 206 bar Heating plate dimensions: 700 x 700 mm Hodpfx Adsy Sniwj Refg diameter of piston: 558,8 mm max. stroke: 250 mm daylight: 300 mm max. mass of heating plant: 560 kg capacity of oil tank: 1100 l rated capacity: 82 kW heating capacity: 56 kW enginge output, vacuum motor: 4 kW Stroke of vacuum cover: 200 mm dimensions: 3975 x 2935 x 2555 mmm Equipped with a crane runway (monorail) with three chain hoists Producer: STHAL Year: 2011 Lifting capacity: 3 x 400 kg Lenght of crane runway: ca. 3500 mm Rolling chassis Lifting capacity: 400 kg Lifting height: 3000 mm stroke speed - main stroke: 4 m/min stroke speed - fine stroke: 1 m/min The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: new, Year of construction: 2024, functionality: fully functional, Discover the powerful Durma press brake at our demonstration center in Saerbeck. As a manufacturer, we offer you maximum precision and efficiency with a capacity of 3050 mm in length and 175 tons. Benefit from our comprehensive all-in-one service: We take care of transportation, installation, commissioning and offer you a one-year warranty as well as fast and reliable service. Visit us and see the quality and versatility of this first-class machine for yourself. Standard equipment Capacity (length - ton) 3050mm - 175t Installation height 530mm Outreach 450mm Stroke 265mm Servo drive Y1, Y2, X - 3 axles Control unit - DT 15 Manuel F. AKAS FPSC safety system CE-Fiessler Akas Servo motor backgauge & linear guide & Ball screw system Manual crowning European tool holder Sliding front arms Hfsdpfxstr Dk Ej Ad Reg Options - DELEM 69S control unit (3D control) -Motorized crowning - 6 axes X=650mm Y1, Y2, X ,R , Z1, Z2 (6 axes controlled press brake) press brake) -Lower tool European M.460R.85 -European upper tool P135.75.R08

Year of construction: 2024, operating hours: 32 h, condition: new, Make: DURMA Type: AD-S 30175 Year of construction: 2020* Hedpfx Ajdx Nluod Rsfg bending length: 3050 mm Press force: 1750 kN Control: DELEM DA-66T Operating hours: 32 h Controlled axes Backgauge: X,R,Z1,Z2,+Delta X +/- 125 mm CNC controlled passage between the uprights: 2600 mm stroke length: 265 mm Installation height: 530 mm table width: 104 mm table height: 900 mm Stands projection: 410 mm travel range X-axis: 650 mm traverse speed X-axis: 500 mm/s travel range R-axis: 250 mm infeed speed: 160 mm/s folding speed: 10 mm/s Retraction speed: 100 mm/s Dimensions L/W/H: approx. 4250x1700x2750 mm Weight: approx. 11500 kg Standard equipment Y1,Y2,X,R - X=650 mm Control: CNC Cybelec ModEva 19T - PC 1200 3D SW D-BEND 3D CAD/CAM import & simulation program CNC controlled motor-driven crowning European tool clamping system 60 mm die holder (only for European die system) Throat 410 mm 2 support arms movable from the front with T-slot and tilt stop Backgauge system: Siemens DC Servo motorized with linear guide and ball screw Protective covers CE Marking Extended equipment Safety system CE standard for EU: FIESSLER AKAS-3P motorised+FPSC (SAFETY PLC) Controlled axes Backgauge: X,R,Z1,Z2,+Delta X +/- 125 mm CNC controlled Control: DELEM DA-66T Hydraulic top tool clamping Wila NSCL-II-HC/UPB - PREMIUM - 250 t/m Hydraulic bottom tool clamping Wila NSCR-II-HC-CNC/UPB - PREMIUM - 300 t/m Powerpack for hydraulic clamping AP3-AP4 Bending aid -

Year of construction: 2024, condition: new, The DA-69T control offers both 2D and 3D programming, which includes automatic calculation of the bending sequence and collision detection. The entire 3D machine setup includes multiple tool stations and provides immediate feedback on product feasibility and handling. DA-69T features: - 3D- and 2D- graphical touch screen programming mode - 3D representation in simulation and production - 17-inch TFT colour display with high resolution - Complete Windows Application Suite - Compatible with Delem Modusys (module scalability and adaptivity) - USB, peripheral interface - Open system architecture - Sensor Bending and correction interface - Profile-T3D offline software - great contribution to environmental protection, climate change and the greenhouse effect will thank us, the next generation will thank us too! - Fully electronic drive - Up to 30% higher productivity - Up to 50% energy savings through Start-Stop technology - Faster than hydraulic press brake - Reduced operating costs - Much lower service and spare parts costs (the electric press brake is technically much simpler and almost maintenance-free) - No harmful oil - quiet - efficient - independent of Hyd. Oil - Low noise operation - relaxed and stress-free bending - Complete work area Hjdjd Sak Sepfx Ad Rsfg - Touchscreen operation Machine dimensions: ( L x W x H ): 2.150 mm x 1.650 mm x 2800 mm Technical details: bending length: 1.250mm Free stand passage: 1.300 mm Press

Year of construction: 2024, condition: new, Here a new AD-R 37220 is offered:Bending force: 220 tonsBending length: 3700Pass between uprights: 3100 mmHub: 265 mmInstallation height: 530 mmExtension: 410 mmTable height: 900 mmTable width: 104 mmY Fast speed: 160 mm/sec.Y Working speed: 10 mm/sec.Y Withdrawal speed: 120 mm/sec.X axes Working speed: 250 mm/sec.R axes Working speed (manual): 250 mm/sec.R axes Travel: 250 mm/sec.X axes Distance: 650Length: 4950 mmWidth: 1770Height: 2900Total weight: 14100 kgOptions:CE with manual F.AKAS II M -FPSC-B-C Safety cover Hfjded S I R Tjpfx Ad Reg

Condition: new, The DURMA AD-S 601000 is a powerful hydraulic press brake that ensures the highest precision and efficiency in sheet metal processing. With a pressing force of 1000 tons and a working length of 6 meters, it is ideal for demanding applications, especially when processing large and thick materials. Technical details: - Model: DURMA AD-S 601000 - Pressing force: 1000 tons - Working length: 6 meters Hjdpfx Adovwm A Io Rofg - Control: SKY22 (3D control) - Back stop: 6 axes (X1, X2, R1, R2, Z1, Z2) - Bending aid: AP3-AP4 integrated for optimized handling of heavy workpieces - Condition: As good as new, available immediately Features and advantages: - High bending accuracy thanks to the latest CNC control - Robust construction for a long service life - Flexibility thanks to the 6-axis back stop control - Support for heavy and large sheets thanks to integrated bending aid The machine is available immediately and can be inspected on request. We are happy to provide you with further information or to arrange an appointment.

Year of construction: 2024, condition: new, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data: AD-R 60400 Bending force: 400 tons bending length: 6050 mm passage between the uprights: 5100 mm stroke: 365 mm Installation height: 630 mm Abroad: 510 mm Optional foreign diameter: 750 mm | 1000 mm | 1250 mm table height: 1220 mm table width: 154 mm Y Fast speed: 120 mm/sec. Y Working speed: 8 mm/sec. Hfsdpfxefin Hwo Ad Rjg Y Retraction speed: 100 mm/sec. X axes working speed: 250 mm/sec. R axes working speed: 140 mm/sec. R axes travel: 250 Engine power: 37 kW length: 7500 mm width: 2110 mm height: 3710 mm Weight approx. 35 tons With more than 60 years of experience in research and production of machines for sheet metal working, 8,000 machines produced annually in three technologically advanced production facilities covering a total area of 150,000 m², the Durmazlar Group and its DURMA machines are today among the internationally renowned manufacturers in their sector, whose products are sold in 120 countries. With the branch in Staufenberg near Gießen, Durma Maschinen GmbH is now an important part of the Central Hesse region. Here here we are your direct contact person from the ranks of Durmazlar, who will competently assist you with advice and practical support when it comes to machines for sheet metal processing. Our demonstration center gives you the opportunity to get an overview of our

Condition: new, Year of construction: 2024, Discover the powerful Durma press brake at our demonstration center in Saerbeck. As a manufacturer, we offer you maximum precision and efficiency with a capacity of 3050 mm in length and 175 tons. Benefit from our comprehensive all-in-one service: We take care of transportation, installation, commissioning and offer you a one-year warranty as well as fast and reliable service. Visit us and see the quality and versatility of this first-class machine for yourself. Hodpfx Adsttatbe Rsfg Standard equipment Capacity (length X ton) 3050mm x 175t Installation height 530mm Outreach 450mm Stroke 265mm Y1, Y2, X - 3 axes Control unit - DT 15 Manuel F. AKAS FPSC safety system CE F.AKAS BVLT light barrier and safety cages (for tandem press brakes) Servo motor backgauge & linear guide & Ball screw system (X) Manual crowning European style tool clamping system Sliding front arms Hydraulic block and valves in special design according to worldwide standard -Electrical equipment according to worldwide standard Selected options -Control unit - Delem 66S - NEW -Motorized crowning - X=650mm X,R, Z1, Z2 (6 axes controlled press brake) press brake) -Lower tool European M.460R.85 -European upper tool P135.75.R08

Year of construction: 2024, condition: new, AD-S 40400 ABKANTPRESSEBending force / Bending force ton400Bending length / Bending length mm :4050Distance between columns :3400Y rapid speed / Express speed mm / sec: 100Y working speed / Working speed mm / sec: 8Y return speed / Return speed mm / sec: 80Crowning / Crowning -: Mot.Daylight / Installation height tool passage and penetration depth of your press brake mm: 630Table width / Table width mm: 300Table height / Table height mm: 1040Stroke / Stroke mm: 365Throat depth / Projection mm: 510Support arms / Support arms: 2 piecesBack gauge finger blocks / The backgauge is standard with two finger blocks amount: 2 piecesSpeed of travel in X-axis / Pressing force and speed of your press brake. X - Axle size / sec: 350Travel in X-axis / x-axis Travel directionmm: 750Speed of R-axis(max.) Speed R axis max. mm / sec: 300Travel in R-axis / R axis Travel directionmm: 250Motor power / Motor power kW: 37Oiltank capacity / Oil tank capacity lt: 450Length / Length mm: 5750Width / Widthmm: 2110Height / Heightmm: 3540Weight approx. / Weight approx.kg: 27760X=650mm X,R,Z1,Z2, /AL)CE with manual F. Akas ll M-FPSC-B-C (SAFTY PLC)Upper tool DurmaLower tool DurmaCentral control motor Price plus transport and commissioningWe look forward to hearing from you. Hedpfxod Rlk Ho Ad Refg

Condition: new, Year of construction: 2025, functionality: fully functional, operating hours: 30 h, ✅ 1. Metalworking companies with medium to high volumes 🔹 Series production / repeat parts If you produce many identical or similar parts, automation pays off as it reduces the cost per part and ensures consistent quality. Hfedpfeyb I Azjx Ad Rsg 🔹 High production > 1,000 parts/month The higher the output, the faster the investment pays for itself through increased productivity. ✅ 2. Companies facing skilled labor shortages or high workloads 🔹 Difficulty finding or retaining qualified staff A robot can partially replace skilled operators and safeguard production capacity. 🔹 Night shifts / 24/5 production Robots can work longer and without fatigue → higher output without additional personnel. ✅ 3. Companies with complex bending processes or high quality requirements 🔹 Tight tolerances / minimizing errors A robot ensures consistent repeatability. 🔹 Complex downstream processes (e.g. handling, deburring, stacking) An integrated robot can take over tasks that would otherwise be performed manually. ✅ 4. Manufacturers facing tight deadlines or cost pressure Short delivery times required Automation reduces throughput times. 🔹 Cost pressure due to competition Longer machine utilization and lower unit costs improve competitiveness. ✅ 5. Future-oriented companies 🔹 Industry 4.0 / digitalization An automated press brake can often be integrated more effectively into IT/MES systems. 🔹 Scalable production If you plan to grow in the future, you have a flexible foundation.

Condition: new, Year of construction: 2024, Discover the powerful Durma press brake at our demonstration center in Saerbeck. As a manufacturer, we offer you maximum precision and efficiency with a capacity of 3050 mm in length and 320 tons. Benefit from our comprehensive all-in-one service: We take care of transportation, installation, commissioning and offer you a one-year warranty as well as fast and reliable service. Visit us and see the quality and versatility of this first-class machine for yourself. DURMA press brake AD-S 30320 Standard equipment Capacity (length X ton) 3050mm x 320t Installation height 630mm throat 450mm Stroke 365mm Y1, Y2, X - 3 axes Control unit - DT 15 CE Fiessler Akas manual light barrier Servo motor backgauge & linear guide & Manual crowning European style tool clamping system Sliding front arms Hydraulic block and valves in special design according to worldwide standard Electrical equipment according to worldwide standard Options: Delem 66T Hedpot Dvl Uefx Ad Rjfg Motorized crowning Motorized X, R-axis backgauge X=650mm X and R Lower tool European M.460R.85 Top tool European P135.75.R08

Condition: new, Year of construction: 2025, The DURMA AD-S 611600 is a powerful hydraulic press brake that ensures the highest precision and efficiency in sheet metal processing. With a pressing force of 1600 tons and a working length of 6 meters, it is ideal for demanding applications, especially when processing large and thick materials. Technical details: - Model: DURMA AD-S 611600 Hjdpfx Aevy Srasd Refg - Pressing force: 1600 tons - Working length: 6 meters - Condition: As good as new, available immediately Features and advantages: - High bending accuracy thanks to the latest CNC control - Robust construction for a long service life - Flexibility thanks to the backgauge control - Support for heavy and large sheets thanks to the integrated bending aid The machine is available immediately and can be inspected on request. We are happy to provide you with further information or to arrange an appointment.

Year of construction: 2024, condition: new, Make: DURMA Type: AD-R 40400 Year of construction: NEW bending length: 4050 mm passage between the stands: 3400 mm Stroke: 365mm Installation height: 630 mm Throat: 510mm table height: 1050mm table width: 154mm Y high-speed: 140 mm/sec. Y working speed: 8mm/sec. Y retraction speed: 120mm/sec. X-axis working speed: 250mm/sec. R axes travel: 250 Engine power: 37 length: 5750 mm width: 2110mm height: 3540mm Weight: approx. 25000 kg Standard equipment Control: CNC Cybelec ModEva 19T CNC controlled motor-driven crowning European tool clamping system / or on customer request Durma clamping system Extended equipment: Safety system CE standard for EU: FIESSLER AKAS II M-FPSC-B-C (SAFETY PLC) Controlled axes Backgauge: X1,X2,R1,R2,Z1,Z2 Control: DELEM DA-66T Delem 66T - 69T or Durma control is selectable Hfjdsd Hy Huopfx Ad Rjg DAM - Durma angle measuring system Hydraulic top tool clamping Wila NSCL-I-HC/UPB - PRO - 180 t/m Hydraulic bottom tool clamping Wila NSCR-I-HC-CNC/UPB - PRO Powerpack for hydraulic clamping D-BEND 3D CAD/CAM import & simulation program AP3 & AP4 Bending aid 750mm to 1500 mm selectable Parking area for support arms (1000mm) TANDEM preparation Laser bending line Oil heating Central lubrication manual or motorized Air conditioning for switch cabinet Further machines are ready for demonstration at our premises in Staufenberg. We will be happy to provide you with further information on request

Year of construction: 2024, condition: new, SPECIAL ACTION: Folding press AD-S 1260 length/width/height: 2300mm/1550mm/2850mm Weight: 47000 kg Bending force: 60 tons Hsdpfx Adjd R Dhpo Rofg bending length: 1250 mm Passage between stands: 1050 mm Stroke:160mm Installation height: 530 mm Throat: 450 mm table height: 900 mm table width: 104 mm Y High speed: 200 mm/sec. Y Working speed: 10 mm/sec. Control CYBELEC MODEVA 19T touch screen CE with manual F.AKAS II M -FPSC-B-C (SAFETY PLC) Europ. upper tool P97.75.R08 (one of them in pitch) Europ. lower tool M.460R.85 (one of them in pitch) Manual quick clamping Y1, Y2, X, R (4 axes) X=650mm X,R CNC controlled motorized crowning 60mm die holder (only for european dies) Overhang 410 sliding support arms at the front with T-slot, clip stop and guidance along the entire line Backgauge : Siemens DC Servo motorized & linear guide & ball roller system Support arms 2 pieces Stop finger 2 pieces With foot pedal Oil capacity: 100l Price is valid from Staufenberg. The machine can be viewed and demonstrated at any time by appointment in our demonstration centre in Staufenberg. Further machines are ready for demonstration at our premises in Staufenberg. We will be happy to provide you with further information upon request.

Year of construction: 2024, condition: new, YOU BUY DIRECTLY FROM THE MANUFACTURER Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data on request. Standard equipment Y1, Y2, X, R - 4 axes Control unit - CNC DT 15 Servo motor backgauge & linear guided ball screw system (X-R) CNC Crowning European type tool clamping system Movable support arms (with T-slot and stopper) Specially designed hydraulic block and valves according to worldwide standard electrical equipment according to worldwide standard Optional equipment CE Manuel F. AKAS II M FPSC-B-C + safety covers with switch CE F. AKAS-LC II AKAS-3 M Motorised + FPSC (Safety PLC) CE BLVT safety - only for tandem machines Hodpjfirwmjfx Ad Rofg Z1, Z2 Axes X1, X2 Axes R1, R2 Axles Delta X axis, +/- 250mm stroke or +/- 125mm CNC controlled X axis = 1000 mm - rear protection with light barrier AP3-AP4 Bending aid Height-adjustable laser angle measurement system Quick clamping system Hydraulic and pneumatic tool clamping system Upper and lower tool Lower tool positioning system Parking area Central lubrication system Oil cooler Additional stop finger and additional movable support arms Special packaging for overseas transports _____ With over 60 years of experience in research and production of machines for sheet metal working, 8,000 machines produced annually in three technologically advanced manufacturing facilities

Year of construction: 2024, condition: new, Länge/Breite/Höhe: 3200mm/1550mm/2750mm Weight: 3550 kg Bending force: 60 tons Bending length: 2050 mm Passage between stands: 1700 mm stroke: 265mm Installation height: 530 mm Projection: 410 mm table height: 900 mm table width: 104 mm Y Fast speed: 200 mm/sec. Hedofgz U Sepfx Ad Rsfg Y Working speed: 10 mm/sec. Control CYBELEC MODEVA 19T touch screen CE with manual F.AKAS II M -FPSC-B-C (SAFETY PLC) Europ. upper tool P97.75.R08 (one of them in pitch) Europ. bottom tool M.460R.85 (one of them in pitch) Manual quick clamping Y1, Y2, X, R (4 axes) X=650mm X,R CNC controlled motor-driven crowning 60mm die holder (only for european dies) Overhang 410 sliding support arms at the front with T-slot, clip stop and guide along the entire line Backgauge : Siemens DC Servo motorized & linear guide & ball roller system Support arms 2 pieces Stop finger 2 pieces With foot pedal Oil capacity: 100l Price is valid from Staufenberg. The machine can be viewed and demonstrated at any time by appointment in our demonstration centre in Staufenberg. Further machines are ready for demonstration at our premises in Staufenberg. We will be happy to provide you with further information on request.

Year of construction: 2024, condition: new, Bending performance 2200 KN Bending length 3050 mm Continuity betw. d. stands (mm) 2600 mm Stroke length (mm) 265 mm Throat depth 410 mm Height 530 mm Operating speed (mm/sec) Y 10 mm / sec Motor power 18.5 KW Operating speed (mm/sec) X 500 mm / sec Operating distance R (motor operated) 350 mm length 4250 mm Width 1700 mm 2750 mm Weight 11500 kg Standard equipment: Y1, Y2, pressure beam - axes (individually controllable) X, R - axes CNC controlled. Control unit - CNC ModEva 15t Servomotor back gauge & linear ball circulation spindle system with Rails (x-R) (AL) CNC controlled crowning European tool clamping system Mobile support arms (with T-slot and stopper) Specially designed hydraulic block and valves for worldwide standard Hfjdpfx Adjd Afxks Reg electrical equipment according to global standard Special Accessories: Control DELEM DA-66T (2D graphic, 3D visualization) Bend - 66.5 (one) = upper tool H thereof in pitch bend - lower 4V that (one of them in Division) D-bend 3D CAD /.

Year of construction: 2024, condition: new, Axes : Y1, Y2, X, R Control : Delem 66 T or 69 T selectable CE Norm with manual Fiessler AKAS II M -FPSC-B-C + safety cover & switch Durma upper tool Hsdpfx Asfin Hced Rjfg Durma lower tool CNC controlled motorized crowning Throat standard 510 mm or selectable 750mm ,1000mm Backgauge: motorized & linear guide & ball roller system Backgauge finger height adjustable Backgauge Motor: AC type sliding support arms with linear guidance along the entire length Technical data on request

Year of construction: 2024, condition: new, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data on request. Standard equipment Y1, Y2, X (3-axis) Y1, Y2, X = 650 mm (double guide, aluminium) Software D-BEND for 3D bending simulation and alignment Manual crowning R axis, manual Backgauge with motor, linear guide and ball screw Backgauge with height adjustment (R-axis, manual) CE-die holding system (upper dies) Front support arms for sheets, sliding (with T-channel and stops) Hydraulic blocks and valves in special design, according to the worldwide applicable standards Electrical equipment, in accordance with the standards applicable worldwide Optional extras: Software D-BEND for 3D bending simulation and alignment R axis CNC (X = 650mm), X, R (double guide, aluminium) Upper dies, CE Lower dies, CE Lower dies, DURMA company Fast die locking system CNC-controlled crowning, with motor Backgauge (1000 mm) - Rear guard with light barrier Oil cooler Additional stop finger and additional front support system Sheets, sliding Special Overseas Packaging 8 meter press brake 320 tons. Hsdpfx Adjfiqdcj Rsfg Bilk9emkq3 With over 60 years of experience in the research and production of machines for sheet metal working, 8,000 machines produced annually in three technologically advanced production facilities covering a total area of 150,000m², the Durmazlar Group and its D