Used Forging Manipulators for sale (476)

Condition: used, TECHNICAL DETAILS - Parts per minute : 300 - Cutting diameter : 6 [mm] - Die ejection : 55 [mm] - Floor space (width) : .97 [m] - Floor space (length) : 2.77 [m] - Motor : 7.5 [hp/kW] - Net Weight : 3500 [kg] - Gross Weight : 4100 [kg] Fodpfx Aeuhb T Dohnoph EQUIPMENT - Tooling as per photo - Positive ejection on 2 punches - Ejector retraction in die - Various spare parts

Condition: used, TECHNICAL DETAILS - Parts per minute : 300 - Cutting diameter : 6 [mm] - Die ejection : 55 [mm] - Floor space (width) : .97 [m] - Floor space (length) : 2.77 [m] - Motor : 7.5 [hp/kW] - Net weight : 3500 [kg] - Gross weight : 4100 [kg] EQUIPMENT - Equipped with ejector recoil between rough part and finishing (RLKO) - Positive ejection (TKO) Fpsdpfx Ahsuhb Twsneh - Tooling as per photo

Condition: used, TECHNICAL DETAILS Fpsdpfx Ajuhb Tqjhneh - Parts per minute : 450 - Cutting diameter : 4 [mm] - Die ejection : 25 [mm] - Floor space (width) : .74 [m] - Floor space (length) : 1.88 [m] - Motor : 4 [hp/kW] - Net Weight : 1600 [kg] - Gross Weight : 2100 [kg] EQUIPMENT - Tooling as per photo

Condition: used, TECHNICAL DETAILS - Parts per minute : 400 - Rivet length : 12 [mm] - Drilling depth (max.) : 5 [mm] - Cutting diameter : 3 [mm] - Floor space (width) : 1.12 [m] - Floor space (length) : 2.21 [m] - Height : 1.77 [m] - Motor : 4 [hp/kW] - Net weight : 2,500 [kg] - Gross weight : 3,000 [kg] EQUIPMENT Fpedpfx Aheuhb Tkoneh - Tooling as per photo

Condition: new, mileage: 100 km, power: 368 kW (500.34 HP), axle configuration: 4x4, color: white, driver cabin: sleeper cab, gearing type: automatic, Equipment: ABS, EBS, air conditioning, - Brake system Fjdjy Svtdjpfx Ahnjph For vehicle inquiries, Mr. Seidel will assist you (via phone). co X-Way AS440S50T/P HI-TRACTION 4x4 tractor unit Emission standard EURO VI E, DRIVE T. 315/80R22.5, speed limiter 90 km/h, electrically operated roof hatch, transparent with MLL high roof, front underrun protection for chassis with a total mass exceeding 7,490 kg, first aid kit, hybrid bumper, electrically adjustable and heated exterior mirrors, standard cab roof insulation, COC general operating permit, 10-inch instrument cluster, fully automatic air conditioning, digital tachograph 4.1, static passenger seat, axle weight variant: front axle 8,000 kg / rear axle 11,500 kg (technically possible up to 13,000 kg), smart alternator 2880 W (24V x 120A), demand-controlled, rear axle air suspension, parabolic suspension on front axle, batteries in frame overhang, standard labeling for air tanks, rear shock absorbers, moderate climate version, 2-cylinder air compressor 630 cc, chassis frame in grey, standard total train brake, exhaust tailpipe left, air filter unit under cab, mechanical battery disconnect switch on chassis, right side, standard frame setting, trailer dual-circuit brake, fifth wheel dimension EU, trailer socket for 24 volt operation, 15-pin, rear axle ratio: i 2.85, rear overhang 1047 mm, ECO NORMAL MODE, standard gearbox mode, Connectivity Box 4G incl. TCO service contract, STANDARD SETTING CURSOR 13, tire pressure monitoring system (TPMS) with internal sensors, 4 DIN slots, VDI interface (Vehicle-Data-Interface) for telematics (FMS), version 4.0, gearbox software ECO-Roll (coasting function), adaptive cruise control (ACC), lane departure warning system (LDWS), driver drowsiness attention warning, warning triangle in accordance with ECE-27 guideline, standard catwalk behind the cab, hill start assist (Hill Holder) for comfortable starts on slopes, electronic stability program (ESP), reversing monitoring system with camera, blind spot information system (BSIS) right side, intelligent speed assist (ISA), NO HIGHWAY ASSIST, side marker lights, front area monitoring (MOIS), advanced emergency braking system (AEBS), pneumatic parking brake, prewiring for alcohol interlock (ALC) with cable, CAMBIO 12TX 2460 TD, CEE type plates, standard EU vehicle width, HI-TRACTION incl. hydraulic crawler mode, Alcoa aluminum rims, forged matte, Hi Traction preparation, PTO NH/4C with pump connection suitable for Meiller tipper or crane tipper, electrically operated cab tilting mechanism, hybrid bumper painted in cab color, AS cab with standard roof (MY24), storage compartments left and right, one-piece lower bunk, comfort/cushioning – soft, with adjustable head section, ashtray in center console, electronic immobilizer and 3rd vehicle key, switch in dashboard for the lift axle of the semitrailer, fifth wheel Jost, fifth wheel height: 150 mm + mounting plate height: 50 mm, fuel tank 480 liters, left, aluminum, AdBlue tank 135 liters with integrated step (for CM chassis and 4x2 tractor unit), 145 liters without step, override of ECO SWITCH limiter possible, expansion module for controlling PTOs, amber warning lamp,...

Condition: used, TECHNICAL DETAILS Fedpfxjyuzggo Ahnjph - Maximum workpiece diameter : 80 [mm] - Z-axis travel : 220 [mm] - Max module : 2.5 - Max workpiece-holding spindle speed : 3000 [rpm] - Max dimensions of the hob (diameter x length) : 118 X 120 [mm] - Speed of the hob-holding spindle : 200-5000 [rpm] - Shifting travel : 140 [mm] - Angular travel of hob-holding headstock : -45/+115 [°] - Machine floor space : 2700/2180 [mm] - Machine height : 2310 [mm] - Machine weight : 4800 [kg] EQUIPMENT - CNC : Siemens 840D PowerLine - Loading manipulator

Condition: used, TECHNICAL DETAILS - Maximum workpiece diameter : 80 [mm] - Z-axis travel : 220 [mm] - Max module : 2.5 - Max workpiece-holding spindle speed : 3000 [rpm] - Max dimensions of the hob (diameter x length) : 118 X 120 [mm] - Speed of the hob-holding spindle : 200-5000 [rpm] - Shifting travel : 140 [mm] - Angular travel of hob-holding headstock : -45/+115 [°] - Machine floor space : 2700/2180 [mm] - Machine height : 2310 [mm] - Machine weight : 4800 [kg] EQUIPMENT Fpedpfx Ajyuzgashnjh - CNC : Siemens 840D PowerLine - Loading manipulator

Condition: used, Anvil with round horn and rectangular horn Northern German style anvil Face width: 130 mm Fedpfxoy Ehycj Ahnoph Face length: 630 mm (with pointed horn) Round horn length: approx. 200 mm Pointed horn length: approx. 220 mm Overall length: 830 mm Height: 340 mm Foot with front anvil: 430 x 320 mm - Cast steel, hardened - Square hole approx. 28 mm for anvil tools - Round hole Ø approx. 23 mm Dimensions L x W x H: 830 x 320 x 340 mm Very bright ring, good quality

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 1,860 mm, total length: 2,800 mm, total height: 910 mm, overall weight: 600 kg, input current: 16 A, warranty duration: 12 months, type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, GLASS CUTTING TABLE - MANUAL - New MODEL: SDRM FULL Manufacturing year 2026 - brand new We manufacture glass cutting tables in various equipment configurations. Our products are characteristic for top functionality and service life because we processed flat glass and we know what customers expect from these machines. Our tables have been operating for a few years in glass processing plants on 3 continents. Our long-term experience enables us to design a machine whose functionality and quality satisfies the needs of our customers to the fullest extent. TABLE EQUIPMENT: - manually slid supports for vertical loading (covered with replaceable ash trees blocks) - 4 swivelling polyamide castors Ø80 for extreme loads of table movement - 4 adjustable feet for levelling the table in the operation place - table top surface - extremely resistant black felt - table top surface circumference covered with milled ash tree strips - 2 steel panels screwed beneath facilitating loading by means of a forklift - bottom base beam filled with vibrated concrete with steel reinforcement and dispersed concrete from polypropylene fibres in order to increase the stability and rigidity of the structure - pneumatic pivoting (the vertical and horizontal levelling of the table top surface) by means of an actuator with a hydraulic speed controller - breaking strips (breakers: longitudinal and transversal) controlled pneumatically by means of pedals mounted on the sliding foot panel with automatic return Fsdpfxsd Tamde Ahnoph - an airbag with installed high pressure fan enabling the easy manipulation of heavy panes on the top surface (the fan is activated by means of a pedal on the foot panel and two additional switches mounted on the top surface circuit blow in the air under the panes, reducing friction significantly) - adjustable height of breaking strips sliding from the table top surface. BASIC TECHNICAL DATA: - weight: 600 kg - top surface size: 286 cm x 186 cm - height: 91 cm (adjustable +/- 2 cm) - electrical connection: 16 A 5 pin plug - air connection: standard 7.2 NW - air working pressure: 7 bar - fan power: 2.2 kW - voltage: 400 V 50 Hz DOCUMENTS ATTACHED TO THE MACHINE: - Declaration of Conformity with the applicable machinery standards - CE Marking - UE EMC Declaration - 12 months’ warranty - User’s Manual (in Polish and in English) This product is supplied ready for operation. Our company can also deliver the table within the EU and to other countries.

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 1,860 mm, total length: 2,800 mm, total height: 910 mm, overall weight: 600 kg, warranty duration: 12 months, GLASS CUTTING TABLE - MANUAL - New MODEL: SDRM FULL Manufacturing year 2026 - brand new TABLE EQUIPMENT: - manually slid supports for vertical loading (covered with replaceable ash trees blocks) - 4 swivelling polyamide castors Ø80 for extreme loads of table movement - 4 adjustable feet for levelling the table in the operation place - table top surface - extremely resistant black felt - table top surface circumference covered with milled ash tree strips - bottom base beam filled with vibrated concrete with steel reinforcement and dispersed concrete from polypropylene fibres in order to increase the stability and rigidity of the structure Fpsdjh D Rnhopfx Ahnjh - pneumatic pivoting (the vertical and horizontal levelling of the table top surface) by means of an actuator with a hydraulic speed controller - breaking strips (breakers: longitudinal and transversal) controlled pneumatically by means of pedals mounted on the sliding foot panel with automatic return - an airbag with installed high pressure fan enabling the easy manipulation of heavy panes on the top surface (the fan is activated by means of a pedal on the foot panel and two additional switches mounted on the top surface circuit blow in the air under the panes, reducing friction significantly) - adjustable height of breaking strips sliding from the table top surface. BASIC TECHNICAL DATA: - weight: 600 kg - top surface size: 286 cm x 186 cm - height: 91 cm (adjustable +/- 2 cm) - electrical connection: 16 A 5 pin plug - air connection: standard 7.2 NW - air working pressure: 7 bar - fan power: 2.2 kW - voltage: 400 V 50 Hz DOCUMENTS ATTACHED TO THE MACHINE: - Declaration of Conformity with the applicable machinery standards - CE Marking - UE EMC Declaration - 12 months’ warranty - User’s Manual (in Polish , English)

Condition: used, Year of construction: 2011, We are offering this used Pacepacker Services Blu‑Robot Manipulator (Model 2.8/120) for sale. The robotic arm is in well-maintained condition and comes from industrial use. Ideal for applications such as material handling, packaging, palletizing, or automation processes. Technical specifications (according to nameplate): Manufacturer: Pacepacker Services Ltd., England Fodpsy Rr Dvjfx Ahneph Model: Blu‑Robot Manipulator (2.8/120) Serial number: M11‑0239 Year of manufacture: 2011 Condition: Used, fully functional If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, machine/vehicle number: 3218, functionality: fully functional, Boldrini PAO 1000 Hydraulic Dishing Press, 1,000 tonne capacity Fodeyztnwspfx Ahnoph 6,000mm distance between frame 2x GH overhead travelling workpiece manipulation cranes with independently supported runway, each with 2x 16 tonne capacity hoists

Condition: used, Year of construction: 2014, machine/vehicle number: 101453, functionality: fully functional, power: 368.5 kW (501.02 HP), pressing force: 4,000 t, stroke length: 1,600 mm, operating speed: 200 mm/s, ram plate width: 1,900 mm, ram plate length: 1,900 mm, clearance between the columns: 6,500 mm, overall weight: 480,000 kg, Fagor JBe-4000-2.5x2.5-2013 4,000T Hydraulic Forming Press (2014) 0–4,000 tonnes variable ram pressure 1,900mm ram diameter Fpsdpfeyzr Hfex Ahnsh 2,500 mm x 2,500 mm T slotted top platten 2,500 mm x 2,500 mm T slotted bottom platen 6,500 mm distance between side columns 1,600 mm length of ram stroke 200 mm/s ram speed 12 mm/s pressing speed 368.5 kW total electrical power 480 tonnes total weight of machine 2x overhead travelling workpiece manipulation cranes with independently supported runway, each with 2x 16 tonne capacity hoists Siemens programmable touch screen console for machine and cranes

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Fpedofz Dubjpfx Ahnsh Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Use of one photocell Using one photocell in the space of workpiece allows you to measure the length of the workpiece and, consequently, gives you the opportunity to turn on the guns when the item is in range, and to switch off the gun immediately after the workpiece is finished. The photocell is included in the standard equipment.Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus braking the energy and powder coating. Vertical detection of the detail of the workpiece. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. Application of light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to manipulate the manipulators. Benefits of using gates and photocells The benefits of using photocells or light gates are primarily energy and powder savings. Eliminate painting of a zone in which there is no detail. With the use of light gates, precise control of the guns. Our lines can be optionally equipped with photocells, or light gates Using one photocell in the workpiece space allows you to measure the length of the workpiece and, consequently, gives you the ability to turn on guns when the item appears in their range, and turn off the gun immediately after the workpiece is finished.Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus saving the energy and powder.The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time in which the detail will appear in the gun space - allowing guns to be selectively switched on or off.Using of light gates with multiple sensors horizontally and vertically Fpsdpfx Aofy T Arshnoh This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to adjusting the manipulators.The benefits of using photocells or light gates are primarily powder and energy savings Eliminate painting of a zone in which there is no detail With the use of light gates, precise control of the guns The PLC counts the time at which the detail should appear in the gun space - allowing guns to be selectively switched on or off.

Year of construction: 2020, condition: new, Automation Use of one photocell Using one photocell in the space of workpiece allows you to measure the length of the workpiece and, consequently, gives you the opportunity to turn on the guns when the item is in range, and to switch off the gun immediately after the workpiece is finished. The photocell is included in the standard equipme Array of guns Vertical 8pcs. pistols Control - profiControl 10 " Cyclone - CK-D1250 Dust collector - OZ-8H Center - RP-01 + SV-200 MA1-23 x 2 pcs manipulator Os X MX-100 x2 pcs. Horizontal goal - Horizontal goal W400 x2 items Fodpoflq Spefx Ahnoph Vertical gate - H2000 vertical gate The maximum painting speed is 1,65714285714286m / min 0 piece pulling machines Pow. requires 10188m3 / h to fly Required min. cabin passage W900mm H2100mm Pipe diameter 500mm - 16.9m / s minimum 16m / s Air consumption 1210 L / min + Sug. SC-20 compressor Min.current connection 28.14 kW Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus braking the energy and powder coating. Vertical detection of the detail of the workpiece. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time at which the detail should appear in the gun space - allowing guns to be selectively switched on or off. Application of light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to manipulate the manipulators. Benefits of using gates and photocells The benefits of using photocells or light gates are primarily energy and powder savings. Eliminate painting of a zone in which there is no detail. With the use of light gates, precise control of the guns. Our lines can be optionally equipped with photocells, or light gates Using one photocell in the workpiece space allows you to measure the length of the workpiece and, consequently, gives you the ability to turn on guns when the item appears in their range, and turn off the gun immediately after the workpiece is finished. Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus saving the energy and powder. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time in which the detail will appear in the gun space - allowing guns to be selectively switched on or off. Using of light gates with multiple sensors horizontally and vertically This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to adjusting the manipulators. The benefits of using photocells or light gates are primarily powder and energy savings Eliminate painting of a zone in which there is no detail With the use of light gates, precise control of the guns.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Fodpfx Aofz Dt Nehnsph Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. Fjdsfz I D Djpfx Ahneph All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Fedpfx Aofz I Edshnsph The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Fjdpfx Aoflmdwehnsph Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Fjdpfxsfz Dqmj Ahnjph Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Fpjdpfx Aofz Nb Tehnsh Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. Fpedpfofz U S Esx Ahnoh All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: used, Year of construction: 1992, sheet width 2050 mm plate thickness 10.0 mm ST Fsdpjxacdvsfx Ahnsph pre-bending 8.0 mm ST diameter of upper rolls ~ 205 mm side roll diameter ~ 195 mm Control konv. oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight 3200 kg range L-W-H 4500 x 1500 x 1300 mm Features: - Robust electro-hydraulic 3-roll bending machine - 3-roll concept offers a wide range of bending and rounding options - Pivoting control unit at the front * Operation - Control of all rolls and machine axes * Digital position display * Manual operation via joysticks - Diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rolls with a hardness of 53-55 HRC - Low-maintenance, stable machine design - Sturdy welded steel construction - Electro-hydraulic folding bearing for easy pipe removal - Pressure gauge / pressure indicator for the rolls - Safety device (safety lanyard with switch unit) - Operating instructions (PDF)

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: R14101358 (Roboter) / E14130752 (Steuerschrank), overall weight: 1,270 kg, load capacity: 250 kg, arm reach: 2,655 mm, controller manufacturer: FANUC, controller model: R-30iB, input voltage: 400 V, FANUC industrial robot Robot R-2000iB 250F, Year of construction 01.2014 (control cabinet 12.2013). Axes: 6, Reach: 2,655 mm, Load capacity: 250 kg. Dimensions: Length 200 cm, width 110 cm, height 185 cm. Control cabinet: FANUC R-30iB. Complete with robot manipulator, connection cable, teach panel, control unit. (See type plates for further details). IPendant A05B-2255-C101#EGN We also offer accessories such as bases, spot-welding guns, rotary tables and much more. We are also happy to demonstrate the robot. Fpjdstk N E Topfx Ahnjh Packaging and loading included.